Search Documents

By Norris Johnston, Carrol M. Beeson

For many years the permeability of reservoir sands has been measured by flowing air through a cleaned and dried core sample. This differs from the true reservoir permeability in one important respect: the rock particles in the reservoir are surrounded by interstitial water, not air, and their physical shape and condition of hydration are greatly dependent thereon. Permeability as defined must be measured with a single-phase fluid. Since no means exist for removing the oil and gas from a core sample by simply flowing water through it, the sample must be cleaned and then resatu-rated with water before testing. The present discussion attempts to show that after the cleaning process a considerably different permeability is determined with salt or fresh water than is obtained with air. The postulate is made that the salt-water permeability is probably closer to the true reservoir permeability than is the measurement with air. This is discussed in relation to both physically possible and economically feasible measuremerits. Data On more than 1200 core samples are given to show the nature of the effects observed, and a plea is made for others to consider water permeability measurements as a routine necessity, eventually replacing air permeability in regions where the differences are great. Introduction Permeability is defined1 as a "a measure of the capacity of a porous medium to transmit fluids, when there is no interaction between the solids and the fluid." Darcy's law of liquid flow in porous media states: kA?P QµL/A?L [I] where Q represents milliliters of liquid of viscosity p centipoises passed per second through a porous medium of permeability k darcys and cross-sectional area A sq. cm. under a pressure gradient ?P/L atmospheres per centimeter, the flow being understood to be laminar or viscous, not turbulent. This equation defines the darcy. For the case of radial flow in a uniform sand, such as usually exists in the neighborhood of a well in an oil or gas sand, Darcy's law becomes:2 Here h is the net sand thickness in feet, Pe and Pw are pressures at the drainage radius4 and well radius, and re and rw are these radii, respectively. The productivity index3 is defined as the barrels of liquid produced per day per pound per square inch mean pressure differential between ferences and well bore, and is thus: By further definition, the specific productivity index is: or in terms of practical units, and allowing for shrinkage:

Jan 1, 1945

By Hans Lundberg

IN ORDER to comprehend the help and information that may be expected from electrical prospecting, it is necessary to have at least a general knowledge of the methods and principles involved in preparing and interpreting results obtained in the field. Electrical prospecting is rather complicated, both in theory and practice, and in order to make a brief description clear to the practical mining man it has been necessary to idealize and generalize the problems, at the risk of having such simplification criticized by the theoretical man. This simplification must not be misinterpreted as showing a lack of theoretical knowledge. FIG. 1.-FLOW OF CURRENT IN AND AROUND A CONDUCTING BODY. For its operation, electrical prospecting mainly depends on-the fact that most metallic ores conduct an electric current much more readily than barren rocks. If an electric current flows through a block of ground within which a body of chalcopyrite is enclosed in country rock of schist, the current will find less resistance to its passage through the chalcopyrite than through the schist, even though the passage through the latter be much shorter. This is because the longer path through the chalcopyrite offers less resistance, owing to the superior electrical conductivity of the chalcopyrite (Fig. 1).

Jan 1, 1928

By Ingvar Janelid

13.7-1. General. Iron ore mining in western Europe is mostly carried out underground and only a minor part is mined by open pit methods. Actual open pits of importance in this connection are, among others, Svappavaara in Sweden, Mo i Rana and Sydvaranger in Norway, Corby Mines, Colsterworth, and Scunthorpe in Great Britain, and in western Africa, Nimba and Bong Range in Liberia, and Kedia d’Idjil in Mauritania. The open pit mines of western Africa are of great interest in this connection as they are designed according to European practice and have accepted the same techniques, methods, equipment, etc. as the European mines. In the surface mining of limestone, granite, shale, etc., the technical conditions generally are similar with those in the iron ore mines. Some information will therefore be submitted from typical quarries. The geological conditions at the various iron ore mines and limestone and other quarries vary extensively. In Scandinavia the iron ores occur exclusively in Precambrian rocks. The ore is hard, mostly magnetite or hematite, folded and steep dipping, and hence accessible to surface mining only in the shallow sections. In the mines referred to, open pit mining will last for another 10 to 30 years, whereupon mining has to be continued by underground methods. In France the Minette iron ore has previously been mined in open pits but, because of increased overburden, mining underground with room and pillar methods now dominates. The iron ores are Jurassic, flatlying strata of oolitic type, containing chamosite, siderite, and brown hematite. The British iron ores are mostly of the same origin and appearance as the French deposits, but despite heavy overburden they are preferably mined from the surface. In western Africa, the iron ores are of the same type as in Brazil, i.e., itabirites with high-grade portions resulting from silica-leaching and weathering. The ore contains mostly brown and blue hematite and magnetite. Nimba and Kedia d’Idjil are very similar regarding ore quality and geology. Bong Range is a deposit of low-grade ore which has to be concentrated.

