Search Documents

By N. V. Hansell

l. INTRODUCTION. THE last few years have shown an increasing interest in the subject of beneficiating iron-ores -in all iron-producing countries. In the United States, this movement has been slower than in certain parts of Europe, for the obvious reason that the abundance and relative cheapness of the Lake Superior iron ores has hindered the development of enterprises for the preparation of low-grade ores. Gradually, however, conditions have changed. The world's consumption of iron is increasing enormously. Being in 1900 about 40,000,000 tons, in 1910 ii was already 60,000000; and there is no reason to doubt that for the near future the increase in iron-consumption will continue at the same rapid rate, especially with, the development of China, certain parts of Africa, and other regions which have hardly been touched as yet by modern industrialism. It is. therefore, not surprising that apprehension is felt that the known available iron-ore resources of the world are gradually being depleted. Signs of this feeling are the recent investigation, under the direction of the U. S. Geological Survey, of the iron-ore resources of the United States, and the estimate presented to the last International Geological Congress, at Stockholm, Sweden, of the iron-ore resources of the world. These investigations have emphasized the fact that the known high-grade ore-deposits are limited in extent, and will, at a not distant future, be exhausted, compelling the iron industry to depend for raw material on the enormous deposits of low-grade ores which are distributed over almost all the world. The discovery of new deposits of high-grade ore, in countries not yet thoroughly explored, will not materially change this prospect. Of course, the part which such new deposits will play in the future cannot be forecast. The difficulty and cost of transportation will probably exclude many of them from use at the present centers of the iron industry.

May 1, 1912

By E. N. Harshman

The Wind River Formation of Eocene age is the host rock for large high-grade uranium deposits in the Shirley Basin. The major deposits are in a northwest-trending belt of sandstones that were deposited in stream channels and that were lithologically favorable for uranium accumulation. Paleotopography influenced the character and position of the belt. The major deposits within the belt are at, or near, the margins of large tongues of altered sandstone formed in the most transmissive parts of thick sandstone beds. At least two tongues of altered sandstone are present in the belt, one of which is 5 miles long, 3 miles wide, and 70 feet thick; the other tongue is somewhat smaller. Ore bodies consist of a few hundred tons to several hundred thousand tons of material containing from 0.10 to about 2.00 per cent U3O8. The ore mineral is uraninite associated with pyrite, marcasite, hematite, and calcite. Deposition is believed to have taken place when neutral to slightly alkaline, oxidizing, uranium-bearing ground water, on entering the basin, encountered a reducing environment. The reductant may have been H2S of biogenic origin. Geology played an important role in discovery, exploration, and development of ore in the Shirley Basin.

Jan 1, 1968

By Howard N. Eavenson

TWO months ago, just after the coal code hearing in Washington, one of our leading liberal weeklies printed a study of the coal industry made by an economist in the Administration, and on the outside cover bad it featured as "Coal-A Dying Industry." There are, of course, different opinions as to the accuracy of this characterization and I want to present some of the facts about the outlook for the bituminous industry for a short time ahead. In view of what has happened in the industry within the recent past it would be futile to attempt to make any prophecy about what is likely to occur in the future. We all know that a prophet is not without honor save in his own country, but it is likely that anyone undertaking this role about this industry would soon find himself in no man's land. One can, with some slight degree of safety perhaps, outline present conditions and tendencies and draw some inferences as to what the future may hold.

