Search Documents

By John B. Miles

The present period of depression in the iron industry, with the resultant close approximation of the cost of production to the selling-price of pig-iron, should make the discussion of this subject at this time not only interesting but profitable. It is possible that it may result in the collection of data, which when added to those set forth in this paper will clearly indicate the influence of the rate of driving a blast-furnace upon its fuel-economy. The question is not whether an excessive rate of driving (meaning a rate definitely in excess of the average rate in the United States) results in an increase in the fuel-consumption, but rather whether a rate considerably less than the average does not result in a marked decrease in the fuel-consumption. The commercial and metallurgical sides of this problem must be kept separate. With a large margin between the cost of production and the selling-price of pig-iron, and a plant already in operation, it is frequently profitable to sacrifice a couple of hundred pounds of fuel per ton of pig-iron in order to secure the greater gross profits resulting from a larger tonnage. When this margin decreases with a plant in operation, or when the determination of the size of a new furnace intended for a certain production confronts the management, a clear understanding of the effect of the rate of driving upon fuel-economy becomes necessary. If it be granted that slow driving leads to low fuel-consumption, it should be borne in mind in the design of a new plant for the production of a certain tonnage that the adoption of an economical rate of driving increases only the size of the furnace proper, whereas, due to the decrease in quantity of blast required on account of the decrease in fuel burned, the stoves, the blowing-engines, the boilers and the piping may be de-

Jan 1, 1909

By J. B. Morgan

The mechanical behavior of MgCu2 from 20 o to 725°C has been determined by "brittle-ring" tensite-test techniques, axial compression, and bending experiments. Compressive ductility begins at 450°C (0.65 T/Tm) and slowly increases with increasing temperature white the tensile ductility is characterized by an abrupt brittle-ductile transition at 600°C (0.8T/Tm). The compressive strength increases eightfold from room temperature to 400°C with a "normal" decrease as the temperature is further increased. The tensile strength goes through a rather abrupt threefold increase above 600°C with a subsequent decrease at higher temperatures. The slip system is (111)[110] and the twinning system is (111)[112]. At high temperatures MgCu2 is quite rate-sensitive, and dynamic yield points are observed that are extremely orientation-dependent. The high-temperature creep behavior under constant load is characterized by an increasing strain-rate with time. The general characteristics of the mechanical behavior make it possible to classify MgCu2 with those materials in which initial mobile dislocation density and the dislocation velocity-stress dependence are significant in determining mechanical response. Mgcu2 is the C15 prototype of the cubic Laves phase. Its range of homogeneity extends from 32.8 to 35.5 at. pct Mg at 500°C and narrows at lower temperatures. The lattice parameter is reported to vary from 7.02 to 7.05A,1 and the compound is completely ordered to the melting point of 819°C. MgCu2 has a brassy metallic appearance, is extremely brittle, and many of its physical properties are intermediate between those of the constituent elements: the electrical resistivity is 3.5 x 10-6 ohm-cm, Young's modulus is 10x 106 psi, the shear modulus is 6 x l06 psi, and the thermal coefficient of expansion is 18.7 x 10-6 cm per cm per "C from 20" to 250°C. Usually, properties of intermetallic compounds as functions of temperature have been determined by hardness, compression, or impact behavior, and almost all of these experiments have been performed on polycrystalline materials. Tammann and Dahl,2 for instance, determined the onset of ductility in a series of binary intermetallics by ball-hardness measurements and found the onset to range between 0.71 and 0.96 T/T,. Lowrie's3 investigations included some tensile properties, and he found ductility beginning around 0.65 T/Tm for most materials examined. His work did include some data on polycrystalline, nonstoichiometric MgCu2, however. The present work is an attempt to extend the examination of the particular compound MgCu2 in single-crystal form in order to aid the formation of general concepts about mechanical be-

Jan 1, 1965

By Edmund J. Pryor

DURING the war years restrictions on travel, pressure of work, and the irregular arrival of technical literature from abroad combined to severely isolate Great Britain in a period of intense war expansion of the art and practice of mineral dressing. Many British technicians were fully occupied with the day-to-day problems of improvising substitutes as regular sources of supply failed. and with mastering the strange demands and working conditions of wartime. After a long day spent between ones laboratory and production work, the rest of the waking hours were often filled with fire watching or home guard patrol activities, substituting for a night-shift manager, or "resting" in a dugout while the bombs came down. There was no time for serious study of such technical literature as survived the Atlantic crossing.

