Search Documents

By Max Hebgen

I. Natural Features of State Affecting Power Development .. 792 II. Early Developments. 1. Big Hole Plant................. 792 2. Canyon Feny Plant............... 793 3. Madison Plant No. 1............... 593 4. Black Eagle Plant................ 795 III. Later Developments. 1. Madison River System .............. 795 2. Missouri River System.............. 797 3. Great Falls System............... 797 4. Missoula River Development............ 797 5. Big Fork Development.............. 802 $ IV. Present Capacity of Power Developments....... 802 V. Transmission System...............: . 802 VI. Character of Load. 1. Lighting and Small Power Uses........... 804 2. Street Railways ................ 804 3. Mining................... 804 4. Railroads.................... 808 5. Irrigation................... 810 VII. Operation of System................. 812 VIII. Increase in Use of Power............... 811 IX. New Power Developments............... 814 X. Undeveloped Powers................. 815 It is estimated that the total stationary power now used in the United States. steam. water and gas. is probably over 30.000.000 h. p. The total developed water power is about 6.000.000 h. p. The water power in the United States now economically capable of development probably exceeds 25.000.000 h. p. The total developed and undeveloped power is

Jan 1, 1914

By William N. Poundstone

What attracts young engineering graduates into the coal industry? What do these young men expect of a career in coal mining? These questions are often asked and debated by mining men throughout the country. In order to present a comprehensive answer to them, an opinion survey was conducted at West Virginia University's School of Mines among the junior and senior classes and part of the sophomore class. The tabulation of the answers showed that the present-day mining engineering student is an older, more mature individual as compared with former years and as compared with other present-day college students. The average age of the country's record-breaking 150,000 college graduates is 24 years. Among this year's mining graduates at West Virginia University, 78% are of this age or older. Over half (54%) of those polled in the survey are married. This is com- pared to 30% as a national figure. Of those married, 38% have one child and over 6% have two children. The entire senior group covered by this survey has averaged almost three years in the armed forces. An article entitled "The Class of '49" in the June issue of Fortune magazine states that this year's class is the oldest, most mature class in history. Our survey indicates that the mining engineering students at West Virginia University are well above the average in this respect.

Jan 1, 1949

By Herluf P. Nielsen, Robert I. Jaffee

IN recent years much attention has been given to high-melting alloy systems, It has been of interest in this respect to investigate the alloys of platinum and tungsten, which were known from the literature to have very high melting points up to about 50 pct tungsten, but about which little had been published on the high-tungsten side of the system. Powder metallurgical methods were used throughout this investigation for the preparation of the alloys, utilizing electrical sintering techniques such as are used for tungsten and molybdenum. In the course of the work it was found desirable to determine fusion temperatures of the alloys, and it was possible from these and other data to draw a tentative constitutional diagram (solidus, mostly) applicable to the high-temperature part of the system. No attempt was made to determine solid solubility vs. temperature data, nor to investigate the lower temperature transformations in the solid state. Data on the microstructure, hardness, and a note on oxidation resistance of the sintered alloys were obtained. PAST WORK Müller1 determined liquidus temperatures of platinum-rich alloys to 50 pct tungsten, using a radiation method employing a photoelectric cell, and found that the melting points increased progressively from 1771°C for platinum to 2350°C for the 50 pct alloy. Microscopic evidence by Müller that complete solid solutions exist to 50 pct tungsten was not checked by Kremer2 who, according to Vines and Wise,3 found that "although the 8 pct tungsten alloy was a solid solution, the 26 pct tungsten alloy contained a eutectic or an intermediate phase." Hultgren and jaffee4 using X ray methods found continuous solid solutions to at least 33.6 pct tungsten (35 at. pct) after annealing in vacuum for 6 days at 1000°C. Vines and Wise3 report work communicated to them by E. C. Rhodes on wrought alloys to 7 pct tungsten, which showed that tungsten hardened platinum extremely rapidly, and was one of the most potent hardeners of the binary additions to platinum. Considerable quantities of 4 pct tungsten platinum wire have been produced for grids in radar tubes and for aircraft spark plugs. Some of the alloy for the latter application is made by sintering, the remainder by smelting and casting. MATERIALS The platinum powder used in this work was kindly supplied by the research and Development Laboratory of the Owens-Corning Fiberglas Corp., Newark, Ohio, It was prepared from scrap platinum. After dissolving in aqua regia and evaporating almost to dryness, the solution was worked up several times with concentrated HCI. the resultant platinic chloride was diluted considerably, and metallic zinc was added, which precipitated the platinum in a very finely divided form. After dissolving the