Jan 1, 1933

By R. T. DeHoff

A theoretical development is presented which reformulates Fick's first law for diffusion in the solid state. The diffusion flux of component i in a multi-component system, Ji, is related to its local concentration, ci, and local jump frequency, ri : where a is a geometric factor and d is the jump distance. The product, ciri , is defined as the local concentration of atomic jumps for component i. The analog to Fick's second law is also derived. A solution to this equation is presented, which permits the experimental determination of the variation of atom jump frequency with composition in multicomponent systems. HISTORICALLY, the description of diffusion in the solid state has been presumed to be best approached as an application of more general diffusion laws, known as the phenomenological equations. These equations relate the flux, Ji, of the various components, expressed in atoms, grams, or volume, to the driving force involved, expressed as either a compositional or chemical potential gradient, sumption that the flux is simply proportional to the driving force is the foundation of this approach. The phenomenological equations take the form: where the concentration gradients are assumed to be the driving force, and: if the chemical potential gradient is taken as the driving force. The coefficients Dij in Eq. [1.] are the "diffusion coefficients"; the elements of the corresponding matrix in Eq. [2], the Mij, are called the "mobilities". Eqs. [I] and [2] may be considered to be definitions of these phenomenological coefficients. A formidable body of literature has been generated about these equations; this literature dates back to their original formulation for the simplest case of binary diffusion in a fluid, by Adolf Fick, in 1855.' This description has been shown to be self-consistent. However, the "constants of proportionality", the Dij or ,Mij, are not constant: they vary with composition in all but the simplest systems. Even in the case of tracer diffusion, wherein it can be shown that the diffusion coefficient is constant, the mobility, which is considered in irreversible thermodynamics to be the more physically meaningful quantity, varies with the concentration of the tracer involved.' In more complex systems, it is necessary to evaluate the entire matrix of phenomenological coefficients, as a function of composition, in order to describe diffusion locally. Further, in order to determine this matrix experimentally, it is necessary to produce diffusion couples that have different sequences of compositions; the matrix may be evaluated only at points where these "composition paths" cross.* Finally, and perhaps most

Jan 1, 1969

By Lawrence K. Nordell

This paper reviews practices used In the selection and sizing of belt conveyors and stacker systems commonly used in crushing and grinding plant facilities. Historical and modern methods of sizing this equipment are presented. The new methods Include: 1) probability theory applications for establishing component reliability, 2) "Monte Carlo" simulation techniques used in evaluating alternative system designs and in establishing service factors and corresponding availability Indices of each system, 3) quantifying the system and component operating characteristics using computer assisted modeling tools simulating rigid body and elasto-mechanic behavior for starting and stopping large and/or complex belt conveyors.

Jan 1, 1982

By H. Hubert

THE first attempts at direct utilization of blast-furnace gas in engines were made in 1895. For a considerable time the gas had been burnt in Cowper stoves for heating the blast for the furnace, and under the boilers which supplied steam to the blowing-engines, and others serving the furnaces. It was natural, therefore, that the idea of directly employing it in gas-engines should have occurred simultaneously to several engineers, notably to Lürmann and to Lencauchez, who had pointed out the blast-furnace as a powerful -gas-producer. Nevertheless, nowhere had any attempt been made to apply it to this purpose up to the end of 1894, when Thwaite proposed it to Mr. James Riley, of the Glasgow Iron & Steel Company. About the same time investigations were being made in Belgium and in Germany, independently of Thwaite's experiments, which were not generally known on the Continent. The industrial world, which up to that time had hardly favored the idea, had thus been gradually prepared to receive it. The gas-engine, long restricted to small sizes and dependent upon the use of an expensive fuel obtainable only in large centers, now began to make headway. At the Paris Exhibition of 1889 two engines of 100 h.p. were shown and excited much interest among engineers. One had four cylinders, and was made at the celebrated works of the Deutz Company, and the other was a single-cylinder engine, exhibited by two French designers, Messrs. Delamare-Deboutteville and Malandin. In the meanwhile the design of gas-producers had made important progress, completely freeing the new engine from its

Nov 1, 1906

By Henry D. Hibbard

I. INTRODUCTION. THESE impurities are perhaps the most important things in steel-especially steel made by the oxidation processes-the effect of which has not been at least approximately determined. By oxidation processes I mean the Bessemer and Siemens-Martin, during which the metalloids in the charge are removed by oxidation. It has been truly said that it is a clear advantage to have a new name for a new thing. To secure this and to economize space, let us adopt the name sonim (plural sonims) to designate the solid non-metallic impurities existing in steel or other metal. I would define a sonim as a solid non-metallic portion of matter existing as an impurity in metal. A piece of sand, brick, clay, or such material, imbedded in metal, would be considered as a foreign body, not as an impurity, and therefore not a sonim. The studies of sonims of which the results have been published hitherto, have been made chiefly or wholly on finished or at least on cold steel, without much, if any, regard to the specific methods by which the steel was made. While many of the results so obtained are valuable, they give little help in determining the cause, effect, or cure of the disease. It is not enough, in such a study, to know merely the commercial name of the process; for within the field of each process lies a great number of possible variations, each of which will yield a result differing in some respect from all others; and the control of sonims is particularly dependent. on the metallurgical treatment of the metal, because of the inability of analytical chemistry to throw much light on their presence, condition, and effect, as they usually occur in commercial steels. The microscope aids more, perhaps, than chemistry in their study.

