Search Documents

By P. H. Mell

THE little village, from which this formation receives its name, is situated on a bluff of the Alabama River, 175 feet above water level. This bluff is a portion of high table land that begins in the western portion of Choctaw and extends through Clarke and Monroe counties. We find points on this ridge more than 100 feet higher than Tuscaloosa, and nearly as high as the Tennessee River at Tuscumbia. Through this the Alabama River cuts its way, exposing a beautiful cross-section of the strata, of which the accompanying sketch may give some idea. The fossils are found about 75 feet below the surface and 100 feet above the level of the river. There are seven distinct strata. 1. The lowest, extending from the water's edge up the bluff 80 feet, is a soft calcareous rock containing about 15 per cent. of carbonate of lime, with occasional specks of mica. In this a few Ostrea, Turritellce, and Flustrce were found, but so friable as to fall to pieces when handled. 2. Next comes a stratum varying from 2 to 8 feet, consisting of

Jan 1, 1880

By R. V. Lundquist

Leaching manganese-bearing materials with NaOH to remove caustic-soluble silica has been demonstrated as a method for up- grading manganese. Those materials containing opaline varieties of silica respond most readily. Spent leach liquors are regenerated by treatment with lime to precipitate calcium silicate and to reactivate the NaOH for leaching.

Jan 4, 1953

By Walter Crooke

Regenerative hot-blast stoves are now in general use in all parts of the world, and are so well understood and appreciated, that I need not take up your time with an account of their history and introduction into the United States. My object in writing this paper is to give you a short description of a stove that is now being very favorably received and adopted here (see drawing). The stove was first introduced into this country in 1887 by M'Clure & Shuler (now M'Clure & Amsler), who have the management of the patent right in the United States. The English design had to be modified to suit the exigencies of American blast-furnace practice, which, in many respects, widely differs from our English experience. In the first place, the fire-bricks used in America expand to an extent unknown in England, and it became necessary to make special provision for this by increasing the number of cross-walls, and by leaving a space at the top of the stove through which the lining could expand. The expansion laterally was, however, more difficult to provide for, as the combustion-chamber in the center, being the hottest part of the stove, must necessarily expand more than the outer walls, and therefore tend to squeeze up the flue-openings. On first introducing these stoves to American ironmasters, a feel ing seemed to prevail that a " four-pass " stove did not utilize the whole of its surface. They also had an idea that the " two-pass " stove let the burning gas go before all the duty had been extracted from it; so that it was found neceseary to design a stove of a special character to suit their wishes. Hence the "three-pass" chimney top stove now before your notice, the advantage claimed for which is that each stove is independent, requiring no underground chimney flue or stack, and can be erected at a very light cost. The working of these stoves has proved to be very successful wherever they have been introduced.

Jan 1, 1891

Ira B. Joralemon, one of the world's most noted mining geologists, died last year at the age of 91. "His long professional career," says Donald H. McLaughlin, chairman of the executive committee at Homestake Mining Co., "covered an epoch in the history of mining that was unique in its opportunities and achievements," adding that many mining companies (Bunker Hill, Bralorne Mining, Copper Range, Anaconda, Newmont, Phelps Dodge, Homestake, etc.) greatly benefited from Joralemon's experience and wisdom.

Jan 12, 1976

RECEIPTS [Magazine Advertising $ 62,564.83 Magazine Sales 3,591.44 Totalm 66,156.27 Dues, Arrears7,032.88 Dues. Current96,839.74 Dues, New Members6,525.00 Dues, in advance 1,907.02 Initiation Fees7,584.00. Sale of Transactions3,909.03 Sale of Binding7,845.05 Sale of Special Editions 338.20 Sale of Year Book76.20 Sale of Pamphlets1,189.06 Sale of Authors' Reprints867.54 Miscellaneous Receipts62.93 Interest on Bank Balances1,712.89 Interest on General Reserve Fund337.50 Interest on Life Membership Fund557.84 Interest on James Douglas Library Fund....5,491.89 Total Receipts$208,433.04] [ ]

Jan 1, 1925

By Goodman, Richard E.

A complete rational analysis for design of excavation slopes and loaded rock masses is a desirable but perhaps unattainable goal. Irregular external and internal boundary conditions, poor understanding of failure criteria for large masses of rock, capricious material properties, and the importance of indeterminate forces and inaccessible and virtually un- sampleable rock defects emphasize the importance of experience in this aspect of rock engineering. The experience must be correlated with geological factors. In certain regions the accumulation of such experience through the observation of existing rock slopes in various formations constitutes an important aspect of studies for design of rock excavations.

