Search Documents

By AIME AIME

AT A meeting of the Boston Local Section of the Institute, on Oct. 3, approval was voted to the work done by its representatives on the Committee opposing the passage of a bill by the, Massachusetts Legislature to license engineers. The report is as follows: The Joint Committee on Licensing of Engineers, which included a Committee of the Boston Society of Civil Engineers and representatives of seven other societies,* submitted to the members of the respective societies, on Jan. 8, 1921, a report in which it was stated that on Jan. 4, 1921, a petition was filed in the Legislature of Massachusetts by the Boston Chapter of the American Association of Engineers accompanied by a bill to provide for the registration of professional engineers and land surveyors. This report also stated that at a meeting of this committee, held on Jan. 7, 1921, it was voted:

Jan 1, 1921

By Herbert Hoover

THERE is one problem of the new administration that has received the attention and thought of the organized engineers of America for many years past. This is the problem of the reorganization of the Federal Government. The, inadequacy, the wastefulness, and the inefficiency of our federal organization was evident, enough under pre-war conditions. These inadequacies, these inefficiencies, these wastes were exhibited to the country during the war at the cost of millions. Congress has placed the problem in the hands of a very able Congressional Joint Committee, but if this Joint Committee succeeds in securing the imminently necessary results it will only be by full insistent support to it by public opinion. Many attempts have been made at reorganization before but all, of them have gone to the same crematory-the interminable differences in opinion among the executive and legislative officials over details.

Jan 1, 1921

By W. R. Ingalls

Jan 1, 1922

By W. R. Ingalls

Jan 1, 1922

By C. L. HUNTZINGER

THE mine here described is in the Witbank district, a coal area of the Transvaal, about 100 miles north- east of Johannesburg. and is owned by the Witbank Colliery, Ltd. The plant has a capacity of 4000 tons per eight hours, and prepares five sizes of coal. The coal seam lies at a depth of about 200 ft. below the surface, and is reached by an inclined shaft sunk at an angle of 18° with the horizontal. Although the thickness of the coal seam varies from 10 to 14 ft. or more, only about a 7-ft. bench is mined. Mining is by the hord and pillar system. Bords are driven 18 ft. wide, with pillars measuring 18 ft. square. The mine is laid out into four sections, each sewed by a main haulage way from the shaft. Arc-wall machines are used for cutting the coal. but all loading is done by hand. Native labor is employed under the supervision of white miners, who do the required blasting. The workings are practically free from gas and water, and very little timber is needed.

Jan 1, 1931

By Butler, P. B.

TRIPOLI is a rather unusual form of silica, which thus far has been found in commercially valuable quantities only in the neighborhood of Seneca, Mo., although there are numerous deposits of somewhat similar materials in several southern states. The latter have not, however, attained any position of real importance, due undoubtedly to definite structural limitations which have rendered them less suitable for the particular uses that have given tripoli its principal outlets. Raymond B. Ladoo, mineral technologist, says': "Since that time (1880-90) the term tripoli has with increasing definiteness been reserved for the Seneca material, and other siliceous materials of similar origin and physical properties."

Jan 1, 1928

By James W. Wade

THIS discussion of the future supply of lead refers only to the next ten-year period. Beyond that no prediction can be made that would be of sufficient accuracy to serve any purpose. When any commodity is by an unsatisfied demand forced to a higher price level, and the profits of those who are able to produce the commodity are greatly increased, there is awakened a new interest in the commodity on the part of both producer and consumer. The consumer attempts to reduce his costs by developing substitutes or assisting in the development of new sources of supply. Lead is now going through this stage. The lead producer is increasing development expenditure and searching for new mines. The consumer is developing substitutes as illustrated by the increasing use of zinc oxide as a pigment, and the use of dry batteries in radio sets. The search of the Ford interests for lead, by prospecting in Missouri and Idaho, is induced by the effort to develop a new source of supply. Considering the index figures of the Department of' Commerce, it is evident that lead is on a substantially higher price level. For February, 1926, the index figure of lead is 209, while the general commodity price index is only 156, 100 being taken as the base for 1913.

