Search Documents

By J. Rourke, F. S. Minshall, E. G. Zukas, C. M. Fowler, O&apos

The Hugoniot curves were determined for Fe-Si alloys containing up to 7 wt pct (13 at. pct) Si. The pressure of the transition increased as the silicon content of the alloy increased. Single crystals of 2.9 wt pct Si-Fe were also studied. The pressure of the transition was not dependent on crystallo-graphic orientation. All of the Neumann bands (mechanical twins) were attributable to (112) planes but not all of the {112} planes showed twin markings. A thorough study of the iron Hugoniot (the relationship between specific volume and pressure) under plane wave shock loading revealed a pressure transition at about 130 kbar shock pressure. The results of this investigation were reported by Bancroft, Peterson, and inshall1 in 1956. At the time of this discovery, it was felt that this was probably the a, to y transition normally found in iron and many of its alloys. Subsequently a number of iron alloy systems were surveyed in which the alloying element has a considerable effect on the normal a, to y transformation. The influence of carbon and nickel and/or chromium have already been reported.2,3 At the present time, there appears to be some doubt that this pressure transition is the usual a, to y transition In this study, Fe-Si alloys containing up to 7 wt pct (13 at. pct) Si were chosen for several reasons. To the present, the transition has been found only in iron-base alloys which were originally in the a, phase (bcc). Secondly, the y loop at atmospheric pressure extends to only about 2.5 wt pct Si. If the transition were a, to y, then one might expect a rather drastic pressure effect for alloys containing more than 2.5 wt pct Si. Finally, single crystals of Fe-Si alloys large enough for shock loading studies are readily available thereby making it quite easy to determine the effect of crystal orientation on the transition pressure and on the twinning behavior of the alloy. EXPERIMENTAL PROCEDURE Fe-Si alloys containing up to 7 wt pct Si were produced by normal vacuum casting procedures. Single crystals of Fe-2.9 wt pct Si were purchased from Monocrystals Co., Cleveland, Ohio. The orientations of these crystals were determined and samples cut so that the shock wave would be parallel (to within 1.5 deg) to either the (loo), (Ill), or (112) principal orientations. Three distinct experimental testing techniques were used. First, the pin technique, described elsewhere,4 was used to determine the transition pressure for the polycrystalline alloys as well as for the (111) and (112) orientations of the 2.9 wt pct Si single crystals. Secondly, the recovery studies, described in detail in an earlier paper,2 were used for determining the effect of alloy composition and crystal orientation on the plastic II compression-plastic I rarefaction interaction zone for several specific shock pressures. Finally, measurements of pressures above the two-wave threshold were made on the polycrystalline alloys so that more complete Hugoniot curves could be constructed for this alloy system. The optical techniques described by Rice et al.5 were used to measure the shock and free surface velocities of the samples from which the Hugoniot data were obtained. This method is applicable only in the single wave region, since velocities are obtained from the measured total transit times of the disturbances through measured sample thicknesses.