Jan 1, 1948

Jan 1, 1968

By PAUL DYER MERICA

PAUL DYER MERICA, who has been awarded the James Douglas Gold Medal for his achievements in non-ferrous metallurgy, is a Hoosier, having been born at Warsaw, Ind., in 1889. His father, a clergyman and educator, was president of the University of Wyoming from 1908 to 1913. After graduating from the University of Wisconsin in 1908, young Merica (not yet twenty years of age) went to China, where he was professor of chemistry in Chekiang Provincial College, Hangchow, until 1911. He then went to Germany to s t u d y and was fortunate enough to receive his Ph.D. from the University of Berlin just a few months before the outbreak of the World War in 1914. Returning to America, his first position was as special investigator at the En¬gineering Experiment Station of the University of Illinois, but before the year was out he joined the staff of the U. S. Bureau of Standards as associate physicist. Since 1918, he has been superintendent of research for the International Nickel Co. His work during those years is excellently summarized in the following quotation from the statement of Zay Jeffries recommending him for the award.

Jan 1, 1929

By Donald A. Brobst

The minerals barite (BaSO4-barium sulfate) and witherite (BaCO3-barium carbonate) are the chief commercial sources of the element barium and its compounds whose many uses are nearly hidden among the technical complexities of modern industrial processes and products. Barite, the major ore mineral, is extremely vital to the petroleum industry which in 1980 consumed at least 90% of the world's production of 8.8 million tons as a major ingredient of the heavy fluid, called mud, that is circulated in rotary drilling of oil and gas wells. The remaining 10% of the barite production was consumed chiefly in the manufacture of barium chemicals and glass and as a pigment, filler, and extender. Barite occurs throughout much of the world and is available from three major geologic types of deposits-vein and cavity filling, residual, and bedded-in sufficient quantity at competitive prices to meet current demands. The world's demand for barite is expected to increase, and geologic circumstances are favorable for the discovery of new deposits of commercial value. Witherite is much less common and abundant than barite, although it is more desirable in many ways as a raw material for the production of barium chemicals. The United States has not produced witherite since about 1950; England is currently the chief producer of witherite. End Uses Most of the world's barite production since 1926 has been used as a weighting agent for the muds circulated in rotary drilling of oil and gas wells. The muds fundamentally are mixtures of water, clay, and barite in different proportions that vary according to local reservoir conditions. Muds with a specific gravity as great as 2.5 are used. The mud is pumped down the hollow drill stem, passes through the bit at the bottom of the hole, and rises to the surface in the space between the drill stem and the wall of the hole. In the course of this circulation the drill bit is cooled, cuttings are removed, the drill stem is lubricated, the walls of the hole are sealed, and the hydrostatic head of the column of weighted fluid helps to confine high oil and gas pressures. The latter feature aids in prevention of gushers, thus reducing both environmental pollution and waste of oil and gas resources as well as conserving the natural reservoir pressure for greater production and rate of recovery of the products contained in the rocks. Barite is particularly well suited for drilling mud because it is clean, easy to handle, soft (nonabrasive), heavy, virtually inert chemically, and relatively inexpensive compared to many other available heavy materials. Barite is used in the manufacture of glass in continuous tanks. The addition of barite homogenizes the melt and gives greater brilliance and clarity to the finished glass. Ground barite, both unbleached and bleached by sulfuric acid, is a common industrial filler, extender, and weighting agent. The rubber industry is a major consumer of barite as a filler. Barite also is added to bristolboard, heavy printing paper, playing cards, rope finishes, brake linings, clutch facings, plastics, and linoleum, to name but a few uses. Bleached barite has long been an extender in white lead paint because of its weight. The low index of refraction of barite, however, makes its ability to cover marks poorer than some other substances, but its low capacity for absorption of oil is a good feature. Off-color or unbleached barite can be used as a filler in colored paints. In the construction industry, some lump barite is used in concrete aggregate to weigh down pipelines buried in marshy areas and to shield nuclear reactors. Because barite absorbs gamma radiation well, its use reduces the amount of expensive lead shielding otherwise