Jan 1, 1926

By H. B. Kinnear

THE first copper stool used under an ingot mold to receive molten steel has recently been taken out of service after it had received ingots amounting to 6012 gross tons. This stool, weighing 8330 lb. had been in continuous service for 1822 heats since its installation. From this modest beginning the use of copper for ingot-mold stools grew to 425,000 lb. in 1934, with an additional 50,000 lb. of copper used in the form of inserts in cast-iron stools. During 1935 the quantity of copper used for stools increased by about 350,000 lb., making a total of 775,000 lb. now in use for that purpose. Copper used for inserts has increased during this time 180,000 lb., or over 350 per cent, to a total of 230,000 lb. The total of copper, therefore, in use at present under ingot molds is slightly over 1.000,000 lb.

Jan 1, 1936

By ANDREW McVILLIAM, WILLIAM H. HATFIELD

AT the 1902 May meeting of the Iron and Steel Institute, the, authors presented a paper on " The Elimination of Silicon in The Acid Open-Hearth," wherein they recorded a few typical examples of certain Siemens charges out of a very large number specially watched for the purposes of that research. The main deductions drawn from those experiments have been accepted in all the intelligent criticism during or after the discussion on the paper. One opinion, however, was rigidly held by all who mentioned the matter, with the single exception, perhaps, of Mr. Lange, and that was the necessity for the attainment and the maintenance of an abnormally high temperature in order that the percentage of silicon in the metallic bath might increase, or that an unusually large proportion of silicon might be retained in the metal. The original decision was ar-rived at on the results of scores of trials, and has since been the subject of frequent experiment. The authors still retain their opinion that although, naturally, a higher temperature will accelerate the (probable) action between the carbon of the steel and the excess silica of the slag, they then fairly proved, and have now abundantly confirmed the fact, that around the temperatures occurring in Siemens steel-making practice the chemical composition of the slag, particularly with regard to its acidity, is the factor which determines whether the percentage of silicon in the molten steel shall increase or decrease. In the discussion in 1902 Mr. Saniter called attention to Mr. H. H. Campbell's work, and in the reply the authors also mentioned that of Messrs. Winder and Brunton of 1892, the two

Mar 1, 1905

By Philip D. Wilson

AS thin most important and vital component of an airplane aluminum hay rapidly become the heart and tome- of the war program. Its production ham increased amt will continue to increase, in comparison with its pre-war position further than that of any of lie other important critical metals except magnesium. Compared with the 1939 production of tons of primary ingot coming from four plants, all owned by the Aluminum Company of America the 1942 figures are more than three timer as large. Including, recoverable scrap and contracted ingot from Canada the 191,, supply of aluminum for the United States will be over siren times dial of 1939- A substantial part of this increase has been achieved during the past year as total production in 1941 was only some 307,500 tons. During 1942 six great new ingot plants sponsored and owned by the Government have come into production and three others are nearing completion.