Jan 1, 1969

By H. K. Najarian

AT Josephtown, Pa., on the south hank of the Ohio River about thirty miles northwest of Pittsburgh, is the Josephtown electrothermic zinc smelter, which operates as a custom smelter receiving both domestic and foreign concentrates. Constructed in 1930, the plant was designed to produce zinc oxide and to process 124 tons per day of zinc concentrate obtained mainly from the Company's New York State mines. Zinc condensing equipment was developed in conjunction with the St. Joe electrothermic. furnace and commercial production of zinc metal started in 1936. Expansion of the plant and equipment during 1939 and 1940 brought the processing. capacity to upwards of 300 tons of concentrate per day; and the plant operated at peak capacity during the war years, earning the Army-Navy "E" award and three subsequent stars. A postwar plant expansion is now under way, designed to increase the capacity to 500 tons per day of concentrate, with an estimated daily production of 160 tons of zinc metal of various grades, about 100 tons of zinc oxide, and 425 tons of sulphuric acid as major products.

Jan 1, 1947

By V. D. Perry

Carlisle: Reno, let's start off by asking "When was the first day that you began working in your profession?" Sales: I began in Butte, Montana, on August 22, 1900 as an assistant engineer for the Boston & Montana Consolidated Copper and Silver Mining Co., and continued at that job for about a year. The general manager was C. S. Batterman, and the mines- Mountain View, Pennsylvania, Leonard, East Colusa, and one or two others-were part of Boston & Montana.

Jan 5, 1966

By Victor J. Miller

The Northeast Tripp Slide is one of the larger slope failures that can be attributed to open pit mining. It is a 11.7 million cubic meter (15.3 x l0 6 yd3) wedge failure created by two thick gouge-filled fault zones whose intersection plunges into the Tripp pit at 13°. One unique aspect of this failure is that the slide is now stable despite having moved an estimated 8.5m (28 ft.) towards the pit and having reached a maximum overall velocity of 2lmmlday (0.07 ft/day). The slide started to fail in 1968, accelerated until mining in the slide's toe area was halted in April 1970, then began to decelerate. With the cessation of mining in the toe area, rubblized rock sloughed into the pit bottom which added weight to the failures toe constraints and began the stabilization process. Measurements from a network of survey stations revealed a correlation between the slide's velocity and heavy precipitation. Runoff water accumulating in the tension cracks is believed responsible for this correlation. Moreover, the survey net measurements showed that during the failure's last stage the vertical component of the slide's movement greatly increased. It is proposed that this settling was caused by plastic-like flowage of the clay gouge underlying the failure The fault zone's effective shear strength was estimated by a back- analysis on the wedge's geometry and by performing direct shear tests. The tests, performed on cores taken from samples that were collected on the failure, yielded a residual shear strength of: cohesion 0.61 kg/cm2 (8.7 lb/in2), and a friction angle of 9.6°. This residual shear strength was near1y equal to the back-calculated strength indicating that the controlling fault's effective strength was essentially the same as the residual shear strength of the gouge filling

Jan 1, 1983

"NAME…""Utah"" is derived from the name of the Indian tribe, variously spelled ""Yuta, “Ute"" ""Youta,"" ""Uta,"" ""Eutaw,"" and finally ""Utah."" It means ""in the tops of the mountains,"" or ""on the heights."" The state emblem is the ""Beehive,"" typical of industry. State nickname is ""Beehive State.""AREA…Utah is the tenth state in area. It contains 84,990 square miles, of which 2,806 miles are water. When admitted as a territory in 1850, Utah included all the area from the east line of California to the summit of the Rocky Mountains between the 37th and 42nd parallels, which embraced practically all of the present state of Nevada, all of western Colorado, part of Idaho and part of Wyoming, in addition to the present area of Utah.TOPOGRAPHY…Utah is generally mountainous, with several main ranges and also detached groups of mountains. The valleys are broad and level. The mean altitude of the state is 6,100 feet above sea level, which makes the state the third highest of the Union. The highest point in Utah is King's Peak (13,498) in the Uinta range. The lowest point is Beaverdam Creek (2,000) in Washington county.CLIMATE…The climate is diversified between mild temperate in the northern portion to semitropical in the southern portion. There are four distinct seasons. Snowfall is heavy at the greater altitudes and rare in the southern portion. Rainfall is moderate throughout the state. Extremes of heat and cold are unusual."

