Search Documents

Philip Argall, Denver Col. (communication to the Secretary): Dr. Raymond claims (Trans., xxiii., 560)) that my statement (p. 557) regarding the crystallization of iron "is beyond question incorrect." He says: "It is not even settled that vibration will crystallize iron under any conditions." While admitting that authorities differ on the possibility of cold crystallization of iron, I believe it is a settled and undisputed fact that vibration in the presence of heat will crystallize iron. Bloxam and Huntington say :* " Vibration assists 'in converting fibrous metal (iron) back into a crystalline state when heated, a lower temperature sufficing than in the absence of vibration." Mr. A. F. Hill, summing up a very exhaustive review upon the crystallization of iron and steel, pronounces against crystallization, but only at temperatures below 900' F. Mr. Howe, discussing ,the breakage of a 20-foot porter-bar with a crystalline fracture, suggests that it was attributable to heat, jointly with the jar. We see, then, that vibration of heated iron bars will induce crystallization and consequent change of structure. Referring to my statement, I wish to point out, that I was discussing the vibration of stamps arid should have said, "vibration under all such conditions," etc. That is, vibration attended with sharp blows, such as a stamp-stem is subjected to, will crystallize iron; yet I believe that intense vibration under any condition will

Jan 1, 1895

By N. A. Gokcen

THE data of Chaudron,1 Tonosaki,2 and Collins³ on the thermodynamic properties of MOO, disagree widely. These authors, by using essentially similar methods, studied the following reaction: 1/2MoO2(s) + H2(g) == i/2Mo(s) + Ph,o H2O(g),K = —----- [1] Ph2 Tonosaki used a vacuum system consisting of a furnace containing MOO, and a water saturator whose temperature was kept at 25 °C with a thermostat. After repeated evacuation, hydrogen was admitted slowly into the system. The experiments were based upon the fact that at a constant furnace temperature and constant partial pressure of water, the total pressure of gas mixture over MOO? + Mo is constant. Any attempt to vary the pressure by external forces would vary only the amounts of MoO2, and Mo, after which the pressure should return to the equilibrium value in accordance with the equilibrium constant of reaction 1. The actual value of K was determined from the total equilibrium pressure (sum of Ph2o + Ph2) at each temperature. The total pressure of gas was varied within the range of 80.2 to 125.4 mm Hg, within a temperature range of 645" to 823 °C. The results were summarized as log K = 0.9413 — 1444.6/T for reaction 1. The ratio of H2O/H2 was considered to be uniform in spite of the presence of a thermal gradient across the static gas phase. It was shown by Rosenqvist and Cox,' however, that in somewhat similar circumstances the error resulting from thermal diffusion may be large. Collins³ improved Tonosaki's method by attempting to avoid thermal diffusion errors. His equilibrium data were obtained at 700°, 800°, and 900° C, and the result for reaction 1 was expressed as log K = 1.258 — 1822/T. The purpose of this investigation was to study reaction 1, avoiding the thermal diffusion errors, and to obtain equilibrium data in a considerably wide temperature range for the reliable extrapolation of the resulting thermodynamic functions. Experimental Procedure The diagram of the apparatus is shown in Fig. 1. Tank hydrogen was passed through a tube containing platinized asbestos at 425 °C in order to convert a trace of oxygen into water vapor. The flow rate was carefully controlled with a capillary-type flow-meter B and a bubbling column D. The gas was then presaturated sufficiently at P and led into a condenser system immersed in a thermostat, controlled to within ±0.002C. The temperature of the thermostat was measured with a thermometer calibrated against a certified standard. The temperature of P was adjusted to avoid the condensation of unduly large amounts of water as judged from the rate of flow out of the capillary tube M. Argon was purified by passing it through magnesium chips kept at 630°C. After passing through the flowmeter B', it was mixed with moist hydrogen emerging from the thermostat. The resulting gas mixture was then led into the hot zone of the furnace through the heated glass tubing and the silica tube S, thus insuring the same ratio of PII2o/Ph2 from the condenser to the reaction chamber, thus avoiding thermal diffusion. The entire gas system was of all-glass construction, except at the magnesium train. The furnace comprised a glazed alumina tube over which a 15-in. platinum coil was wound. The lower end of the alumina tube was tightly closed with a brass bottom and a silicone rubber gasket, and the upper end with two glass disks, each with a hole of 1/16 in. in diameter, through which the gas mixture escaped into the atmosphere. A back-up coil of kanthal wire facilitated the temperature control of the furnace. A coil of annealed molybdenum strip of 99.99 pct purity, 0.005 in. thick and 0.050 in. wide, and weighing 17 g was hung in the furnace with a 0.010-in. platinum wire attached to one end of a sensitive analytical balance. The temperature of the furnace was measured with a Pt-Pt-10 pct Rh thermocouple checked against a standard. The experimental procedure consisted of heating the gas purification trains, adjusting the gas flow rates, attaining a constant thermostatic temperature, flushing the entire system for 2 hr while heating the furnace to well above the expected equilibrium temperature and then cooling it at a rate of 0.3°C per min during which time the change in the weight of molybdenum was observed on the balance. For a given thermostatic temperature, i.e., a constant Prr,o/Px,, molybdenum oxidized upon cooling slightly below the equilibrium temperature. The procedure was then repeated by heating the furnace and thus reaching a temperature slightly above the equilibrium value. The average of the two temperatures, differing by 2" to 3"C, was considered to be the true equilibrium temperature. In order to determine the stoichiometric composition of the oxide phase present in this investigation,

