Search Documents

By C. R. Kuzell

ALTHOUGH furnaces constructed of refractory brick have been oper-ated for many decades, there has always been an unfulfilled desire by the operators for a less arduous and more satisfactory method of patching weak spots and burned-out zones in order to postpone and to effectively extend the termination of a furnace campaign. Not only has this desire frequently arisen when small spots have approached incipient failure while the furnace structure as a whole was still in good condition, but also when larger areas showed signs of needing replacement. The availa-ble methods have been arduous, sometimes dangerous, inefficient with respect to the life of new refractory material used, and nearly always have necessitated interruption of the continuity of the furnace operations and therefore reduction in furnace production during the period of time required for the repair work. Most of these older methods have involved the replacement of masonry by refractory shapes in the weakened areas. Many attempts have been made to develop a method of patching the burned-out areas by spraying granular refractory material upon old surfaces. While some success has been attained in attempts to renew the grooved, corroded side walls and fettling, and the edges of hearths, there have been no known successful applications of the spraying method in patching the underside of arches of operating furnaces. The method developed recently at the Clarkdale smelter of the United Verde Branch of Phelps Dodge Corporation, at Clarkdale, Ariz., and described in this paper, has been found to be not only convenient and successful with respect to patching vertical or inclined surfaces, but has met with a marked degree of success in patching the parts of furnace arches that are exposed to flame, the successful result being obtained with-out interruption or interference with the continuity of furnace operations. ? It may be described as a method of renewing the interior refractory sur-faces of operating furnaces by pneumatic spraying of an aqueous suspen-sion of finely divided particles of refractory material. It has been used

Jan 1, 1939

By M. W. Fabjanczyk, E. G. Alexander

INTRODUCTION The purpose of this paper is to summarise development of design processes used in the 1100 oreoody as a result of experience encountered. Design methods have been developed as a result of the history of ground behaviour, free-standing qualities of cemented back fill and mass blasting techniques. This paper contains an historical review of design methods previously described by Matthews ( 1972 ) , Hornsby and Sullivan (1977 and 19781, Kirkby, Blair and Hutton (19781, and Stewart (1980). The reasoning behind design philosphy changes are discussed and placed into context with methods now adopted. The 1100 orebody is Mount Isa's main producer of copper ore (5 million tonnes per year ) . Proven reserves are 120 million tonnes at 3.2% Cu. Location of the 1100 orebody in relation to overall mine geometry was well described by Dayton (1976). Geology The orebody is located in a series of massive brecciated shale lenses, in either a siliceous or dolomitic matrix, surrounded and separated by a uniform shale sequence. The whole formation is truncated at depth by a faulted contact with a greenschist facies metamorphic sequence below (Figure 1 and Figure 2) Mathias and Clark (1976). The breccia is known locally as silica dolomite and contains nearly all the economic mineralisation. Interfingering of shale and breccia often results in irregular boundaries to the silica dolomite and the ore limits. Geometry The geometry of the orebodies is shown by Figures 1, 2 and 3. Figure 3 also shows the location of the copper orebodies in relation to the lead orebodies. Structure Although the orebody is contained within the massive breccia (u.c.s. 150-250 MPa), it is cut by shear zones sub-parallel to the regional bedding (north-south striking, dipping approximately 60o to the west), and diagonally by major transverse faults (Figure A). These major faults have continuity in excess of 300 metres, with varying amounts of displacement up to 200 metres, and are zones of potential movement.

Jan 1, 1981

By Wilbur H. Grant

THE property of the United Comstock Mines Co. lies in the eastern foot-hills of the Sierra Nevada Mountains, in the Washoe mining district of Storey County, Nev. Commencing at the boundary line between Virginia City and Gold Hill, covering all the town of Gold Hill, it extends south to American Flat; the main camp, or the new town of Comstock, the mills, shops, residences of employees, and the main haulage-tunnel portal are located on American Flat. The property extends for about 10,300 ft. along the lode; this covers the southern end of the main Comstock lode, the Knickerbocker branch, and the junction of the Silver City branch with the Comstock lode. Within the property, 5000 ft. of the main Comstock lode is known to have been productive, 1000 ft. of the lode at the northern end of the property is thoroughly developed, and 1000 ft. south of this is partly developed; this leaves about 3000 ft. of the known productive portion that has not been opened up by this company. The northern end of the property, or the Imperial mine, has been intricately developed by five main levels and numerous sublevels. The Yellow Jacket ground to the south has been partly developed by the reopening of three old levels. In addition, the main haulage level is driven from the portal at Comstock for 9250 ft., to the north end of the property; about 5500 ft. of this `is in the foot wall of the lode and parallel to it.