Jan 1, 1947

By 000-001-568

August 15th, 1871. THE Institute assembled in Packer Hall of the Lehigh University, the President, Mr. David Thomas, of Catasauqua in the chair. Professor Henry Coppée, President of the Lehigh University, made an address of welcome to the Institute, and placed at its disposal a convenient hall for purposes of meeting. Mr. Thomas tendered his resignation as President of the Institute, as advancing years prevented him from actively participating in its meetings. The Institute declined to accept the resignation, and, on the assurance that active duties would not be expected of him, Mr. Thomas was induced to withdraw it. Invitations were received from Mr. B. C. Webster, President of the Lehigh Zinc Company, to visit the mines and works of the company; from Mr. Charles Brodhead, to visit the Chapman Slate Quarries ; and from the Lehigh Coal and Navigation Company, to visit their works at Summit Hill and Mauch Chunk and the Nesquehoning Tunnel. The Council reported the names of persons already elected in the two classes of members and associates. The following resolutions were passed: Resolved, That a committee of three be appointed, who shall take into consideration the printing and publishing of papers originating with the Institute, and that a uniform system as regards size and execution be adopted. The committee appointed consisted of Messrs. R. W. Raymond, E. B. Coxe, and the Secretary. Resolved, That the Council design and prepare a seal for the Institute at the earliest practicable time. Resolved, That a committee of six, with power to add to its numbers, be appointed to examine into the question of the more economical production of iron in this country. The committee appointed consisted of Messrs. G. W. Maynard,

Jan 1, 1873

By Robert H. Richards

During tile summer of 1870, I had an opportunity to visit the laboratory of the late David Forbes, Esq., in London, and was much interested in a labor-saving device which he had attached to his agate mortar. The mortar was placed in the centre of a small table, and about ten inches to the right of the mortar, a post, perhaps two

Jan 1, 1879

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS t ARE ASSOCIATES THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY THE FIGURES AT THE END OE THE ADDRESS INDICATE THE YEAR OE ELECTION HEAVY FACED T1 PE SIGNIFIES HONORARY MEMBERSHIP *ABADIE, EMILE R , Min Engr P 0 Box 83, Berkeley, Cal '76 *ABBE, CLEVELAND, JR, Geol Aid, U S Geological Survey, Washington, D C '00 *ABBOTT, AI ARTHUR, Cerro de Pasco Mining CO , Cerro de Pasco, Peru, So America '95 *ABBOTT, ARTHUR V , Electrical Engr , Westinghouse, Church, Kerr & Co , 8 Bridge St, New York, N Y '82 *ABBOTT, CLARENCE E, Chief Min Engr, Care Fayal Mine, Eveleth, Minn '04 *ABBOTT, JAMES W , Min Engr , Special Agent, Rocky Mountain and Pa¬cific Coast Division, U S Dept of Agriculture, "Tile New Markham," Denver, Colo '94

Jan 1, 1910

By Paul F. Kerr

Uranium mineralization occurs in the footwall of the Sunshine vein from the 2900 to the 3700 level. Veinlets of uraninite associated with pyrite and jasper have been so extensively divided and recemented that units more than a few feet in length are seldom observed. The wall rock is St. Regis quartzite of the Belt series. The age of the uraninite, on the basis of isotopic analyses, is 750 t- 50, which agrees with geological data suggesting that phases of the Sunshine mineralization are pre-Cambrian.