Jan 1, 1943

By P. L. Weston, S. E. Khalafalla

A systematic study was made by the Bureau of Mines on the effect of so me hypothesized accelerators for the process of wustite reduction in carbon monoxide. When small concentrations of promoter materials in the order of 0.69 at. pct were added to the reducible charge, the rate of reduction to iron was increased. Promotion phenomenon prediction was made in light of a suyface reduction mechanism with the aid of Vol'kenshtein's effect regarding the propagation of crystal lattice disturbances by small amounts of relatively larger interstitial ions. The acceleration produced by a typical promotor, such as potassiunl, increases with protnoter concentration up to a maximum, beyond which the reduction rate decreases. Concentration for maximum promotion depends on the nature and physicochemical properties of the promoter. The extent of reduction rate enhancement is found to be directly proportional to the atomic volume and electronic charge of the additive. DESPITE the enormous volume of literature on iron oxide reduction, very little is reported concerning additive or impurity effects on this important metallurgical process. The beneficial effect bf calcium compound additions on the reducibility of iron oxide sinters has been reported by Tigerschiold,1 vor dem Esche,2 and Edstrom. Doi and Kasai~ found that the addition of lime or limestone to iron ores helps to break up any unreducible compounds, such as fayalite or ilmen-ite. and thus free the combined iron for reduction. Schenck et al. 5 suggested that the increased reduction rate obtained when adding lime could be accounted for by the instability of wustite in the presence of lime. Acid-base slagging reactions resulted in wustite disproportionation according to The dicalcium ferrite formed will yield iron and calcium oxide during reduction. Regenerated calcium oxide dissociates more wustite. This mechanism has been used by Seths and white7 to explain their experimental results. Recently, Strangway and ROSS' attributed the calcium carbonate acceleration of iron oxide agglomerate reduction to increased porosity, both initial as well as that developed during reduction. Aside from calcium carbonate, or oxide, no other promoter was noted in the literature, except for a brief mention by Barrett and woodg on the effect of sodium carbonate and aluminate as activators for the hydrogen reduction of magnetite at 600°C. The present investigation systematically studied a host of other promoters, including calcium and sodium, in an attempt to elucidate the mechanism by which promotion takes place and to fit the results into a simple chemical model. To attain this goal, the effect of promoter physical properties, such as atomic volume, electronic charge, and concentration are related to wustite reduction kinetics in this paper. Wustite reduction to iron, rather than the overall hematite reduction, was chosen since this reaction is known to be the slowest, and hence the rate-deter mining step for the overall iron oxide reduction process. EXPERIMENTAL PROCEDURE Raw Materials and Their Preparation. The pure or impregnated wustite pellets were prepared from minus 400-mesh chemically pure hematite powders. A known weight of hematite was thoroughly and uniformly mixed with a calculated weight of the additive. The mixed paste containing 35 wt pct water was gradually heated from 400" to 1200° C and fired at 1200°C for approximately 4 hr in an air atmosphere. After cooling, the sinter was pulverized to minus 100 mesh and pelletized into minus 4- plus 5-mesh spheres. Pellets were fired, similarly to the paste mix, air-cooled, sized, and stored. An appropriate weight of the charge (20 g) was placed in a zirconia reduction tube maintaining a uniform oxide bed height of 1 cm and a cross section of 7.1 sq cm for all of the test runs. The samples were supported in the vertical reaction tube by a bed of fragmented insulating firebrick plus 3- to 6-mesh alumina beads. The hematite was then transformed to wustite by reduction with a 30 pct CO2-70 pct CO gas mixture at 1000°C in a globar furnace. Complete conversion to wustite was ascertained by a continuous infrared gas analyzer recording the CO-CO2 content of the effluent gas until no carbon monoxide was absorbed from the inlet gas, and inlet-outlet gas analysis remained constant for 30 min. The wustite sample was then reduced with 100 pct CO at 100WC. From the recorded data, an initial rate of reduction was determined by the initial slope of the graph percent reduction vs time. In order to estimate the accuracy of the data, five separate determinations of the reduction curve of pure wustite, under otherwise identical conditions, were performed. The maximum deviation from the average reduction at 14 min amounted to 2 2 pct reduction. This deviation corresponds to 3.8 pct variation based on the percent reduction of the sample. Aiiy impurity effect below the limits of this maximum deviation was considered a spurious result. If the effect exceeded + 4 pct, then it was considered as a positive one. Considerable care was exercised in determining the initial rate from the slope of the initial segments of the curve. Each reduction curve was examined separately on large graph paper and the best tangent to the curve at zero time was drawn. The slope of this tangent was taken as a measure of the initial fractional reduction per minute. Although the time required to reach 50 pct reduction may be of special practical significance, initial rate measurements are invaluable in fundamental studies. These rates provide a measure of the process kinetics on the initial

Jan 1, 1968

By J. J. Carrigan

DURING the experimental stage in our use of the electric cap lamp in the Anaconda mines at Butte. Mont., we were somewhat concerned as to how the spitting of fuses would be carried out if we completely eliminated the open-flame light. This problem was at once given serious attention by the engineering research department and some thought was given to having all blasting done by the use of electric delays, which has been the practice for some years

Jan 1, 1936

By A. B. Kinzel

ALTHOUGH calcium carbide and other compounds of calcium, as well as a number of calcium alloys, are well known and are the basis of important industries in the of United States, calcium metal has been thought of as something of a rarity and has received comparatively little attention from industrial metallurgists. The metal may he made in a number of ways, but the electrolytic deposition of calcium from a molten calcium chloride bath was the first process to be used for its commercial production and is still the standard procedure. Calcium metal has elicited little interest among nonferrous metal producers, as the demand has been relatively small and its production restricted to only a few plants, exclusively in France and Germany.