Jan 1, 1963

By K. A. Svanstrom, W. R. Opie

Problems associated with deposition of titanium infused chloride baths using TiCl4 as a feed material are reviewed. A potentially workable cell design using Alumdum diaphragms is discussed. Problems inherent to diaphragm-type cells are emphasized and experiments described which led to the development of a cell without a diaphragm. INVESTIGATORS assigned the problem of developing a commercial electrolytic process for making titanium metal have found that they are faced with the difficulty of overtaking rapidly improving magnesium and -sodium reduction processes. The ultimate goal must be a simple process that can be conducted with low-cost raw materials in equipment that is inexpensive to build and operate. This paper deals with some work of a preliminary nature conducted by personnel of the Research Laboratories, National Lead Co., Titanium Division. Many others have reported on the general subject of depositing titanium from fused salt electrolytes. A partial bibliography is attached. PRIMARY CONCEPTS Anyone attempting to deposit titanium metal from fused chloride electrolytes using TiC14 as a source material is faced with at least the following problems: 1) Getting the titanium into solution in the bath. 2) Controlling oxidation and reduction reactions associated with multiple valency of titanium, which result in low electrical efficiency. a) Prevention of dichloride oxidizing to trichloride and trichloride to tetrachloride at the anode. b) Prevention of trichloride from being reduced only to dichloride at the cathode. 3) Prevention of metal formation away from the cathode thru disproportionation of titanium dichloride to satisfy the equilibrium. 3 TiCl2 == 2 TiCl3 Ti [I] 4) Protection of reduced chlorides in the bath from reaction with oxygen from the bath container or air. 5) Removing from the bath the deposited metal formed without allowing it to become contaminated with oxygen or nitrogen. 6) Selecting cell materials of construction which will not contaminate the metal product or cause cell inefficiencies. EARLY EXPERIMENTS The initial attempts made to electrodeposit titanium from fused chloride baths using TiCl4 as a source material indicated that TiCl4 was essentially insoluble in molten chlorides of alkali and alkaline earth metals. If, however, the TiCl4 was introduced close to a nickel cathode some metal could be formed and appreciable quantities of reduced chlorides would be present. These reduced chlorides reacted with any oxygen present in the atmosphere above the bath and would also diffuse quickly to the anode (graphite) where they would react with chlorine and be evolved as TiCl4. The net electrolytic efficiency of such a cell is essentially nil. The TiCl4 evolves from the anode at almost the same rate that it is introduced in the vicinity of the cathode although a small amount of titanium metal can be formed on the walls of the cathodic pipe. It becomes apparent from the operation of such a cell that: metal can be deposited on the cathode, although of small particle size and a nonadherent nature, and when reduced chlorides are present in the electrolyte, TiCl4 can be absorbed, probably by the following reactions: TiCl4 + TiC12 - 2 TiCl3 [21 2 TiCl3 + 2 faradays - 2 TiC12 + C12 [31 DIAPHRAGM CELLS These facts encouraged the development of cells containing diaphragms to prevent migration of reduced chlorides from the cathode area to the anode. Small-scale cells for process development are described by Alpert, Schultz, and Sullivan.20 A larger brick-lined cell incorporating internal heating by passing ac through the bath is shown in

Jan 1, 1960

By Tony B. Szwilski, K. Unrug

INTRODUCTION Since the introduction of longwall coal mining systems, reliable predictions of roof support requirements at the face and the roof caveability in the gob area have been major contributors to the success of the longwall face by means of safety and face productivity. That is, the successful operation of a longwall is well-served by good regular caving of the gob. In recent times, with the advent of increased coal face mechanization and capital investment, the evaluation of the feasibility of longwall mining has become essential. In the United States, where a face unit for a face length of about 150 metres may cost around $6 million, a quantitative system that would assist in selecting the best equipment for the coal would prove extremely beneficial. There have been many such varied investigations in the past few years. A vast -amount of work has been invested principally by West Germany [3, 7, 8, 91 , Poland [I, 101 , United Kingdom [4, 5, lo], France [4], and South Africa [4]. It is the object of this paper to review this previous research work and give an outline that may be used as guidelines for long- wall evaluation. Essentially, for the initial design phase for a longwall system, account must be taken of the geometry of the coal panel, its position relative to the surface (depth), direction of the coal cleat system, faults and in-situ stresses and other neighboring workings in the same coal seam and other seams both above and below. The advance of the coal panel disturbs the stress field and in doing so creates an abutment zone around the face. At this stage the condition of homogeneity of the surrounding rock mass does not apply. The magnitude of the rock strata pressure may exceed the ultimate strength of the rocks and create zones of clastic, plastic and elastic material, the limits of which are difficult to determine. The collapse of the gob and resulting expansion of the displaced waste roof rock, create a statically undefined support complicating an already unclear rock structure. For example, it is often a point of debate whether, indeed, the vertical strata pressure develops to regain the original magnitude of virgin stress. Under these post-failure circumstances an analytical approach based on simplified and idealized assumptions can only be considered a very general approximation. Theoretical concepts, however, may be adequately supplemented by empirical methods that are based on numerous underground observations and surveys [3, 4, 7, 8]. These methods employ the use of rock indices that very handily correspond to the competence of the roof rock mass. Scale model work [3, 41 , using equivalent materials representing the surrounding rock mass within the coal seam zone, have given valuable qualitative and sometimes quantitative data in addressing the behaviour of the rock mass around longwall panels. To characterize the state of art of caveability predictioqthe principal concepts will be reviewed with special emphasis placed on practicality for the planning of longwall operation. It has been the general observation of the authors that many of the literature surveys published in English often neglect reference to other international mining literature. It is with this point in mind that an overall review has been written including mining concepts identified with the principal coal mining countries. THEORETICAL CONCEPTS Arching Theory For the development of this theory, assumption has been made that an extracted height, h, in a coal seam results in an extracted panel of width, w . Also, the coal seam is horizontal and the rock strata of both the roof and floor are homogeneous. The primary (virgin) stress distribution will change in the roof as well as the floor. As a result of lack of support caused by the excavation (in the gob area) an additional load is developed due to the redistribution of the load around the sides of the panel, referred to as the abutment, R, where: [ ]