Jan 1, 1954

By Joseph S. Malesky

The discovery and development of explosives mark one of the most important findings in the history of civilization. Without explosives our vast economic enterprise concerning the mining of coal, copper, iron, aluminum, and various other ores could not function. Explosives are used in all kinds of construction works, in the razing of old buildings, blasting of trenches, driving of tunnels, and in many other instances common to our everyday life. For these reasons explosives are rightfully referred to as the forerunner of progress. An explosive may be defined as a substance (usually a mixture) that, when flame or shock is applied, yields readily to rapid combustion or oxidation, accompanied by the formation of such relatively large quantities of gases as to produce much violence and pressure which, in turn, react against their surroundings and cause what is termed an explosion. By their very nature the action of explosives is destructive and disruptive of adjacent materials. Decomposition of explosives can occur through deflagration, which is rapid burning or combustion, as in the case of black powder, or through detonation, which is an almost instantaneous disruption, as in the case of dynamites and blasting agents. HISTORY OF BLASTING WITH EXPLOSIVES At one time workmen obtained stone blocks for building by grooving the rock with crude picks, driving wooden wedges into niches in the rock, and pouring water on the wedges; the swelling of the wood forced out the blocks. As late as the 17th century, fires were placed against the face of rock to crack it, and water was sometimes dashed on the heated rock to shatter it by sudden cooling. The progress of our country is synonymous with advancement of the improved manufacture and extended use of explosives. Coal had been