Jan 1, 1941

By Oliver Bowles

TO keep pace with technical progress is an important function of any industry. All branches of mining may learn important lessons by observing progress made in other branches. The non-metallic mineral industries may learn much from each other as well as from the metal miner and the metallurgist. Recent technical advances which have come to the attention of the Committee on Non-metallic Minerals are presented herewith for consideration and comment. It is planned to present this review for open discussion at the February, 1931, meeting of the Institute. Comments will be welcomed either in the form of written or oral discussion. It is desired that new developments not covered in this paper be brought up at that time. Some notable advances have been made in cement technology. Recognition is now being given to the advantages of closed-circuit grinding of cement raw materials in wet-process plants, with stage removal of the fine materials, It increases mill capacity, reduces the wear of grinding media, and also reduces the power requirement. The method is well known in metallurgical plants, and its acceptance by cement companies is another illustration of the lessons the non-metallic industries may learn from the metal industries. Closed-circuit dry grinding has also proved advantageous for both raw materials and clinker.

Jan 1, 1931

By George W. Powel

IN the nation's effort to raise its magnesium metal supply to meet the ever increasing demand, the Government is relying not only on standard established practice but has extended its support to developments not so well proved-at least, not commercially proved. Within the past few months considerable progress has been made, not only in the definite output of metal but in the exploitation of new processes, the successful adaptation of which should, in a reasonably short time, assure an adequate supply of magnesium. Recent months have also witnessed a reshuffling of the favored methods as well as of the likely raw materials, with the mineral dolomite gaining in interest over its richer but less abundant competitor, magnesite, while the lowly sea water appears to be losing ground to the higher magnesian brines of Michigan and western Texas. Every month sees a new alignment and there are signs that still newer methods or raw materials will be in use before the industry finally stabilizes itself.

Jan 1, 1942

By MERLE HOWARD GUISE

WHEN I was a boy I walked into Fairbanks in 1905. I was but a soft chechako, and arrived with blisters covering my feet, as a result of "mushing" the 400-mile trail on foot. Because of them, the display windows of the trading posts were first to catch my eye-dog and horse collars, harness and sled parts! And because of my enthusiasm for things adventurous, I looked long upon the prospectors' gold pans, shovels, rifles, camp equipment, and what not. Today those windows are filled with motor car accessories, tires and repair parts; yes, even thermos bottles and vacuum cleaners! There were many chance meetings with little parties of prospectors in my youth, and it always set my blood to tingling. Sometimes it was a 70-year-old sun-baked son of the Arizona desert, wrangling his stubborn, faithful jenny away from some outfitting store, at others a shovel-ended poling b0at in northern Canada, \vith the partners and the dogs towing upstream along the bank, or an old sourdough, with tug-rope around neck and hand on the spruce sapling gee-pole, mushing along behind his two or three old, plodding malamutes, dragging a little Yukon sled piled high with rusty sheet-iron stove, pick and shovel, cross-cut saw and axe, rifle, bales of dog salmon, and other paraphernalia. These meetings envisioned the panning of old creek beds and draws in the search for as yet undiscovered pay-channels; they meant the toughest kind of work sinking a hole to bedrock in some far-away valley of promise; they suggested wood fires to thaw the frozen muck and gravel and crude windlass and hand-made tub to hoist the water and the mud; but loudest of all they spoke of Adventure.

Jan 1, 1929

By Max Kraut

UNTIL VERY RECENTLY the flotation process has not found much application in the treatment of gold ores. No appreciable improvement has been made lately in the technology of this application; but the possibilities of flotation have been more fully appreciated. Excellent results were obtained long ago, but few operators paid much attention to them. For instance, in 1915 extensive experiments were carried out by Mr. Beauchamp and Minerals Separation on ores from the Dutch-Sweeney mine near Jimtown, Calif. The ore contained gold-bearing pyrite and laboratory tests indicated a 10c. tailing on a $6 head. In 1918 a 300-ton flotation mill using Minerals Separation machines was built based on the results obtained. However, when the mill began full-scale operation, mill heads did not come up to expectation, being only $4; also the-tonnage was considerably less than had been expected. Flotation mill tailing assayed 15c., indicating a recovery of over 96 per cent, so that excellent metallurgical results were obtained. The operation was a success but the patient died.