Jan 1, 1983

By William H. Bassett, C. J. Snyder

Cable sheaths made from common lead have been used to protect underground cables since the beginning of the power-cable industry. Only within the last few years, however, has a systematic study of the production methods and of the causes of failures in cable sheathing been undertaken. Recent increases in the use and demands for service made upon power cables have emphasized the importance of high-quality cable sheaths. It was customary for the users to attribute the cause for their sheath failures to the lack of purity of the lead, but this contention has not been borne out by field and laboratory inspection of the sheaths. During the past two years the writers have had an opportunity to examine various types of sheaths that were removed from power cables after failure. These samples were obtained from various parts of the country and represent, it is supposed, the production of the principal cable manufacturers. Aside from corrosion, the common field difficulties can be classified either as mechanical or structural, as outlined below, and when structural irregularities are found they can all be attributed to manufacturing causes and in no way reflect the purity of the lead. Clasxification of Cable Sheath Failures Other Than Corrosive Mechanical Irregularities A. Splits caused by excessive internal pressure B. Injuries such as nail holes, cuts, tsars, etc. C. Intercrystalline cracks caused by vibration Structural Irregularities A. Splits C. Voids in wall of sheath a. Caused by imperfect welds a. Blisters 13. Holes through sheath b. Laminations a. Caused by yellow oxide inclu- D. Questionable structures sions in sheath wall a. Prominent flow lines b. Blowouts by entrapped gases b. Large areas filled with suboxide during manufacture c. Scattered yellow oxide or dirt C. Caused by inclusions of dirt and

