Search Documents

By Roy Lindgren

SINCE the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe-rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1936

By James R. Walpole

This paper will discuss the federal laws and regulations that are related to water quality. Both surface and underground water quality issues will be covered as well as point and nonpoint source requirements. Some of the subjects to be covered include the Federal Water Pollution Control Act (e.g., effluent guidelines, nonpoint source requirements, etc.), the Safe Drinking Water Act (e.g., underground injection control requirements; pits, ponds, and lagoons study, etc.), the Resource Conservation and Recovery Act (e.g., mining wastes study, etc.). The importance of related court decisions will also be discussed

Jan 1, 1982

By Bernard Amadei, Richard E. Goodman

A medium is anisotropic if its properties vary with direction. This is the general characteristic of many rocks, for example, schists, slates, gneisses, phyllites and other metamorphic rocks. Bedded and regularly jointed rocks also display anisotropic behavior. This paper is concerned with the influence of rock anisotropy on in-situ stress measurements. It is limited to stress measurements by overcoring techniques for which strains and displacements are recorded either on the walls of a pilot hole at the end of one or several boreholes or within instrumented solid or hollow inclusions perfectly bonded to the surface of the pilot hole. The rock is described as homogeneous, continuous, anisotropic and linearly elastic. The following questions are answered with special emphasis on rocks that can be classed as transversely isotropic or orthotropic: the number of independent measurements obtainable in a single borehole; the number of boreholes required to determine the in-situ stress field; the influence of rock anisotropy on these numbers; the influence of the anisotropy type and the error involved by neglecting rock anisotropy.

Jan 1, 1982

By C. F. Smart

Since their comparatively recent development, the alloys of cadmium with silver and copper or nickel, and of cadmium with nickel alone, have been used somewhat extensively as liners for connecting rod bearings and main bearings of internal-combustion engines. In applications where, owing to high bearing loads and elevated operating temperatures, the life of bearings made from tin-base or lead-base alloys has been undesirably short, cadmium alloys have demonstrated considerable advantage. In applications where, because of deflection of the crankshaft or bearing supports, copper-lead bearing metals have resulted in scored shafts, cadmium alloys have been operated successfully. The somewhat serious drawback to these alloys in bearing service has been that they, in common with copper-lead and certain lead alloys, are susceptible to corrosion in the presence of lubricants containing organic acids. These acids may be fatty acids (such as oleic acid) derived from animal or vegetable oils that sometimes have been compounded with engine lubricants, or they may be compounds of an acid nature developed by the oxidation of some petroleum oils under operating conditions. The result of such acid attack on bearings is illustrated by the photograph, Fig. 1. The petroleum oils that are most readily oxidized to a corrosive condition, and the operating conditions under which such oxidation most readily occurs, are now rather well known among the technical organizations of both the petroleum and automotive industries. While means have been developed for inhibiting petroleum oils against such acid formation, the knowledge that this condition may be encountered has been a factor in restricting the wider use of cadmium alloys as engine bearings. It has appeared, therefore, that their value and use would be enhanced if they could be made corrosion-resistant to a degree compatible with the most severe operating requirements. Investigation, undertaken with this in view, indicated that the addition of fractional percentages of the metal indium to the cadmium bearing