Jan 1, 1968

By James Douglas

This sketch of the history, geography and topography of the American transcontinental railways is based upon a paper read many years ago by the author before the American Geographical Society, and now re-cast, with numerous modifications and additions required to bring it up to date. It was intended primarily for the information of members and guests of the Institute from the East attending the California meeting; and, with that purpose in view, the Secretary of the Institute compiled;

Jan 1, 1900

By John Wulff, J. H. Hollomon

THE opinion has been widely held that the corrosion of alpha brass occurs by the selective solution of zinc. As late as 1939, Fink1 and Evans2 suggested that in the initial stage of the corrosion the selective solution of zinc produces copper-rich areas, which subsequently act as cathodes that facilitate the deposition of copper. Previously Abrams3 had shown that most of the copper found on corroded brass was redeposited and not residual, although he did not consider the nature of the initiation of the corrosion process. Enough data exist to indicate that any metal surface is sufficiently heterogeneous to provide the anodes and cathodes necessary for the initiation of corrosion.4,5 Thus, for alpha brass we need postulate not an initial selective solution of zinc, but only the existence of local differences in electrochemical potential. The heterogeneity responsible for potential differences may arise from oxide and other films as well as from alloy concentration gradients. Even though selective corrosion may be possible in some alloy systems, previous data on alpha brass as well as the experimental work reported in this paper do not require this supposition. Bengough and May,6 in a discussion of Abrams' paper, first suggested the addition of small amounts of arsenic (0.03 per cent) to alpha brass to prevent the redeposition of copper (dezincification). This suggestion was later substantiated by Nixon.7 In their studies of the inhibiting influence of arsenic, Evans and Fink were led to the selective-solution hypothesis in order to explain the initial corrosion of such alloys. They believed that an arsenic film covered anode areas and prevented the formation of copper-rich spots capable of acting as cathodes for the deposition of copper. They did not consider, however, the mechanism by which the arsenical film was formed. Bengough and May,8 in another publication, suggested that the commonly found gray or black arsenical film may act to: (I) carry oxygen to the brass surface, (2) increase the discharge potential of copper on brass, (3) precipitate cuprous chloride from colloidal suspension in chloride solutions. Masing9 assumed that the film found upon arsenical brass was metallic arsenic. His measurements of hydrogen overvoltage of bulk arsenic led him to believe that the inhibition of dezincification occurs because the overvoltage of a brass surface is lowered by the arsenic film. He reasoned that this film would permit the more rapid reduction of hydrogen at the cathode, which would prevent the redeposition of copper. In a recent paper,10 we have pointed out that the film formed during the corrosion of arsenical brass and copper in stagnant solutions is essentially arsenious oxide (As203),

Jan 1, 1942

By E. L. Tucker

IN THE metallurgy of precious metals, it has been standard practice for years to use cyanogen compounds, so it was but natural that early investigators in the field of flotation should consider these compounds as possible flotation reagents. In Australian Patent 9508, of 1913, alkali cyanides were described as suitable reagents for the separation of heavy sulfide minerals, the reagents being employed either in an alka-line or neutral circuit. In U. S. Patent 1236501, of 1917, to John M. Tibbet, the use of cyanide in conjunction with soda ash or lime is described. One of the claims of this patent reads, "An improvement in the cyanide process for the treatment of ores comprising, mixing the ore with cyanide solution and oil and alkali: emulsifying the oil in the presence of the ore, the alkali and the cyanide solution, floating a portion of the values in the pulp by producing gas bubbles in the mixture-and removing the values floated." More recently, Sheridan and Griswold, in U. S. Patents 1421585 and 1427235, describe a somewhat similar process and have, successfully introduced it in. the mill of the Timber Butte Milling Co. U. S. Patent 1429544, of 1922, to Stevens, describes the use of double cyanides of copper, zinc, and lead. The success of cyanide as a reagent in the differential flotation of lead and zinc sulfides in highly complex ores is proof that these patents have a solid foundation.. Although the technique of their application to particular ores has been worked out in many cases, no one, so far as is known, has attempted to describe the nature of the action of the cyanide or to determine the ideal conditions for its, application. It was the purpose of the present investigation to gather information on these points. Naturally this would have been an exceedingly ambitious.