Jan 5, 1953

By L. J. Klinkenberg

It is pointed out that the current concept of pore size distribution is not unequivocally defined and that different methods aiming at a determination of such a distribution therefore do not lead to the same results. A pore size distribution should not be based on the idea that a core should, under all circumstances, behave as a bundle of straight non-interconnected capillaries of the same pore size distribution. This is illustrated by calculations and experiments on the displacement of miscible liquids. INTRODUCTION The introduction of the concept of pore size distribution has been an attempt to characterize the intricate geometry of the flow channels in porous media. As pores in a porous medium are interconnected it is impossible to describe exactly what is meant by a "pore" and, therefore, the term pore size distribution requires further amplification. In the visual method for the determination of pore size distribution "the pore" is considered to be the hole between the grains as observed on thin sections or on a polished surface of the rock under a microscope. In all other presently known methods,1,2 a displacement process is studied and it is ascertained what as- semblaae of straight cylindrical capillaries would show the same behavior. The distribution of the capillary diameters of this assemblage is said to represent the size distribution of the pores of the actual porous medium. From the foregoing it is already apparent that it is useless to try to decide which process or which method of investigation leads to a "correct" pore size distribution. To illustrate this further a displacement process in which a fluid is displaced by another miscible with it will be discussed and the results will be interpreted in terms of a pore size distribution. DISPLACEMENT EXPERIMENTS WITH MISCIBLE LIQUIDS OF NEARLY IDENTICAL VISCOSITY AND DENSITY Interpretation in the Form of a Pore Size Distribution If distilled water is displaced from a homogeneous unconsolidated sand pack by, for instance, a dilute solution of NaCI, the breakthrough recovery i.e., the amount of distilled water produced at the moment the first trace of NaCl can be detected in the effluent water, is between 95 and 100 per cent of the pore volume of the pack. This result can be understood by following in imagination the course of one particle of the liquid. Imagine a length, ?l, at the end of which a liquid particle has an independent chance of a renewed choice of pores of different diameters. In other words, the particle has a choice of traveling time, at, for any length ?l; instead

Jan 1, 1958

Charles Catlett, Staunton, Virginia (communication to the Secretary*): I have had occasion to examine a few of the irondeposits in the immediate section of which Mr. Watson speaks, but have not had an opportunity to visit any of the well-known manganese-deposits. I find the former can be very safely read in light of the information which it is possible to get from the same measnres farther. north, where they are less completely decomposed. In the same way all of his conclusions in regard to the geology of the manganese-deposits bear out their occurrence in Virginia, when we allow for the far more complete decomposition in the section he has so carefully studied. Judging from the same measures farther north, I think he will be safe in agreeing even further with Penrose as to the origin of these ores. Some years ago I carried on prospecting work in these measures in Virginia, in which the iron-ore and manganese-ore were followed down to undecomposed material, and in which their occurrence along a definite line of stratification, and apparently a part of the original bedding, was plainly shown. This is unusual, however, even in the section of which I speak. At Crimora, Virginia, the decomposition is quite complete; at the same time the results of some hydraulic work, which has been done there, disclosed, at the time of my last visit, the manganese interbedded in the residual clay along a definite and distinct plane parallel to the bedding of the underlying quartzite, and which, as is shown at other points, corresponds with the plane of the original material. In view of the phosphorus reported by Mr. Watson as existing in the Cartersville ores, and the not uncommonly prohibitive amount in southern ores, I am interested to know whether