Jan 1, 1933

By R. P. Abendroth

This study is concerned with the kinetics of selective oxidation of chromium in a commercial Fe-Cr-Ni alloy. Selective oxidation of chromium in this alloy, by use of a low oxygen-potential atmosphere, leads to the formation of a compact, protective layer of Cr2O3. This layer serves to protect this alloy from gross scaling when it is subsequently exposed to severe oxidizing conditions at high temperature. The interaction of low oxygen-potential atmospheres close to equilibrium with Fe-Cr and Ni-Cr alloys has been studied by others."' These studies werk concerned with the surface-structure variations under slightly oxidizing conditions. NO detailed study was made of the oxide scale formation kinetics, however. The alloy samples were cut from 0.012-in.-thick sheet, with an apparent surface area of 7.1 sq cm. These sheet samples were abraded through 4/0 metallographic paper, and washed in alcohol and acetone. The analysis of the sheet alloy is (in weight percent): 42 pct Ni, 5.5 pct Cr, 0.09 pct C, 0.18 pct Al, 0.36 pct Si, 0.26 pct Mn, balance Fe. The weight gain vs time data were obtained with a 2-g capacity fused-silica spring—cathetometer system. The spring deflection was optically magnified ten times before being read by the cathetometer. A sensitivity of about 0.01 mg was attainable. The spring was enclosed in a water jacket maintained at 60°C to minimize the effect of temperature changes. The sample was suspended from the spring with a fused-silica hangdown and was positioned in the thermal center of a mullite furnace tube. Sample temperature was read with the aid of a thermocouple placed outside the mullite tube and an inside vs outside temperature calibration. Temperature change during the course of a run was ±0.25°C, with a temperature gradient of less than l.O°C over the length of the sample. Total temperature uncertainty was no more than ±3.0°C. Alignment difficulties between the hangdown and radiation shields in the furnace tube required that the sample be positioned in the furnace when cold, and heated with the furnace until the temperature stabilized at the desired point. This required 5 to 6 hr, and was carried out in Matheson ultrahigh-purity hydrogen. Oxidation was started, after evacuation, by introducing a hydrogen-water vapor mixture, obtained by saturating hydrogen with water vapor at 31.00o ± 0.02oC. Oxidation was continued for 90 min. Gas flow was 300 ml per min during heat up and oxidation. Since only several milligrams of oxide are formed on each sample, chemical analysis of the oxide is difficult. A representative analysis is: 80 pct Cr2O3, 5 pct Fe2O3, 3 pct Al2O3, 4 pct MnO, 7 pct SiO2, 1 pct or less NiO. X-ray diffraction analysis of the oxide as formed on the alloy gives rhombohedra1 Cr2O3, and barely distinguishable amounts of a cubic spinel phase, and possibly AlZOs and SO2. The identification of these latter two compounds is by no means certain. The spinel phase could be based on iron or manganese as these elements are present in significant amounts in the oxide. The results of the kinetic studies using 31°C dew-point hydrogen-water vapor mixtures were found to conform to a parabolic rate law. In many cases the parabolic plot consisted of two intersecting straight lines, defining an early and a late rate for a particular run, and in the other cases the parabolic plot consisted of one straight line for the entire run. The slopes of the various straight lines were determined by the method of least squares. Reproducibility of the data was good enough for multiple runs at the same temperature such that the value given for the rate constant is the average for two or more closely similar values, rather than widely varying values of the rate, where more than one determination is indicated in Table I. The exhibition of only one or of two rate constants during a run can happen at the same temperature. Thus, Table I shows that at 11'74°C a single rate constant was obtained from one sample, while other samples oxidized at the same temperature gave an early and a late rate constant. It should be noted that the single rate constant corresponds very closely with the early rate constant. This is also true at 1153°C. The time at which the late rate started to appear was variable, usually occurring 20 to 40 min after oxidation had started.

Jan 1, 1964

By E. A. Gulbransen, W. S. Wysong

The behavior of molybdenum and its surface oxides in oxidizing and reducing gas atmospheres and in high vacua at elevated temperatures is a question of scientific and technical importance. The use of molybdenum as a metal or as an important component in alloys in oxidizing atmospheres at elevated temperatures has been limited because of the unprotec-tive nature of its oxide film and the volatility of this oxide at moderate temperatures. This communication will present results of a vacuum microbalance studyl, 2 of the following problems: (I) the oxidation kinetics in the temperature range of 250°to 450°C; (2) the reduction with pure hydrogen of thin oxide films formed on molybdenum; (3) the volatility of the thin oxide films; and (4) the vacuum oxidation of molybdenum at high temperatures. Molybdenum is an interesting metal to study for the following reasons: (I) although the oxide-to-metal-volume ratio is greater than one, the metal is not considered protective; (2) the metal oxidizes readily at temperatures of 2 50°C and higher; (3) the oxides of the metal are reduced at temperatures as low as 500°C by pure hydrogen; (4) the oxide Moo3 melts at 795°C; and (5) the oxides of molybdenum are volatile at moderate temperatures. The following variables are studied in the oxidation kinetics: time, temperature, pressure, surface preparation, surface area, concentration of inert gas in the lattice, cycling procedures in temperature, vacuum effect and high temperature vacuum oxidation. The general interpretation of many of these factors has been previously discussed. Literature The oxidation of molybdenum has not been studied critically. Although many studies have probably been made on the kinetics of the oxidation process, none has been reported in the literature available to us. The crystal structures found in the oxidation of molybdenum have been studied by Hickman and Gulbransen." Their results showed that Moo2 is the oxide which is stable in contact with the metallic substrate throughout the temperature range 300 to 700°C. As the film thickens in the low temperature range, MoO3 becomes predominant on the surface. Above 400°C, Moos is no longer observed, MoO2 being the only oxide found. Hagg and Magneli6 have shown from an X ray study that the a-phase, orthor-hombic Moo3 is stable up to 1050°C. Two other phases, ß and ß with compositions close to MoO2.90 are also obtained. The formula for the 0 phase is not given but that of the ß phase is defined as Mo9O26 The 0' phase is found to be built upon a monoclinic unit cell. A ?-phase is isolated from a preparation MoO2.75 heated for 17 hrs at 670°C. This phase is