Jan 1, 1925

By AIME AIME

AT the end of September, ' the metal-producing industries were almost prostrate, the production of fuels was largely curtailed, there was a fair degree of activity in general manufacturing, while retail trade was moderately good. Looking at industry on the whole, there was a large percentage of unemployment, the degree of which has increased, progressively, month by month since the beginning of 1921. There is the prospect of much destitution and misery this winter; yet while' in some, quarters, idle workers are already being fed from, commissaries; in other quarters profligacy; in "spending continues, unabated. Amid this confusion in conditions there is;' much that appears paradoxical, but in fact it is not so and indeed everything is running pretty true to form: Such activity in production as there is to be seen is mainly in textiles; - leather goods, foodstuffs, etc., i.e., consumption goods for immediate use. Even in hard times 105,000,000 people must buy a good deal of clothing and food. Besides this there is indispensable repair work and- maintenances. Thus, the good business of the year in white lead for painting. The chief uses for the metals, however, are in the production of capital goods, and except for occasional and special reasons nobody in his senses is capitalizing anything at present prices for labor. Hence several millions of men are idle. The impoverishment of Europe and the exhaustion of her credits adds to this by curtailing our export trade.

Jan 1, 1921

By Albert D. Brokaw

THE accompanying chart was devised to provide a rapid and simple method of correcting for temperature and compressibility (deviation from Boyle's law) of gas under relatively high pressures and temperatures, such as are encountered in many deep reservoirs. The chart was prepared by interpolating for the desired values in the experimental data of Burke and Keyes1 and Kvalnes and Gaddy2 on the compressibility of methane, after adjusting their results from 0°C. to 60°F. and combining the correction factors for compressibility and temperature into a single multiplier, which, applied to the product of pressure and reservoir volume, gives at once the volume at one atmosphere (14.7 lb. per sq. in. abs.) and 60°F. The relationship 0f this multiplier to the compressibility factor Z, as used in most discussions, is simply: [Multiplier = 460° + 60°ZT –] where Z is the compressibility factor and T the absolute temperature (Rankine). Fahrenheit temperatures are shown on the vertical axis and pressures in pounds per square inch absolute on the horizontal axis. Correction factors or multipliers at intervals of 0.05 from 0.55 to 1.40 have been plotted on the chart and are calculated t0 give volume of gas at one atmosphere pressure (14.7 lb.) and 60°F. The operation is as follows: The reservoir volume, times the number of atmospheres pressure, times the multiplier, gives the volume of gas measured at one atmosphere (14.7 lb. per sq. in.) and 60°F. For example, a reservoir is estimated to have a volume of 10,000,000 cu. ft., bottom-hole pressure is 2940 lb. per sq. in. and temperature is 184°F To make the correction for methane, follow the 184° line horizontally to the 2940-lb. pressure line. The intersection lies between the 0.85 and 0.90 correction lines, and by interpolation we may estimate the multiplier at 0.863. The computation is simply: [ ] Using the chart for methane prepared by Prof. G. G. Brown3 and his associates, the multiplier is found to be 0.867. Details 0f computation are as follows: Correction factor to apply to PV to correct for deviation from Boyle's law and adjust to measurement basis of 60°F.: [ ]