Jan 1, 1981

By C. S. Barrett, D. B. Masson

Martensitic transformations have been found in AgCd both upon cold-working at room temperature and cooling to lower temperatures. The crystal structures of the transformation products were found to be close-packed hexagonal in the first case and or-thorhombic in the latter. The transformation characteristics also were studied. Similar treatment of AuZn alloys failed to yield any transformation. THE literature on martensitic transformations of body-centered cubic metals and alloys indicates widespread instability of this structure at low temperatures, a tendency which merits further study. The body-centered cubic ß-phase of CuZn, for example, when it contained less than 42 wt pct Zn, was found by Greninger and Mooradian' and others' to transform on cooling to subzero temperatures to a phase that was tentatively considered to be tetragonal. Further work by Massalski and Barrett" demonstrated that cold work at low temperatures causes a partial transformation of ß CuZn of higher Zn content. The structures of the strain-induced transformation products were found to be different from those induced by simple cooling. Another well-known martensitic transformation among body-centered cubic phases is that of ß AuCd, first studied with X-rays by Olander,' then very thoroughly by Chang and Read.5,6 Here again transformation was found to occur both as a result of cooling and of strain. The alkali metals Li and Na, as well as certain Li-Mg alloys, also undergo transformation from their normal body-centered cubic structure, both on cooling and on cold-working. The phase AgCd, the subject of the present report, should be expected to behave quite similarly to CuZn for a number of reasons. It is the chemical analogue of CuZn, silver being directly below copper and cadmium directly below zinc in the periodic table. The size factors (percent difference in size) of the atoms, possibly a consideration in the stability of the ß-phases, are +3.1 in AgCd and + 4.2 in CuZn. Likewise the relative electronegativities of the two pairs of metals are about the same, CuZn possessing an electronegativity difference of 1.0 and AgCd one of 0.8. These values are from a table of electronegativities given by Darken and Gurry." The phase diagrams of the two systems around 50 atomic percent are similar, both possessing a disordered body-centered cubic phase, ß, at high temperatures and an ordered bcc phase, ß, at room temperature; however, the ß and ß' phases of AgCd are separated by a hexagonal phase, [, stable in the range 220-440oC, which has no analogue in CuZn. There has been confusion in the literature as to the structures of the ß' and [-phases. The phase diagram in the ASM handbook'" has the structures of the two phases interchanged; however, Hansen" reports the correct relative positions and Muldawer" verified that ß', the low-temperature phase, is body-centered cubic. Work by the present authors also

Jan 1, 1959

By Oswald J. Heinrich

(Read at the Philadelphia Meeting, February, 1878.) DURING the last twenty years much has been done to investigate and define the Mesozoic formation of the United States along the Atlantic States, as well as in the Territories. The investigations of Professors Hitchcock, Emmons, Hayden, H. D. Rogers, and those now in progress in connection with the geological surveys of Penn-

Jan 1, 1878

By Nicholas J. Grant, Oliver Preston

PUBLICATION of data by Irmann' indicating outstanding thermal stability and elevated-temperature strength properties in a sintered aluminum powder product (SAP) stimulated interest in the strengthening of metals by means of a highly dispersed oxide phase. This material was produced by compacting, sintering and extruding a fine flake aluminum powder, resulting in a dense product containing 10 to 16 volume pct alumina, which arises from the thin oxide film on the starting powder, highly dispersed in a matrix of pure aluminum. The method of producing SAP, and the stable high-temperature properties obtained from it, introduced the possibility of developing superior materials for high-temperature service by powder metallurgy methods. The composition of the materials of this type which are presently under consideration is predominantly metallic, containing from less than 1 pct up to about 20 volume pct of the oxide. As a result, other properties of these materials, such as electrical and thermal conductivity, thermal shock resistance, and to a certain extent ductility, notch sensitivity, machinability and hot working properties, are also predominantly metallic. These alloys do not constitute, therefore, a completely new class of materials as do the cermets, but rather present a new means of modifying the properties of a metallic matrix. In this sense, SAP type alloys are more closely analogous to the alloy aging systems. While the strength properties realized in the oxide-pure metal systems at the lower temperatures are substantially less than the best attainable in the aging systems, the thermal instabilities in the latter make them of less value for use at temperature much above their optimum aging temperatures, as indicated in Fig. 1. While the means of obtaining an oxide dispersion are more difficult and costly than conventional aging processes, in the light of the as yet limited understanding of such systems there is considerable promise of improved high temperature properties arising from the thermal stability of these structures. Since the development of SAP in 1946, its properties and the properties of a series of similarAl,O,-A1 products containing from about 1 to 20 pct aluminum oxide have been fairly extensively studied and reported.'- "articular attention has been given to