Apr 1, 1911

By Frank A. Howard

WHAT are the reasons for the present public interest in the synthetic fuel industry, an interest which has culminated in the recommendation of the Secretary of the Interior that we start at once on a nine billion dollar program of construction? Three separate factors seem to have combined to create this pressure. First are recurrent seasonal and spot shortages of gasoline, fuel oil, and natural gas. Second is the international outlook, which forces us to face the possibility of war, with all that means in the way of increased call on our domestic resources and interference with our foreign commerce. The shortages we have experienced are superficially the result of lack of transportation, but basically they reflect a rapidly rising demand which has outstripped the expansion of productive facilities of all kinds. Not only oil and gas, but steel, coal, automobiles, and meat are temporarily in short supply for much the same reasons. The military problem has both long-range and short-range aspects, but the immediate necessity is to create reserve capacity in the United States to supply perhaps 2,000,000 barrels daily additional liquid fuel in time of war.

Jan 1, 1948

By N. G. W., Cook

When an excavation is made underground the original rock stresses are removed from the surfaces of the excavation. These surfaces converge to partially close the excavation and the superincumbent rock mass moves down towards the excavation. If the convergence of the surfaces of the excavation were controlled, energy generated by their motion against the controlling forces could be extracted. Since the total forces in the rock mass are not significantly affected by the excavation, stress concentrations arise around the excavation, which compensate exactly for those stresses no longer transmitted through the excavation. These phenomena give rise to two general principles which provide the basis for analyzing the effects of making any underground excavation. The first of these is that the total force resulting from the stresses across any plane in the rock, including any plane through the excavation, must be the same before and after the excavation is made. The second of these is that energy must necessarily be released as a result of making an underground excavation.

Jan 1, 1969

By Thomas Brownfield

Development and production activity in Oklahoma during the year 1940 was of routine nature. Production, according to the Corporation Commission's figures, averaged 409,100 bbl. daily as compared with 421,000 bbl. for the year 1939. Discoveries were of minor importance except for the Cumberland pool in Marshall and Bryan Counties, in the southern part of the state. Maintenance of a relatively stable producing rate is attributable to the drilling of new wells and the recompletion of many old wells in the previously established producing areas. During the year 1785 new wells were drilled, a decline of approximately 10 per cent as compared with the previous year. Of the wells drilled, 962 were oil wells with a combined initial production of 241,000 bbl. daily, 172 were gas wells having aggregate capacities of 1205 million cu. ft., and 651 were dry holes. Wildcat activity increased 20 per cent over 1939 and 227 such wells were completed during the year; that isl 43 oil wells, 16 gas wells, and 168 dry holes. In addition to the new work completed, 603 wells were recorded as having been drilled deeper or plugged back to test new horizons; included were 334 producing wells with total initial production of 65,000 bbl. daily, 37 gas wells with initial aggregating 305 million cu. ft., and 232 abandonments. Footage drilled amounted to 4,730,000 ft., an average of 2650 ft. per well as com-pared with an average depth of 2600 ft. recorded the previous year. The principal new pools discovered as a result of the exploratory drilling were Cumberland; East Cromwell, in Okfuskee County, and Prague, in Lincoln County. At the end of the year Cumberland had 13 completed wells, which averaged 700 bbl. initial through tubing from the Simpson Bromide formation (Ordovician) at 4750 ft. East Cromwell had 10 wells with average initial of 435 bbl. in the Cromwell sand (Pennsylvanian) at 3460 ft. Prague had II wells with an initial average of 220 bbl. from the Senora sand (Pennsylvanian) at 3260 ft. There were notable extensions to the Dill pool, Okfuskee County, and to the Hewitt pool, Carter County. At the end of the year, 19 producing wells had been drilled in the former, with initials averaging 1000 bbl., and 63 wells averaging 150 bbl. daily in the latter. There were no notable changes in the policy of State conservation authorities with respect to proration. The Bureau of Mines recommendations for the year averaged 413,000 bbl. daily; the State author-ities fixed allowables at an average of 406,000 bbl. daily, while, as noted above, production averaged 409,100 barrels. The most important development in the older areas occurred in the following pools: Billings.—Seven oil wells with an average initial production of 2500 bbl. and two dry holes were completed during the year. Production from the Simpson horizon averaged 6025 bbl. daily as compared with 5950 the previous year. Production from this field has been almost steady since reaching its peak early in 1937. The major portion of the pool is efficiently operated as