Jan 1, 1982

By Alden B. Greninger

Many recent contributions in the field of theoretical metallography have been concerned with crystallographic definitions or descriptions of various phenomena. The lattice orientation of the crystal being studied must be known before such definitions can be made. Practically all the metallic crystals used do not have crystal faces—other than the unknown "plane of polish"; hence resort must be had to other means of determining orientations. Some use has been made of etch-figures, slip bands, optical properties, etc., for this purpose; but for accurate results, and because of the fewer restrictions to their use, the various X-ray methods have been the most satisfactory.' The methods that have been used may be divided into two general classes: (1) oscillation methods, and (2) transmission Laue methods.² The disadvantages of these methods are numerous, chief among them being the time required to determine a complete orientation. No method proposed so far is wholly satisfactory for determining the orientation of a small macrograin within a polycrystalline aggregate.

Jan 1, 1935

By Alden B. Greninger

Many recent contributions in the field of theoretical metallography have been concerned with crystallographic definitions or descriptions of various phenomena. The lattice orientation of the crystal being studied must be known before such definitions can be made. Practically all the metallic crystals used do not have crystal faces—other than the unknown "plane of polish"; hence resort must be had to other means of determining orientations. Some use has been made of etch-figures, slip bands, optical properties, etc., for this purpose; but for accurate results, and because of the fewer restrictions to their use, the various X-ray methods have been the most satisfactory.' The methods that have been used may be divided into two general classes: (1) oscillation methods, and (2) transmission Laue methods.² The disadvantages of these methods are numerous, chief among them being the time required to determine a complete orientation. No method proposed so far is wholly satisfactory for determining the orientation of a small macrograin within a polycrystalline aggregate.

Jan 1, 1935

By Prince Gelasio Caetani

PRESIDENT DWIGHT'S invitation to be a guest of the American Institute of Mining and Metal-lurgical Engineers was the first of the subsequently very numerous invitations to dinner I have received from my American friends. When I received his telegram I had not yet been even formally appointed Ambassador. I cannot tell you how deeply I appreciated it. It was a hearty welcome in returning to your country which has been for me a second home and it came from the American mining brotherhood which has been my second family.There are two distinct periods of learning in life. The first one are the years spent in school where we learn many things we after-wards forget; the second one are the years of prac-tical apprenticeship which engrave indelible signs in a man's character and shape his life. These latter years I spent in the United States and they have influenced the whole course of my life. I owe very much to my American friends who trained me. The earliest was Prof. Robert Peele, of Columbia University. At the Daly West mine, in Park City, Utah, he curbed my futuristic English spell-ing and had a hard time at it. Prof. James F. Kemp taught me that geology is a guess work just as unre-liable as the prediction of international events; he taught me also that a frank, honest and loyal character will lead a man equally straight through a mining report and through public life.

Jan 3, 1923

By V. Apraxine, J. Lakaye, J. J. Saquet, P. Troch

Union Minière du Haut-Katanga owns concessions for extracting copper and associated metals in the high plateau region of Katanga. The concession is about 188 miles long by 44 miles wide and has three principal areas: Southern area-The Prince Leopold mine is an underground operation from which a copper-zinc sulfide ore is extracted. The mine and associated concentrator are at Kipushi. Copper concentrates are smelted and converted to blister copper at the Lubumbashi smelter at Elizabethville.

Jan 12, 1962

By Basil Prescott

A thorough knowledge of the peculiarities of this type of orebody is necessary in sampling these limestone replacement deposits. Oxidized ores are often overestimated because of error in determining specific gravity and actual cross-section of the orebody, and sulfide ores are often underestimated because it is difficult to scatter the samples so that they will accurately represent the area under consideration. This paper describes various methods of sampling and cites factors that enter into the estimation of these deposits. IN THE science of evolution of the species, there is a law which, simply stated, avers that the history of the individual repeats the history of the race. Similarly, if unassisted by the experience of others, each successful engineer would perfect and develop his methods and technique from the rough grab sample up to the carefully taken, recorded and studied samples and observations which now determine and decide the expenditure of the large sums required for modern mining. Hence real progress results from the interchange of experience, as in that way the entire experience of the profession can be made available to every engineer. The literature of this subject is already voluminous, but some progress has been made in the gathering of data and in their compilation or presentation.