Jan 8, 1925

By Chandler Morse

RENEWABLE VS. NONRENEWABLE NATURAL RESOURCES Nonrenewable resources, such as minerals, are the inevitable center of attention in discussions of depletion and exhaustion. Nevertheless, it may well be proper to regard some nonrenewable resources as not subject to exhaustion, and renewable resources may sometimes be treated as if they were finite stocks. Thus, the availability of nonrenewable resources is not and probably never will be known completely Chap. 2.5A, and therefore is not subject to firm predictions concerning exhaustibility. Moreover, because exploration and discovery are more or less continuous processes it is often appropriate to regard mineral supplies as flows, and to treat the estimated reserves as working capital, an inventory, continually depleted by use and augmented by discoveries.23 The aggregate economically exploitable stocks of a given mineral are seldom estimated (or estimatable) with precision, as Chap. 2.5A shows, and even when they are, forecasts concerning years of remaining life can be and often are falsified by changes in one or more of the multidimensional conditions of supply and demand; or the productive services formerly derived from an exhausted stock may continue to provided without material impairment by one or more substitutes b Conversely, the renewable resources are all subject to depletion when the rate of use exceeds the natural or induced rate of replenishment, and cases of exhaustion or near exhaustion, as through soil erosion, overcuttmg of forest lands, and overfishing, are rather common c Where exhaustion is a clear possibility the resource may either be exploited on a consciously adopted "sustainable yield" basis or be treated as an exhausting asset." In some cases, conscious treatment

Jan 1, 1976

By George S. Rice

The subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on blimps in coal mines, and then presents suggestions arising from the writer's recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free from folding and faulting. Definition of Bumps Bumps in coal mines, as defined in this paper, are sudden violent bursts of coal that usually occur without warning in the extraction of pillars and may or may not be accompanied incidentally by falls of draw slate, upheaval of bottom and smashing of timbers. They are not known to occur where the advancing longwall method of mining, accompanied by

Jan 1, 1936

By George S. Rice

The subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on blimps in coal mines, and then presents suggestions arising from the writer's recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free from folding and faulting. Definition of Bumps Bumps in coal mines, as defined in this paper, are sudden violent bursts of coal that usually occur without warning in the extraction of pillars and may or may not be accompanied incidentally by falls of draw slate, upheaval of bottom and smashing of timbers. They are not known to occur where the advancing longwall method of mining, accompanied by

Jan 1, 1936

By G. Derge, W. Peifer, J. H. Richards

INTRODUCTION A WIDE variety of metallurgical defects in steel have commonly been attributed to the presence of excessive amounts of hydrogen. These defects include flakes in rails and forgings, cracks in welds, and blisters in enameled ware. They have been related to hydrogen largely by circumstantial evidence because the proper sampling and analysis of steel for hydrogen has been known to be difficult and because no general agreement has existed with regard to the relative suitability and accuracy of available methods. The need for a direct approach to these problems has been widely recognized. This general situation has been well described in the publications of the British Committee on the Heterogeneity of Steel Ingots,1 and current approaches to the problem were reviewed in a recent symposium of the AIME.12 The plans described by the present authors at that meeting have now matured satisfactorily and will form the basis of this paper. The principle object of this paper will be to describe the methods of sampling and analysis which have been developed and to illustrate the usefulness and limitations of these methods by citing their application to a specific problem. The first problem selected for investigation was the behavior of hydrogen in rail steel. This was chosen because the occurrence of shatter cracks in rails has received a great deal of study over a long period of time. The defect can be controlled by the expensive procedure of slow cooling. However, it may be hoped that a better understanding of the factors influencing the hydrogen content of rails will lead to a more efficient control of this problem. Rails provide a good starting point for a more general study of hydrogen in steel because they provide a cross section large enough to develop cracks, yet small enough for convenient handling and sampling. Rails were also selected because they are made from plain carbon steel and it was felt that the initial work should not be complicated by the effects introduced by alloying elements. The considerations which determined the original planning of this study should be reviewed. The inherently complex nature of most hydrogen problems requires that a large amount of data must be collected for any particular case. This in turn means that any analytical procedure should be as rapid and simple as possible. The same objective of speed is indicated by the fact that it may finally become desirable to use hydrogen analysis in process control. It is also known that hydrogen is highly fugitive and that any procedure which facilitates early analysis of the sample without prolonged or irregular storage has distinct advantages. The most important previously reported methods of analysis may be classified into three general groups: (I) Vacuum fusion. (2) Vacuum extraction (without melting). (3) Total combustion.