Jan 1, 1904

NEW MEMBERS The following list comprises the names of those persons who became. members during the period Sept. 10, 1918, to Oct. 10, 1918. ADDISON, HERBERT, Vice-pres. and Mgr., Big Horn Collieries Co., 412 Colorado Bldg., Denver, Colo. ALLAN, .ANDREW, JR A. Allan & Son, Harrison, N. J. AMI, HENRY M., Charge of War Metals and Minerals, British Embassy, Washington, D. C. ALTHAR, HOMER C., Mill. Engr., The Lorain Coal & Dock Co., Bridgeport, Belmont Co., Ohio. BASER, JOHN T Pres., J. T. Baker Chemical Co., Phillipsburg, N. J. BARBA, W. P., Lieut. Colonel, Ordnance, U. S. A., 2301 Connecticut Ave., Washington, D. C. BENSON, JOHN PATS Min. Engr., Aurora Cons. Mines Co., Aurora, Nev., BOSWELL, H. F Resident Inspector, Southern Railway System, St. Louis, Mo. BRAUCHER, PETERS., Foundry Mgr., Philadelphia & Reading Ry. Co., Sixth & Perry St., Reading, Pa.

Jan 11, 1918

By Haydn H. Murray, Sam H. Patterson

The term "clay" is somewhat ambiguous un¬less specifically defined, because it is used in three ways: (1) as a diverse group of fine-¬grained minerals, (2) as a rock term, and (3) as a particle-size term. Actually, most persons using the term "clay" realize that it has several meanings, and in most instances they define it. As a rock term, clay is difficult to define be¬cause of the wide variety of materials that com¬pose it; therefore, the definition must be gen¬eral. Clay is a natural earthy, fine-grained ma¬terial composed largely of a group of crystalline minerals known as the clay minerals. These minerals are hydrous silicates composed mainly of silica, alumina, and water. Several of these minerals also contain appreciable quantities of iron, alkalies, and alkaline earths. Many defini¬tions state that a clay is plastic when wet. Most clay materials do have this property, but some clays are not plastic; for example, halloysite and flint clay. As a particle-size term, clay is used for the category that includes the smallest particles. The maximum-size particles in the clay-size grade are defined differently on various grade scales, Soil investigators and mineralogists gen¬erally use 2 micrometers as the maximum size, whereas the widely used scale by Wentworth (1922) defines clay as material finer than ap¬proximately 4 micrometers. Some authorities find it convenient to use the term "clay" for any fine-grained, natural, earthy, argillaceous material (Grim, 1968). When used this way, the term includes clay, shale, or ar¬gillite, and some argillaceous soils. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, the term is generally un¬derstood by those who use it. Clay is an abun¬dant natural raw material, and it has an amaz¬ing variety of uses and properties which will be discussed in this chapter. Clays rank among the leading industrial min¬erals in both tonnages produced and total value. Their importance is indicated in Table 1, which lists the 1970, 1971, and 1972 production and values according to the U.S. Bureau of Mines (Ampian, 1972). Adequate reliable statistical data on which to summarize world production of clay are un¬available; this paragraph outlines the world re¬quirements for clay only in a very general way. According to one estimate, the world bentonite production in 1972 was 3.5 million tons (Anon., 1973a), but in the authors' opinion it was prob¬ably at least 5 million tons. The total fuller's earth produced was at least 1.5 million tons and may have been as much as 2 million tons. The total world kaolin production in 1972 was more than 10 million tons. Approximately 7 million tons of this total was produced in only two regions-the Georgia-South Carolina kaolin belt in the United States and the Cornwall re¬gion, United Kingdom. The world's 1972 out¬put of ball clay, which is also produced pri¬marily in the United States and the United Kingdom, was approximately 1.5 million tons or perhaps a little more. The total world fire clay production in 1972 was probably about one and one-half to two times and the miscellaneous clay production three times the United States production. As industrial minerals, clays are a complex group that consists of several mineral commodi¬ties, each having somewhat different mineral¬ogy, geologic occurrence, technology, and uses. In this chapter these commodities are organized

