Search Documents

By W. A. Tiller, J. D. Harrison

HOT pressing of powder particles has gained importance recently, since it affords a method in which high densities are rapidly attained. In a recent study on hot pressing of alumina powders, Mangsen, Lam-bertson, and Best1 have shown within the limits of their experiment, the validity the rate equation for densification in hot pressing, originally proposed by Murray, Livey, and Williams.2 i.e., where D = fraction of theoretical density, t = time, P = pressure and 77 is the viscosity, all in appropriate units. This equation was derived from earlier work of Shuttleworth and Mackenzie3 which is based on the closing of spherical pores under the action of surface tension. The integrated form of this equation yields a straight-line relation between log (1 - D) and t. Such conditions were found by Felten4 to be true only after extended periods of pressing. In an endeavor to quantitatively evaluate the exactitude of this equation in the initial sintering stage, i.e., prior to sealing of the pores, spherical anti-

Jan 1, 1962

By W. F. Rochow, W. C. Burke

Numerous designs of linings and accessories, including dams, lifters, and heat exchangers, contribute greatly to kiln efficiencies. Greater conductivity is achieved with basic brick than with fireclay and high-alumina refractories, depending largely upon the use of steel plates in radial joints between adjacent brick to increase heat transfer through the lining. Refractory lifters expose all portions of the load to radiant or convective heat and raise some portions to higher temperatures by cascading the load down through the path of the hot gases.

Jan 3, 1955

By NA NA

Jan 1, 1949

By Albert J. Phillips

FOR the most part, recent changes in nonferrous physical metallurgy have been gradual and of a transition nature rather than abrupt modifications of existing methods. Development of new alloys containing vital constituents in what formerly would have been considered minute amounts has necessitated more precise control of metallurgical procedure than ever before. Realization of the remarkable effects of minute amounts of specific foreign elements in many alloys has brought about a revolutionary control in the selection of even the most commonplace raw materials. In addition, recognition of the widespread occurrence of precipitation hardness in metal systems, and the utilization of many of these, has emphasized not only the need for precise temperature control but also the necessity for considering the time factor in its effect upon properties in the treatment of most metals. These needs have caused the development and widespread installation of equipment that permits precision of control undreamed of a generation ago.

Jan 1, 1935

By Sidney Snook

FLUORSPAR production is the most important industry in a compact area in southern Illinois and western Kentucky bordering the Ohio River. Producers' activities do not usually figure much in the mining news of the country, so that few know that the last year or so has been an unusually active one. Mine shipments more than doubled in 1939 compared with the poor year 1938. The average price changed but little, though it is now about one-sixth higher than at the beginning of last year. The outbreak of war in Europe a year ago lent an immediate stimulus to the industry, though only about 15 per cent of the domestic consumption is normally imported, thanks to a tariff of $8.40 per ton, equivalent to about 30 per cent ad valorem. Be- cause of the increased production and many expansions and improvements in the mines and plants, the period since the beginning of 1939 has been the most important one for the industry in the last 15 years.

Jan 1, 1940

By K. A. Grange, W. S. Holt, E. T. Tkac

Quantitative knowledge of the time clement involved in austenite transformation in a particular steel provides a sound basis for understanding and planning heat-treatment. Such knowledge is conveniently obtained by measurement of austenite transformation as it occurs at each of a series of temperature levels. The results of these measurements usually are summarized in the form of the now familiar isothermal transformation diagram (I-T diagram, TTT diagram, or S-curve). Although a considerable number of such diagrams already have appeared in the literature, there remain many compositions of commercial importance for which no I-T diagram is available. The diagram for many such steels may be predicted from published data with sufficient accuracy for most practical purposes, but for others no satisfactory prediction can be made because the effect on austenite transformation of one or more of the important alloying elements present is not well enough known. Such a steel is Nitralloy, Type 13s-Modified, which, containing about 1.25 per cent aluminum, differs from any whose I-T diagram has been published. This paper presents results of a study of the isothermal transformation behavior of a sample from a commercial heat of this aluminum-chromium-molybdenum steel, together with pertinent supplementary data including the equilibrium transformation temperatures (Aeaand Ae,), the temperature range of martensite formation, and the end-quench harden-ability. These data are directly applicable to the hcat-treatment of this type of steel and are of interest in revealing some of the fundamental effects of aluminum as an alloying element in steel. Material All specimens were prepared from a 1 1/4 i-in. diam bar forged from a 5 by 5-in. billet from a commercial heat made in an electric arc furnace. The composition of the bar was; C, 0.41 per cent: AIn, 0.57: P, 0.016: S, 0.005: Si, 0.24: Ni, 0.17: Cr, I.j7: Mo, 0.36: All 1.26. The forged bar was normalized from r750°F (95s°C) and then tempered for one hour at rzoo°F (650°C), this tempering treatment having been given to facilitate the machining of specimens. Equilibrium Transformation Temperatures In hypoeutectoid steel the minimum temperature at which austenite is completely stable, Aep, and the maximum temperature at which austenite is completely unstable, Ael, are of great significance in heat-treatment. Since these temperatures are dependent upon com-