Jan 1, 1948

By Arne F. Westgren

X-ray analysis and single-crystal study have been utilized in recent years as a new means of following constitutional changes in alloys. If such transformations can be suppressed by rapid cooling, they can be followed at room temperature in a particularly convenient manner. In the following we shall consider changes in solubility and polymorphic transformations with particular reference to phenomena of the age-hardening type. Finally a thermodynamic viewpoint is developed for examining such transformations. Changes in Solubility 1. Determinations of solubility limits in the solid state which show decreasing solubility with falling temperature are made as follows: A series of alloys extending into the heterogeneous region is prepared and quenched fromas high a temperature as possible, whereupon their lattice parameters are determined. Then one or more alloys are quenched from temperatures at which they are heterogeneous and their lattice parameters likwwise determined. For the purpose of determining the parameter the apparatus shown in Fig. 1 has been very useful for it produces sharp films in a short time which can be accurately read. High-order reflections (interferences) from the object are recorded on a film which is placed exactly perpendicular to the X-ray beam. The specimen usually has the shape of a small round bar.l Fig. 2 shows a selection of such exposures of silver-rich Cu-Ag alloys, and Fig. 3 gives the measurements made from these films. Fig. 4 gives the solubility curve which results.2 This curve is shifted to lower concentrations than the curve that is obtained from metallographic or physical methods. The X-ray method unquestionably gives more reliable data

Jan 1, 1931

1910, hundreds of thousands of dollars of work and equipment in a 1500-foot shaft, crosscuts and pumping had found only copper-lean pyrite in two cross- cuts, and nothing in a third. Going aimlessly along the third crosscut one day, after looking at the barren face I happened to notice a dark spot in the white limestone, near the floor on one side. I picked, and found it was a little triangle of rich chalcopyrite. Next day I took Bill Gohring, then mine superintendent, in to see it. He said nothing else had succeeded so we might as well try that. The new drift broke into a full face of high grade copper ore in the first round, and continued in rich ore for 2200 feel broken only by a couple of short stretches of lean pyrite. The earlier crosscuts had happened to cut these lean areas. Q: Was there any single thing that called your attention to that little dark spot in the side of the Briggs crosscut, rather than to any other discolored spot? Joralemon: Nothing very definite. Maybe luck, maybe that indefinable subconscious thinking that

Jan 9, 1964

ALASKA Established November 19, 1947 Meets fourth Monday monthly except June through August Term of office ends October Peter O Sandvik, Chairman Denny G Breaid, Vice-Chairman Douglas W Huber, Secretary-Treasurer School of Mines University of Alaska P O Box 337 College, Alaska

Jan 1, 1958

By V. Jares

DESPITE the fact that a combination of metals-aluminum-zinc-tin, and sometimes aluminium-zinc-cadmium-is extensively used for aluminum solders, as well as for die-castings, the constitution of these alloys has not yet been made clear. I. BINARY SYSTEMS The system aluminium-zinc is the basis of the ternary alloys under consideration. Their composition was made sufficiently clear by the investigations of Roscnhein and Archbutt,1 Bauer and Vogel,2 Sander .and Meissner,3 Hanson and Gayler4 and Isihara.5 Only the temperature of decomposition of the crystals s seems still to be doubtful, whether it is considered as a compound of Al2Zn3 (according to Bauer and Vogel) or as an intermediate phase of variant composition (according to Hanson and Gayler). This temperature is given by most of the authors, as in the neighborhood of 256° C., only Isihara giving 280° C. As its accurate determination is of special importance in the study of the ternary alloys under consideration it was experimentally controlled in the following manner: An alloy corresponding in composition to the formula Al2Zn3 was made, in which the temperature effect was found to be the greatest. This was drilled and a silver-constantan thermoelement inserted into the cavity so as to be in direct contact with the alloy. The whole was then very slowly heated and the heating and cooling curves determined. The transition temperature from the heating curve was found to be 281° C., whereas-from the cooling curve it was 252° C.