Jan 1, 1975

By Paul M. Tyler

ROUGHLY one-half the value of mineral products at mines or quarries must be spent for wages. In view of the steady increase in hourly wages that continued for several decades prior to the onslaught of the recent depression, it is perhaps surprising to discover that labor's share of the gross proceeds of the mining and quarrying industries of the United States declined to 46.8 per cent in 1929, compared with 52.2 per cent in 1919 and 53.2 per cent in 1909. The actual percentages vary in different branches of the industry and in different localities but the downward trend is unmistakable. For the period 1909 to 1919 it was quite marked in every industry and from 1919 to 1929 it was apparent in all but six: namely, gold and silver lode mining, placer gold mining, crude gypsum production, marble quarrying, asbestos production, and fluorspar Tninino mining

Jan 1, 1933

By Robert Glass Cleland

IN gathering material for this book, I have made extensive use of the archives of Phelps Dodge, contemporary news- papers, and a wide range of secondary sources. Two manuscripts-one on the history of Phelps Dodge by Arthur Train, Jr., and John L. Lawler, the other a biography of William E. Dodge by Richard Lowitt-have been of the greatest value. I owe a particular debt to the authors whose names I have just mentioned. I have also gathered important information and obtained revealing points of view from conversations with many people. Personal visits to the company's mines and plants added knowledge and understanding that nothing else was able to supply. I am greatly obligated to the officers of the company, especially to Mr. Louis S. Cates, chairman of the board of directors, Mr. Robert G. Page, president, Mr. George R. Drysdale, vice-president of Phelps Dodge Corporation, and Mr. Walter C. Bennett, president of Phelps Dodge Refining Corporation, for their co-operation and assistance. Mr. Wylie Brown, former president of Phelps Dodge Copper Products Corporation, also supplied valuable data and deeply appreciated hospitality. In my visits to the Phelps Dodge properties, company representatives extended every hospitality and placed at

Jan 1, 1952

By E. C. Winegartner, A. A. Ubbens

The company attempting to sell coal to large utility plants is faced with a confusing array of quality parameters and specifications which are often poorly understood by both the utility company and coal supplier. While these specifications are placed on the coal by the utility company, many of them originate with the boiler manufacturer who must guarantee that his product will perform satisfactorily on the design coal. A proper understanding of these parameters by both the coal supplier and utility company can lead to a better understanding of their mutual problem. This paper brings together most of the parameters in common use today and attempts to show what the parameters mean to the boiler designer, particularly in the area of boiler slagging and fouling.

Jan 1, 1977

By W. E. C. Eustis

During the last year I had occasion, on behalf of our New York copper works, to send to various chemists samples, intended to he accurate, of material which we were buying and selling, and I was astonished to find what differences were reported. After talking over the probable reasons for this with a number of chemists and metallurgists, it was suggested that it would be of real use and some scientific interest to send samples to the different chemists, and take such care in making up the samples that we could feel sure that each chemist had as nearly identical a sample as it was possible to make. After some consideration it was determined to send a mixture which should carry about 50 per cent. copper, and

Jan 1, 1883

By Archer E., Wheeler

Producing copper companies were active during 1941 owing to the national defense program the United States and the requirements of the friendly belligerent nation. This activity extended to the American owned properties in South America, the major part of whose product was taken by the Metals Reserve Co., a U.S. Government agency. Anaconda Copper Mining Co. is building a new converter plant at Anaconda, with four units of the Peirce-Smith type. The addition is being built adjacent to the reverberatory plant so as to avoid the necessity of hauling matte and slag. It is expected to be completed this year.