Jan 1, 1948

By W. S. Holt, K. A. Grange, E. T. Tkac

Quantitative knowledge of the time clement involved in austenite transformation in a particular steel provides a sound basis for understanding and planning heat-treatment. Such knowledge is conveniently obtained by measurement of austenite transformation as it occurs at each of a series of temperature levels. The results of these measurements usually are summarized in the form of the now familiar isothermal transformation diagram (I-T diagram, TTT diagram, or S-curve). Although a considerable number of such diagrams already have appeared in the literature, there remain many compositions of commercial importance for which no I-T diagram is available. The diagram for many such steels may be predicted from published data with sufficient accuracy for most practical purposes, but for others no satisfactory prediction can be made because the effect on austenite transformation of one or more of the important alloying elements present is not well enough known. Such a steel is Nitralloy, Type 13s-Modified, which, containing about 1.25 per cent aluminum, differs from any whose I-T diagram has been published. This paper presents results of a study of the isothermal transformation behavior of a sample from a commercial heat of this aluminum-chromium-molybdenum steel, together with pertinent supplementary data including the equilibrium transformation temperatures (Aeaand Ae,), the temperature range of martensite formation, and the end-quench harden-ability. These data are directly applicable to the hcat-treatment of this type of steel and are of interest in revealing some of the fundamental effects of aluminum as an alloying element in steel. Material All specimens were prepared from a 1 1/4 i-in. diam bar forged from a 5 by 5-in. billet from a commercial heat made in an electric arc furnace. The composition of the bar was; C, 0.41 per cent: AIn, 0.57: P, 0.016: S, 0.005: Si, 0.24: Ni, 0.17: Cr, I.j7: Mo, 0.36: All 1.26. The forged bar was normalized from r750°F (95s°C) and then tempered for one hour at rzoo°F (650°C), this tempering treatment having been given to facilitate the machining of specimens. Equilibrium Transformation Temperatures In hypoeutectoid steel the minimum temperature at which austenite is completely stable, Aep, and the maximum temperature at which austenite is completely unstable, Ael, are of great significance in heat-treatment. Since these temperatures are dependent upon com-