Jan 1, 1949

By Robert L. Akre

When Marco Polo visited China in the 13th century, no one knew what black powder was except the Chinese: they knew enough to make dazzling fireworks with it. But the realization that black powder could also do useful work came much later and, like all important discoveries, it altered the course of history. It was in the 14th century that black powder was first used to break rock in a very crude way: there were no drills and the powder was simply poured into cracks and exploded by setting it afire. Because its energy value was pretty low, the need for something more powerful was felt when the industrial revolution arrived.

Jan 6, 1976

By Thomas Robins

About six years ago the writer had occasion to visit a large magnetic iron-ore concentrating-plant, and then saw for the first time rubber belts employed for conveying-purposes. These belts were from 20 inches to 30 inches in width, and some of them were as long as 500 feet between centers. When I spoke of the enormous amount of material they handled with a small expenditure of power, the superintendent assented, but at the same time complained that although he bought the best quality of belts, the abrasion of the ore wore them out very rapidly, causing continually very large bills for repairs and renewals. On close examination several interesting points were discovered :

Jan 1, 1897

YEAR OF ELECTION 1913. FRANK DAWSON ADAMS, Montreal, Canada. 1933. KARL EIKERS New York, N. Y. 1922. FEDERICO GIOLITTI Torino, Italy. 1906. SIR ROBERT A. HADFIELD London, England. 1921. FRANK WILLIAM HARBORD London, England. 1917. HERBERT HOOVER Washington, D. C. 1941. DANIEL COWAN JACKLING San Francisco, Calif. 1939. HENRY KRUMB New York, N. Y. 1921. C. McDERMID London, England. 1913. EZEQUIEL ORDONEZ Mexico City, Mexico. 1935. ROBERT PEELE New York, N. Y. 1938. A.M. PORTEVIN Paris France 1937. JOHN V.W. REYNDERS, New York, N. Y. 1937. GEORGE S. RICE Washington, D. C. 1911. ROBERT H. RICHARDS Cambridge, Mass. 1934. T.A. RICKARD Victoria, B.C., Canada

Jan 1, 1941

By V. F. STANLEY

THERE is not the slightest doubt that the present recoveries of valuable minerals by the Broken Hill mills could be improved, and that further machinery would be installed for the purpose if it could be assured that a high price of metals would be maintained; but concentration, like all other com¬mercial propositions, is a question of profit and loss, and no sensible metallurgist would carry out his work in such a manner as to obtain high recoveries at a financial loss to his company. There is a point in all concentration at which the added money obtained from the higher recovery of minerals is balanced by the extra cost of obtaining the last part of the recovery; a wise metallurgist will be content with his work before his working-expenditure reaches this point. To a casual observer, the work being done by the various Broken Hill mills is identically the same. A closer investigation will show that this is far from being the case, for it is a remarkable fact that, although the larger mines extend over a length of approximately only 2 miles, such a difference in the physical and chemical properties of the ores exists that, from the first reduction downwards, special treatment is necessary in each case, and hardly any two mills are identical in operation. The details of this paper refer directly- to the work of one . particular mill in Broken Hill, for the reason that the ore from each mine presents special difficulties and requires its own special treatment. I have selected the mill referred to because it has been constructed and modified under my supervision.

Sep 1, 1909

By John M. Cigan

Samples of copper-lead concentrates from the mine of Cia Minerals Santander, Inc., a Peruvian subsidiary of the St. Joseph Lead Co. were recently subjected to special analysis. This concentrate was known to contain bismuth which, under some circumstances, might have incurred a smelter penalty. In this case, customers for the concentrate accepted it and requested a higher concentration of bismuth. Although chemical analysis would disclose the presence of the metal, it was not possible with equipment available at the mill in Peru to determine the mode of occurrence in the fine grained ores.