Jan 1, 1958

By Ira Joralemon

THE Ajo copper district is in the heart of the Arizona desert, near the western boundary of Pima county. Gila Bend, the nearest railroad point, is 43 miles north of the camp, and the little Mexican border town of Sonoita is 30 miles south. Between Gila Bend and Sonoita, Ajo is the only settlement save for one or two small cattle ranches and the uncertain villages of nomadic Papago families. The Little Ajo mountains rise a few hundred feet above wide desert valleys, beyond which are lava mesas. The camp itself lies at an elevation of about 1,900 ft. above sea level, in a little basin on the east side of the range, separated from the open desert by low hills. In the center of the basin the brilliantly iron and copper stained rocks of Copper mountain rise 150 ft. above -the village. Many varieties of cactus and low desert bushes cover the hills, while in the large valleys there are clusters of mesquite paloverde, and ironwood trees which furnish limited amounts of fairly good fuel. A scanty supply of water is obtained from wells in the desert and from prospect pits in the camp. The nearest abundant source of water is the Gila river, 50 miles north of Ajo. (See Fig. 1.) HISTORY OF THE AJO DISTRICT The Ajo, next to Santa Rita, New Mexico, is claimed to have been the first copper district in the Southwest worked by Americans. In the '60's or even earlier high-grade native copper and cuprite Ore was mined from shallow surface workings and hauled by bull team 400 miles across the desert to San Diego. From there it was carried in sailing ships to Swansea, Wales. Later, the ore was hauled to Yuma, floated down the Colorado river to the Gulf Of California, and shipped to Swansea. Bat-infested old workings and the massive axles of the bull carts are shown to prove the truth of the stories.

Jan 8, 1914

By W. M. Gray

The determination of the state of stress existing at a point in any solid body requires the determination of the six components of the stress tensor relative to a convenient set of axes. One general method of doing this in rock is to make strain or deformation measurements associated with local relief of stress in a number of boreholes penetrating a limited volume in the vicinity of the point at which the stress is to be determined. The stress is assumed to be constant throughout this volume. Leeman1 has described a number of the instruments that have been developed for making deformation or strain measurements in boreholes. Panek2 has described the application of statistical methods to the determination of the average components of ground stress from sets of measurements made in boreholes by means of deformation meters of the type developed by the U.S. Bureau of Mines. In this paper attention is given initially to the strain cell developed for use on the flattened ends of boreholes by the Council for Scientific and Industrial Research (CSIR) , South Africa. The equations required for evaluating the average components of ground stress from measurements made by means of the CSIR strain cell are derived. These equations are similar in form to those applying to measurements made by the borehole deformation meter developed by the U.S. Bureau of Mines. The results of an investigation of the properties of the equations are described. These results are important in the practical use of both the instruments mentioned above and any instrument based on similar principles.

Jan 1, 1968

By H. G. Doll

A new logging method, called induction logging, is described; it measures the conductivity, or resistivity, of the strata traversed by a bore hole. The apparatus, which is briefly described, comprises a coil system coupled with the ground by induction, so that there is no need for direct contact with the mud, or with the formations. For that reason, the method is particularly useful in oil base mud, and it was first applied to that case. A discussion concerning the respective contribution of each region of ground in the vicinity of the coil system is given. Through the concept of a geometrical factor, it is demonstrated that the total signal, which measures the apparent conductivity, is the summation of the partial products — geometrical factor by conductivity — for the different regions of the ground under consideration. It is thus possible to establish, for each type of coil arangement, investigation characteristic as well as departure curves and correction charts for beds of various thicknesses. This should greatly facilitate the quantative interpretation of the field logs, even in cases where such interpretation would have been difficult on electric logs taken with electrodes. It is also shown that focussing combinations of coils can be used, which give, directly on the recorded log, a value close to the true conductivity, even for fairly thin beds, thus eliminating in most cases the need for corrections. These focussing systems also give a sharper definition of the boundaries between successive strain.