Jan 1, 1948

By W. S. Holt, E. T. Tkac, R. A. Grange

QUANTITATIVE knowledge of the time element involved in austenite transformation in a particular steel provides a sound basis for understanding and planning heat-treatment. Such knowledge is conveniently obtained by measurement of austenite transformation as it occurs at each of a series of temperature levels. The results of these measurements usually are summarized in the form of the now familiar isothermal transformation diagram (I-T diagram, TTT diagram, or S-curve). Although a considerable number of such diagrams already have appeared in the literature, there remain many compositions of commercial importance for which no I-T diagram is available. The diagram for many such steels may be predicted from published data with sufficient accuracy for most practical purposes, but for others no satisfactory prediction can be made because the effect on austenite transformation of one or more of the important alloying elements present is not well enough known. Such a steel is Nitralloy, Type 135-Modified, which, containing about 1.25 per cent aluminum, differs from any whose I-T diagram has been published. This paper presents results of a study of the isothermal transformation behavior of a sample from a commercial heat of this aluminum-chromium-molybdenum steel, together with pertinent supplementary data including the equilibrium transformation temperatures (Ae3 and Ae1), the temperature range of martensite formation, and the end-quench hardenability. These data are directly applicable to the heat-treatment of this type of steel and are of interest in revealing some of the fundamental effects of aluminum as an alloying element in steel. MATERIAL All specimens were prepared from a 13-in. diam bar forged from a 5 by 5-in. billet from a commercial heat made in an electric arc furnace. The composition of the bar was; C, 0.41 per cent: Mn, 0.57: P, 0.016: S, 0.005: Si, 0.24: Ni, 0.17: Cr, i.57: MO, 0.36: Al, 1.26. The forged bar was normalized from 1750°F (955°C) and then tempered for one hour at 1200°F (650°C), this tempering treatment having been given to facilitate the machining of specimens. EQUILIBRIUM TRANSFORMATION TEMPERATURES In hypoeutectoid steel the minimum temperature at which austenite is completely stable, Ae3, and the maximum temperature at which austenite is completely unstable, Ae1, are of great significance in heat-treatment. Since these temperatures are dependent upon com-

Jan 1, 1946

By Walter J. Mead

By American tradition, if not by rational decision, publicly owned natural resources have been transferred to private industry for processing. The process of transfer requires specific determination of the price which the patentee, buyer, or lessee must pay to the government in exchange for the right to develop a resource, and selection of the patentee, buyer, or lessee from among several possible contestants. Pricing of natural resources owned by the government presents a set of problems quite different from ordinary commodity pricing. Natural resources in situ are not homogeneous commodities. Within any class of natural resources, specific leasable parcels will differ in value by reason of location and accessibility, as well as quality and quantity. Thus, there is no "going price;" every lease within a specific resource class will have a different value. To complicate further the pricing and buyer selection problems, competition may not be reliable. Natural-resource markets are characterized by oligopsony conditions. In a significant number of cases, as will be shown later, there has been only one bidder for a given lease, and in most lease sales the number of bidders is equal to or less than three. As a further complication, there is great uncertainty regarding the value of specific resources, even among the best-informed buyers, as well as within the leasing agency. In some instances, particularly with regard to oil and gas resources, there may be uncertainty about the presence of resources, as well as the quantity and quality of any resources contained in the tract offered for lease. In other cases, such as oil shale and some deep ocean minerals where new technologies are involved, the presence of the resource is clearly established. There may be a relatively high degree of knowledge about the quantity and quality of the resource, but there is great uncertainty concerning the cost of production. These problems in total make it difficult for the leasing agency to appraise accurately the resource to be leased, as well as for the potential bidder to calculate a bid price that will yield him a normal profit. The pricing goal of the federal government as the seller or lessee may be to capture the economic rent; that is, the price of a resource might equal its discounted present value. A required price substantially above this amount would either generate no bids, or, in the long run, would bankrupt the buyer. A price below this amount is a disguised subsidy to the lessee. A subsidy to mineral lessees, as to any other economic interest group, as a minimum should be justified by a clear showing of net external benefits from the economic activity. In the case of timber sales by the U.S. Forest Service, the Forest Service Handbook asserts that "the aim in national forest stumpage appraisal is to determine market value,"8 and "market value" is equated to "fair market value." Regarding minerals, there is no reference in legislation or regula-

Jan 1, 1976

By M. M. Singh, J. W. Brown

Three rocks of highly varied physical properties are selected for the first reported experimental study concerning microseismic activity of rock under tension to determine the effects of static fatigue, loading rate, repeated loading and rock anistropy compared to compression and bending loads. The microseismic method of detecting rock under deformation may be a great potential tool in surveillance and location in situ of dangerously stressed strata, as well as predicting rock failures. Noises emitted under load or the rate of energy (energy of noise pulses generated per unit time) are computed for varying conditions. The tests are conducted at constant load on a dead weight loading machine to eliminate all possible extraneous noises — an indispensable precaution — at various load levels. Experimental results are reported including the relation of total energy emitted to tensile strength of rock and the possibility of simulating a phenomenological model for microseismic activity. Plots of some of the experiments are included. INTRODUCTION Rock failure, whether on a large scale faulting in the earth's crust and rock bursts in mines, or on small scale ruptures of laboratory test specimens, generates transient vibrations in the rock mass. Mechanisms of intermittent deformation, such as twinning and cracking through and between mineral grains, also produce similar vibrations, but of very small amplitude. Such vibrations from both deformation and failure are referred to as microseismic activity, rock noise, or occasionally seismo-acoustical activity. An individual rock noise is sometimes