Jan 10, 1926

By R. H. Hadfield

Professor ArnolD, of the Sheffield Technical School, who has done so much excellent work in metallurgical research, recently produced, with the aid of aluminum, a sound ingot and bar from the purest known Swedish brand containing 99.8 per cent. of pure iron. Table 1. shows the physical quantities of this metal. TABLE I.— Tests of a Sample of Almost Pure Iron Prepared by Professor Arnold from D. v Ewedish Bar, Containing Before Fusion 0.04 Per Cent. of Carbon. I. II.+ III. Series mark,.. 136 1.371F ...... C, 0.07 0.07 Si, 0.04 0.04 8, 0.02 0.03 ...... Analysis, per cent,. .. P, 0.02 0.015 ...... Mn, 0.06 0.07 Al, 003 ............ Fe, 99.76 99.81 ...... Specific gravity,........... 7.863 ...... Original diameter, inches,. .. 0.564 0.798 0.798 Original area, square inches,. . 0.25 0.50 0.50 Limit of elasticity, tons per square inch,...... 18. 3.8 Breaking-load, tons per square inch,. 21. 23. 14.75 Total elongation, per cent., measured on 2 in.,...... 50. 49.25 61. Total reduction of area, per cent.,. 80. 69.60 61.20 Extension at permanent set, per cent.,...... 0.007 ...... silky and Appearance of fracture,. .. . silky i granular in parts.

Jan 1, 1894

By E. A. Gulbransen, J. W. Hickman

IN a previous paper1 the authors have investigated the structure of the oxide films formed on most of the metals that make up the alloys of this study. The metals were studied in order to provide basic information on the structures, both physical and chemical, of the oxide films and to determine how these structures are effected by the temperature, time of oxidation, and surface preparation. It was felt that an understanding of the physical and chemical structure as well as the stability of the oxide film might furnish clues as to the nature of the reaction process and the protective quality of the film. The oxidation of the metals was studied over the temperature range 300° to 700°C. except for copper, where the range selected was 100° to 500°C. The results of these studies were presented in graphical form as existence diagram, of the oxides on a time-temperature scale. For some of the metals the existence diagrams were simple and showed few chemical transitions, but there were numerous cases where the physical state of the oxide surface was a function of time and temperature. In general the physical state of the oxide surface changed with increasing temperature so as to increase the sharpness of the diffraction patterns and to cause orientation effects to be more pronounced. Deviations in lattice parameters from X-ray values were noted. In general these deviations were of positive nature and may be due to solid solution of the metal in the oxide lattice. This effect might be expected in thin oxide films. In a study of the oxidation of alloys containing two or more metals, there may arise the complicating factor of identification of the oxides formed. A thorough understanding of the oxides formed on the pure metals, therefore, was, essential before investigation of the oxidation of alloys. In this paper it is our purpose to present a study of the following problems: I The existence diagrams of various alloys. [2.] The effect of the structure of the [ying] metal on the existence diagram of Iron. 3. The effect of the percentage of chromium on the oxides formed on Fe-Cr alloys. 4. The relationships, if any, between the oxides formed and the protective quality of the oxides. The following alloys are included in this study: alloys of iron with body- centered cubic, face-centered cubic and other metals, 13 Cr-Fe, 18-8 stainless steel, K42B1 Nichrome V, Hipernik, Inconel, Stellite " 21," Refractaloy, Kovar, mild steel, a series of Cr-Fe alloys and a series of Co-Fe alloys. Since many of the commercial alloys in this list contain more than two metals, various complicating factors in the identification of the oxides formed may arise.

Jan 1, 1946

By W. C. Ellis

NONFERROUS alloys upon which desirable properties can be conferred by heat treatment are becoming of increasing industrial importance. The alloys of copper with a constituent which has a solubility varying with temperature are materials of this character. Some of the constituents which are effective in producing a change in the mechanical properties of these alloys upon heat treatment are, according to Corson,1 nickel and silicon, iron and silicon, cobalt and silicon, and chromium and silicon. In addition to these elements, Gregg2 states that the combination of beryllium and silicon is effective in producing age-hardening characteristics in copper. The effect of these elements, however, as dispersion-hardening constituents in the copper alpha solid solutions does not seem to have been studied in any considerable detail. This paper deals with the heat treatment and properties of three alpha brasses containing 3 per cent. of nickel plus silicon in the proportion necessary to form the compound nickel silicide, Ni2Si. Some information of a preliminary nature in regard to the hardening by heat treatment of phosphor bronze containing the same percentages of nickel and silicon is included. The method of hardening the alloys, which is effective in increasing the tensile strength and proportional limit, is similar to that used in, the case of duralumin type aluminum alloys. It consists of a quench from a temperature at which the hardening constituent is in solid solution, followed by an aging at a lower temperature to precipitate the dissolved constituent in a dispersed condition. This results in an increased resistance of the alloy to deformation with an attendant improvement in the tensile properties.

