Search Documents

By George F. Becker

Complexity of Rock-Fractures. - The strains to which rocks have been subjected are manifestly very complex, and it is entirely safe to presume that every possible node of deformation and rupture is exemplified. The most superficial inspection of any ordinary mountain region is sufficient to assure the observer that the rocks have been pressed, stretched, bent, buckled, twisted, and shorn. The study of torsional rupture cannot fail, therefore, to throw light on geological phenomena. The question is, how areas which have been broken in this manner are to be distinguished from those which have yielded to other systems of forces. Phenomena of Joints. - It is well known that a large part of the more homogeneous rocks and some very heterogeneous rocks are intersected by partings, often called joints. These partings are frequently flat surfaces, even when seen in very large exposures, but are sometimes surfaces of moderate single or double curvature. Joints usually occur in groups, in each of which the several partings are parallel to one another, and several such groups often intersect the same rock-mass. In such cases the different systems make large angles with one another. Nearly all students of the subject of jointing have reached the conclusion that joints are faulted surfaces, the dislocations usually being of small amplitude; and this conclusion receives abundant support from the study of thin sections under the microscope. It has thus been shown that much even of what would be regarded in I hand-specimens as mere slaty cleavage consists, in reality, of innumerable microscopic faults. For this reason, Mr. Daubrée rejects the term "joint," as failing to imply the existence of relative motion, and has introduced the terms “diaclase” and “paraclase” as substitutes.1

Jan 1, 1913

Freeman, the English historian, said that he had learned from Macaulay "never to be afraid of using the same word or name over and over again if by that means anything could be added to clearness or force. Macaulay never goes. on, like some writers, talking about ' the former ' and 'the latter ', 'he ', 'she ', 'it), and 'they’, through clause after clause, while his reader has to look back to see which of several persons it is that is so darkly referred to". He might have learned also from Macaulay that a preposition makes a feeble ending for a serious statement. How often do you hear 'the former' and 'the latter' in conversation? Good conversation is a guide not to be disdained. When you must use 'the latter ', do not confuse it with 'the last '. Cheap labor, cheap fuel, and cheap transport are essential, the latter [last] being particularly important in base-metal mining. The apparatus may be used to determine such gases as hydrogen sulphide, chlorine, oxides of nitrogen and some others, as well as sulphur dioxide. In the case of the latter two, etc. The two last mentioned are "sulphur dioxide" and "some others". He should have stated which two, and he should have avoided that wretched phrase "in the case of ". Pinning may be partly prevented by use of chalk, oil, or turpentine. The latter [last] is beat. "Partly prevented" is a poor phrase. 'Prevented' is a word that does not lend itself readily to modification. He means ' checked ' or 'corrected '. These steps are necessary to produce the gas, crude oil, and ammonia, the latter [last] of which is in solution in the water obtained along with the oil.

Jan 1, 1931

By Harold Rose

THE peak of production from the Appalachian natural gas field was apparently reached about 10 years ago, and the annual production from Pennsylvania, West Virginia and Ohio has now dropped to about two-thirds of the amounts obtained in 1916 and 1917. This .falling off in production has occurred in spite of vigorous efforts and large expenditures by producing companies to maintain or increase their output. The greatly increased costs of development and handling are reflected in the present average value of natural gas at the point of consumption, which value in the three states referred to, has more than doubled in the past 10 years. While it is true that the natural gas production of the United States has increased during recent years, this increase has come from southwestern states, particularly from Oklahoma, California, Louisiana and Texas, which states are now leaders in the production of this valuable but fleeting resource. Pennsylvania, originally the leading state in natural gas production, occupies sixth place in the latest (1924) U. S. Bureau of Mines statistics. West Virginia, which held first place for 15 years, has dropped to third rank, and Ohio is the seventh state in the order of natural gas production. Domestic and industrial demands for gas are constantly increasing everywhere in the United States. These growing demands have accentuated the difficulties in the localities with depleted natural gas supplies, and serious shortages have already occurred during winter months in the Pittsburgh district. Some relief has been obtained by placing restrictions on the industrial use of natural gas, and by increasing the price (which tends to reduce consumption). Yet these are but temporary expedients for checking gas consumption, which fail to solve the problem of adequate future supplies of gas.