Jan 1, 1941

By Thomas Brownfield

Development and production activity in Oklahoma during the year 1940 was of routine nature. Production, according to the Corporation Commission's figures, averaged 409,100 bbl. daily as compared with 421,000 bbl. for the year 1939. Discoveries were of minor importance except for the Cumberland pool in Marshall and Bryan Counties, in the southern part of the state. Maintenance of a relatively stable producing rate is attributable to the drilling of new wells and the recompletion of many old wells in the previously established producing areas. During the year 1785 new wells were drilled, a decline of approximately 10 per cent as compared with the previous year. Of the wells drilled, 962 were oil wells with a combined initial production of 241,000 bbl. daily, 172 were gas wells having aggregate capacities of 1205 million cu. ft., and 651 were dry holes. Wildcat activity increased 20 per cent over 1939 and 227 such wells were completed during the year; that isl 43 oil wells, 16 gas wells, and 168 dry holes. In addition to the new work completed, 603 wells were recorded as having been drilled deeper or plugged back to test new horizons; included were 334 producing wells with total initial production of 65,000 bbl. daily, 37 gas wells with initial aggregating 305 million cu. ft., and 232 abandonments. Footage drilled amounted to 4,730,000 ft., an average of 2650 ft. per well as com-pared with an average depth of 2600 ft. recorded the previous year. The principal new pools discovered as a result of the exploratory drilling were Cumberland; East Cromwell, in Okfuskee County, and Prague, in Lincoln County. At the end of the year Cumberland had 13 completed wells, which averaged 700 bbl. initial through tubing from the Simpson Bromide formation (Ordovician) at 4750 ft. East Cromwell had 10 wells with average initial of 435 bbl. in the Cromwell sand (Pennsylvanian) at 3460 ft. Prague had II wells with an initial average of 220 bbl. from the Senora sand (Pennsylvanian) at 3260 ft. There were notable extensions to the Dill pool, Okfuskee County, and to the Hewitt pool, Carter County. At the end of the year, 19 producing wells had been drilled in the former, with initials averaging 1000 bbl., and 63 wells averaging 150 bbl. daily in the latter. There were no notable changes in the policy of State conservation authorities with respect to proration. The Bureau of Mines recommendations for the year averaged 413,000 bbl. daily; the State author-ities fixed allowables at an average of 406,000 bbl. daily, while, as noted above, production averaged 409,100 barrels. The most important development in the older areas occurred in the following pools: Billings.—Seven oil wells with an average initial production of 2500 bbl. and two dry holes were completed during the year. Production from the Simpson horizon averaged 6025 bbl. daily as compared with 5950 the previous year. Production from this field has been almost steady since reaching its peak early in 1937. The major portion of the pool is efficiently operated as

Jan 1, 1941

By J. W. Byrkit

Design features and operating methods at the new Ajo smelter are described in detail. Successful operation of a novel method of handling and charging wet concentrates to a deep bath type reverberatory furnace contribute to the daily production of 200 tons of anodes with good results from the standpoint of both metallurgy and economy. THE New Cornelia Branch of the Phelps Dodge Corp. is located at Ajo, Ariz. Large scale mining operations were started at Ajo in 1917, when a 5000 ton leaching plant was put in service to treat the copper carbonate ore that overlaid the sulphide ore-body. In 1924 a 5000 ton flotation plant was built to treat the sulphide ore and the leaching operation was abandoned a few years later. Changes in practice and additions to plant facilities have resulted in a gradual increase in the milling rate which now approaches 30,000 tons daily. Prior to the erection of the Ajo smelter, flotation concentrate was shipped by rail to Douglas, Ariz, where it was treated in the Phelps Dodge smelter. Construction of a one reverberatory furnace smelter to produce an average of about 200 tons per day of copper anodes at Ajo was started early in 1949. Initial heating of the reverberatory furnace was begun on June 21, 1950. Charging the furnace was started on july 8, and the first anodes were cast on July 14. Neither the anode furnace nor the reverberatory furnace has cooled since the initial firing. Fig. 1 is a photograph of the new smelter. Built primarily to eliminate the '300 mile haul of concentrate to the Douglas plant, the new smelter was designed to treat the Ajo concentrate, with a minimum of capital investment. A novel, and relatively simple, method of concentrate handling and furnace charging made unnecessary the installation and operation of expensive storage facilities and reclaiming equipment, and obviated the necessity of holding in storage large quantities of copper-bearing materials. (Patents are pending in the United States and abroad on the Ajo process.) In the selection and arrangement of equipment, consideration was given to the full utilization of all smelting facilities, reducing the amount of idle equipment to a minimum. The layout of the smelter is shown in Fig. 2. The important problem of internal transportation was minimized by arranging the reverberatory furnace, converters, and anode furnace in a compact group and providing storage bins inside the smelter building, within reach of overhead cranes, for fluxing materials and other supplies needed in the daily operation. This can be seen in the sectional view of the smelter given in Fig. 3. Incorporated in the design were many innovations in smelting equipment intended to facilitate operations and effect economies in maintenance expense and manpower requirements. Table I gives operating data of the entire plant. Metallurgy The metallurgical practice at Ajo is based essentially upon the use of a single, deep bath reverberatory furnace for smelting wet concentrate, without concentrate storage facilities. The large reservoir of slag and matte maintained in the furnace serves to equalize, to some extent, the day to day variations in the nature and grade of concentrate and permits