Jan 1, 1938

By Alexander Squire

A BRIEF study of the effects of material and processing variations upon the tensile properties of steel formed from mixtures of iron and carbon was made in order to provide information regarding the .properties obtainable in iron-carbon compacts as influenced by forming pressure, sintering temperature, and graphite particle size. Sintered steels formed from mixtures of iron and graphite have been studied by Stern,1 who investigated the effect of various percentages of graphite on compacts formed from electrolytic iron that were repressed and heat-treated after sintering. A further study, by Stern and Greenberg,2 is concerned with the heat-treatment of steels formed by the carburization of iron compacts, and Margolies3 has reported work on the simultaneous sintering and carburization of iron-powder parts. Glauch4 investigated the effect of various types of graphite on the properties of iron-carbon powder alloys but did not determine the effect of different particle sizes of the same graphite alloyed with different types of powder. In the investigation reported in this paper, powders typical of those produced by electrolytic deposition and the decarburization of shotted steel scrap were used. The powders were mixed by tumbling in a jar mill with graphite powder ground to an average particle diameter of 2, 4, 6, and 16 microns (as determined by microscopic measurement). The properties of the iron and graphite powders are presented in tabular form as Table I. In order to obtain the maximum information from a minimum number of test specimens, the study was divided into two sections with one set of specimens treated identically in each section as a basis for comparison. In the first section, iron powder produced by the shotting and subsequent decarburization of scrap steel was mixed with 2-micron graphite powder, pressed at 50,000, 100,000, and 200,000 psi, and sintered in hydrogen at 1200°C for the periods of time ranging from 15 to 120 minutes. In the second section of the investigation, electrolytic iron powder was mixed with graphite of an average particle diameter of 2, 4, 6, and i6 microns, pressed at 100,000 psi, and sintered at temperatures ranging from 1000° to 1200°C. for periods of time of 30 to 180 minutes. By following this procedure an indication of the effect of the following variables upon the density and tensile properties of iron-carbon powder compacts was obtained: (I) forming pressure, (2) sintering time, (3) particle size of graphite powder, (4) sintering temperature, (4) type of iron powder.

Jan 1, 1947

By G. L. Kehl, Emilo Jaraiz F., J. S. Brett

The transformation of eutectoid beryllium bronze has been quantitatively investigated at 550° and 592°C, the temperature region where the products of p decomposition are a fine lamellar eutectoid and a coarse lamellar aggregate which replaces the fine eutectoid with prolonged annealing. Metallographic evidence indicates that the coarse lamellar aggregate forms preferentially in the most densely lamellated regions of the fine eutectoid and favors the hypothesis that the development of the coarse lamellar aggregate in the fine eutectoid is due to the occurence of a cellular segregation reaction. WHEN eutectoid beryllium bronze (Cu-94 pct, Be-6 pct) is isothermally transformed at high temperatures in the and y region after quenching from the fl field, the principal initial decomposition process is G one of growth of approximately spherical nodules composed of a number of lamellar colonies of the a and y phases. After the initial reaction has proceeded substantially or completely, depending on the transformation temperature, a second reaction occurs wherein the fine lamellar eutectoid is replaced by a coarser lamellar aggregate composed of the same oand yphases.' This reaction is not simply a spheroidization of the initial fine eutectoid but the nucleation and growth of a coarser, structurally different, and more stable distribution of the @and yphases. Fig. 1 illustrates the replacement of the initial fine lamellar structure by a coarse lamellar aggregate. The a phase is the dark mottled constituent; the light constituent the y phase. The phase diagram for the copper-rich end of the Cu-Be system2 is shown in Fig. 2. The a phase has the face-centered cubic structure characteristic of copper-rich solid solutions. The B phase is a disordered body-centered cubic structure, while the y phase is body-centered cubic, ordered (CsC1, B2 type). A. viswanathanS investigating Debye patterns of Cu-6 pct Be discovered that a transitory phase appeared on very rapid quenching from the /3 region which was absent when the quenching velocity was moderate. The phase could be assigned a body-centtred cubic structure with a lattice parameter of 2.876. Tempering at 100°C for 2 hr after quenching resulted in complete disappearance of the phase. The work of Fillnow and Mack' is the only previously published study of the isothermal transformation of eutectoid beryllium bronze. Their study elucidated the nature of decomposition at various subcritical temperatures in an exploratory fashion. The purpose of the research reported in this paper was principally to obtain quantitative information on the isothermal decomposition of the fl phase and to clarify the relationships existing between the fine lamellar eutectoid and the coarse lamellar aggregate. EXPERIMENTAL PROCEDURE The material used in this investigation was an almost eutectoid Cu-Be alloy bar furnished by D.J. Mack. The alloy had been melted under a protective carbon cover and centrigugally cast into a graphite mold preheated to 490 "C. Segregation was minimized by violent agitation during melting and pouring. The analysis of the casting was 93.85 pct Cu, 5.60 pet Be with traces of Si, Mg, Mn, Co, and Al. To determine the minimum soaking time necessary to insure specimen homogeneity, a number of specimens were held in the P region at 788OC for times fron 1 min to 12 hr and isothermally transformed at 550°C. Specimens betatized less than 12 min exhibited partial transformation at times shorter