Jan 11, 1922

By B. Chalmers, Stefan Wojciechowski

Rotary oscillation of the mold has been used to produce mechanical stirring of the melt during unidirectional solidification. Al-Cu alloys (1 to 4 wt pct Cu) were solidified to study the influence of alloy composition, temperature at which intensive cooling was initiated, and intensity of stirring on the temperature distribution in the sample, the resulting structure, and the copper microsegregation at the columnar to equiaxed transition. The Proposed explanation for the equiaxed solidification in stirred castings consists of the melting off of dendrite fragments, their partial remelting in hotter liquid, and the subsequent growth of the surviving part when the temperature of the melt is lowered. This may result in the formation of a crystal network, which can stop the growth of the columnar crystals and produce the equiaxed zone. It has long been known and many times affirmed that ultrasonic vibrations or relative motion of liquid and solid can significantly reduce the length of the columnar zone and refine the grains in the equiaxed zone in ingots and castings. Because of the technological importance of these phenomena many investigations have been conducted in which ultrasonic energy or mechanical vibration,1-6 electromagnetic stirring,7"10'17 magnetic stirring,"'12 or mechanical stirring13'14 were used to produce the relative liquid-solid motion. More recently, the question of the importance of natural (or thermal) convection has been raised.15-l7 Several possible mechanisms have been suggested.l,8,18-20 They can be divided into two main groups. The first group includes such nucleation hypotheses as nucleation frequency enhancement due to cavitation at the mold wall or other surfaces; cavita-tion in the body of the liquid resulting from the pressure wave, or an agglomeration mechanism, which involves the formation of nuclei by the accretion of subcritical nuclei. The second group considers the grain-refining action to be due to crystal multiplication phenomena such as the removal of the dendrite fragments by viscous forces or by a high-pressure cycle following cavitation or by a melting-off process. Sbme recent investigations give good experimental support to the melting-off proposa1.21-23 The purpose of the present study was to examine the effect of mechanical stirring during the unidirectional solidification on the structure of alloy samples and on the solidification variables. The motion of the liquid was produced by rotary oscillation of the mold around its vertical axis.

Jan 1, 1969

By Herbert R. Mosley, Paul M. Tyler

STRATEGICALLY situated in almost the heart of the leading fertilizer- consuming area of the United States, Tennessee long has ranked second only to Florida as a phosphate-producing state. Since 1932 its share of the national output of phosphate rock has increased steadily, and in 1937 its production mounted to an all-time record. More significant even than the increase in tonnage are the forward strides in technology. The Tennessee Valley Authority's research program has led to quasicommercial operations using hydroelectric power to manufacture concentrated phosphatic fertilizer that is used to further the farmer education program designed to streamline the fertilizer business and halt the appalling waste of farm land by soil erosion. Even more stimulating to chemically minded imaginations is the production of elemental phosphorus by a private company that not only has succeeded in extracting it from the phosphate rock in electric furnaces but actually has contrived to capture it and to transport it safely in tank cars. New values have been created for low-grade phosphate deposits, and the economic life of reserves has been lengthened while the waste of former years goes back into the mills for recovery of its values by modernized methods. Tennessee's phosphate-mining industry dates from the discovery of blue rock in-lewis County in December 1893. Its known reserves are of the order of 101,500,000 tons, which compares with the production of 825,099 tons in 1937; that is, 21 per cent of the phosphate-rock output of the whole nation. The total output reported from 1894 until July 1, 1938, was approximately 19,000,000 tons. Official estimates of reserves are overly conservative and evidence submitted before a joint Congressional committee in November 1938 places "probable" reserves at more than 6,000,000,000 tons.

Jan 1, 1939

By S. F. Emmons

IT was said by many who discussed Professor Posepny's admirable paper on the " Genesis of Ore-Deposits," read at the Chicago meeting of the Institute, in 1893, that its most valuable feature was the clear distinction which it drew between the influence upon ore-deposits of the "vadose " circulation of waters descending directly from the surface, and that of the deep underground circulation of waters generally coming from the depths, and assumed by the author to be ascending through more or less open spaces under the influence of heat. A little later the effect of the oxidizing action of the vadose circulation upon ore-deposits was ably and exhaustively treated by Prof. R. A. F. Penrose, in a paper on " The Superficial Alteration of Ore-Deposits "f-the only one, so far as I know, which has been exclusively devoted to this important subject. My own first detailed study of ore-deposits was made at Leadville, in 1880, at a time when almost the only minerals visible in those deposits were in oxidized forms. That this form was the result of the alteration of earlier sulphides by surface-waters had to be proved at the time by induction or analogy, the general correctness of which was, however, abundantly confirmed by subsequent developments. Thus I was early impressed with the importance of distinguishing, in the study of an ore-deposit, the alteration-products, resulting from the action of oxidizing waters descending from the present surface, from the earlier-formed sulphides; and, assuming that the latter were primary or original, I called the former secondary. I also went so far as to say$ with regard to oxidized ores passing into sulphides in depth "So generally is this accepted as a rule in ore-deposits that it would require special demonstration to prove beyond a doubt that the native metals or their