Jan 1, 1967

Jan 1, 1969

Jan 1, 1969

By AIME AIME

The following report is published for the information of the members Meetings. Two meetings for the reading and discussion of papers, etc., have been held during the year 1906-namely, the Ninetieth meeting, held February 21st to 24th at Bethlehem, Pa., and the Ninety-first meeting, held July 24th to 27th in London, England, in connection with the meeting of the Iron and Steel Institute. The proceedings of these meetings, including descriptions of the entertainments and excursions connected therewith, have already been published and distributed to the members of the Institute; the Bethlehem meeting in Bi-Monthly Bulletin, No. 9, May, 1906, pp. 497 to 508, and the London meeting in Bi-Monthly Bulletin, No. 12, November, 1906, pp. 809 to 908. The proceedings of the London meeting were published separately and distributed among the many individuals and concerns whose cordial friendship and delightful hospitality contributed so largely to the success of the visits in London and environs and the excursions in England, Scotland and Germany. At the Bethlehem meeting, 37 papers and discussions were presented and the names of 198 members and guests were regis¬tered at the Institute headquarters ; this number, however, does not represent all who were present at the sessions and excur¬sions. At the London meeting, 26 papers and discussions were presented, not including 5 of the papers and discussions read before the Iron and Steel Institute at the joint session with the American Institute of Mining Engineers, which, by a mutual agreement between the Councils of the two Institutes, have been selected to be republished in the Bi-Monthly Bulletin and Transactions of the Institute. The number of members and guests of the two Institutes registered at the London headquarters was 908, and of this number 131 were from America. This list does not include the names of all who

Mar 1, 1907

By David Cole

THE appearance of the Wilfley table in 1897 marked an epoch in the art of concentration of ores. The table has merited and received an almost unprecedented measure of public approval, lasting through its whole patent life. It has been very little improved in itself, or improved upon by competitors. The new machines bidding for popular favor have been of the Wilfley family, but without ability to do markedly better work than the parent m:-chine, or to (to more work except by the use of superimposed decks, the latter having obvious disadvantages. FIG. 1.-The- Butchart RIFFLE System. During the past three years there has been developed at Morenci a new type or arrangement of riffles applicable to the Wilfley type of concentrating table which corrects many of the objectionable features or limitations of the older system and obviates most of the difficulties encountered with it, particularly when handling ores having a low ratio of concentration. The new type is known as the Butchart1 riffle system, and its general arrangement is shown in Figs. 1 and 2.

Jan 2, 1915

By Arthur Notman

TO present some idea of the magnitude of the gold-mining industry of Canada and the world, the records of 106 gold-mining companies currently paying dividends have been studied. Forty of these are in Canada, and 37 on the Rand in South Africa, these being all the straight gold-mining companies that paid dividends in the two areas in 1938. None of the base-metal companies that produce gold as a by- product, or even as a major fraction of the value of their total product, have beezl included. In addition, a group of 29 similar companies from Southern Rhodesia and the Gold Coast in Africa, India, Australia, Manchuria, Philippine Islands, the

Jan 1, 1939

Organization Place Date 1918 American Society of Mechanical Engineers...:.. Worcester, Mass. June 4-7 American Institute of Chemical Engineers Berlin, N. H. June 19-22 American Concrete Institute Atlantic City, N. J. June 24-26 American Society for Testing Materials Atlantic City, N. J. June 25 28 American Institute of Electrical Engineers Atlantic City, N. J. June 26-28 New York Electrical Society, Annual Meeting... New York, N. Y. June American Institute of Mining Engineers Colorado Sept. 2-7 National Association of Stationary Engineers.... Cincinnati, 0. Sept. 9-13 British Iron and Steel Institute, Autumn Meeting London, Eng. Sept. 12-13 National Exposition of Chemical Industries New York, N. Y. Sept. 23-28 American Chemical Society Cleveland, 0. Sept. National Petroleum Association.: Atlantic City, N. J. Sept.