Jan 3, 1924

By Louis D. Huntoon

After the completion, in 1905, of the Hammond Mining and Metallurgical Laboratory of the Sheffield Scientific School, Yale University, it became necessary to secure and assay a large assortment of ore-samples, and to arrange the results in such a manner as to admit of use with the least amount of work on the part of the instructor. At first, pulp-samples, together with their respective assays, were secured from the mines, smelters, and public aesayers, but this practice did not prove satisfactory. It was not only difficult to secure a suffciently large supply of material, but it was also impossible to secure the proper assortment required for instructing students. It involved considerable work for the donors to select the samples and furnish a record of the assays, and also for the instructors to examine each pulp and determine its character. Some of the samples did not contain a sufficient quantity of pulp for the student to check his work in case his first assay did not correspond to the record. In order to increase the number of samples and to vary the character of the material, pulp-samples were later mixed with barren rock and with sulphides, but this method also was unsatisfactory and has been discontinued. At present, small lots of ore are secured by gift or purchase from engineers, public assayers, and the managers of mines, mills, and smelters. These lots weigh from 10 to 100 lb. each, and are rarely finer than 0.25 in. in size. The larger samples permit of a careful study by the instructor in order to determine the best method of assaying to be followed. In universities in which assaying is taught the record of the samples should fulfill the following requirements:

Jan 1, 1910

By A. B. Bowman

The 1963 Jackling Award lecturer describes the founding of Banner Mining Co. and its trials and tribulations before becoming an established firm. Such aspects as geological description of Banner mining areas, history of exploration and production, areas of present interest to the company and research work conducted by the company are included. Several years ago a wealthy Chinese business friend of mine purchased an interest in a proposed oil well to be drilled a great distance from his home. A few months later it came in as a producer and proved to be a huge success and materially added to his resources. I asked him why a man of his wealth should be so lucky in a venture outside his sphere of knowledge when most people of modest means never seemed to get ahead. His answer was, "Fat Hoy takes a chance." Even though this was his answer, I knew from my association with him that there were other tempering considerations which Mr. Hoy applied before making up his mind to enter any transaction. First, he was a cautious individual. He was also a great believer in details and insisted on knowing everything possible about a situation, and finally, he was what we call a very solid individual with good basic instincts and judgment. This philosophy of Mr. Hoy may be applied to most any business but especially to those engaged in a search for natural resources such as mining where great risks are involved. This article concerns events in the history and growth of Banner Mining Co., with which I have been associated for 27 years in capacities from mine surveyor to vice president. Mr. Hoy's philosophy has played a significant role in the exploration projects of this company over the years, but what is more important, the officers, directors, and controlling interests in Banner have been aggressive in their search for ore reserves. THE BIRTH OF BANNER Banner Mining Company was incorporated in September 1935 by a group of Oklahoma and Texas oil men for the purpose of exploring and developing the Bonney-Manilla mines at Lordsburg, N.M. These properties had a history of intermittent production since the first ore discoveries as far back as 1870. Most of the production from the district has come from four mines, namely, the Eighty-Five, the Atwood, the Bonney-Manilla, and the Misers Chest. The last two are now owned by Banner Mining. The Eighty-Five mine operated between 1885 and 1931, and production totalled 1,494,287 tons averaging 0.11 oz of gold per ton, 1.23 oz of silver per ton, and 2.80% copper. The vein extended for a distance of about 3000 ft northeast and was mined to a depth of 1650 ft. The Atwood mine, adjoining the Eighty-Five mine, to date has been of lesser importance as a producer, but it has been operating for several years producing high silica flux ores for a smelter. Production totalled 352,828 tons up to January 1, 1962 From the Bonney-Manilla and Misers Chest mines, owned by Banner, production through 1961 totalled 2,006,343 tons with an average grade as mined of 0.0192 oz of gold per ton, 0.760 oz of silver per ton and 2.63% copper. Banner built a 150-tpd flotation mill in 1936 after almost a year of development on the 600 level of the Bonney mine. After less than one year's operation, it became apparent that the 150-tpd rate was not sufficient to make a reasonable profit due to the marginal grade ores. The low tenor of the ore, mainly chalco-pyrite in a highly siliceous gangue, made mandatory the close control of costs in order to make ends meet. A 300-tpd unit was added to the mill in 1937, and it is still the operating unit today. The clean sulfides presented no problems in milling. A metallurgist doing research on it at the time stated that the copper minerals seemed to have a built-in desire to float. Mill recovery of copper throughout the 27 years of operation has averaged 96.23%. A PERIOD OF FORCED GROWTH World War II brought many hardships to Banner. Labor and supply shortages caused drastic curtailment in development work. Rapidly rising costs far outdistanced any relief from pegged prices which we received from Government agencies. Finally, a branch of the Government asked us to stop all devel-