Jan 1, 1902

By F. L. Kadey

The petrographic microscope is a well known tool in nonmetallic materials research. Its utility in the study of perlite is, therefore, not surprising. Valuable information has been derived on samples smaller than those needed by most other methods of analysis. Relatively little has been written about the petrographic analysis of perlite for two chief reasons: perlite is a material of relatively new commercial interest; and the independent prospector or expander, responsible for most studies, attacks the problem from an immediately practical viewpoint. Hence, petrographic studies of perlite have been limited to academic aspects. Rapid development of commercial interest in perlite has changed the situation. Mining and expanding companies now have effective research tools; and such instruments as the petrographic microscope have added materially to practical knowledge about this mineral. Petrographic techniques employed in the search for suitable deposits screen worthless samples rapidly and inexpensively compared with large-scale expanding tests. Hence, only samples of potential quality are selected for further testing. Field appearance of perlite reveals little about its true identity and practically nothing about its commercial significance. Consequently, any method that can be used to separate the "wheat from the chaff" is valuable. In addition to the conventional thin-section and immersion methods used in evaluation of crude perlite, petrographic microscope techniques have contributed to the study of expanded perlite. When apparently similar materials behave as differently in use as perlites, the internal structure of the individual particles becomes a subject of great interest. The purpose of this paper is to discuss some of the petrographic techniques used to characterize this material. WHAT IS PERLITE AND WHERE IS IT FOUND? Perlite was at first described as a glassy rhyolite possessing a pearl-like luster and exhibiting numerous concentric cracks resembling an onion skin appearance.' Fig. 1 is an illustration of perlite in this classical sense. Recently, its definition has taken on a commercial connotation: an acid volcanic containing 2 to 5% of combined water that, when heated rapidly to the softening point of the glass, coincident with the volatilization of the combined water, expands or "pops". Fig. 2, although hardly fitting the classical description given by Johannsen, is an excellent perlite in the commercial sense. It may occur as a breccia in rhyolite, (Fig. 3) and sometimes it is associated with obsidian nodules, as illustrated in Fig. 4. The term perlite includes the expanded product also. In the United States, perlitic rocks are restricted to the western part of the country. 2 Elsewhere in the northern hemisphere, European occurrences follow a belt beginning in Iceland and extending in a southeasterly direction through Scotland, County Antrim in Northern Ireland, and through the Massif Central of France, Germany, and Hungary; thence, into Italy and Sardinia, and through some of the Aegean Islands. A general oriental belt extends from Japan through Australia and New Zealand. Rhyolitic areas elsewhere in the world undoubtedly contain perlite.

Jan 1, 1963

By Heinrich Freyn

THE American iron and steel manufacturer finds himself to-clay barely at the threshold of enormous possibilities for practicing rational economy in the use of fuels. The fuel cost is by no means the smallest of items which enter into the cost of manufacture of iron and steel products, but the great wealth of this country in high-grade fuels, together with a protective tariff, has heretofore made fuel economy relatively unimportant. In Germany, the use of raw coal for the purposes of iron and steel manufacture has been all but abandoned and large sums of money, formerly irrevocably wasted, are now being saved. When scanning the literature of this country devoted to the application of gas power, but little information will be found on a subject which, however, is destined to become of considerable importance in the United States, namely, the use of coke-oven gas for the generation of power in gas engines. This lack of information can be traced to the fact that the regenerative by-product coke oven with its large amount of surplus gas is still far from having attained in this country the universal application which it has found in Europe. This statement needs hardy any corroboration other than the evidence of statistical investigations made by E. W. Parker of the United States Geological Survey, according to which only approximately 25 per cent. of the total coke produced in this country in 1912 was made in by-product coke ovens, whereas 75 per cent. was produced in bee-hive ovens. This entailed the enormous loss of over $80,000,000 in non-recovered by-products, such as gas, tar, and ammonia, without considering the substantial loss due to the non-recovery of benzol from the coal. There are two more or less distinct fields of application of the by-product coke oven: one, to furnish as the main product metallurgical coke of specified quality, and surplus coke-oven gas as the by-product, and the other, to carbonize high-volatile coals, and thus produce as the main product large quantities of gas, high in heat value and rich in illuminants, adapted primarily for domestic heating and lighting, while domestic coke becomes the by-product.

Jan 4, 1914

By Thomas MacFarlane

I. INTRODUCTION. AMONG the industrial enterprises which have, from time to time, been undertaken in our Dominion, few have been more uniformly unsuccessful than those which have had for their object the development of our mineral resources. These resources have not been regarded as insignificant. On the contrary, it is supposed that we possess in our ore deposits something more than mere points of mineralogical interest. Some people are enthusiastic enough to believe that our mineral wealth will yet occasion the establishment in our backwoods of happy and industrious communities, causing, in fact, our wilderness to blossom as the rose. These enthusiasts do not shut their eyes to the serious obstacles which at every stage interfere with the carrying out of mining enterprises in this country, and which tempt one to believe that no such enterprise can ever be conducted to a desirable end, but they entertain the conviction that as our capitalists, miners, and technologists reach the years of discretion, and handle our mines in an economical, vigorous, and judicious manner, and as our statesmen become alive to the necessity of fostering, without extremely protecting, our metallurgical industries, mines and furnaces will gradually prosper, and so develop as to become a tower of strength to our agricultural, manufacturing, and mercantile interests. The fact that our past experience does not generally justify such glowing anticipations makes one all the more anxious to put on record the history of a successful mine, such as the Silver Islet has, on the whole, been. My connection with its discovery and early development was a very intimate one, and I propose in this paper to sketch its history and character, and sum up the amount of silver it has so far yielded. An additional reason for the appearance of this paper is that the Transactions of the Institute contain only a few references to the Silver Islet Mine. Although this mine is reported successful, we have, of course, no guarantee that it will not fall a victim to the same influences which have