Jan 1, 1942

By W. G. Frailing, W. P. Sims

The Lakeview Pool of Kern County, California, was discovered in 1910 with the drilling of Lakeview No. 1 which blew out and produced an estimated 8,250,000 bbl of oil in 544 days of uncontrolled flow. The well has since been known as the Lakeview Gusher. Full exploitation of the pool did not take place until about 25 years later. A total of 112 producing wells were completed in the Lakeview sand through April 30, 1949. As of that date, about 30 per cent of the total wells drilled were still producing, with an average pool production rate of approximately 2000 bbl per day. The cumulative oil production was about 41 million bbl of oil, or 55.3 per cent of the tank oil originally in place. The pool is bordered on its down-structure side by a body of inactive edgewater and water production where present has been principally the result of coning. Since the depletion of the greater portion of the gas energy by the Lake-view Gusher, the pool has operated under gravity drive. Relatively high angle dips, good permeabilities and favorable fluid characteristics have made gravity drainage particularly effective. Since January, 1942, the oil recovery -has been relatively constant at about 53,000 bbl per ft drop in fluid level. Correlations between the volume of reservoir space drained and the cumulative oil produced indicate that an ultimate recovery of 63.3 per cent of the tank oil originally in place is attainable. INTRODUCTION The Lakeview Pool is an outstanding example of gravity drainage. It is one of many productive reservoirs of the Midway-Sunset Field, and is located in Kern County, approximately five miles southeast of Taft and two miles north of Maricopa, California. Its position rel- ative to surrounding pools and to the Thirty-Five anticline is shown on Fig. 1. The northern portion of the pool lies in sections 32 and 33, Township 32 South, Range 24 East, Mt. Diablo Base and Meridian, while the southern portion lies in sections 25, 26, 35 and 36, Township 12 North, Range 24 West, San Bernardino Base and Meridian. As no two sections bear the same number, they will hereafter be referred to by section number alone. The purpose of this paper is to review the performance of the Lakeview Pool in an effort to evaluate the effectiveness of gravity drive as a recovery mechanism. REGIONAL STRATIGRAPHY AND STRUCTURE The oustanding structural feature is this area is the Thirty-Five anticline, the axis of which plunges South 75" East through the center of Section 35. As shown on Fig. 2, the following zones are oil and gas bearing in the Thirty-Five anticline area: Pleistocene Basal Tulare Tar Sands Pliocene San Joaquin Mya Sands Top Oil or Scalez Zone Etchegoin Kinsey Sand Wilhelm Zone Gusher Sand Calitroleum Sand Miocene Reef Ridge Lakeview Sand Sub-Lakeview Miocene Sands Monarch Sands or fractured shale equivalent Maricopa Webster Sand or fractured shale equivalent Fractured Shale-Uvigerina Zone C Obispo Sand and fractured shale equivalent Pacific Shale Zone The productive interval of the Lakeview Pool is limited to Upper Miocene and Lower Pliocene deposition. In this general area, the most prevalent type of accumulation results from stratigraphic traps or permeability pinchouts. As is the case of the Lakeview Pool, strati-graphic traps resulting from angular unconformities are present. The structure within the Miocene does not parallel that of the Etchegoin (Pliocene), as the Miocene beds were folded, and in places faulted, and subjected to erosion prior to Pliocene deposition. The Lakeview horizon consists of truncated sands which occur on the northeast flank of the Thirty-Five anticline. The direction of strike is west and northwesterly through sections 25 and 36 and continues northwesterly through sections 26 and 33, to the approximate center of section 32. At this point the strike swings to the northeast and the horizon re-enters section 33. in the northwest corner. The change in strike in section 32 affords synclinal accumulation at that point. The Lake-view sand is truncated updip by the Etchegoin overlap. To the southeast, the sand shales out, while to the northwest, the productive interval appears to be limited by a combination of stratigraphic pinchout and permeability barrier. Structurally, the Lakeview reservoir presents three areas of interest, as shown on Fig. 3. Area I in section 32 is a region in which a productive Sub-Lakeview Miocene sand is present. It occurs from 10 feet to 30 feet below the base of the Lakeview sand and attains a maximum thickness of 25 feet in Well No. 21, section 32. The producing characteristics of the Sub-Lakeview Miocene sand differ radically from those of the Lakeview sand. Water production at high structural locations and abnormally high fluid levels indicate that there was no communication with the Lakeview sand. Wells in Area I penetrated this sand and produced it in conjunction with the Lakeview sand. In Area 11, the Lakeview sand is a