Jan 1, 1963

By R. H. Harrington

THE definition of precipitation-hardening is well understood and its principles have been subjected to study for some time. However, the variation of properties with double aging, combined with strain-hardening, gives promise of new and useful phenomena. Properly to understand these distinctions, definitions of these terms are necessary. Precipitation-hardening. This reaction usually depends upon an alloy having such a composition that it consists only, or in major part, of but one phase, a solid solution, at a high temperature, so that, upon slow cooling, this solution breaks down into two phases, the solid solution and a compound. By heating the alloy to the temperature for maximum solution of the compound, quenching, and reheating to a suitable lower temperature for critical dispersion precipitation of the compound, useful properties of the alloy may be developed to a maximum. Double Aging.-Dougle aging in part is similar to the process for precipitation-hardening, consisting of heating a precipitation-hardening alloy to the solution temperature, quenching, reheating to the suitable dispersion precipitation temperature, strain-hardening, and again reheat-ing to a suitable temperature to develop certain useful properties to a maximum. The strain-hardening may be induced by two methods: (1) a rate of cooling from the first reheat may suffice to strain the solid solution lattice of the alloy; or (2) the alloy may be cold-worked to a suitable degree between the two reheats.

Jan 1, 1936

By M. J. Marcinkowski, A. Szirmae, R. M. Fisher

Room -temperature hardness measurements obtained from single and polycrystalline samples of a 47.8 at, pet Cr-Fe alloy which were aged for various times al 500°C show a two-fold increase over that of the unaged alloy after annealing for 1000 hr. A detailed examination of the deformation markings in the neighborhood of the hardness imbressions reveals that twinning becomes an increasingly more important mode of deformation as aging proceeds. this observation is shown to be inconsistent with the Proposals that the transformation is eve of order-disorder On the other hand, the results are in agreement with previous observations of Fisher et al. of a coherent chromium-rich precipitate which forms in an iron-rich matrix as a result of a miscibility gap in this alloy system as proposed by Williams . Using the coherent precipitate hypotlzesis as a model, a detailed analysis of the various possible strengthening contributions to both the slip mid twinning stresses is made. In the case of' slip, lattice friction within the chromium-rich phase and the chemical energy associated with the interface between the two phases contribute about 60pet to the total strength. The contributions from coherency strains and modulus differences are thought to contribute the remaining 40 pet of the strength but are difficult to evaluate because of uncertainties regarding the flexibility of the dislocation line. All of the factors have nearly the same or else a smaller effect on the twinning stress in the aged alloy. Twinning is never observed in the unaged alloy because the twinning stress is much higher- than that for slip. With increased aging times, the various contributions to the total stress for both twinning and slip increase, but most of those for slip increase much more rapidly, so that, in the fully aged alloy, it surpasses the stress for twin propagation. When a twin is nucleated by the chance occurrence of an internal stress concentration during a test, the subsequent twin burst results in a low hardness reading. FeRNTIC Fe-Cr alloys from about 15 to 80 at. pet Cr content show considerable change in properties such as hardness, electrical resistivity, saturation magnetization, and so forth, after aging in the vicinity of 500°C.* The most marked change is a large increase in hardness accompanied by a sharp decrease in ductility, so the phenomenon has often been referred to as the 475°C (885°F) em-brittlement problem. Changes in microstructure are rather subtle and most investigators have not been able to observe any X-ray diffraction or metal-lographic changes during aging. There is little doubt that the phenomenon is inherent to the Fe-Cr binary system and is not directly related to the formation of a phase. Two distinct schools of thought have developed during the past decade concerning this problem. Masumoto, Saito, and sugiharal have concluded, from their own specific-heat measurements, that atomic ordering occurs in this temperature range. Pomey and Bastien2 have also attributed the changes in physical properties with aging in the neighborhood of 500°C to atomic ordering. In addition, Takeda and Nagai3 claimed to have found X-ray verification for superlattices corresponding to the compositions FesCr, FeCr, and FeCr3. However, all known attempts to observe superlattices in Fe-Cr alloys using neutron diffraction, which should be much more sensitive, have been unsuccessful. These have been reported by Shull et al.4 for 25 at. pet Cr, williams5 for 75 at. pet Cr, and Tisinai and samans6 for a 28.5 at. pet Cr. steel. The second and more prevalent opinion ascribes the 475°C embrittlement phenomenon to the formation of a coherent precipitate due to the occurrence of a miscibility gap in the Fe-Cr system below about 550°C. This latter concept was first indicated by the results of Fisher, Dulis, and Carroll,7 who were able to extract fine particles about 200Å in diameter from samples of 28.5 at. pet Cr steels aged from 1 to 3 years at 475°C. The extracted material was found to be nonmagnetic, to have a bee structure with a lattice parameter between that of iron and chromium, and to contain about 80 at. pet Cr. Williams and paxton8 and williams5 confirmed these results and first explicitly proposed the existence of a miscibility gap below the a region in the equilibrium diagram. Alloys aged within this gap