Jan 1, 1880

By M. Sagheer

This paper gives a report of the laboratory work investigating the fundamental flotation characteristics of chromite and its commonly associated mineral, serpentine. Floatability curves, showing floatability of chromite at different concentrations of sodium oleate and pH, were obtained by pick-up method. One of the difficulties encountered in flotation of chromite in presence of serpentine has been attributed to dissolved metal ions. The influence of metal ions, dissolved in pulp filtrate, on floatability of pure chromite and serpentine has been studied and it has been shown that Mg, Ca and Fe ions depress chromite. A considerable amount of work applying bubble pick-up method was carried out to counteract the depressing action of metal ions. Various methods and reagents were applied in this connection. Validity of each method and reagent has been discussed. Probably due to the abundance of high-grade chrome ores, very little has been published concerning the flotation of chromite. As improvements in mineral beneficiation are realized, more attention is being directed to low-grade ores previously considered unusable. Currently, gravity concentration is the principal process applied to upgrade chrome ores, but this cannot be used for finely disseminated ore because of the substantial losses in the fines,1,2,3 To avoid these losses, flotation can be applied to material which is too fine for satisfactory gravity concent ration, and it is probable that a combination

Jan 1, 1967

By Thomas A. Read

The internal friction of single crystals of metals is affected markedly by a variety of factors, which, according to the literature, are without influence on the internal friction of polycrystalline metals at strain amplitudes less than 10-5. For example, the internal friction of a suitably oriented zinc single crystal is multiplied by a factor of ioo when the vibration amplitude is slightly increased, and the internal friction of a copper crystal is markedly increased by the application of a stress of 30 lb. per sq. in. for one minute. In this paper it will be shown that these, together with the other phenomena associated with the damping of mechanical vibrations in metal single crystals, can be satisfactorily explained, at least qualitatively, in terms of an atomic mechanism that has been proposed for quite another purpose—that of accounting for slip in metals. The extraordinary agreement between the observed behavior of the metal single crystals and the behavior that could be predicted on the basis of this atomic mechanism leads to the belief that the latter is probably essentially correct. If this is so, it follows that valuable information about the slip process in metals may be gained from measurements of internal friction on single crystals. In this paper the results of the only study to date on the damping of mechanical vibrations in single crystals of metals mill be presented. Experimental Procedure The internal friction of a material is a measure of the rate at which the energy of mechanical vibrations is converted into heat. The measure of internal friction used in the present paper is the decrcment A, which is defined as the fraction of the energy of vibration lost per half cycle. The measurements described here were made for longitudinal oscillations at a frequency of 33.5 kc. for the copper crystals, and at a frequency of 39 kc. for the zinc crystals. The method used is that of the composite piezoelectric oscillator. The single-crystal specimens are in the form of circular cylinders M in. in diameter and I 1/2 to 21/2 in. long. The crystal rods are waxed in a V-block and sawed to the proper length with a fine jeweler's saw. The ends of the specimen are ground flat, and one end is cemented with a very thin film of beeswax and rosin to the end of an x-cut quartz rod which is 1/4 in. in diameter and 3 in. long. The length of the specimen rod is determined by the condition that its natural frequency for longitudinal vibration be the same as that of the quartz rod, within 0.5 per cent. The lengths of the specimens are thus different for different orientations of the cylinder axis with respect to the crystallographic axes. When the specimen and quartz rods are thus matched in frequency the adhesive is at a node of stress, and it has been shown experimentally that under these circumstances