Jan 11, 1964

By AIME

After an adventurous past-four changes of government in thirty years -the whole of Silesia and attached coal territories have become part of the Polish State. The coal resources of this area are the biggest among the European countries. Under a surface area of 5700 sq km are about 100 coal seams, with a total thickness of 150 meters. According to German estimates, there are some 150 billion metric tons of coal ranging in thickness up to 14 m within a depth of 1500 m. The seams are mostly level, free from faults, with good top and bottom; the coal is of excellent quality, hard and clean; and mining conditions are favorable. The mines are worked at considerable depth by means of vertical shafts and operate with cage and skip hoisting. Before the war, the mines were up to date, equipped with modern machines. Among the European countries, output per man shift was the highest ? 1.9 to 2.1 metric tons ? and cost of production was the lowest.

Jan 1, 1949

By C. H. Green

. RECENTLY two papers on the structure of eutectics were read before the British Institute of Metals, one by F. L. Brady1 and the other by A. Portevin.2 In the preparation of photomicrographs of laboratory specimens as illustrations for student work, and in connection with various researches; the writer has been working along the same line for some, time and, therefore, was much interested in the results given, especially those of Portevin. He has correlated the information on the subject and has outlined a broad scientific basis for future work along this line. It is largely with the idea-of adding something by way of illustration to the work already done that this paper is written. The eutectic is generally understood to mean the alloy having the lowest melting point of any alloy of the system, and in which the melt becomes supersaturated with reference to the two or more phases which, separate out simultaneously (or alternately). From the surface pattern, the eutectic means; a structure with no primary crystals. It is not always easy to get the exact eutectic composition in making any alloy; in fact, a slight range in composition may be expected and some of the coarser particles may be richer in either of the composing metals. Even when chemical analysis shows the right composition, differences in density of the pure metals may cause segregation, or. supercooling resulting from different crystallizing properties may give a surface pattern the appearance of being on one side of the eutectic point. However, the alloys on either side of the eutectic composition, showing primary crystals of one of the phases and the effect of the pro-eutectic form on the surface pattern of the eutectic make a very interesting study, which is slightly touched upon in this paper. The phases, or microconstituents, of a eutectic may be pure metals (Pb-Sb, Tl-Au), solid solutions (Cd-Zn), a pure metal and a solid solution; (Ag-Sn), or a pure metal or solid solution with an intermetallic compound (Sb-Mg, Sb-Cu, As-Cu, Bi-Te, etc.).

Jan 2, 1925

The Library of the above-named Societies is open from 9 A.M. to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The tine spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 10, 1917

JAmes E. Howard, Watertown, Mass.:—In connection with this paper, it is the desire of the Watertown laboratory to receive suggestions as to the lines of work and the particular direction along which the examination of the ingot-metal should proceed, and any suggestions so offered will be noted with care, and the tests conducted so as to embrace such features as it is thought desirable to have investigated. To me the question of structural continuity seems of para-