Jan 1, 1964

By Thomas L. Garrard, James A. Sprague, Rex B. McLellan, Samuel J. Horowitz

A simple rnodel for interstitial solid solutions has been devised in which each solute atom interacts with the solzlent lattice in such a way as to exclude an integral number of nearest-neighbor sites from being occupied by solute atoms. The vemaining interstitial sites ave not affected. In calculating the entropy of such a solution the increase in the number of interstitial sites available to solute atoms due to the ozlerlap of blocked sites is taken into account. The ther-modynamic functions and the solute activity fov the solution rnodel are calculated. It is shown that considevation of the overlap sues vise to a correction term of the order 8' ( where 0 is the ratio of solute to solvent atoms) in the thevmodynamic functions of the solution and the solute activity. The theo,uetical equation for the solute activity was used to analyze the available data for the activity of carbon in austenite at three different temperatures. The use of a computer enabled many comparisons to be made between the experimental activity data and those predicted by both the complex blocking model and the simple, widely used blocking model in which the ozierlapping of blocked sites is not taken into consideration. Even though at the highest concentvations oj carbon the value of 0 is small it is shown that the best fit to the experimental data is found with the complex blocking model. RECENTLY it has been shown by analysis of gas-solid equilibriums that many interstitial solid solutions can be described by the quasi-regular solution model in which the partial energy of solution E, is independent of composition and, apart from a composition-independent term due to nonconfigurational factors, the partial entropy is that of an ideal solution. Dilute solutions of nitrogen in both bcc and fcc iron,' dilute solutions of oxygen and silver,' carbon in a Fe,' and dilute solutions of carbon in ? Fe2 are all quasi-regular. In addition many hydrogen-metal solutions, both dilute and concentrated (with the notable exceptions of the H-Ni and H-Pd systems), can be described by this model.3 However, it has been shown that, at various temperatures, solutions of carbon in ? Fe begin to depart strongly from quasi-regular behavior at low concentrations. A plot of the activity of carbon in ? Fe relative to pure graphite vs atom fraction of carbon (Cc) calculated from Smith's data4 begins to depart from the (nonlinear) plot for a quasi-regular solution at about Cc = 0.02. Several statistical models have been proposed to account for the thermodynamic behavior of carbon in y Fe. Darken and smith4 set up a model in which a carbon atom in its octahedral site in the fcc lattice has either one or no neighboring carbon atoms in the twelve nearest-neighbor octahedral sites. It is assumed that the number of carbon atoms having more than one nearest neighbor is negligibly small and that a solute atom does not interact with another solute atom located at a greater distance than the first shell of interstitial sites. Thus this model contains two characteristic interaction energies. Darken and Smith showed that this model gives reasonable agreement with the measured variation of carbon activity ac with composition. It is noteworthy that Darken and Smith concluded from their analysis of the activity data using this model that there was a repulsive force between carbon atoms in austenite which reduces the concentration of C-C pairs below that corresponding to random mixing. Recently Aaronson, Domian, and pound5 have considered in detail the statistical model developed by Lachere and by Fowler and Guggenheim7 and have shown that it is compatible with the activity data for carbon in austenite. In Darken's model the energy of solution of carbon in austenite is dependent on temperature and concentration; the departure from Henry's law arises from the concentration dependence of the energy of solution. In Aaronson, Domian, and Pound's discussion of the Lacher, Fowler, Guggenheim model the interaction energy wy between adjacent carbon atoms in austenite is strongly temperature-dependent. Aaronson et al . suggested that this temperature dependence of wy and hence the energy of solution of carbon could be explained either by the formation of clusters of carbon atoms (despite the repulsive nature of wy) or by the dual occupancy of the octahedral and tetrahedral sites by the carbon atoms. However, a temperature-dependent heat of solution