Jan 1, 1932

By Charles Will Wright

THE economy as well as the living standards of a country depends largely upon adequate supplies of raw materials at reasonable prices. Geological and climatic conditions responsible for the occurrence of commercial minerals and the growth of raw agricultural and forest products are so varied in different parts of the world that no country can be self-sufficient. The world is rapidly shrinking because of improvement in transportation facilities, but populations are steadily increasing and so are the needs for a greater production of raw materials and for their more equitable distribution. Too many barriers between nations prevent free access to the main sources of supply of the raw materials vital to neighboring nations and it is just such barriers that are often the cause of friction and even war. The International Trade Organization is doing a commendable job in helping to. break down barriers and to reduce friction, and we should now find ways to facilitate access to these sources of supply and encourage more efficient and greater production of the raw materials so urgently needed throughout the world. This cannot be done by individual selfish governmental agencies, influenced as they are by politics, nor by socialistic governments attempting to nationalize industries. It can be done efficiently only by the free individual through private enterprise properly protected against adverse governmental action. This protection can be supplied by the World Bank.

Jan 1, 1948

By Earl Oliver

IN times like these, the A. I. M. E. and similar societies have their greatest usefulness. . . . Individuals and companies acting alone in the development of public opinion are merely voices crying in the wilderness. United and organized they make a great force that can and does influence public action. . . . What part, if any, then, shall the A. I. M. E. take in these great stabilization processes of civilization? Shall it help to give direction and force to scientific knowledge which comes within its field of activity or shall it merely develop more of it? . . . Is it the A. I. M. E.'s function to help bring system, order and direction out of this situation so that the world can again have forward economic movement, or should it rest on its oars until other agenciess develop that public understanding and direction so necessary for economic progress? As we understand the functions of the A. I. M. E. Petro¬leum Division, they are to discover and promote knowl¬edge for the benefit of society on the mining of oil and gas. To the individual member of the Petroleum Division, there are certain advantages of social and professional contacts, but the collective purpose is that described. And the individual is benefited by membership only as the Division measures up to the purposes of its existence. Consequently, the welfare of this Division and that of its members depends on the extent to which it keeps pace with the needs of society on matters relating to the mining of oil and gas.

Jan 1, 1932

By WALTER S.

(New York Meeting, February, 1912,) THE earliest example of attempting to form finely-divided materials into larger masses for better adaptation to commercial use was probably the briquetting of peat and lignite-waste at Paris by the use of a clay binder. It was from this attempt that our word briquette has arisen (Fr. la brique), the formed masses being shaped similar to ordinary bricks. This term does not, however, lend itself to the many shapes of such formed material as are now being produced, as few of them aside from some of the European brown-coal products bear any resemblance to the shape of that well-known article. The term "agglomeration " has therefore been chosen as more accurately descriptive of the products now being manufactured, this term including the molding as well as the sintering. With the increasing prices of fuel and ores and the greater demand for economy in the operation of industrial plants, more ,attention has been paid in recent years to the utilization of waste products and low-grade ores and fuels. Much of the waste has been occasioned by the inability to utilize finely ,divided ores and fuels in the furnaces because they could not be kept there, or else because they clogged up the furnace-shaft so that gases could not be forced through under ordinary conditions of operation. As a result, all such fines were thrown on the dump. Again, with the exhaustion of the richer deposits of ores, concentration of lower-grade ores becomes a necessity, and most concentrates are produced in a finely-divided condition. Aside from these considerations, there is also the economy in the cost of operating the plant; a furnace running on agglomerated material will have a much greater output than one working on fines. In one instance the charge of an iron blast-furnace was changed from fine concentrates to briquettes and the output was increased four-fold; better results could have been obtained had facilities been at hand for taking care of the increased output.

May 1, 1912