Jan 10, 1926

By N. K. Chen, R. Maddin, R. B. Pond

A METHOD has been described by Andrade' for obtaining very rapid grain growth so that single crystals of high melting point metals could be made with comparative ease. The furnace construction was essentially a very thin wire through which was passed an electrical current so that "a high uniform temperature" was maintained. The wire was surrounded by a fused quartz tube from which the air had been evacuated. Andrade applied this method to the growth of single-crystal wires of alpha iron, and Tsien and Chow2 prepared single crystals of molybdenum 0.25 mm diam in this way. In the present report a method is described in which the basic idea of the Andrade furnace is utilized. However, modifications are employed so that large single crystals of molybdenum or of any refractory metals can be grown. Furnace The modified Andrade furnace is shown in Fig. 1, and the detailed drawing of its construction can be seen in Fig. 2. The furnace proper consists of a 2'/2-in. diam fused silica tube, 20 in. long, which is evacuated continuously at the bottom. Two water-cooled copper electrodes hold the specimen by means of collets held in place in the electrodes by set screws. These electrodes serve also to transmit power to the specimen. The lower electrodes can be clamped to the stand, while the upper electrode is fastened in place to the bellows which in turn is further connected to one side of the lever arm, flexibly supported at the top. After the specimen is mo;nted- and the vacuum is secured, the lever arm is adjusted by means of the counter weight so

Jan 1, 1952

By John V. Beall

Homeland of the Republic of China, the island of Taiwan looks on the map like a seal, muzzle pointed south, resting complacently on the emerald waters of the China Sea. Any notion of placidness is quickly dispelled by going to that country where the visitor gains the impression of almost violent busyness in tearing up streets, pushing up buildings and tilling the fields. Driving from the airport downtown to Taipei, the capital city, one sees roads, streets and thorough-fares which seethe with bizarre traffic. From water buffaloes to buses, transportation takes every conceivable shape, size and color in between. The load being transported need not conform in any way to the capabilities of the vehicle. Twenty- foot lengths of pipe may be trans- ported on a bicycle. A family of five may go to town on a motor- cycle. Impossible? Count them. The streets and buildings of the city appear unrestrained, or without margins. Shops do not end at the doorway but overflow with a variety of goods onto the sidewalks and into the streets where the marginal traffic, on foot or on wheels, intertwines unconcernedly with the flotsam from the shops. Signs, dry goods, hardware and the continuous hubbub make the view colorful, lighthearted and fascinating. The island is 230 miles long by 75 miles wide with a central mountain spine. To the east, the mountains descend steeply to the ocean whereas to the west, beyond the foothills, there is a broad coastal plain. Only about 25% of the land is suitable for cultivation but the tropical climate permits several harvests a year. At the same time the mountains, which are high enough to sometimes have snow, offer an agreeable change of temperature. In this setting, society has created an economy that is growing at such a rate on all fronts that it would seem to be fairly bursting at the seams.

Jan 9, 1969

By C. W. Tomlinson

INTRODUCTORY THE analyses which have been made by the writer according to the method described below were made as part of Professor Withey's investigation of the concrete aggregates' of Wisconsin, in the hope of throwing light on the extent and nature of the influence of the mineralogical constitution of aggregates upon the properties of the concrete, and mortar made from them. This method was found most satisfactory after four weeks of experiment and modification. It attains an accuracy quite sufficient for the purpose of the analysis, and is fairly rapid. Mineralogical analyses may be thus made at a cost considerably less than that of chemical analyses of a similar degree of completeness. The results obtained by this method should not vary in any item by more than 1 per cent. of the total weight of the sample, and may be made very much better than this by the exercise of greater care in the microscopic counting (see below). The accuracy of the hand sorting 'is of course dependent upon the experience and carefulness of the analyst. . After a month's practice, the writer was enabled to turn out these analyses at the rate of four in 33 hr. of working time. It was found most economical to handle four samples at once. The samples analyzed weighed froth 290 to 340 g. each. The same method could be applied to larger or to smaller samples, within reason able limits. The following list covers the necessary apparatus and equipment: 1 good balance capable of weighing accurately to tenths (or, better, hundredths) of a gram, and of handling quantities up to 200 g. in weight. 1 Westphal balance, registering densities to two or three decimal places. 1 Meker or Bunsen burner, and gas supply. 1 nest of sieves, 10, 20, 40, and 100 meshes to the inch.