Jan 1, 1961

By R. G. Schaal

The Magma Mine at Superior, Arizona had an unimpressive beginning as a. worked out silver mine that was purchased in 1910 for $130,000 and then incorporated into the Magma Copper Company which has been continuously mining the deposit since 1915. Copper is the principal metal produced. However, zinc, gold, silver and iron have also contributed to the total metal product. Prior to 1973, the production rate of 1500 tons per day was maintained by hoisting 4 and 5 ton pay-loads at speeds up to 1100 FPM through four small hoisting shafts. The hoists used included 8' and 7' diameter double drum, double clutched doc. and a.c. motor driven geared units built as early as 1917. One old timer that did yoeman's service for many years was an 8' Bollen Pulley with a.c. geared drive that utilized an endless rope system with mechanical grip and release mechanism built into the pulley's throat. Primary power for all of these old production hoists was 25 Hertz. Exploration that was completed in 1967 developed a reserve of 10 Million tons of 5 per cent copper which was sufficient to justify new capital expenditures for enlargement of productive facilities to 3300 tons per day. To reach the new reserves a 22' I.D. concrete lined vertical shaft was sunk to an initial depth of 48431. A 12 ½ diameter adit was bored from the mill side of the mountain to intercept the shaft at a point about 1100' below the collar. This 9200' long adit provides the right-of-way for the mine to mill railway and egress for heavy supplies from rail head as well as a conduit for potable water, electric power, compressed air and mine drainage. Mine operating levels begin 3582' below collar and thereafter have been cut at 100' vertical intervals. Skip loading stations have been installed 4282' and 46821 below collar with an in-shaft skip dump station located 800' below collar. This provides for 4500 tons of storage above the mine to mill train loading station located 1100' below collar. Ore and waste are moved horizontally from stope chutes and drift headings by rail haulage to transfer raises which channel all material to the two mentioned skip loading stations. The 22' diameter shaft crossection is arranged with the two skip compartments on the south side separated from the manway and utility compartments by the cage compartment. The cage counterweight operates in a portion of the southwest quadrant of the shaft. The hoisting plant consists of two conventional Nordberg double drum, single clutch, geared, d.c. motor driven units that are identical except for the drives and automatic controls. The drums are 15' diameter x 105" face with LeBus grooving for 2-1/8" diameter wire rope wound in three layers. Mechanical design emp1o::ed is the same as has been used for the past twenty- five years. One drum is attached to the main shaft by 2 large bolted integral shaft flenge. The loose drum is engaged by a 4-arm positive tooth clutch meshing with radially cut teeth of the clutch ring which is bolted to the drum. The drums are one-piece steel plate weldments having a finished weight of 60 tons each and are mounted upon a 36" diameter shaft that also weighs 60 tons. With the addition of brake rings, clutch, bull gear and rope, the total dead weight adds up to nearly 250 tons that is supported by just three double row spherical roller pillow block bearings. There is no bearing between the drums. All pinion shafts as veil as all head sheave journals are supported in the same type of antifriction bearings.