Jan 1, 1950

By GEORGE D. RAMSAY

WHEN the Ironton blast furnace of the Columbia Steel , Co. was first put into operation the iron ore was mined frol11 the deposit near Iron Springs, Utah. This is principally a hematite with 12 to 20 per cent of magnetite finely disseminated throughout the ore. It varies from a fairly soft broken rock structure to that which is hard and compact. In the broken form it will weigh about 150 lb. per cu. ft., and in place the density is approximately 250 lb. per cu. ft. The first ore received for the blast furnace was crushed so as to pass through approximately a 4-in. square opening screen. A typical screen test of this ore is shown in Table 1.

Jan 1, 1935

By John B. Hastings

TEN miles from Hartsel, near Antelope springs, in Park county, Colorado, there is a large area of unconsolidated lake beds, which are interesting because at least a part of the lacustrine sands contains in the aggregate an immense amount of gold. During 1906, one of the arms of this dessicated lake was fairly well prospected with shafts and cuts by an Eastern company to test its value, as favorable amounts of gold had in some instances been found upon it. The claims of the company contain about 5,000 acres of the beds; but this is only a small portion of them, a south branch from a main body, which is at least 7 miles in diameter, with other and very wide lateral gulches, paralleling the one herein described on the east and west. A certain amount of digging and sampling was done in the outside areas; but the result was evidently unsatisfactory, since the work was discontinued. his section of Colorado has not been studied geologically, and the age of the ancient lake is unknown. It is probably Quaternary. I spent two weeks on the ground, in September and October, 1906, but was quite absorbed in the sampling. I looked, however, for terraces on the rim-rock and other evidences of movement and erosion, but did not find anything to denote an earlier age than the Quaternary. The granite rim-rock may be Archean; S. F. Emmons says that some of the granites in central Colorado are as old as that. The rim-rock as observed is a gray quartzose biotite-granite, except a small area in Sections 3 and 34, where it is a felsitic (?) breccia. The breccia is silicified by solfataric action at the corner near Shaft No. 7, in Section 34; but this action is older than the sands and does not extend to them. The shaft averaged 50c. per ton, more than twice as much as the rest.

Jan 5, 1908

By Paul Tyler

FULLY a decade ago, demand for ground mica began to exceed supplies of scrap mica from manufacturing operations and of waste block from feldspar and sheet mica mining in the United States, with the result that in recent years the market has absorbed larger and larger quantities of mica recovered as a by-product from clay washing,1 as a joint product with kyanite,2 and by grinding schists. So far, only schists that contain a large percentage of mica have been utilized for making ground mica, but already there has been a good deal of wishful thinking with regard to recovering mica as an aid to the prospective working of low-grade gold ores and ores of certain base metals. With wet-ground mica selling at $60 to $100 a ton and even dry-ground mica worth over $20 a ton, many ores that could not be considered as otherwise workable under present conditions will show commercial possibilities if they can be made to yield even a relatively small percentage of salable mica. An interesting paper might be written on the coming role of industrial minerals as joint products of metal mines, It is largely a matter of mar-kets. Many years ago I watched the mess left behind the gold dredges in the mountains of Colorado and thought of the Denver sand and gravel operators who prided themselves upon their canniness in providing devices for catching gold merely as an incident to their regular business of selling what we miners classed as "tailings." Nowadays almost every milling or mining operation near settled communities finds use for at least part of its waste for road material or concrete aggregate and several eastern iron mines have gone into the crushed-stone business. Promoters now mention fertilizer "filler" as potentially salable at all the way from $1 to $10 a ton, or whatever is needed to cover costs of mining and treating the "ore" and leave the metal values as "clear profit." In emulating the pork packers in their efforts to utilize "everything but the squeal,"

Jan 1, 1938