Jan 6, 1918

Four years of intensive exploration effort by Newmont Mining Corp. came to a climax May 27 in Carlin, Nevada, when local, state and federal officials joined with company officers at a dedication ceremony saluting the start-up of the firm's wholly- owned subsidiary, Carlin Gold Mining Co. Before an invited audience at the plant site, Newmont's President Plato Malozemoff and Nevada's Senator Howard D. Cannon pushed a lever and watched the new melting furnace rotate until a brilliant orange-red stream of molten gold poured forth from its mouth. Two 1200-oz bricks of bullion were poured that day, and they are the first of many that will lift this mine into the number two slot among U.S. gold producers and fourth among all gold mines on the North American continent. Although Newmont Mining first entered the gold mining business in 1929 in Grass Valley, California, the Company had operated no gold producers since the well-known Government directive L208, issued in 1942, closed down U.S. gold mines for the duration of World War 11. Now it is back in the business in a big way-a $10 million mine and plant capable of producing 200,000 oz. per year. All the gold from the Carlin operations is earmarked for the U.S. Mint in San Francisco.

Jan 7, 1965

By R. W. Kewish

The preparation of massive uranium metal containing very low concentrations of a number of light elements by bomb reduction of UF4, with calcium is described. Details of procedures are given for preparing high-purity ingredients for the bomb reduction. The as-reduced uranium metal contained, on the average, less than the following amounts of light element impurities, in ppm: Li, 0.1; Be, 0.1; B, 0.1; C, 25; 0, 70; Na, 1; Mg, 3; Al, 2; and Si, 7. Other impurities for which the metal was examined averaged, in ppm: Ca, < 10; V, < 10; Cr, 2; Mn, 6; Fe, 50; Co, < 5; Ni, 8; and Cu, 1. THE preparation of very high-purity uranium metal in massive form for research purposes is of great importance. Recently the kilogram-scale preparation of uranium metal containing less than 70 ppm of detected impurities was accomplished by Blumen-thal and coworkers by vacuum remelting of high-purity crystals of uranium obtained by fused salt electrolysis.1"3 Albert and coworkers4 have reported successful experiments in lowering the concentrations of certain impurity elements in uranium, notably iron, to a few ppm by the zone-melting method. The present paper describes the preparation of high-purity massive uranium metal by the bomb reduction of UF4, with calcium. Early in 1951 a program was undertaken at the Los Alamos Scientific Laboratory to prepare uranium metal of very high purity with respect to a number of the light elements. The methods considered for this purpose were 1) bomb reduction of a uranium halide with calcium, 2) electrolysis of fused salts, and 3) hot wire decomposition of UI4, The first of these processes had been used extensively at Los Alamos since 1943 (and still is used) for the production of uranium metal.5 In considering the three processes it was evident that either of the last two would require an extensive development program with no certainty of success. On the other hand, a study of available data showed that uranium metal of very high purity with respect to some light elements had occasionally been made in routine processing by the first method. It was therefore decided that an intensive study of the bomb-reduction process would be made to see if it could be improved to yield uranium metal with very low concentrations of light elements. DEVELOPMENT OF PROCEDURES The bomb-reduction process used at Los Alamos consists of reducing UF4 with calcium, using iodine as a booster. The reaction is carried out in a magnesium-oxide crucible enclosed in a steel bomb. Argon is used in the bomb to avoid objectionable side reactions which would occur in the presence of air. All ingredients for this bomb-reduction process were examined as possible sources of light elements. It was known that high-purity UF4 was required. The calcium used in the reductions was a source of carbon and magnesium. The magnesium-oxide crucibles were sources of boron, silicon, and magnesium. The iodine did not appear to be a source of any impurities. Pure UF4- The UF4 for bomb reduction is prepared from U3O3 , by successive reduction to UO2, with hydrogen and hydrofluorination of the UO2, with anhydrous HF. Since it was known that no impurities were normally introduced during the gas-solid reactions, effort was directed toward the preparation of high-purity U3O3. Of the many possible procedures for the purification of uranium solutions the following were investigated: 1) Precipitation of uranium peroxide. (Two procedures were tried. The first consisted of simultaneously adding hydrogen-peroxide and ammonium-hydroxide solutions to a uranyl-nitrate solution, containing citric and malonic acids, at such relative rates that precipitation was carried out at a constant pH of 1.5 The second consisted of simultaneously adding uranyl-nitrate, ammonium-hydroxide, and hydrogen-peroxide solutions to an aqueous solution