Jan 1, 1975

By A. M. Adair

The effect of cathodically charging zone-refined iron with hydrogen and the resultant yield stress-grain size relationship has been investigated by tensile testing at -31°C. The resulting Petch plots (using a least-squares analysis) reveal a significant reduction in the slope and an increase in the intercept for specimens cathodically charged with hydrogen, regardless of whether the hydrogen is present during testing or is removed by evacuation. Other than surface blistering, the major effect of cathodically charging this material is to create occasional grain boundary cracks and thus presumably a large number of free dislocations at grain boundaries. These results are consistent with the hypothesis that the slope of the Petch plot is related to the stress required to activate dislocation sources at or near pain boundaries. While there is no significant effect of the presence of hydrogen on the lower yield stress of this material, the ductility is considerably reduced. After hydrogen removal by evacuation, the ductility recovers substantially and almost complete recovery of ductility is experienced by the smaller grain size specimens. THE influence of hydrogen on the mechanical properties of ferritic materials has received much attention throughout the history of the metallurgy profession. This interest has stemmed from the obvious importance of preventing the catastrophic failure of parts in service, and from the desire to determine what mechanism is responsible for the observed behavior. The various mechanisms proposed for hydrogen em-brittlement have been discussed in detail by Tetel-man,'who concludes that a combination of the applied stress and hydrogen pressure within voids best accounts for the many experimental observations reported. From a quite reasonable correlation of the strain aging and delayed-failure behavior of a variety of materials,2-7 Troiano and coworkers are of the opinion that the delayed-failure mechanism (slow strain rate embrittlement as well) is better explained as a lattice effect; solute elements diffuse to regions of high triaxial stress, form uncondensed atmospheres there, and effect a reduction in the cohesive strength of the lattice. Since hydrogen yield points8,9 have been observed in ferritic materials, and since the hydrogen embrittlement process may be related to strain aging, one further contribution to embrittlement could be hydrogen-dislocation interactions which make crack blunting by plastic deformation a more difficult process. The etch" relationship offers a means of comparing the relative ease of initiating and propagating plastic deformation in metals and alloys. In the present study, this relationship was used to compare the behavior of zone-refined iron in three conditions: uncharged, cathodically charged with hydrogen, and cathodically charged with hydrogen and evacuated. These Petch plots and the observed ductility parameters allowed a separation of the effects of the very presence of hydrogen and the act of cathodically charging hydrogen into this material. MATERIALS AND EXPERIMENTAL PROCEDURE An ingot of zone-refined iron was obtained from Battelle Memorial Institute which contained the following (typical) interstitial impurities in ppm: carbon, 10 * 5; nitrogen, 1; oxygen, 22; hydrogen, 0.9. The ingot was cold-reduced to a 1/2-in.-sq cross section, recrystallized 1 hr at 575°C, and then straight-rolled to a thickness of about 0.105 in. Tensile specimens were milled from the strip having a 1-in. gage length

Jan 1, 1967

By Gregoire Gutzeit

THE development reported in this paper was begun by the author a number of years ago, while he was a lecturer on complex chemistry and metallurgy at the University of Geneva, Switzerland, and in charge of that institution's research laboratory. Completion of the development and reduction to practice did not occur until last year at the Westport mill, laboratories and testing plant of the Dorr Company, where this method is now in general use for identifying and localizing the mineral constituents of both metallic and nonmetallic ores. It has proved to be a practical tool of the metallurgical staff at the Westport mill, devising unusual milling flowsheets for complex and refractory ore bodies. In a number of instances the findings have been successfully used as fundamental factors in the design and specification of complete metallurgical plants. Seven examples of the use of this method in solving practical milling problems are included in this paper. GENERAL OUTLINE The microscopic study of an ore, at first only of scientific interest, has proved extremely useful both in practical geology and in ore dressing. The binocular magnifying lenses for rough observation of the products of an ore-dressing plant have been in use for a long time; but only within the last few years has a systematic microscopical examination of ore samples become a normal tool of any research laboratory dealing with ore-dressing problems. Such an investigation avoids considerable loss of time as well as empirical trials and useless experimentation. It will generally indicate the correct grinding and often will suggest the proper method of treatment. The petrographic determination of transparent minerals in thin sections, or even in grains, has been perfected, and very accurate methods have been devised to meet any requirement, such as Feodorof's rotating stage on the petrographic microscope. Almost all transparent minerals can be positively identified by their optical properties; i.e., isotropism, anisotropism, color, pleochroism, refractory index, cleavage, crystal form, birefringence, and others. The identification of opaque minerals is a much more difficult problem and can be done only by using polished specimens. Unfortunately, most of the valuable metallic ores, and even some of the nonmetallic ones, are not transparent; therefore it has been necessary to develop a special technique for the determination of these minerals. Some optical properties-for instance, isotropism, anisotropism, color, cleavage, reflecting power-are often adequate in roughly classifying the mineral. Only "reflecting power" is a measurable value, provided special photometric equipment (ocular photometer or Orcel's photoelectric cell) is available. The other optical properties mentioned are more or less relative,