Jan 1, 1949

By H. G. Doll

A new logging method, called induction logging, is described; it measures the conductivity, or resistivity, of the strata traversed by a bore hole. The apparatus, which is briefly described, comprises a coil system coupled with the ground by induction, so that there is no need for direct contact with the mud, or with the formations. For that reason, the method is particularly useful in oil base mud, and it was first applied to that case. A discussion concerning the respective contribution of each region of ground in the vicinity of the coil system is given. Through the concept of a geometrical factor, it is demonstrated that the total signal, which measures the apparent conductivity, is the summation of the partial products — geometrical factor by conductivity — for the different regions of the ground under consideration. It is thus possible to establish, for each type of coil arangement, investigation characteristic as well as departure curves and correction charts for beds of various thicknesses. This should greatly facilitate the quantative interpretation of the field logs, even in cases where such interpretation would have been difficult on electric logs taken with electrodes. It is also shown that focussing combinations of coils can be used, which give, directly on the recorded log, a value close to the true conductivity, even for fairly thin beds, thus eliminating in most cases the need for corrections. These focussing systems also give a sharper definition of the boundaries between successive strain.

Jan 1, 1949

By Henry Hebley

IN preparing this paper it has been the aim of the writer to keep the problems of both producers and consumers in mind. Until now, no attempt has been made to familiarize each group with the other's practice and limitations. This paper is an effort to acquaint the readers with some of the factors pertaining to the problem and cost of mining and preparing steam coal, and also to the economics of producing steam with such coal. In recent years all lines of endeavor have turned to intensive mechani-zation in order to lower the unit cost of production. The average fuel consumption in steam electric generating stations has dropped in 20 years from 4.0 lb. to 1.4.1b. per kilowatt-hour; while the modern power station can generate 1 kw-hr. on a fraction under 1 lb., or 13,000 B.t.u. coal. Also, the amount produced per man has in that same period risen from 3.8 to 8.2 tons, owing to the use of modernized equipment below ground for coal cutting, drilling, shooting, loading, hauling and hoisting. Unfortunately, the rapid speed of 5 tons per minute of operation at which the coal is loaded mechanically precludes any appreciable removal of impurities at the coal face, so that the raw coal is hoisted containing a markedly higher percentage of impurities than the hand-loaded coal, which was subjected to the scrutiny of the miner during loading. Also, during the past 20 years, certain seams of coal lying close to the surface have been made economically available by the improved design of electrically operated shovels and draglines for the removal of overbur-den running as high as 56 ft. This strip coal frequently contains so much ash in the raw state (Table 1) that it would have no sales value. There-fore, coal preparation must be adopted to beneficiate the raw product. Some seams in the United States have a decreasing ash content with decreasing size, owing, in all probability, to the fact that the coal is friable while the impurities are hard, causing a concentration of the low-ash material in the fine sizes. Illinois No. 6 coal being rather hard, naturally the reverse is true.

Jan 1, 1937

By R. M. Brick

AN increased demand for information in regard to the effect of gaseous elements in steel has accompanied the recognition of the importance of grain size. Attempts to correlate grain-size characteristics with gas con-tent, particularly oxygen in solution or in the form of included metallic oxides, have not been universally successful. Certain definite effects of dissolved gases are recognized; specifically, the role of hydrogen in causing internal cracks or "flakes" and that of nitrogen in preventing excessive grain growth of ferritic chromium steels. When irregular behavior or properties are found in a well-known steel and no definite cause for the abnormality may be assigned on the basis of chemical and metallographic tests, dissolved gases are frequently blamed as the culprits. The solubilities of hydrogen1 and nitrogen2 in pure liquid iron are known but of the ternary systems, iron-alloying element-gas, only the Fe-Si-N3 and Fe-Cr-N systems have received attention and here the study was confined to liquid alloys. Krivobok4 published a curve show-ing the solubility of nitrogen in liquid Fe-Cr alloys but gave no informa-tion on the experimental procedure employed. The considerable experimental work reported on the Cr-N binary alloys has been reviewed by Hansen.5 It is generally agreed that the nitride CrN is a stable phase although the existence of nitrides within limited temperature ranges of stability, viz., Cr3N2 and Cr2N, has been disputed, Adcock6 and others7 have reported a eutectic between Cr and CrN at 1580°C., although the supporting evidence is not complete.