Jan 1, 1929

APPROXIMATELY 90 per cent of the steel that is melted and refined in the United States and poured into ingots is made in basic open-hearth furnaces, as shown in Table 1-1. The annual ingot capacity of the steel industry reported January 1, 1950, by the American Iron and Steel Institute3* was 99,040,160 tons, of which the basic open-hearth process accounted for 85,896,580 tons, 86.7 per cent of the .total. The capacity of the individual furnaces varies over a wide range, a large majority falling within limits of 50 to 200 tons (Fig 1-1). Most of the units constructed [ ] since 1942 are in the larger size groups, between 175 and 225 tons capacity.

Jan 1, 1964

By Morgan Walker

Intermittent injection of gas in gas-lift pumping is a variation of the common practice in that the gas is delivered to the well for a short period, called the "on time," followed by a period during which none is admitted, called the "off time," instead of being admitted continuously at a constant rate or by intermittent flowing in which it is occasionally delivered to the well in just sufficient quantity to flow off the accumulated head of fluid. The term "gas" is used throughout this discussion but it should be remembered that in so far as the operation is concerned either air or natural gas may be used. The equipment at the well is the same as commonly used in gas-lift installations and gas may be admitted to either the tubing or the casing. It seldom occurs that all the wells on a lease can be pumped economically by intermittent injection from one header. Wells that have flow characteristics which permit their being handled together have their intake lines grouped at a central compressor station. Well groups may consist of two or more wells. The total volume of gas delivered by each group of compressors goes to one well at a time through a quick opening valve, each well connected to the header receiving its charge of gas in turn. Special cases may require a deviation from this arrangement. The distribution of the gas to the different wells is effected by an automatic timing device which operates quick-opening valves on the intake lines. The timing mechanism may be actuated by electricity, liquid or gas pressure, The essential factor in the operation of the timing mechanism is that as one intake valve is closed another must be opened. Water-operated Timing Device Timing devices operate the intake valves either directly, or indirectly by pilot valves. Of the former type one that is operated by water and has given satisfactory service is shown in Fig. 1 and can be made on the lease. The horizontal cylinder is a piece of 10-in. casing about 7 ft. long, closed at each end and free to oscillate about a fulcrum at the center.

Jan 1, 1929

By Frederick C. Hull, Robert F. Mehl, Robert A. Colton

IT is known that pearlite forms from austenite by a process of nucleation and growth, and that the rate of formation of pearlite may be described by a rate of nucleation and a rate of growth.1,2 The manner in which these two quantities operate to produce the observed isothermal reaction curve has been analyzed in a paper published in 1939.3 Two types of process were described: (1) that in which nucleation occurs at the grain boundaries of the parent phase, with the nodules growing toward the centers of the grains, initially as hemi¬spheres and then after impingement as roughly radial-columnar structures; and (2) that in which nucleation occurs generally, with the nodules growing to full spheres until impingement with other growing nodules restricts growth. Both cases are met in the formation of pearlite from austenite (Fig. 1);2.4 the former, occurring near the knee of the S-curve has been named "grain-boundary transformation," and the latter, occurring at temperatures near Ae1, has been named "group-nodule transformation." In developing our knowledge of the factors that determine the rate of formation of pearlite from austenite, it is important 1,2 to obtain data on the rate of nucleation and the rate of growth of pearlite. Such data, when obtained near the knee of the S-curve, will furnish information of use in understanding the factors that affect hardenability; when obtained at higher temperatures, such data will be useful in understanding the behavior of steels that during heat-treatment react to pearlite.2 It is the purpose of this paper to present data on the rate of nucleation and the rate of growth of pearlite in dependence upon composition, grain size, temperature, and the degree of homogeneity of the parent austenite. The studies are restricted chiefly to plain carbon commercial steels.* PREVIOUS DATA ON RATE OF NUCLEATION AND RATE OF GROWTH Data on the rate of nucleation and the rate of growth of pearlite have been published by Scheil and Lange-Weise,5 by Mirkin and Blanter,6,7 by Mehl,1 and by Dorn, De Garmo and Flanigan.2 It is difficult to interpret the data, for in most cases too little information is given on austenitizing temperatures and times, the state of homogeneity of the austenite (presence or absence of carbide, etc.), austenite grain size, and mode of formation of pearlite at the temperatures given.

Jan 1, 1942