Jan 1, 1960

CONTENTS RUSSIA-R. C.-BECKSTROM 3 VENEZUELA-F. H. KAY 9 TRINIDAD-W. J. MlLLARD 20 RUMANIA-1. I. GARDESCU 26

Jan 1, 1932

By D. A. Elgillani, M. C. Fuerstenau, J. D. Miller

Adsorption of lead and ferric iron on quartz and alumina is presented as a function of pH. Only the hydrolyzed species of these metal ions, FeOH++ and PbOH+, adsorb significantly on each of these minerals. Zeta potentials of quartz were measured as a function of pH in the presence of various additions of aluminum, lead, and magnesium salts. Sign reversal occurs at the pH values where significant concentrations of hydroxy complexes are formed. Models of adsorption are presented in the absence and presence of collector. The mechanism of adsorption of metal and collector species in the activation of nonmetallic minerals is still the center of considerable discussion in spite of the extensive study given this system. Until recently, the view was widely held that hydrated metal ions were responsible for this phenomenon. This fact is surprising, since it had been shown that the pH range in which flotation is effected corresponds to that in which metal ion hydrolysis occurs.&apos; Additional support of this concept was pro vided by the work of Wolstenholme and Schulman in another system.&apos; Later work has shown that hydroxy complexes of metal ions are the active species. These studies have also indicated that basic aqueous complexes of metal-collector may be necessary for flotation.3-7 Depending on the molecular weight of the collector, formation of these complexes may occur before or after precipitation of the metal-collector salt has occurred. Ion pair formation can occur when low molecular weight collectors are involved because relatively high concentrations of metal hydroxy complex and collector can be present in solution before precipitation occurs. This is not the case when high molecular weight collectors are used. A model of aqueous complex adsorption has been presented6,7 in which it has been assumed that adsorption occurs by the formation of water from adsorbed hydroxyl and hydrogen of the hydroxyl contained in the complex. Other authors8 have suggested that hy-droxy complexes are involved in these systems but that collector adsorption occurs by replacement of the hydroxyl of the adsorbed metal hydroxy complex with a fatty acid anion. All of these investigations have involved mineral surfaces that were negatively charged so that it is not possible to state with certainty whether hydrated metal ions or hydroxy complexes are the active species in this system. Use of a positively charged mineral should be helpful, however, since the hydrated metal ion will be repelled from this surface. On the other hand, if the hydroxy complex adsorbs by splitting out water, surface charge should have no effect because of the free energy decrease that the system will experience when water is formed. In this regard, sapphire is well-suited for study, since its surface is positively charged until approximately pH 9. Electrokinetic studies of quartz in the presence of various metal ions should also be useful in establishing the mechanisms of adsorption in these systems. That is, if the hydroxy complexes adsorb by water formation, drastic changes in the zeta potential should occur in the pH range in which hydrolysis occurs. In this view, adsorption of ions of widely different hydrolysis characteristics on both sapphire and quartz was measured. In addition, zeta potentials of quartz were measured as a function of pH in the presence of various metal ions and compared with flotation responses obtained under similar conditions. Experimental Materials and Techniques Reagent-grade aluminum, ferric and magnesium chlorides, and lead nitrate were used in this investigation. Adjustments in pH were made with reagent-grade HCl or KOH. Conductivity water, made by passing distilled water through an ion exchange column, was used in all of the experiments.

Jan 1, 1971