Jan 1, 1941

By Thomas S. West

A gravel pack completion is described which, in addition to sand screening, permits the exclusion of water and gas from the oil production. A gravel pack composed of alternate layers of different particle sizes is employed which has horizontal but not overall vertical permeability to drilling mud. A packer is run on the tubing and set in the screen member, around which the gravel layers are placed. The hydrostatic pressure of a mud column prevents the entry of fluid above (or below) the level of the packer. The producing level may be changed by raising or lowering the tubing. Vertical coning is controlled by replacing the mud column with oil and continually injecting oil into the sand section above (or below) the packer. Three well histories with this completion are described in detail. Statistics on the first 100 completions of this general type are given. INTRODUCTION Gravel pack type completions have heretofore been almost exclusively for the purpose of preventing sand production. This paper describes and presents well data on a gravel pack procedure which is primarily a selective completion method. Although complete sand screening is achieved, the exclusion of gas and water is the primary objective. The application of this procedure is therefore not limited to unconsolidated sands. Application to hard sand or limestone reservoirs is equally feasible. GRAVEL PACK PROCEDURE Figs. 1 and 2 illustrate the gravel pack procedure employed. The gravel is placed by means of the frangible disc type dump bailer shown by Fig. 1.' This bailer has its lower end closed by a plate glass or steel rimmed cement disc. This disc breaks when the bailer passes over the liner allowing the gravel to be deposited around the liner. The liner employed is usually 2 3/8 in. to 2 7/8 in. OD and 1.995 in. or 2.07 in. ID (ID of 2-in. tubing or 2-in. line pipe). Two tvDes,. of slotted sections have been employed. One type employs horizontal hacksaw cut or milled slots of about 1/32 in. width opposite the producing section. The other type employs the same type,. of horizontal slot. but slots are placed in groups of six at intervals of about 8 in. A cage composed of half round vertical bars, spaced apart, is then welded to the pipe over the slotted sections. This liner has the bottom end closed, usually by bull plugging. The upper end is closed, while placing the gravel, by a cap which is held in place by means of a shear pin. This cap has a mandrel attached to it which extends downward inside of the liner to within a few inches of its lower end. The top of the liner cap is formed to fit a releasing type wire line core barrel overshot. The liner is lowered to bottom on the wire line by means of this overshot and released. The length of the liner is usually suffi- cient to extend to about 20 ft above the highest level to which gravel is to be placed, the upper end of the liner always being in the casing. The dimensions of the liner and bailer are such with respect to the casing size that the bailer will always pass over the liner. After releasing the liner the bailer is run to bottom. Passage of the empty

Jan 1, 1951

By George R. Elliott

Methods are presented for measuring and comparing "degree" of water drive, and for observing the control that rate of withdrawal exerts over decline of reservoir pressure. Degree of water drive is studied from pressure-production curves of 10 reservoirs; the method used to present these comparatively is to convert cumulative oil production from barrels to percentage of ultimate. Degree of water drive is also represented by a "water-encroachment factor," representing barrels of water influx per pound-month per acre-foot of oil reservoir. Pressure-production curves for the water-drive reservoirs after a period of declining pressure show a diminishing angle of slope, in some cases to the point where pressure ceases to decline or where it even increases; the shapes of these curves are in marked contrast to the dissolved-gas type of curve, which shows a general trend toward zero pressure at ultimate oil recovery. Yearly rate of oil production in percentage of ultimate oil recovery is correlated with pressure decline. The correct rate of production of oil with its associated gas and water sustains pressure in reservoirs having a high water-encroachment factor. For reservoirs having a low water-encroachment factor, it is necessary to inject the produced water and even inject large volumes of water from an outside source. The discussion of the actual reservoirs is preceded by a general review and is followed by a substantial bibliography. It is now generally accepted that water drive is capable of yielding 60 to 80 per cent of the original oil in place in most reservoirs, as compared with 20 to 40 per cent for dissolved-gas drive. There is no need to question the importance of controlling a reservoir in order to take advantage of such an efficient mechanism. What is a water-drive reservoir? Oil reservoirs usually combine two or more of the four basic mechanisms: dissolved-gas drive, gas-cap drive, water drive, gravity drainage. A water-drive reservoir is one in which water advances to take the place of the oil and gas produced. When the oil withdrawal rate is sufficiently low, the water will tend to maintain pressure. The maximum effectiveness is attained when the water follows the oil withdrawal so closely that little or no decline in pressure occurs. Oil in its underground reservoir is associated with water. This water is significant in the production of the oil according to the source of supply and the permeability of the surrounding formation. As oil is produced and the pressure is lowered, water can move in to replace the oil. With adequate supply and sufficient permeability, actual movement takes place on an extensive scale. The first movement of water takes place by expansion of the water and its associated fluids. While this expansion is of little importance in some fields, in others it is sufficient to supply all of the energy required for the production of oil. When a pressure differential has been established

Jan 1, 1946

By H. H. Kaveler

Education is for the purpose of developing citizenship, and, if it is pursued for the additional purpose of preparing for a professional career, such as engineering, it is also directed to developing a knowledge of essential science, aptitude for the application of science to practical situations, and a knowledge of the industrial art in which the engineer will be engaged. The process of education required for engineering must of necessity extend beyond the classroom into industry. For that reason, the education of engineers should be divided as between the university and industry. Specialization in engineering should logically come as a result of experience in an industry. The student cannot take the time in a university, and, the university cannot teach the skills required to develop a specialist without sacrifice to the more essential broad purposes of formal education. In addition to talent in science, aptitude in the application of scientific fact, and knowledge of the industrial art, the engineer should possess certain personal qualities which are helpful in the pursuit of a professional career. Those personal qualities are: the ability to work as a partner in an enterprise, the ability to do jobs in a way whereby job performance is a means of gaining experience and increased responsibility, the capacity to write and speak in an understandable manner, and, a Proper regard for the "significance of answers." These pcrsOnal qualities may be of almost equal importance to acabemic accomplishments in the field of science. Development of such personal qualities are an essential part of the student's training in the university and in industry. They can be developed effectively through the leadership of instructors. Compulsory Education Nature played a mean trick On the human race when the evolutionary Process failed to develop in the individual a capacity to inherit knowledge. Were knowledge transmissible in a cumulative manner from generation to generation, mankind would be by inheritance wise beyond measure within a few generations. Then there would be little if any need for a "system of education." As matters stand, however, all must suffer the burden of starting life at the "zero " level of learning from which station each rises depending upon individual capacity to assimilate knowledge left of record by our predecessors and the individual effort exerted to compensate for Nature's failure to endow the offspring with intelligence. In the United States some degree of education is generally regarded as essential and necessary. Therefore, all citizens are subjected by law to an educational process covering the primary school age from six to sixteen years. Beyond the schooling required by law, many attend secondary schools, and beyond that, schools of higher learning. Our standard of living is at a level that permits an increasingly large fraction of the population the opportunity to go through all of the formal educational process. As a result, education in the colleges and universities has almost reached a mass production level. In spite of the high