Jan 1, 1968

By D. R. Uhlmann, T. P. Seward, K. A. Jackson, J. D. Hunt

microscopic ohservations on alloys of organic trzaterials show that dendrite arms can melt off under normal conditiorzs of growth. This occurs because of the interactiorz of' heat and matter fluxes during dendritic growth. The re melting occurs where the den-drite arms are joined onto the main deizclrite sterrz. Many detached crystals can be produced in this fashion. It is postulated that this remelting phenornenon occurs in metal alloys, giving rise to the equi-axed region in castings. Experiments peyformed orr castings of transparent materials support remelting as a primary source of detached crystals. Ob~ervations an equiaxed tones in metal castings are discussed in terms of this and other mechanisms. It is concluded that the partial remelting of dendrites is on important mechanisnl for producing the equiaxed regions in castings. THE freezing of a casting can be divided into three regions: a chill zone formed near the mold wall, a columnar region, and a third region, at the center of the casting, which is called the equiaxed zone. The origin of the grains that comprise the equiaxed region is the subject of this paper. We will first outline the mechanisms which have been proposed to account for the origin of the equiaxed region and discuss some recent experiments which cannot be explained by these theories. We will then present some microscopic observations of dendritic growth which have led us to conclude that the equiaxed zone in castings can arise from partial remelting of dendrites. This proposal is supported by observations on transparent castings. Finally, we will discuss several observations on metal castings which could not be explained previously, and which can be accounted for by the present proposal. Previous Mechanisms. Winegard and Chalmers3 pointed out that the molten central region of an ingot could be constitutionally supercooled, because of the solute layer at the growing interface. In this supercooled region, nucleation on particles could occur, giving rise to the equiaxed crystals. Another mechanism has also been suggested,4y5 that the nuclei originate in the chill zone then float or are carried by convection to the center of the casting, where they grow to produce equiaxed crystals. In this case, all the crystals nucleate immediately on casting, so this mechanism will be termed "big-bang" nucleation. Walker's Experiments. J. L. Walker has made observations on the solidification of nickel and Ni-Cu alloys which cannot be accounted for by either of the above mechanisms. In studying the grain size resulting from freezing of nickel at various undercoolings, walker6 found that at large undercoolings the grain size was small, due to mechanical nucleation, as discussed by walker7 and Horvay.' At small undercoolings, the grain size was large, and the growth dendritic. In Ni-Cu alloys, however, for initial undercoolings starting from just below the melting point and extending for a hundred or so degrees of undercooling, fine grains were also observed. Samples were undercooled 200 Centigrade degrees without nucleating, and were then heated 130 Centigrade degrees so that the undercooling was 70 Centigrade degrees, and nucleated. The samples had a small grain size, indicating multiple nucleation. There were no heterogeneous nuclei in the liquid which could operate at the temperature of growth. Constitutional supercooling could not have been greater than the supercooling of the initial melt, since the temperature rose as the freezing continued. walker -as also shown that a Ni-Cu alloy which can be undercooled to below its solidus will produce typical columnar and equiaxed regions when cast into a cold mold. This alloy could not reach a temperature below its solidus by constitutional supercooling. It could not, therefore, have nucleated heterogeneously. Neither the big-bang mechanism nor the Winegard-Chalmers mechanism can account for the fine grain

Jan 1, 1967

By E. W. Enqelmann

DURING January, 1933, burlap or coco matting was placed in the bottom of launders handling various products of the flotation plant of the Magna mill of the Utah Copper Co., with the hope of increasing the total recovery of gold. This was soon followed by placing various materials, such as coco matting, cotton twill, and common 10-oz. burlap on the bottom of the main tailing launder. The burlap was found to be the most economical material to use. The test was first conducted in an old wooden launder, 40 in. wide and 2000 ft. long, with 10-oz. burlap fastened

Jan 1, 1935

By Marcus Grossmann

THIS paper offers for consideration certain somewhat radical modifications in the iron-carbon diagram, these modifications being the result of the presence of notable amounts of alloying elements. When only small amounts of alloys are present, 'the standard iron-carbon diagram (Fig. 1) can be used with but insignificant changes; when larger amounts of Chromium, Per Cent FIG. 1.-IRON-CARBON DIAGRAM. FIG. 2.-IRON-CHROMIUM DIAGRAM. alloys are present, however, it assumes a distinctly altered appearance. No comment is offered for the present except to call attention to the delta area, A4BM, which represents a region of mixtures of austenite and delta iron, just as area A3SP represents mixtures of austenite and alpha iron.