Jan 1, 1954

By R. S. Dean

REQUIREMENTS for war materials have led to large scale experimentation upon metallurgical innovations. It is of interest to inquire what this may contribute of permanent value to our existing technology, as innovations adopted during war are apt to be discarded promptly at its end. This is because utilization of substandard ores usually requires a new technology for ore treatment, and a new use-pattern for employment of the products. Thus two very different problems are involved: first, devising a process; then, adopting its products by industry, with readjustments of the use-pattern if necessary. A new process may be as good or better than an old one, but the readjustments required for use of its products may prevent its general adoption if this implies scrapping existing plants and investing much additional capital. Metallurgical innovations are of three kinds: I. The use of substandard material in processes already established; 2. The grading-up of substandard material to render it more suitable for established processes; 3. The adjustment of technology and use-pattern to the raw materials that we have.

Jan 1, 1945

By G. C. Trevorrow

STRIP mining during 1943 increased considerably with further extension of mechanical loading in mines already partly mechanized; with the considerable introduction of mechanical loading into hand-loading mines; and with improvements in the use of loading equipment. Extension of the use of machinery both in strip mining and underground is due to reduction in labor supply and increased cost of labor, together with the increased demand for coal during the period of labor shortage.

Jan 1, 1944

By D. W. Smith

The beta solid solution phases of the systems copper-zinc, copper-aluminum, copper-tin and silver-zinc are structurally analogous.' R. F. Mehl and 0. T. Marzke2 have shown that the a phase upon segregating from the 6 phase in the system copper-zinc takes the form of needles lying parallel to a [Ill] direction or some similar direction, such as [556], of the parent solid solution, and that the a phase upon segregating from the ß phase in the system copper-aluminum also takes the form of needles. By analogy they assume that in this case also the segregate needles lie parallel to the [ill] or [556] direction in the ß lattice. The purpose of this investigation is to determine whether the structures resulting from segregation of the a phases from the respective ß phases of the systems copper-tin and silver-zinc are analogous to those obtained by Mehl and Marzke in the systems copper-zinc and copper-aluminum. Segregation of the a Phase from the ß Phase in the Copper-tin System Preparation of the Alloy.—An alloy containing 74.92 per cent (by weight) of copper and the balance tin was chosen for this investigation. This alloy, as can be seen from a portion of the constitutional diagram, Fig. 1, of the system copper-tin by Hamasumi and Nishigori,3 with the proper heat treatment should segregate the « phase out of the a parent, solid solution phase. The alloy was prepared from high purity cathode copper (analyzing 99.98 per cent Cu) and Straits tin (analyzing 99.94

Jan 1, 1933

By Hewitt Wilson

IN 1903, T. M. and E. H. Alvord, of Marblemount, Wash., built a soapstone-grinding mill in the Skagit River Valley and are reported to have produced "ground talc" during 1904 and 1905, shipping to the paper mills in Wisconsin. Between 1916 and 1920, the Western Talc Co. built and operated a talc-grinding mill north of Mondovi, on the banks of the Spokane River, in eastern Washington, and sold powdered talc to the Inland Empire Paper Co. of Spokane. ? The most active develop-ment in recent years has been by two companies in the Skagit Valley-the Skagit Talc Company, Inc., which has been sawing soapstone block for the soda-recovery furnaces of the pulp and paper companies, and the Asbestos-Talc Products of Washington, Inc., at Burlington, which has been mining and dry-grinding a soft serpentine for the structural filler and insulation trade. Many prospects have been opened in the northern part of the state on both sides of the Cascade Mountains, and these activities undoubtedly are the forerunner of an industry that promises to attain considerable magnitude in the North Pacific States. At the present time, talc is imported from California for use as paper filler, and soapstone block from Virginia for use in the soda-recovery furnaces. A small market has been created locally for tailor and foundry:, pencils, stove grills, and block soapstone for art objects. The results of the present study, as yet incomplete, indicate that the use as a refractory and as a ceramic filler and flux can be expanded.