Jan 1, 1949

By Louis A. Rosales, Kanji Ono

The anomalous behavior of hydrogen in iron is examined and a new model is proposed It is postulated that hydrogen single and di-interstitials are in equilibrium with each other. When the binding enthalpy of the di-interstitial, B, is assumed to be about 10 kcal per mole, the predicted temperature dependence of the solubility agrees reasonably well with the reported data. Effective diffusiuity is calculated assuming the di-interstitials to be immobile. Since the number of mobile single interstitials is greatly reduced at lower temperatures, the effective diffusivity is decreased. A good agreement in the temperature dependence of diffusivity between theory and experiment is provided with B - 10 kcal per mole. The predicted diffusivity is also a function of total concentration of hydrogen and this appears to be Partly responsible for the large scatter in the reported data. HYDROGEN is known to form an interstitial solid solution with iron.''' At elevated temperatures, it has been well-established that hydrogen enters iron in the dissociated form and occupies the interstices, and that diffusion of hydrogen in iron is via the interstitial mechanism. The concentration, c, permeability, P, and diffusivity, D, of hydrogen in iron have been separately determined and are consistent with each other under the steady-state condition for temperatures above approximately 400°C; that is, the relationship P = c-D holds. At lower temperatures, however, anomalous behavior of hydrogen in iron has been observed by many investigators. The results of experimental studies4-'' of the diffusion of hydrogen in iron are summarized in Fig. 1, in which the values of D are plotted against the reciprocal temperature. Although there is an increasing divergence in observed values of D with decreasing temperature, the values of D at temperatures below approximately 200°C are definitely small as compared with the extrapolation from high-temperature data. The lines shown bracket the region containing the most probable data. The observed values of c6," are plotted against the reciprocal temperature in Fig. 2, where the dashed lines represent Geller and sun's'' most probable isobars at 1 and 100 atm. At high external hydrogen pressure and low temperatures, the values of c observed are higher than those expected from high temperature data. It is generally accepted that certain trapping mechanism is responsible for the anomalies, but the nature of the trapping mechanism has not been clarified. Various types of hydrogen traps were suggested in the literature, such as "rifts" in the lattice dislocations, voids, microcracks, and so forth. However, no quantitative account of the observed behavior has been given in terms of these trapping mechanisms. Formation of methane in hydrogen-charged steel was found by ~odgurski." This appears to explain the existence of the so-called "residual" hydrogen,4 but not the observed anomalies of hydrogen in iron. McNabb and Foster' proposed a mathematical analysis in terms of a trapping mechanism. However, the physical significance of the traps was not clarified. The necessity of evaluating five parameters in their theory made comparison with experiment difficult. In the present paper, a model is proposed in which the anomalous behavior of hydrogen is attributed to the formation of hydrogen di-interstitials at lower temperatures. In this model, it is postulated that single and di-interstitials are in equilibrium with each other. (The hydrogen di-interstitial is to be distinguished from a hydrogen molecule which may exist in voids.) It can then be shown that most of the anomalies can be explained by assuming that the di-interstitials are virtually immobile and that the binding enthalpy of the di-interstitial, B, is approximately 10 kcal per mole. Predictions of the theory agree with the available experimental data reasonably well. THEORY The basic postulate of the present analysis is that single and di-interstitials are in equilibrium with each