Jan 1, 1941

By J. S. Kirkaldy, D. G. Fedak

The extra degree of freedonz introduced by a second independetzt concentration in a tenzary system gives rise to the possibility of unstable planar phase interfaces in semi-infinite diffision layer couples. Diffusion paths which pass continuously in and out of too-phase regions of the phase diagram but which are not coincident with tie-lines give rise to super saturated zones which may be either adjacent to or isolated from planar phase interfaces, with corresponding nonisolated or isolated precipitates. Nonisolated precipitates are equivalent to morphological development of the interface. Selected couples in the ternary systems Fe-Ni-Cr and Cu-Zn-Sn have been examined nzetallographically and ifz the latter case both isolated and uo~zisolated precipitates have been observed. The diffusion path in one of the couples showing interface morphological developtnent has been examitled using electron probe microanalysis. IGNORING the spurious effects of preferential grain boundary diffusion and anisotropic crystal growth7 it can be unequivocally stated that it is impossible for a binary isothermal diffusion couple constructed of two unsaturated phases to sustain a nonplanar phase interface. Consider for demonstrative purposes the schematic phase diagram of Fig. l(a). Given an initial flat phase interface, semi-infinite boundary conditions and the internal boundary condition fixed by the constitution diagram, xB = xB(T), the unique solution of the diffusion equation requires a persistent flat interface. No other solution is possible. If, however, we anticipate the involvement of surface tension, then the internal boundary condition must be written xB = xB (T,Y) where r is the radius of curvature of a hypothetical nonplanar interface. The introduction of a new parameter such as r can be equivalent to the release of an internal constraint, so that a stable nonplanar interface may be possible after all. Consider a perturbation to the interface as indicated in Fig. 1(b). According to the Ostwald-Freundlich equation: which is applicable to a system of this constitution, the solubility of A in the matrix ß ,xB (Y), at a point of curvature r is given by where Va is the molar volume of the a-phase, R is the gas constant, and a is the interfacial tension. Since the right hand side is positive, xB(r) >xB cm, as indicated in Figs. 1(a) and 1(c). Accordingly, the perturbation will carry the interface concentration in a direction which is opposite to that which would sustain local equilibrium. Such a perturbation is necessarily moderated and the system is returned to its initial condition. This result is general for all binary couples since we can regard an interfacial perturbation as an attempt to precipitate within un-

Jan 1, 1962

By THOMAS LEONBRD WATSON

INTRODUCTION. IN a paper read by title at the Washington meeting of the Institute, May, 1905,1 discussed at considerable length the geological relations, node of occurrence, and the genesis of the lead- and zinc-ores of the Virginia-Tennessee region. The present paper treats of the purely economic phases of the zinc-ores of the district; such as methods of mining the ores, their preparation and treatment. The Albemarle county mines and plant were discussed in the paper referred to above, and will not be considered here. METHODS OF MINING. Until very recently the mining of lead- and zinc-ores in Virginia was limited wholly to the surface belt of weathering. The mode of occurrence and the character of the ores to be mined were such as to demand the employment of methods used in mining secondary concentrated ores. Accordingly, a system similar to that practiced in mining brown iron-ores was employed, being modified to meet the changed conditions. Oxidized or Soft Ores.-Up to the present time practically all the ore mined in the Virginia district has been of the oxidized or soft type;-the silicate, calamine, and the carbonate, smith-sonite; largely the former, which has been localized and concentrated at only slight depths below the surface. Because of the extreme irregularity with which the limestone weathers when stripped of the overlying residual clay, it presents a roughened surface of large and small irregular "chimneys"

Mar 1, 1906

By Colin J. Dixon

The full realization of the potential of computers in geological in- formation system demands new approaches to the machine representation of information. At the same time, the feasibility of such a system, particularly in commercial field, demands greater freedom in input preparation and a degree of standardization in the arrangement of subject matter system. The paper describes some of the basic notions of project "GEOSEMANTICA 70". The aim of the project is to devise means of storing real geological informations in a machine rather than the representation of the information in human language form. This is seen as the only long-term solution to the problems of the complex vocabulary of geology and the complex syntax of geological description. Effectively, a machine language is being defined, consisting of a set of symbols and a date structure for representation of geological and related information. Beyond this, is the definition of a set of rules allowing the use of constrained text as an input/output medium. The investigation is oriented primarily to the representation and handling of information about mineral deposits and the associated geographic, economic and engineering information.

Jan 1, 1969

By H. J. C. MAC DONALD

THE mining engineer must have a chest of books snug enough for a camelback or to be stowed away in a canoe; at the lowest possible cost, as he needs it the most in those early years when he earns the least; but at the same time one having an unusually wide range, for he may have to cut down a forest, put up a sawmill, build mine towns, construct dams, power houses, power lines, and railroads. In fact he may be called upon for many unexpected accomplishments and all in extension of the characteristically broad demands of his profession. Suppose that an average mining engineer with a thorough theoretical training and a specialized mining education has accumulated, during a cosmopolitan experience, a complete and up-to-date library, but, unfortunately, in accepting a long term assignment to a far country he is forced to discard the greater part of