Jan 1, 1936

By J. W. Eckerd, P. S. Lewis, N. H. Coates

USBM designed, constructed, and operated an 18-in.-diam fluidized-bed combustor for highly caking coals to evaluate the method for possible application to power generation. In initial tests, combustion was carried on successfully, with carbon losses as low as 0.8%+ Coal ash was not satisfactory as a bed material, but mullite proved to be acceptable. Overall heat-transfer coeffients from the bed (-20 t 50 mesh mullite) to a water-cooled tube were about 75 Btuper hr-sq ft. Fluidized-bed combustion is being investigated by the U. S. Bureau of Mines (USBM) as a potentially cheaper method of firing power plant boilers. Lower combustion temperatures in fluidized beds—only 1400" to 1800°F-—should reduce fireside deposition and corrosion and nitrogen oxides production. Fluidized-bed combustion also offers possible advantages in the use of additives to control SO, emissions and amenability to processing of high-ash, high-moisture coals without special preparation. This paper describes development of a fluidized-bed combustor and the results of preliminary tests. Equipment and Procedure Fig. 1 shows the 8-ft-high combustor. A cone-shaped plate perforated by I/8-in.-diam holes supports the fuel bed and admits the fluidizing air; water passing through the 3/4-in. pipe extracts heat from the combustion bed. Fig. 2 is a flow diagram of the system. Coal is fed pneumatically to the base of the fuel bed. Combustion products are passed through two centrifugal separators to remove most of the entrained solids, then to a water

Jan 1, 1971

The following is an incomplete list of members and guests who called at Institute headquarters during the period Jan. 10, 1918 to Feb. 10, 1918: K. Baumgarten, San Diego, Cal. J. A. Meyerovitch, Petrograd, Russia. F. J. Brine, Toronto, Ont., Canada. C. Naramore, Washington, D. C. W. A. Castleton, Salt Lake City, Utah. Orrin P. Peterson, Wausau, Wis. J. Ross Corbin, Boyerton, Pa. William H. Rea, Pittsburgh, Pa. W. M. Corse, Buffalo, N. Y. W. Murray Sanders, Tucson, Ariz. W. A. Deane, Summitville, N. Y. Edmund F. Saxton, Philadelphia, Pa. S. E. Doak, Philadelphia, Pa. William C. Schmidt, Humboldt, Ariz. F. G. Downs, Jersey City, N. J. G. J. Sielaff, Oakland, Cal. Albert H. Fay, Washington, D. C. A. D. Sproat, Bound Brook, N. J. F. Julius Fohs, Tulsa, Okla. J. A. Stader, Joplin, Mo. A. L. Gholz, Minneapolis, Minn. A. K. Stewart, Mine La Motte, Mo. Ruger W. Hay, Easton, Pa. Geo. W. Tower, Jr., New Rochelle, N. Y. Stanley C. Herold, Pittsburgh, Pa. Henry Traphagen, Toledo, Ohio. A. A. Holland, Montreal, Canada. H. E. Treichler, Chuquicamata, Chile. T. Z. Humphrey, Anaconda, Mont. Paul M. Tyler, Fairlee, Vt. H. M. LaFollette, LaFollette, Tenn. F. R. Van Campen; Seattle, Wash. J. B. Lain, Goldfield, Nev. Thor Warner, Phoenix, Ariz. J. R. Lashbrooke, Los Angeles, Cal. Clarence Woods, Narrows, Va. W. F. Lewis, Ewen, Mich. E. N. Zern, Pittsburgh, Pa. C. E. McQuigg, New Haven, Conn. Robert J. Anderson has resigned his position as chief chemist and metallurgist of the Cleveland Metal Products Co., Cleveland, Ohio.