Jan 1, 1969

By Jonas Svensson

A new method is described for the production of cold-bonded pellets using a hydraulic binder, such as portland cement. Large-scale pilot-plant tests have proved that self-fluxing pellets of high reducibility and good handling strength can be made by the method. Blast-furnace trials have shown that the pellets are an acceptable burden material, comparable with self-fluxing sinter or heat-hardened pellets. Economic factors of commercial-scale production are discussed. The Grangcold Pellet Process—for which patents have been applied or already granted in a number of coun-tries—uses a hydraulic adhesive such as portland cement, slag cements, pozzolanic cements, etc., for the production of cold-bonded pellets. The idea of using a hydraulic binder for the agglomeration of iron-ore fines is not new. Portland cement was proposed as an adhesive for cold-bonded iron-ore briquettes in patents granted more than 50 years ago.' In a report on the briquetting of iron-ore fines, published in Stahl und Eisen in 1959; it is stated that briquettes bonded with portland cement are used on a small scale at an ironwork in Germany. According to the report, the briquettes showed excellent strength in the blast furnace although their general use was made impossible because they required a long hardening time, during which they are sticky, soft, and difficult to store and handle. The Grangcold Pellet Process has overcome this particular disadvantage by mixing the balls with a suitable amount of the balling concentrate before storing them. The pellets are embedded in the concentrated during storing in such a way that they are isolated from each other and thus prevented from sticking together to form clusters. Thanks to the embedding concentrate, the pellets are subjected to a more or less uniform pressure from all sides which does not deform them. Thus, the mixture can be stored in a stockpile or in a bin until the pellets have hardened sufficiently. The concentrate is separated from the pellets by means of screening. The concentrate is returned to the balling operation and the pellets are either shipped to the blast furnace or stored for final hardening. The binder preferred for the Grangcold Pellett Process is portland-cement clinker, ground without the admixture of gypsum in order to avoid sulfur in the pellets as far as possible. Usually a 10% binder content is used. Two-thirds of the portland-cement clinker consist of lime and the rest is silica, alumina, and ferric oxide. Thus, self-fluxing or overbasic pellets are produced with this binder if the amount of silica in the concentrate used does not exceed 4%. The Grangcold Pellet Process was developed by the mineral Processing Laboratory of the Granges Co. Work started in 1963 with batch-scale tests. In 1966, a small pilot plant was put into operation in which 1800 tons of pellets were produced using 10% of rapid-hardening portland cement as a binder. Favorable results from a blast-furnace test with this batch led to the decision to erect a larger pilot plant which went into production in the summer of 1967. Since then, approximately 100,000 tons of cold-bonded pellets have been produced, mostly with 10% gypsum-free portland cement as a binder. Several full-scale blast-furnace trials have been performed with the pellets. The results of the trials indicate that the Grangcold pellets constitute a satisfactory blast-furnace feed. An industrial plant for the production of Grangcold pellets with a rated capacity of 1.5 million tpy is now under construction at the Granges Co.'s mine at Grangesberg. The plant will come into operation in the summer of 1970. Results from Laboratory Work Pellets made from iron-ore concentrate bonded with portland cement harden slowly and their handling is very critical until they have hardened enough to loose their stickiness. It is therefore especially important to study the progress of the hardening action and the factors influencing it. This is best achieved by investigating the relationship between the compressive strength of the cement-bonded pellets and the curing time under varied conditions. The general course of this relation-

Jan 1, 1971

By A. H. Geisler, F. Keller

Some of the important changes that take lace in the structure of aluminum alloys are largely submicroscopic in character. This is especially true of the changes that accompany age-hardening and recrys-tallization. Although improved metal-lographic practices have been helpful in indicating some of these changes indirectly, results are limited by the resolving power of optical microscope lenses. The electron microscope, however, provides a new and important means for investigating the fine structure of metals in a range not possible heretofore. It is anticipated that this microscope will yield new and useful information to metallurgists when suitable techniques are developed to utilize its very high resolving power. Several unique methods have been devised to permit the examination of the structure of opaque samples by the electron microscope. These are all based 011 the principle of producing a very thin film that represents the prepared surface of the opaque metal sample, which can be examined in the transmission microscope; however, the available methods fall into three categories, depending on the manner in which the film is obtained. With the oxide-film method developed by Mah13-l7 a very thin surface layer of the metallographic sample is converted into oxide by a thermal, chcmical or anodic treatment. .After removal from the metal sample by one of the special techniques described by Evans,l9 this oxide film is examined in the electron microscope, and is found to portray the structure of the original metal surface. Films formed on aluminum,8,l7 nicke1,7 iron3,8,9 and a nickel-beryllium alloyl1 by heating; films formed on iron8,9 by chemical action; and films formed on aluminum3-'" by anodic oxidation, have been examined. The other two are more recent methods developed principally in this country; they consist in making the thin film in the form of a mold or replica of the surface contour of an etched sample. With the negative replica method the thin film is made directly on the sample; with the positive replica method it is made on a negative reproduction of the sample. With both methods, variations in the contour of the metal sample, caused mainly by etching, produce variations in the thickness of the surface replica. Because of the direct dependence of the amount of scattering of the illuminating electrons upon the thickness of the film penetrated, only the variations in thickness of the replica are responsible for tones in the electron image. Negative replicas are made by forming a thin film of some suitable material directly on the polished and etched metal sample, and derive their name from the fact that after removal from the sample they have the high and low points in the sample reversed, as shown in Fig. I. Nega-