Jan 5, 1915

By W. L. Austin

The advance made in recent times in this branch of metallurgy is indicated by the attention the subject is receiving from important American copper-producing companies. Reference to the files of publications devoted to the mining industry discloses that some 20 American companies are actively investigating the amenability of their ore, or other material, to leaching methods, and that plants of varying capacities up to 10,000 tons per day arc under construction or are projected. Several leaching works are in commercial operation. It has been frequently pointed out that no method of leaching is universally applicable, for the reason that each ore differs in some particular from apparently similar ore found elsewhere, and also because local conditions are rarely the same even where the ore closely approximates in character that being worked at some other point. For this reason the older companies are approaching the matter in a conservative manner, experimentally determining for themselves the salient features in each instance. In considering a leaching proposition three factors at once fix the attention: (1) disengaging the metal from mineralized forms in which it is found in nature; (2) recovering the metal in a commercial state after it has been dissolved; (3) the apparatus best adapted to carrying out the several operations. Bringing the Metal into Solution This feature.has been found to present no serious difficulties. Numerous solvents for copper are known, and it has been repeatedly demonstrated on a commercial scale that from 80 to 90 per cent. of the metal contained in an ore can be rapidly brought into solution. It is interesting to note, however, that all of the companies above referred to have selected sulphuric acid as the basis for a lixiviant. Where oxidized ore practically free from precious metals is treated simple leaching with

Jan 1, 1915

By I. I. Gardescu

Rumania produced during 1936 some 62,500,000 bbl. of oil. Of this production, 99 per cent comes from an area running east and west along the southern foothills of the Carpathian Mountains just north of Bucharest. This almost rectangular area measures 20 by 40 miles and is located in the districts of Dambovita and Prahova between the cities of Targovigte to the west and Mizil to the east. The remainder of the production is about evenly divided between the oil fields north and east of Mizil in the Buzh district and those to the north on the eastern flanks of the Carpathian Mountains in the district of Baciiu. The Transylvanian Basin to the north and west of the Carpathian Mountains has produced to date only dry gas from its numerous salt domes. Bucsani Field The Bucgani oil field produced 15,600,000 bbl., or 25 per cent of the total production of Rumania in 1936. Bucgani is a deep-seated salt dome 7 miles south of the old Moreni oil field. A slight surface doming, not dissimilar to the topography observed on some of the oil fields of the Californian basin, called attention to the area. It is the southernmost oil field and, together with the deep-seated and prolific Boldesti field, points to the great oil possibilities of the deep-seated domes along the northern edge of the Rumanian plains south of the Carpathian foothills. The Government is the principal owner of the oil and gas subsurface rights in the areas south of the foothills. The acquisition of leases by the operating oil companies may be made either by application for an exploration permit, the company being assigned part of the acreage in case of successful wildcatting, or, if the area has already been declared as proven territory, through competitive bidding. A block of 164 acres was auctioned recently for $200,000, or $1200 per acre. The largest producer in the Bucgani oil field is the Steaua Romana, which produced 39.5 per cent of the total for the field. The Steaua Romana is a post-war company and 50 per cent of its shares are owned by the British Steaua and the Steaua Franpaise and the other 50 per cent by a group of Rumanian banks and by the Government. The Colombia,