Jan 1, 1940

By B. Woyski

MANY writers, in discussing defects caused by oxidation and gassing of bronzes and red brasses advocate substantially the same cure for both. But from its nature, oxidation cannot take place if there is an excess of fuel in the furnace, while the gases absorbed by some alloys are products of incomplete combustion of the fuel. Hence the metal can be either oxidized or gassed, but it is doubtful whether these actions can take place simultaneously. Oxidation can be easily overcome by the use of deoxidizers or it may be avoided by protecting the molten metal with suitable fluxes. Absorption of gases is more difficult to overcome. The regulation of the air and fuel, so as to produce complete combustion, and the protection of the bath by mineral fluxes are the most important factors. Gas expulsion, resulting in gas holes, porosity, unsoundness, and swollen or cauliflower-headed risers, is said to have several causes. One writer' lists the most common causes in the order of their importance, as follows: Superheated metal, dirty or slaggy furnace conditions, using metals low in quality or those previously subjected to bad melting practice, poor grade of fuel, use of newly lined or damp ladles, indiscriminate mixing of scrap or illogical combinations of metal. Superheating the metal usually occurs when the heat is ready to be poured but for some reason must be held in the furnace. In this case, a careful furnace tender tries to avoid overheating the metal by keeping a mild fire; that is, a reducing fire which, unfortunately, results in gassing the metal. A dirty, slaggy furnace may result in gassing the metal by retarding the heating and prolonging the time necessary to bring the metal to the proper temperature, thereby increasing the chances of gassing in uncertain furnace atmosphere.

Jan 5, 1922

By D. J. McAdam, G. W. Geil, R. W. Mebs

As shown in previous papers by the authorsg-17t the resistance of a metal to fracture, like its resistance to plastic deformation, is a function of all three principal stresses. A technical cohesion limit is the technically determined resistance to fracture under a specific stress system. The technical cohesive strength thus comprises an infinite number of technical cohesion limits corresponding to the infinite number Of possible com-binations of the principal stresses. The technical cohesive strength, therefore, may be represented by a surface in a diagram with the three principal stresses as coordinates. As shown in previous papers,'-'' the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress,$ namely, the stress system, plastic deformation, temperature, and the strain rate. More- over, the influence of each of these factors on the technical cohesion limit has been shown to be qualitatively similar to the three of the same factor on the flow stress.9-18 Advance of knowledge about the conditions determining fracture of metals has been retarded by the reluctance of some investigators to abandon preconceived ideas about how metals ''should,, behave. The incorrect idea is still prevalent that the conditions determining resistance to fracture are very different from those determining the flow stress. Attempts are still being made to express resistance to fracture in terms of a single parameter, such as a limiting value of the greatest principal stress, the maximum shearing stress, or the volume stress (one-third the algebraic sum of the three principal stresses). In these attempts, a sharp distinction is sometimes made between a ductile or ,plasticdeformation, fracture,, and a "brittle frat-ture.H In making this distinction, however, the meaning attached to the term "brittle fracture" sometimes is not made clear. The term could mean fracture after very little plastic deformation or it could be used to designate the type of fracture. An ordinary fracture of a ductile metal at room temperature starts as a cleavage, generally transverse to the direction of the greatest principal stress, but eventually changes to a shearing fracture' In some conditions, however, the metal fractures entirely by cleavage, with no evidence of plastic deformation during the fracture; the surface of such a fracture may have a