Jan 1, 1942

By C. C. McDermond, Others, B. N. Zavoico

Production of crude oil in Venezuela for the year 1937 was 186,653,-916 bbl., as compared with 155,228,982 bbl. produced in 1936, an increase of almost 31,500,000 bbl. The oil-field strike, which started on Dec. 14, 1936, lasted until Jan. 25, 1937, when a total of 10,000,000 bbl. of production was estimated to have been lost (5,750,000 bbl. in 1936 and the remainder in 1937). Of the total of 186,653,916 bbl. produced in 1937, the Lagunillas field contributed 45.6 per cent, a drop of approximately 10 per cent under 1936 figures; Tia Juana, 14.3 per cent; Quiriquire field, 14.0 per cent; La Rosa area, 13.3 per cent and the Mene Grande field, 7.6 per cent, these being the five leading contributors of the year's production. Detailed production figures by fields and by companies are shown on Table 1. Of the total production of Venezuela the following four major companies accounted for the greater proportion: Standard of Venezuela and Lago Petroleum Corporation together, 48.3 per cent; Shell, 37.4 per cent and Venezuela Gulf, 14.0 per cent. At the end of the year, 2491 wells were producing, of which number 1291 wells were pumpers, or about 52 per cent. Production The accompanying statistics of production record of Venezuela oil fields from its inception to Dec. 31, 1937, shown on Table 2, indicates that the cumulative production reached 1,503,283,228 bbl. In order of importance, Lagunillas leads all the fields, having accounted for about 50 per cent of Venezuelan production, followed by La Rosa area, which produced about 21 per cent; Mene Grande, which produced about 13 per cent, and Quiriquire, which produced 6.5 per cent. Table 3 shows the age of each field. Mene Grande is the oldest, having produced for 24 years; Tarra is next, 21 1/2 years old, and El Mene third, 171/2 years. The gravity of the crude from the various fields, also shown on Table 3, remained unchanged, the only addition being the new Tia Juana field, which averages 15.6' A.P.I. Table 4 shows the method of production by fields as of Jan. 1, 1938; at the end of the year 2491 wells were producing, compared with 2005 wells producing at the beginning of 1937, or an increase of 486 wells. The completions for the year reached 512. Of the 2491 wells producing crude oil, 1291 wells, or approximately 52 per cent, were pumping, 925 (approximately 37 per cent) were flowing naturally and 275 (11 per cent) were on

Jan 1, 1938

By J. F. Havard

Gypsum is a useful industrial mineral found abundantly on the earth's crust. It is inexpensive to mine and process, and its calcined products have a wide range of readily controllable properties such as strength, density and setting time. It has proven to be such a useful material indeed, that ten American companies, operating some 57 calcining plants in 25 states in 1958, produced or imported in that year a total of 13,649,000 tons of the crude mineral valued at $39,361,000, which they then converted into manufactured products with a value of $329,070,000. Gypsum (CaSO4.2H2O) is calcium sulfate with two molecules of combined water, which are responsible for most of its useful properties. It is closely associated in most deposits with anhydrite (CaSO4), which contains no combined water and has limited commercial value in the United States. Man has long recognized the useful qualities of gypsum. It was utilized by the Egyptians in the construction of the pyramids and, later, by the Romans for important structures. Many of the ancient peoples prized gypsum for artistic and ornamental purposes, carving statuary from alabaster and making casts with plaster. The tabular variety, selenite, was used for windows, and the light transmitted through these windows reminded people of light from the moon (selene), hence the name selenite. The use of gypsum continued through the Middle Ages and into modem times. Benjamin Franklin was a famed exponent of gypsum because he applied ground gypsum to clover fields in the form of large letters which later read, in the more luxuriant growth, "land plaster used here." Gypsum is still used as an effective conditioner for some soils, but in recent decades, particularly in North America and Europe, it has become much more important as a major material for the building industry. Description Gypsum and anhydrite are closely associated minerals. Gypsum is found in a number of forms: massive rock gypsum, alabaster, selenite, satin spar, and gypsite. Anhydrite is found as massive rock or as smaller bodies or isolated crystals included in gypsum. Massive Rock Gypsum comprises most of the commercial gypsum and occurs as a sedimentary rock, interbedded in most places with shale, limestone or dolomite. This rock is soft and crystalline. Its color is white or shades of gray, pink, yellow, brown or other colors. Alabaster is a pure, compact and fine-grained variety suitable for use in sculpture or turning into artistic forms; it may be white or selected for attractive coloration. Selenite is gypsum crystallized in flat, transparent, flexible foliated plates, found in clays or in surface vugs in gypsum. Satin Spar is a fine silky fibrous variety with the axes of the crystalline fibers perpendicular to the vein or joint in which it has formed. Gypsite is an earthy mixture of gypsum with clay and sand in secondary formations; it is sometimes useful as a soil conditioner and has been used in making base-coat plasters. Pure gypsum contains 20.9 pct combined water, 46.6 pct sulfur trioxide (SO3) and 32.5 pct lime (CaO). Standard specifications (American Society for Testing Materials Designation C 22-50) read that minimum purity for material to be called gypsum is 70 pct CaSO4.2H20. Most of the commercial gypsum is 85 to 95 pct pure as produced. Impurities in