Jan 3, 1918

By R. S. Newlin

IN reality, the Butte district is the birthplace of the Anaconda Copper Mining Co., for it was here that strength was gathered and means provided for later expansions of the Company. The Butte district was organized at a miners' meeting on Aug. 20, 1866, primarily for gold placer-mining operations. Substantial amounts of placer gold were recovered from gulch gravels during the period 1862 to 1868. The earliest lode claim locations in the district were recorded in July and August 1864. Copper ore was first shipped, to Swansea, Wales, in 1866. In November 1866, according to the Montana Post, construction of a smelter was started to treat the silver

Jan 1, 1948

By W. C. Ellis, M. E. Fine

WHEN certain binary Fe-Ni alloys are worked cold and then stabilized by a stress-relief anneal, their Young's moduli are nearly invariant over a substantial temperature range determined by composition and work-anneal history.' In the present investigation addition of molybdenum to such alloys (besides increasing the yield strength) was found to diminish the sensitivity of the thermal coefficient of Young's modulus to composition changes. Such alloys are of interest for applications requiring 1 a metal with controlled, low temperature coefficient of Young's modulus and substantial magnetic permeability.' Young's modulus ordinarily decreases with rising temperature. In ferromagnetic alloys a change in modulus on heating due to loss of ferromagnetism modifies the .temperature dependence. Far below the Curie temperature ferromagnetism alters the modulus in two ways: a—Addition of the energy of magnetization, a function of interatomic distance, changes the relation between interatomic energy and distance.' This lowers the modulus in the Fe-Ni and Fe-Ni-Mo alloys of this investigation. b—An applied stress changes the ferromagnetic domain arrangement so that linear magnetostriction contributes to the strain and further lowers the modulUs.~ Since in the alloys of this investigation both effects lower the modulus, loss of ferromagnetism on heating changes the slope of the modulus-temperature curve in a positive direction. With increasing temperature the slope of the modulus-temperature curve, due to progressive loss of ferromagnetism, becomes less negative, goes through zero (the modulus is minimum), becomes positive, and resumes its normal negative value above the Curie temperature.' The increase in modulus and decrease in curvature in the modulus-temperature curve occurring on work hardening have been attributed to a reduction in effect (b).'. Vn the absence of ferromagnetism work hardening through introduction of residual strains would be expected to decrease the modulus.' Alloy Preparation—Test Methods Four series of alloys having nominal molybdenum contents of 5, 7, 9, and 10 pct and containing 47 to 58 pct Fe (the analyzed compositions are given in Table I) were melted in air and cast as bars weighing from 2 to 6 lb. The charge consisted of electrolytic nickel, Armco iron, molybdenum (99+ pct) or ferromolybdenum (62 pct Mo), manganese, and aluminum as a deoxidizer. The bars were swaged cold to the desired diameters with intermediate anneals. Alloys in this composition range are reported" to be face-centered cubic and ferromagnetic at room temperature. The Curie temperatures" decrease with molybdenum. For example, keeping the Ni/Fe ratio at unity and increasing the molybdenum from 0 to 17 pct decreases the Curie tempera- ture from approximately 500°C to room temperature. (The 17 pct Mo alloy requires quenching to retain a single phase.~) Young's modulus at a series of temperatures from —50" to 100°C was determined by a dynamic method previously described.', " In this method Young's modulus is calculated from the resonant frequency (in this case approximately 50,000 cycles per second) of a rod sample (approximately 2 in. long) vibrating longitudinally in the first mode. The densities of the samples at room temperature, Table I, were determined by the standard method of weighing in air and reweighing in redistilled bromobenzene. The linear coefficients of expansion, Table I, needed to calculate the sample length and density at the temperature of measurement, were obtained by observing the change in length (22" to 100°C) of an 8 in. gage distance with a two microscope cathetometer. The values of density and coefficient of expansion in the few samples checked are independent of treatment to the accuracy reported. This was assumed to be general for all the samples. The modulus values are accurate to &0.05x101' dynes per sq cm. However, values of thermal change in modulus are accurate to 20.005~ 10" dynes per sq cm. Young's Modulus Values at 25°C: The modulus values of O', 5, and 10 pct Mo alloys at 25 °C are plotted in Fig. 1 as functions of nickel. After working cold, the samples were either recrystallized at 950" to 1000°C or given a low temperature stabilizing anneal at 400° C. The 400°C anneal does not reduce the hardness nor cause recrystallization. Annealing at 400 °C does

Jan 1, 1952