Jan 1, 1948

By R. W. Mebs, G. W. Geil, D. J. McAdam

As shown in previous papers by the authorsg-17t the resistance of a metal to fracture, like its resistance to plastic deformation, is a function of all three principal stresses. A technical cohesion limit is the technically determined resistance to fracture under a specific stress system. The technical cohesive strength thus comprises an infinite number of technical cohesion limits corresponding to the infinite number Of possible com-binations of the principal stresses. The technical cohesive strength, therefore, may be represented by a surface in a diagram with the three principal stresses as coordinates. As shown in previous papers,'-'' the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress,$ namely, the stress system, plastic deformation, temperature, and the strain rate. More- over, the influence of each of these factors on the technical cohesion limit has been shown to be qualitatively similar to the three of the same factor on the flow stress.9-18 Advance of knowledge about the conditions determining fracture of metals has been retarded by the reluctance of some investigators to abandon preconceived ideas about how metals ''should,, behave. The incorrect idea is still prevalent that the conditions determining resistance to fracture are very different from those determining the flow stress. Attempts are still being made to express resistance to fracture in terms of a single parameter, such as a limiting value of the greatest principal stress, the maximum shearing stress, or the volume stress (one-third the algebraic sum of the three principal stresses). In these attempts, a sharp distinction is sometimes made between a ductile or ,plasticdeformation, fracture,, and a "brittle frat-ture.H In making this distinction, however, the meaning attached to the term "brittle fracture" sometimes is not made clear. The term could mean fracture after very little plastic deformation or it could be used to designate the type of fracture. An ordinary fracture of a ductile metal at room temperature starts as a cleavage, generally transverse to the direction of the greatest principal stress, but eventually changes to a shearing fracture' In some conditions, however, the metal fractures entirely by cleavage, with no evidence of plastic deformation during the fracture; the surface of such a fracture may have a

Jan 1, 1948

By Charles E. Wait

HAVING had some experience in the use of gasoline-gas in a laboratory, I have been induced by frequent inquiry to present a few hints concerning it, which I hope may be of some value to those who are out of the reach of coal-gas, and who contemplate using this gas. While I will not delay to describe the method by which this gas is made, it may not be out of place to note that, unless frequent charges are put into the carburetter, the gas is variable in richness. This may be partially avoided, it is said, by repeatedly pumping from one cell in the carburetter to another. If a machine is in constant use for many months without re charging, the gas becomes rather poor for illuminating purposes ; but in this condition it may be burned in a Bunsen burner with advan tage. Could the gas be used always in this condition, no difficulty would be experienced, and it would be quite satisfactory for general laboratory purposes. Considerable annoyance, however, is experi enced whenever the machine is filled with gasoline. The Bunsen and other burners then produce a flame too smoky to be used with com fort, and, in fact, with most of them, a full supply of air; turned on at the base of the burner, will not suffice to completely burn off all the carbon. Finding it necessary to adopt some method by which I could get a flame free from unconsumed carbon, I adopted a plan which has in every way proved satisfactory. In addition to the pipe conveying the gas to the table, and ar ranged with a stopcock, there is brought to the table, within a fern inches of the gas-pipe, another pipe, conveying air direct from the pump. This pipe is also arranged with a stop-cock. The air- and gas-pipes are now connected with one pipe by a T joint; and to this last pipe is attached, by rubber tubing, the Bunsen or other burner. I have successfully used this simple system in connection with both small and large Bunsen burners, a burner with three tubes, arid a Fletcher burner; and recently I have added a new still to our equipment, and have been tising with it a Fletcher special high power burner No. 6, to which this system has been applied. With