Jan 1, 1960

By Frederick Mark Becket

DOCTOR Albert Sauveur, distinguished scientist and Honorary Member of this Institute, predicted in the first Howe Memorial Lecture that the privilege of delivering this annual address would be considered a highly significant honor. The intervening years have well borne out Sauveur's prophecy. I wish to assure the American Institute of Mining and Metallurgical Engineers that I also deeply appreciate this honor, recognizing at the same time the present and even more the future responsibilities with which it is accompanied. Several of the previous lecturers had the good fortune to attend the classes of Professor Howe and to work in his laboratories. I was similarly favored, although in my instance and to my great regret the period was all too short. However, Howe's book, published in 1903, "Iron, Steel and Other Alloys," afforded me abundant opportunity to continue these studies. How well I remember the inspiration I derived from this famous book by Howe, the metallurgical master, pioneer, and educator! Remembering that Professor Howe contributed numerous papers to The Metallographist, a magazine supported from a technical point of view by the world's pioneers in metallography, I was curious a few days ago to learn the nature of Howe's early contributions to this magazine. The first paper by Howe in the first year of The Metallographist (1898) dealt with the allotropic theory; the second also treated of allotropy, and I quote the first sentence of that paper: The allotropic theory of the hardening of steel may, like so many other important theories, have to be accepted or rejected not on direct proof or disproof, but on the accumulation of circumstantial evidence for or against it. Howe's ability to stimulate others by his deep understanding and clarity of expression was truly remarkable; but just as striking was his intuitive judgment concerning the implications of metallurgical data in the arts and sciences. It therefore seems fitting that this lecture comprise a broad treatment of the subject chosen, rather than a closely documented thesis on any one phase of the problem; that in it attention be focused

Jan 1, 1938

By C. F. Smart

Since their comparatively recent development, the alloys of cadmium with silver and copper or nickel, and of cadmium with nickel alone, have been used somewhat extensively as liners for connecting rod bearings and main bearings of internal-combustion engines. In applications where, owing to high bearing loads and elevated operating temperatures, the life of bearings made from tin-base or lead-base alloys has been undesirably short, cadmium alloys have demonstrated considerable advantage. In applications where, because of deflection of the crankshaft or bearing supports, copper-lead bearing metals have resulted in scored shafts, cadmium alloys have been operated successfully. The somewhat serious drawback to these alloys in bearing service has been that they, in common with copper-lead and certain lead alloys, are susceptible to corrosion in the presence of lubricants containing organic acids. These acids may be fatty acids (such as oleic acid) derived from animal or vegetable oils that sometimes have been compounded with engine lubricants, or they may be compounds of an acid nature developed by the oxidation of some petroleum oils under operating conditions. The result of such acid attack on bearings is illustrated by the photograph, Fig. 1. The petroleum oils that are most readily oxidized to a corrosive condition, and the operating conditions under which such oxidation most readily occurs, are now rather well known among the technical organizations of both the petroleum and automotive industries. While means have been developed for inhibiting petroleum oils against such acid formation, the knowledge that this condition may be encountered has been a factor in restricting the wider use of cadmium alloys as engine bearings. It has appeared, therefore, that their value and use would be enhanced if they could be made corrosion-resistant to a degree compatible with the most severe operating requirements. Investigation, undertaken with this in view, indicated that the addition of fractional percentages of the metal indium to the cadmium bearing