Jan 12, 1926

By D. W. Gillmore, C. C. Wright

DEWATERING is a major problem in the preparation and utilization of fine-sized coals now being recovered in increasing amounts from colliery effluents, refuse banks, and silt ponds. Of the various methods which have, been proposed for dewatering fine coal, gravity drainage is probably the oldest and most widely used, and yet little information on this subject has been published. Consequently a laboratory investigation of gravity drainage phenomena was undertaken not only to provide basic data for predicting the drainage behavior of fine coals in cars, bunkers, basins, and silos, but also to obtain some understanding of the moisture retention properties of fine coal. Because of practical interest in the problem, a reproducible laboratory technique, which simulated plant conditions as closely as possible, was developed for the evaluation of drainage variables. The ap- paratus selected consisted of vertically-mounted lucite columns, nominally 4 to 8 ft in length and 2, 3 or 6 in. in diam; the bottom of the column was provided with a rubber stopper through which was inserted a -in. diam drainage tube; a wad of glass wool was placed on the upper part of this outlet tube to retain the coal and a plug was temporarily located at the lower end to prevent drainage during charging of the column, see Fig. 1. The most satisfactory testing procedure is as follows: 1—The fine coal, which has been thoroughly

Jan 1, 1953

By W. H. Meyer

During the seventeen years Fairchild has been making aerial surveys and aerial photographic equipment many changes and improvements have been made in the equipment and in the technique of using it. Aerial photographic operations have been developed from the crude methods and apparatus of wartime to a science upon which exact engineering calculations can be based. In the early days there was no airplane specially designed to meet aerial photographic requirements. One type of camera was used in all types of operations. Projects were made to conform to the products we could make and deliver. Obviously this entailed definite limitations. We now have airplanes designed specially for aerial photographic operations in accordance with the conditions encountered in actual service experience. We have cameras for every photographic purpose and our laboratory technique and equipment have been developed to the point where it is possible to make contour maps from vertical aerial photographs with contour intervals as close as five feet. Therefore, the selection of equipment now can be made in accordance with the time at our disposal, the justifiable cost, the scale desired, and the general requirements of the client. This does not mean, however, that arbitrary deliveries can be set for aerial photographic products. The factors in each project vary and each job must be considered in accordance with the factors involved. This accounts for the fact that products of aerial surveys may readily vary from $1.25 to $200 a square mile. Sherman M. Fairchild became interested in the design of a radically different aerial camera during the war. At its close he was about ready to demonstrate his design to the War Department. By 1920, he was able to bring out his first completed model. It had a number of radical features, one of which was the first dependable high-speed between-the-lens shutter, which makes for accuracy in aerial photographic work. Another feature was the use of metal throughout, eliminating the wooden parts that had been employed in wartime cameras. Another feature was the interchangeability of parts.

Jan 1, 1937

By Arthur A. Brant

Let us start back as far as possible, to the beginnings of this universe, some 5 billion or more years ago. This is a time interval that can be crudely underestimated by the moon-earth tidal friction effects that have increased the length of the day by about 1/1000 second per century-from a 5 to 7 hour day to its present 24-and have moved the moon away at 5 inches per year to its present 240,000 miles. The oldest stony meteorites from interplanetary space give an age dating of some 4.6 billion years, approximating the time of formation of our earth. Further, certain stars pulsate, the period of pulsation being related to their absolute brightness. Measuring apparent brightness and comparing, gives the distance away. Thus Hubble and Shapley of Harvard, from 1925 on, were able to show that the universe reached as far as our telescopes could scan. The Doppler shift of the hydrogen red lines could only mean that the nebulae, or galaxies, were moving away at velocities increasing with their distances, by 180 km/ sec velocity increase for every million light year's distance. In short, the universe is expanding like an exploded bomb.

Jan 4, 1964

By Wido Tilmann

13.6-1. Importance. In Germany there are large tertiary brown coal reserves, most of which are located close to the surface. Therefore, brown coal has been recovered for many years by means of opencast methods. By utilizing a high degree of technology, a rational operation has been achieved, and as a result, the mining techniques have become renowned all over the world. After the war, all the dredgers and overburden spreaders, as well as the means of conveyance, had to be redeveloped for adapting this equipment to the changing conditions of the deposits. Numerous auxiliary machines were adopted from the American earth moving industry and altered according to the different requirements. As a result of such technical developments, the output per man and per shift was increased remarkably in spite of the deterioration of the geological conditions. In the whole of Germany, the total reserves of brown coal amount to 100 billion metric tons, of which 60 billion tons are situated in the Federal Republic of Germany. In the latter area, 8.5 billion tons will be recover- able by opencast means, of which 3.5 billion tons are already developed. The annual output reached 102 million tons in 1965. This total figure comes from four different mining districts: Rhineland, Helmstedt (town at the border of the Soviet occupied zone), Hesse, and Bavaria. The production figures (1965) are as follows: [ ]

Jan 1, 1968