Jan 1, 1886

By David R. Mitchell, Byron M. Bird

THE revision of this chapter has presented a problem in that heavy-medium jigging has come into the picture since the chapter was originally written (seven years ago), a practice in which an artificial medium is built up and maintained in the jig circuit. As this development makes the jig a "true" heavy-medium process, the method belongs in the chapter dealing with such processes. Although putting this development in its proper position in the book involves some repetition, this seems to be the best procedure, and it has been followed. As the chapter on jigs in its original form was intended to be more or less a handbook on jigging for the use of the practical man, and the great bulk of the material therein is still generally applicable, the text has been re-used in large measure. Two major changes should be noted: (1) the portion of the text relating to the refuse-withdrawing mechanism of the McNally-Pittsburg jig has been entirely rewritten, and (2) a description of the hutch valves on the Jeffrey jigs has been added. Jigging is the stratification of a mass of solid particles in upward and downward pulsations. The stratification usually is effected in a rectangular open-top container having a perforated bottom through which the pulsations of water are applied to the materials to be separated; in separating coal, to a mass of coal and refuse. Jigging usually is a continuous process involving three steps: (1) the reception of the raw coal, (2) the stratification of the coal and refuse so that the refuse settles to the screen plate, and (3) the overflow of the cleaned coal and the withdrawal of the refuse collected on the screen. The jig is the most universal washer ever devised. It is handling in practice a wide range of closely sized coals and ores, mixed sizes of coal from 8-in. to 0 through 3/4-in. to 0, and mixed sizes of ores down to 7/32-in. to 0and even smaller. It is treating materials ranging in specific gravity from that of gold at 19 to that of coal at 1.30. It is handling feeds in which the proportions of high-gravity materials range from 90 per cent or higher, as for some iron ores, to 10 per cent or less for some coals. It is handling feeds containing all shapes of particles-round, rectangular, and flat. It is handling simple separation problems and difficult separation problems.

Jan 1, 1950

By Bernard MacDonald

Of the treatment of the slime-pulp of gold- and silver-ores by cyanidation, agitation is an essential part. When prepared for treatment, this pulp, consisting of ore reduced to such fineness that approximately 80 per cent. of it will pass through a 200-mesh screen, is mixed with a certain proportion of water, carrying in solution the cluantity of cyanide (KCN) and other chemicals required. The water-constituent of the pulp thus prepared usually ranges from 1 to 2 parts by weight to 1 of the dry ore. Thus constituted, the pulp is charged into treatment-tanks, the shape and capacity of which vary, according to the quantity of pulp to be treated daily and the method of agitation to be employed. Tanks have no other function in a cyanide,plant than that of being economical and corlvellient containers or receptacles for holding the pulp, solutiou, or water used in the operations. It is by agitation that the solids in the pulp charged into the tanks are kept in suspension in, and mixed with, the solution in the proper proportions required for the treatment. If the proper mixture of solution to dolids be determined to be 2 to 1 by weight (which is, approximately, 5 to 1 by volume), this proportion should be maintained in every part of the charge; that is, each solid particle of the pulp, whether it be of' 180- or 400-mesh size, should be surrounded by five times its own volume of solution throughout the whole period of treatment. The reason is, that the amount of chemicals ascertaiued to be necessary for dissolving the gold and silver contained in the solids, is held in uniform solution in the water-constituent of the pulp, and, therefore, the determined proportions of solution and solids must be maintained at all times during treat-

Jan 1, 1912

Jan 1, 1969

By J. L. Bruce, N. B. Braly, F. A. Linforth, Wm. B. Daly, Paul A. Gow, C. L. Berrien, R. H. Sales, P. F. Beaudin, John Gillie, G. W. Roddewig

Butte mining district is situated in Silver Bow County, in the southwestern part of Montana. Butte originated as a placer mining camp, gold having been discovered in 1864, on Silver Bow Creek, near the southerly end of what is now Main Street. The Butte placer gold was heavily alloyed with silver, and only commanded $13 an ounce. Placer mining was vigorously prosecuted along Silver Bow Creek and its tributary gulches for about 5 years, at the end of which time, in 1870, the Butte camp was practically deserted. In the meantime, the quartz veins prominently traceable over the hillsides were located, the first location, July 12, 1864, being made by the Missoula Mining Co. and called the Missoula Lode Claim, and later relocated by G. 0. Humphreys. Reasoning from the presence of the gold placers, free milling gold and silver ores were eagerly looked for by the early prospectors. Claims covering the great Rainbow and other silver lodes were located in the 60's. The presence of valuable silver ores in these veins caused the staking of many claims, believed to be valuable only for silver, but which later, at depth, proved to be enormous copper producers.

Jan 1, 1925