Jan 1, 1925

By Orville R. Lyons, A. C. Richardson

F. X. Ferney—We are pleased that this paper was presented at this meeting and thank Mr. Richardson and Mr. Lyons for their effort and work in preparing it. We agree with the authors that it was unfortunate that more comprehensive data were not available when the paper was prepared, this being particularly true since we had no knowledge that the paper was being written and could not make available data which were in our process files. Further, it is our opinion that because the data are not sufficiently comprehensive the results which are presented are erratic and will lead to false conclusions. As we see it, there are three Specific reasons why the data which are presented cannot be considered accurate. 1. The preparation plant was not at equilibrium while the samples were being taken. This is indicated by the fact that the percent of solids in the circulating water varied from 3.9 pct to 10.7 pct during the period when the plant was sampled. 2. We do not believe that the samples of Bird feed which were taken were representative and could indicatc the true feed to the filter. Evidence of this is shown in the data where the dewatered product leaving the centrifuge contains more coarse material than the feed to it, that is, material which is +6-mesh in size. 3. We question if the data concerning screen analysis in the fine sizes is accurate and would conclude (from the data) that these tests were made by a dry-screen method. We have found that wet screening is always necessary to obtain a true picture of the quantity of —200-mesh fines which is present. The test work described in the Lyons-Richardson paper was conducted some time ago and the tests were carried on during a period when the preparation plant had not ironed out all of their start-up problems. Since that time most of these problems have been corrected and now this is a smooth running, well-operated prep-

Jan 1, 1951

By Orville R. Lyons, A. C. Richardson

F. X. Ferney—We are pleased that this paper was presented at this meeting and thank Mr. Richardson and Mr. Lyons for their effort and work in preparing it. We agree with the authors that it was unfortunate that more comprehensive data were not available when the paper was prepared, this being particularly true since we had no knowledge that the paper was being written and could not make available data which were in our process files. Further, it is our opinion that because the data are not sufficiently comprehensive the results which are presented are erratic and will lead to false conclusions. As we see it, there are three Specific reasons why the data which are presented cannot be considered accurate. 1. The preparation plant was not at equilibrium while the samples were being taken. This is indicated by the fact that the percent of solids in the circulating water varied from 3.9 pct to 10.7 pct during the period when the plant was sampled. 2. We do not believe that the samples of Bird feed which were taken were representative and could indicatc the true feed to the filter. Evidence of this is shown in the data where the dewatered product leaving the centrifuge contains more coarse material than the feed to it, that is, material which is +6-mesh in size. 3. We question if the data concerning screen analysis in the fine sizes is accurate and would conclude (from the data) that these tests were made by a dry-screen method. We have found that wet screening is always necessary to obtain a true picture of the quantity of —200-mesh fines which is present. The test work described in the Lyons-Richardson paper was conducted some time ago and the tests were carried on during a period when the preparation plant had not ironed out all of their start-up problems. Since that time most of these problems have been corrected and now this is a smooth running, well-operated prep-

Jan 1, 1951

In Mr. Weed's interesting paper, frequent reference is made to the Cananea copper-deposits, which are said to have been so vigorously exploited that they produced 14,000,000 Ib. of copper in 1901. The ore-bodies which yielded this large quantity of metal are described as a product of contact-metamorphism, and in Mr. Weed's genetic classification of such deposits, they receive a place under the sub-heading, "Deposits impregnating and replacing beds of contact-zone."* They are considered by Mr. Weed to represent a special type under this head, and are further classified as: " l. Chalcopyrite deposits: (a) Pyrrhotite ores; (6) Magnetite ores, Cananea type." In condensing much information into a comparatively small space, the presentation of a subject may be so abbreviated as to detract from its clearness. The situation at La Cananea, considering its importance from an economic as well as scientific standpoint, may he worthy of more detailed description. As Mr. Weed rightly remarks, " structural differences are so important, and have SO marked a bearing, not alone on the theory of their genesis, hut also on the working of the deposits and a determination of their value as mines, that they merit a full discussion."† It is my present purpose: (1) to show that it is doubtful whether the copper of La Cananea is mined, except to a limited

Jan 1, 1903

By R. E. Crockett

MAGNETITE mining and milling in the Eastern States was at capacity during 1940, owing to the heavy industrial, defense, and war demand, coupled temporarily with the almost total stoppage of imports of foreign ores other than those under American ownership. In New York State the active mines were those operated by the Republic Steel Corp. at Mineville and Lyon Mountain. Republic's new concentrating mill at Port Henry, handling the Mineville ores, went into production about the first of April. Other large magnetite deposits in New York are currently being prospected and studied and may be under development in the near future. In New Jersey the Mt. Hope and

Jan 1, 1941