Jan 1, 1937

By Cyril Stanley Smith, Earl W. Palmer

FOR several years an investigation has been in progress in the research laboratory of The American Brass Co. to determine the thermal and electrical conductivities of most copper alloys of commercial importance and several of scientific interest. This paper contains such data on the binary alloys of copper with silicon, aluminum, manganese and nickel, and on a large number of ternary or more complex alloys. Some interesting general relationships between the thermal and electrical conductivities for all copper alloys at all temperatures are pointed out. The data for the copper-zinc, copper-phosphorus and copper-tin binary systems have already been publishedl 1,2 † except for the electrical conductivity at 200° C., which is given in the appendix of this paper. LITERATURE ON THERMAL CONDUCTIVITY OF COPPER ALLOYS The papers referred to above contained a summary of the figures available in 1929 for the thermal conductivity of copper alloys. There is given in Table 1 herewith a selection of the data that have appeared since that time. The measurements of Hanson and Rogers3 are particularly interesting since they cover a series of alloys in the alpha solid solution range and show the effect of heat-treatment. Their alloys were tested as annealed castings, and are not therefore directly comparable to the worked alloys measured in the present investigation, although the difference is small. Bailey's determinations4 were carried out on the alloys used by Lees5 in 1906, and extend his results to higher temperatures. It is most unfortunate that the alloys were not analyzed, for the approximate compositions given are hardly sufficient identification of the

Jan 1, 1935

By Robert H. Leach

SILVER the whitest of all metals, has been used for thousands of years. Students of antiquity agree that silver, gold, copper, and their alloys were the first metals discovered by man and they have all played an important part throughout the advance of civilization. Native silver has been found in different parts of the world in varying form and size, such as clusters of fine wires in rock cavities, thin sheets along cleavage planes in veins of rocks, and pieces of irregular shape that vary in size from extremely small particles to masses weighing many pounds. Nearly pure silver is found in, the native state but the native metal is more likely to contain copper or gold. Some of the natural alloys closely approximate the compositions of synthetic alloys that are used in the arts at the present time. As these native silver alloys usually are malleable and ductile, it is evident that prehistoric man was provided by nature with metals that he could work, with the crude tools at his command, into simple ornaments or other articles. The relative scarcity of silver combined with its resistance to attack under ordinary atmospheric conditions have been important factors in determining the purposes for which man has used it. Its scarcity and indestructible character have made its possession particularly desirable, and from the earliest times its principal use has been as a measure of wealth and a medium of exchange. The comparatively high value of silver in relation to other commodities makes it possible to transport a large amount of wealth in small bulk, and silver has traveled back and forth over all parts of the world. Even when made into ornamental pieces, such as bracelets,

Jan 1, 1953

By Walter S. Weeks

THE subject of the flow of air through a mine under the influence of natural ventilation has proved an elusive one. To my knowledge only cut and try algebraic solutions have been used where multiple paths are involved. The object of this paper is to present a method for the graphical determination of the flow induced by the natural ventilation pressure (N.V.P.) alone or in combination with a fan. The N.V.P., measured in pounds per square foot, induced by two columns of air between two horizontal planes at different elevations, is equal to the difference in weight of the two columns, assuming each to have a cross-sectional area of 1 sq. ft. Pressure in pounds per square foot is converted into inches of water by dividing by 5.19. Methods of calculating the N.V.P. have been discussed in the literature. In this paper, for simplification of exposition, the change in pressure due to the weight of superimposed air will be assumed directly proportional to the length of the column. The actual methods of calculating the N.V.P. do not affect the solutions to be presented. It must be realized that the precision to be obtained from the small- scale, inked diagrams presented is not as great as would be obtained from large-scale, penciled curves that would be used in practice. The accuracy of the curves does not warrant reading "volumes" closer than the nearest thousand cubic feet per minute. CASE I. DUCTS IN SERIES The simplest type of problem is to determine the flow when two shafts are connected by a crosscut, as shown in Fig. 1. In this example, the resistance of the shafts is to be taken as 0.0001 in. of water for a flow of 1000 cu. ft. per minute for a length of 1000 ft. The resistance of a crosscut is to be taken as 0.0005 in. of water for a flow of 1000 cu. ft. per minute. The small pressures necessary to cause changes in velocity will not be considered, because the accuracy of other obtainable data does not warrant their consideration.

Jan 1, 1938

By AIME AIME

This volume, in the preparation of which all former annual or collective indexes have been not only compiled but revised, is published for the special benefit of all who do not possess complete sets of the Transactions. And it is published at this particular time, as part of a plan by which it is hoped that the Library of the Institute, which, through liberal donations, has become unexpectedly comprehensive and valuable, may be made useful throughout the world. Thus, any person possessing this Index can ascertain at once what has been published in the Transactions on a given question, and can learn, by writing to the Secretary, what is its nature, whether it is still to be had in pamphlet form, where it can be consulted in a public library, at what cost it can be copied by hand, etc., etc. In short, to those who own complete sets of the Transactions, this Index will be a great convenience; but to those who do not, it will be a professional necessity. The edition now in press is limited, and orders received will be supplied according to date.