Jan 1, 1938

By C. L. Mantell

ALTHOUGH SO common and well known a metal, tin is really a less abundant element than many of those less familiar and usually ranked with the scarce or rare elements, such as cerium, yttrium, lithium, beryllium., titanium, zirconium and vanadium. The color of tin is white, with a slightly bluish tinge. When it is compared with nickel, the latter metal is brown. When placed alongside of tin, chromium is definitely blue. Tin is whiter than silver or zinc. Exceedingly thin films of tin show various shades of brown by transmitted light. The metal has a brilliant luster, and when mirror-polished, has high light reflectivity. The luster depends to a large extent upon the pouring temperature at which the metal is cast. If the temperature be, too high, iridescent colors may show on the surface. These are the result of oxide film formation. If the pouring temperature be too low, the surface is dull. Small amounts of foreign metals, such as lead, arsenic, antimony and iron, decrease the luster of tin and impart a yellowish tinge to the metal. The structure is decidedly crystalline. The cast metal is a mass of crystals. When a bar of tin is bent, it emits a characteristic creaking sound. This is called the "cry" of tin, resulting from the grinding of the crystals one against the other during the bending of the metal. Tin metal may lose its crystalline structure by cold working, but grain growth occurs rapidly under the influence of heat. Metal which has been cast at a low temperature may become amorphous as the result of mechanical work. If such material be heated to temperatures well. below the melting point, say at 110° C. for a half hour or for a few minutes at 150° C. recrystallization occurs. If the surface of tinned plate, tin foil, or tin metal in cast form be etched with hydrochloric acid containing a little free chlorine, attack occurs at the intercrystalline faces. The surface shows patterns resembling the frost flowers on window panes in winter. The etched appearance is called moiré metallique. Fine dendritic surface crystals of tin may be obtained by casting the metal on a surface of polished steel. In commercial tin plate, the intercrystalline boundaries are shown by fine grooves or channels, which result from the method

Jan 1, 1929

By A. Boltax

H. Herman and M. E. Fine (Northzcesteriz University)—The author is to be complimented on the quality and completeness of his work. Of special interest to us was the exponent of time in the exponential rate equation, n = 0.28 ± 0.03, since it is consistent with results for the early stage of quench-aging in A1-2 at. pct Cu, n = 1/3, first determined in this laboratory."' In that work we attributed the early kinetics to attraction of vacancy - solute atom complexes to the plate-shaped zone due to the strain field about the zone and the lowering in free energy. To our knowledge, Hirano et 1.' were the first to

Jan 1, 1962

Jan 1, 1917

By Zay Jeffries

Jan 1, 1930

By L. L. McDaniel

DURING the past few years a number of improvements in smelting and power equipment have been made at the Douglas smelter of the FIG. 1.-GENERAL PLAN OF SMELTER. Phelps Dodge Corporation at Douglas, Ariz. In the summer of 1935 work was started on the first unit of a new reverberatory waste-heat boiler plant which ultimately was to furnish steam for a modern high-pressure power plant. A second reverberatory waste-heat boiler unit

Jan 1, 1939

By Donald W. Gentry

Many firms in the minerals industry are facing enormous capital-equipment requirements for existing operations, planned expansion programs, pollution control systems, etc. Yet, because of existing economic conditions, mining companies find it increasingly difficult to obtain reasonable financing for the acquisition of large, high-cost capital equipment. One way of obtaining the use of mining and other major pieces of high-cost capital equipment is through leasing. The popularity of this approach is evidenced by the growing number of leasing companies, equipment manufacturers, and financial institutions now offering this service to their customers. Indeed, leasing has become a billion-dollar industry, and many commercial banks have developed sizeable portfolios in this area. "Should we buy or lease?" This question eventually comes up whenever a mining company needs additional major capital assets. Unfortunately, many buy-or-lease decisions are made on an emotional basis-rather than on a proper financial evaluation that would yield the…

Jan 9, 1975

NEW MEMBERS The following list comprises the names of those persons who became members during the period Sept. 10 to Oct. 10, 1915: Members BENEDICT, C. HARRY, Met Calumet & Hecla Mining Co., Calumet, Mich. BETTERTON, JESSE OATMAN,. Met., Supt. Blast Furnaces and Sulphate Depts., St. Louis Smelt. & Ref. Co., Collinsville; Ill. CLARK, H. A., Supt Calumet & Arizona Mining Co., Douglas, Ariz. COOPER, CLAUDE H.; Asst,. Supt Calumet & Hecla Smelt. Works, Hubbell, Mich. CRAMPTON, FRANK A., Min. Engr.; Mine Supt., Platinum Gold Min. Co., Goodsprings, Nev. CUNNINGHAM, GEORGE HAMILTON, Asst. Supt. of Construction, Anaconda Copper Mining Co., Anaconda, Mont.

Jan 11, 1915