Jan 1, 1909

By J. E. Breen, J. Weertman

The creep rate of polycrystalline tin was studied as a function of temperature and stress in constant stress experiments. The temperature was varied from room temperature to almost the melting point of tin. Activation energies were calculated from tests run at the same stress. It was found that on a log creep rate vs inverse temperature plot the experimental points did not fall on one straight line but on a line which changed its slope in the 90° to 160°C region. Two activation energies for the creep of tin can be calculated from the data: a value around 26,000 cal per mol at high temperatures and a value around 11,000 cal per mot at low temperatures. It is suggested that the discrepancies between the creep activation energies and those of self-diffusion can be accounted for if self-diffusion takes place predominately by Zener's ring mechanism rather than through vacancy or interstitial movement. SHERBY, Orr, and Dorn' and Dorn' have recently reviewed some of the data on high temperature creep of metals. -The data show that the activation energy of high temperature creep is approximately equal to the activation energy of self-diffusion. This same correlation has also been successfully made between the activation energy of grain boundary relaxation and that of self-diffusion.3,4 The metal tin does not fit into this simple picture. Its activation energies of self-diffusion differ appreciably from that of grain boundary relaxation and of creep. Fensham,5 from a precisely performed experiment, has determined that the activation energies of self-diffusion of tin are 10,500 and 5,900 cal per mol along the C and A axes, respectively. There are two energies because of the anisotropic nature of tin. Rotherham, Smith, and Greenough6 have shown that the grain boundary relaxation activation energy is 19,000 cal per mol (measurements made from room temperature to 100°C). Puttick and King7 found the same activation energy for grain boundary slip in bicrystals of tin (180° to 225°C region). Until recently, there was no high temperature large strain creep data on tin suitable for activation energy calculations. At rather small strains (up to 0.01), Tyte8 had made a series of measurements on tin from which activation energies can be calculated. In Fig. 1 are plotted some of his data on a log creep rate vs inverse temperature graph. It can be seen that Tyte's work indicates that at a relatively low temperature the activation energy is around 7,400 cal per mol but at higher temperatures the activation energy increases. Since Tyte measured the creep only for small strains, it is doubtful if a

Jan 1, 1956

By R. D. Pehke, J. F. Elliott

The solubility of nitrogen in liquid pure iron has been measured as a function of pressure and temperature. Sieverts' Law is obeyed at all pressures up to 1 atm and the temperature coefficient of solubility is 8 x 106 %/°C. The solubility of nitrogen in liquid iron alloys has been studied by the Sieverts' method and by the sampling method. The solubility is decreased by Al, C, Co Cu, Ni, 0. Si atzd Sn, and it is increased by Cr, Cb, Mn, Mo, Ta, W, and V. Interaction coefficients eN, for the effect of these elements on nitrogen dissolved in liquid iron, are reported. 1 HE effect of nitrogen upon the properties of steel may be desirable or not, depending upon the composition, processing treatment, and the use of the product. To understand the behavior of nitrogen in the various steelmaking processes, it is necessary to have reliable fundamental data pertaining to the solubilities, rates of solution, and chemical reactions of nitrogen in steel, particularly in the liquid state. In an effort to extend our knowledge in these areas, an investigation of the thermodynamics and kinetics of the solubility of nitrogen in liquid iron alloys was undertaken. The thermodynamic aspects of the study are presented in this paper. The solubility of nitrogen in liquid pure iron has received the attention of several investigators whose results are summarized in Table I. Reasonable agreement among the more recent researches1-l8 is found for the solubility of approximately 0.044 wt pct at 1600°C and 1-atm pressure of N,, for the temperature coefficient of solubility being small but positive, and for adherence to Sieverts' law for pressures up to 1 atm. The solubility of nitrogen in a number of binary liquid iron alloys has been studied: Fe-A1,3 Fe-As,16 Fe-C,3, 71 18, 19, 20 Fe-Cr ,5,7, 10, 11, 15 21 Fe-Co,'4, '6 Fe-Cu,'6 Fe-Mn,10, 11, 18 Fe-Mo,13, 16 Fe-Ni,10, 11, 13, 15, 16 Fe-O,16, 17, l9 Fe-p,7 Fe-S,l6 Fe-Sb,16 Fe-Se,lg Fe-Si,4) 97 '77 187 19>2° Fe-Sn,16 and Fe-v.51 '3 A few ternary systems have been studied, most of which were reviewed by ~angenberg" who applied the methods suggested by WagnerPz3 Chipman,24 Darken and G~rry, and Morris and Buehl26 for predicting solubilities in multicomponent alloys. Langenberg22 and Humbert and Elliott15 compared the solubilities computed from simple binary alloy systems with experimental measurements of nitrogen solubilities in liquid iron containing two or more alloying elements. The interaction coefficients for nitrogen in

Jan 1, 1961