Jan 1, 1944

By F. Keller, A. H. Geisler

Some of the important changes that take lace in the structure of aluminum alloys are largely submicroscopic in character. This is especially true of the changes that accompany age-hardening and recrys-tallization. Although improved metal-lographic practices have been helpful in indicating some of these changes indirectly, results are limited by the resolving power of optical microscope lenses. The electron microscope, however, provides a new and important means for investigating the fine structure of metals in a range not possible heretofore. It is anticipated that this microscope will yield new and useful information to metallurgists when suitable techniques are developed to utilize its very high resolving power. Several unique methods have been devised to permit the examination of the structure of opaque samples by the electron microscope. These are all based 011 the principle of producing a very thin film that represents the prepared surface of the opaque metal sample, which can be examined in the transmission microscope; however, the available methods fall into three categories, depending on the manner in which the film is obtained. With the oxide-film method developed by Mah13-l7 a very thin surface layer of the metallographic sample is converted into oxide by a thermal, chcmical or anodic treatment. .After removal from the metal sample by one of the special techniques described by Evans,l9 this oxide film is examined in the electron microscope, and is found to portray the structure of the original metal surface. Films formed on aluminum,8,l7 nicke1,7 iron3,8,9 and a nickel-beryllium alloyl1 by heating; films formed on iron8,9 by chemical action; and films formed on aluminum3-'" by anodic oxidation, have been examined. The other two are more recent methods developed principally in this country; they consist in making the thin film in the form of a mold or replica of the surface contour of an etched sample. With the negative replica method the thin film is made directly on the sample; with the positive replica method it is made on a negative reproduction of the sample. With both methods, variations in the contour of the metal sample, caused mainly by etching, produce variations in the thickness of the surface replica. Because of the direct dependence of the amount of scattering of the illuminating electrons upon the thickness of the film penetrated, only the variations in thickness of the replica are responsible for tones in the electron image. Negative replicas are made by forming a thin film of some suitable material directly on the polished and etched metal sample, and derive their name from the fact that after removal from the sample they have the high and low points in the sample reversed, as shown in Fig. I. Nega-

Jan 1, 1944

By Frederick Laist

About six years ago the Anaconda Copper Mining Co. decided to investigate the possibility of extracting zinc from the ores of certain mines in the Butte district. These ores are of a complex character and contain so much iron and lead that the concentrate contains only 33 to 35 per cent. zinc. Investigations showed that while a high-grade concentrate could not be obtained by ordinary methods, such as tabling and magnetic treatment, a fair grade could be made by the Horwood process. In this method, the concentrate resulting from the flotation of all of the sulfides is given a light roast and this calcine is subjected to flotation in the presence of a large amount of sulfuric acid; the resulting concentrate contains most of the zinc and a residue contains most of the iron. The fact that the lead, copper, and silver are divided approximately equally between the zinc concentrate and the iron residue and the large consumption of acid, which ranged from 50 to 100 lb. (22 to 45 kg.) per ton of concentrates, were serious objections to this plan. The zinc recovery, moreover, was low, as a considerable percentage invariably accompanied the iron. While a profit might be made on the ores by the use of this process, it was thought that other and more promising methods might be devised. After carefully studying the field and doing some laboratory work on various processes that had been suggested, it was decided that the electrolysis of sulfate solutions was the most promising. We soon found, as have other investigators, that the only way to obtain a good zinc deposit is to have the electrolyte free from all metals more electronegative than zinc, such as copper, cadmium, lead, arsenic, antimony, etc. Arsenic and antimony are particularly injurious, causing very poor current efficiency and small yield per horsepower when present in amounts so small as almost to defy detection—1 mg. or less per liter. A pure zinc is soluble only with difficulty in sulfuric acid; an impure zinc dissolves very readily. Electrolytic zinc deposited from pure solutions is, of course, extremely pure and dissolves only about one-fiftieth

Jan 1, 1921

By Lester A. Blackner

The Ray Consolidated Copper Co.'s mining property is located on Mineral Creek, 6 miles north of Kelvin, at Ray, Pinal County, Ariz. (Fig. 1). The mining claims now owned by the company consist of 126 lode claims, comprising 2,144.9 acres, containing at the beginning of operations 82,904,368 tons of 2.19 per cent. copper ore. General Characteristics of the Orebody The main orebody is a disseminated deposit in schist and porphyry formed by secondary enrichment. Its existence was proved by churn drilling, and it is at present one of the largest proved copper deposits in the world. The orebody itself covers 205 acres with an average thickness of 121 ft., and occupies a definite belt which has a northwest direction. Its length is approximately 5,000 ft. The width varies, being about 2,000 ft. at the west end and 2,500 ft. at the east, narrowing down irregularly from both ends to a few feet in the center. The thickness of the body varies greatly along the line of lode, ranging from a few feet up to 470 ft. thick. The ore horizon is not constant, but varies, following in a broad sense the topography. The body in general dips slightly to the northeast, and is broken up by numerous small faults and fractures. The ore-bearing formations, consisting of mineralized schist and mineralized granite porphyry, stand fairly well and offer no difficulty in mining operations. The bulk of the ore is chalcocite disseminated in schist. In places cupriferous pyrite is closely associated with the chalcocite. The mineralized gr'anite-porphyry forhations are contiguous to the ore-bearing schist. • Overlying the orebody is an oxidized zone of leached iron-stained schist, averaging 252 ft. in thickness, termed "capping." The Line of

Jan 1, 1916