Jul 1, 1907

By J. B. Cohen

In an investigation of the microstructure of shock-loaded metal specimens1 C. S. Smith found that there was little distortion of grain boundaries or change in external dimensions, although the hardness corresponded to that produced by severe rolling. Furthermore, the hardness of individual grains was independent of the deformation structures present; grains with no markings were as hard as those heavily populated with markings. These markings which resemble twins do not appear in copper until high shock-loads of the order of 200 kb are applied. It appears that due to the high velocity of a shock wave and its sharp front, heavy deformation takes place on a submicroscopic scale. In this work an attempt was made to examine this deformation, particularly at a load below which macroecopic markings appear. The broadening of 200 and 400 diffraction peaks was examined from the face of a poly crystalline sample normal to the direction of the shock wave. These peaks were chosen because the elastic constants in copper are such that residual strains would be greatest in the <100> directions; hence, the strain-broadening contribution to these peaks would be large in comparison to other sets. Also the broadening due to stacking faults and microtwins would be greatest with this set.2 A complete Fourier analysis of these peaks was made, as described by warren,&apos; using the Stokes correction with peaks from an annealed sample.3 With the aid of the U. S. Army Ordnance Corps EDVAC computer and a curve matching program, sixty sine and sixty cosine coefficients were obtained for each peak. The last of these was about 1.5 pct or less of the largest coefficient, indicating good representation. Transverse sections from a 1.5 in. rod of as-drawn electrolytic tough-pitch copper were reduced in cross-sectional area about 50 pct by cross rolling. Disks 1.5 in. in diam were recrystallized at 275 °C for 30 min and then at 300°C for the same time. The faces were polished and deeply etched in nitric acid to remove 25 mils. The grain size was 0.02 mm. Laue back-reflection patterns indicated the sample was well recrystallized. The two diffraction peaks from this sample were recorded on a Norelco diffractometer using filtered copper radiation. Peak intensities were kept less than 600 cps to assure linearity of the counter and circuitry. This sample was then placed between two rods of the same material and diameter. The top rod was 2.25 in. long and the bottom rod 1 in. long. (In

Jan 1, 1961

By Edwin Chance

DURING the past 10 years, the safe and efficient lighting of the coal mines of this country has received an ever-increasing amount of attention. Several States have passed laws attempting to regulate the type of lamp to be used and the nature of the fuel to be burned, and the mining departments of coal-mining States have generally shown a keen and intelligent interest in this subject. The passage of the recent Employers&apos; Liability Act in Pennsylvania has made it necessary for many coal-mining companies to take out liability insurance, and the companies underwriting such insurance have made it desirable for the insured to permit the use of, none but illuminants of established worth. While these conditions have not obtained for a sufficient length of time to permit the statement that the illumination of coal mines by portable lamps has been standardized, still, considerable progress has been made and the direction of future practice in this branch of coal-mining technology is very evident. Under these conditions it seemed that a review of the methods now used in coal-mine illumination, together, with a brief consideration of the principles underlying these methods, might be of some interest. Miners&apos; lamps may be divided into three classes: The open light, the electric cap lamp and the flame safety lamp. It will be desirable to consider each of these classes separately, as each has properties peculiar to itself and one class is hardly comparable with another. In this country, without question, the open light is the most generally used of all miners&apos; lamps. This fact is explained by the relative freedom of a large proportion of our mines from gaseous conditions, and by the admirable systems of ventilation installed in those that show a tendency toward such conditions. In the metal relines, the miner&apos;s candle has had and still has considerable vogue. Because of the small amount of ventilation usually supplied in metal mines, the freedom of the candle from any tendency to produce noxious gases or offensive odors, and the small amount of air it consumes, are. valuable assets, while, because

Jan 2, 1917

By Paul Weir

During the past decade, methods of producing bituminous coal in the state of Illinois, which ranks third in production among the states in which bituminous coal is mined, have undergone great changes. From less than one million tons in 1923, the strip-mine production has gradually increased to a high of 11,725,870 tons in 1937. From a negligible amount prior to 1927, the amount of coal mechanically loaded underground had increased to a high of 28,374,362 tons in 1937. The amount manually loaded in 1937 reached a low of 12,332,023 tons. In this same year, this state ranked first in strip-mine production, also in mechanically loaded production. For this reason a study of the influence of mechanization on location of production in Illinois may be helpful in anticipating what may happen in other producing states. The reason for the changes in methods lies in the differences in costs of production. The Bureau of Research and Statistics of the National Bituminous Coal Commission has made public the following costs of production by various methods in the state of Illinois (district 10) for the last nine months of 1937: all mines, $1.7602 per ton; strip mines, $1.4319; mechanical loading mines, $1.7457; hand loading mines, $2.1793; all underground mines, $1.8703. These are weighted averages for the entire district. Inasmuch as production in 1937 was reported from 58 counties scattered over two-thirds of the area of the state and from five different seams varying in thickness from less than 3 ft. to as much as 12 ft., it is apparent that the location of production must be influenced by the extent of mechanization possible in the various producing counties. SHIFT in Production The term "mechanization" is commonly used to designate the coal-loading operation. However, in a broader sense it embraces the use of any and all mechanical and electrical equipment on the surface and underground. Strip mining is an intensive form of mechanization. The mechanical cleaning of coal is a form of mechanization. Cutting machines and motor haulage likewise are forms of mechanization, hence

Jan 1, 1940

By H. T. Clark, H. K. Work

The instrument for the rapid determination of carbon in steel, described in this paper, was developed originally to facilitate the operation of the pilot-sized open-hearth furnace in the Jones & Laughlin Research and Eevelopment Laboratory. In this small furnace, with its shallow bath, the drop in carbon is accelerated, and a rapid, reliable test for carbon content is indispensable. This problem becomes rather acute when it is desired to finish heats at a carbon content higher than can be estimated with any degree of accuracy by the fracture test. Several independent methods for determining carbon were investigated, therefore, and it was found that a relatively simple magnetic device could be made to give reproducible results. A laboratory instrument was designed and set up for the use of the furnace operators. It was tested exhaustively in the laboratory and was used with considerable success for following the carbon content in the furnace bath. As soon as sufficient data had been compiled to indicate that the instrument might have a wider application, a more rugged model was constructed and placed in the mill to be tested on commercial heats. Finally, about a year ago, instruments were furnished to the plant open-hearth shops, and these have been in use since that time. As a matter of convenience, the instrument has been named the "Carbanalyzer," and will be referred to by this designation in the following pages. $ Eaklier Investigations While by far the greatest number of magnetic investigations in which the carbon content of ferromagnetic materials was considered have had to do with the evaluation of the magnetic properties of steels of known

Jan 1, 1940

By C. G. Brehm

The anthracite-producing region is in the northeastern section of Pennsylvania, and has an area of approximately 484 square miles. It is divided geographically into three separate fields, known as the Northern, Middle and Southern. The Northern field, with Wilkes-Barre approximately at its center, is a basin about 60 miles long and almost 6 miles wide at its greatest distance across. Generally speaking, it may be said that the coal measures in this field lie horizontally, or on slight pitches, and consist of from 11 to 19 veins of coal, varying in thickness from several inches to several feet. The intervening strata between veins may be composed of slate, clay, rock or shale, or a combination of several, and are sometimes very thin. This condition often causes a treacherous roof, therefore roof support and the attending hazard of mining are problems of concern. The Middle field is made up of a number of small basins of not very great depth, and the measures, which are in like number to those of the Northern field, are varying inclinations running from nearly flat to steep pitches. The Lower, or Southern field, is made up of basins of great depth, some being 4000 ft. deep, and its measures are mostly on very steep pitches. In certain sections this Southern field is being mined at an elevation of 1300 ft. below sea level, on a pitch ranging from 50&apos; to practically vertical, and because of the tremendous pressure and the inherent gas in the seams, outbursts of coal frequently occur at the face, locally known as "bumps." These outbursts are accompanied by a rumbling noise, after which gas is usually found. This condition makes mining a difficult and extremely hazardous undertaking, and unusual skill is required on the part of the miner to drive and maintain openings necessary to the production of coal. Miners working in such seams on the heavy pitch must carry face batteries (Fig. 1) to afford proper protection while working at the face, because of the outbursts and free running coal. To drive haulageways or gangways in this field it is

Jan 1, 1940

By R. F. Mehl, M. Gensamer

Creep investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that application of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and structural character of the solid metal. Basis of Investigation Much of the investigation that has been given to the creep characteristics of metals and alloys has been directed toward studying the dependence of creep rate upon stress. Great interest has centered upon the approximately uniform rate of flow that has been demonstrated for numerous metals and alloys. At temperatures above the strain-hardening ranges of materials, this uniform rate frequently is attained after a relatively short period of initial rapid flow, and the period during which it persists determines for most practical purposes the useful life of the

Jan 1, 1938

By R. W. H. Acherson

Blast-furnace flue dust is one of the most troublesome operating factors in the iron and steel industry. It is usually involved in all the unpleasant phases of blast-furnace operations. It adds to our aggravations until we are willing to spend large sums of money to keep it out of our stoves and boilers and more money to handle it again and again on one scheme or another to induce the furnaces to retain it without bad after effects. Several successful operators claim that it is useless to recharge raw flue dust because the furnace would never have blown it out if it had been suitable material for blast-furnace consumption. Most of us who have made persistent efforts to return raw flue dust to the furnaces have decided that it is very often false economy to do so. Yet some remarkable results have been attained at the Ohio Works of the Carnegie Steel Co. through recharging raw dust. The plant comprises six modern blast furnaces. Up to 1909, about 300,000 tons of flue dust had accumulated in stock piles. During the last 10 years, there have been recharged into these furnaces all of the flue dust recovered from the furnace operations, the entire stock pile of Rue dust, and nearly 80,000 tons of dust shipped from other furnaces of the Carnegie Steel Co. The results obtained arc. shown in Table 1.

Jan 1, 1922

Anders Richard Akerman entered the eternal rest on Feb. 23, 1922, after a long and distinguished career. All mining men in Sweden arc mourning him, because he was one of their greatest and a leader in the scientific metallurgy of the iron. He was born April 18, 1837, in Stockholm, where his father, Joachim Akerman, was a professor at the Technical University, but the greater part of his childhood was spent in Falun, where the family moved after his father was made principal of the mining academy. He was at first taught by a tutor, but in 1851 entered the high school in Vesteras and the University of Uppsala in 1855, from which he graduated as a mining engineer on Dec. 11, 1860. A week later, he entered the service of the Department of Commerce and entered the mining academy at Falun, from which he graduated Dec. 15, 1862. The following May, he was accepted as a student in the metallurgical section of "Jernkontoret" (the "Iron Institute") and on Oct. 22, 1864, he was made an assistant in the same section. Thus begun the cooperation with the Iron Institute which was to continue for so many years and to bear such rich fruit. He had, however, previously received two requests from the Iron Institute: One to assist Prof. V. Eggertz in the preliminary work of preparing a handbook on blast-furnace practice, the other to make a complete index of the proceedings of the Iron Institute ("Jernkontorets Annaler") volumes 1817-1864, which index was published in 1866. On Oct. 19, 1865, Akerman was requested by "Jernkontoret" to give during 1866, lectures in the metallurgy of iron at the mining academy of Falun, as Prof. V. Eggertz wished to devote his entire time to the study of assaying. This request was renewed Oct. 15, 1867, for the year 1868, and on April 17, 1869, he was made instructor in metallurgy and mining at the Technical University, to which institution the higher education in mining engineering was transferred at that time. Akerman thus entered his career as a teacher, which lasted until the end of 1891. On May 11, 1877, he was appointed assistant professor in metallurgy and mining; on Sept. 7, 1883, he was appointed acting professor in the same department; and two weeks later was appointed dean of the mining college. On May 21, 1874, he was instructed by the Crown to inspect the mining schools in Filipstad and Falun. As a teacher, Akerman was very popular and his lectures were excellent, in form as well

Jan 1, 1922