Search Documents

By B. K. Larkin, H. K. van Poollen, H. C. Bixel

A detailed treatment is given of the transient pressure behavior of a well located near a linear discontinuity. On either side of the discontinuity, the values of permeability, viscosity, compressibility, and porosity are uniform, but may be different from those on the other side of the discontinuity. These results generalize previously published works which assumed the permeability ratio for media on different sides of the discontinuity was zero, one, or infinity. One application of this material would be to facilitate detection of facies changes or fluid-fluid contacts by transient testing. Solutions, presented graphically, show pressure decline for constant rate fluid production. The range of variables examined includes dimensionless time from 0.1 to 100, rnohility ratio from 0.001 to 1000 and specific compressibility ratio from 0.001 to 1000. For dimensionless tinze less than 0.4, the pressure behavior is essentially that of a well in an infinite reservoir. Thus, reservoir properties near the well may be estimated in the usual manner. Using an overlay technique to match an experimental curve with one of the theoretical curves, it is possible to estimate the distance to a discontinuity by substituting the actual time t and the corresponding dimensionless time , at which a match occurs into the equation where is the diffusivity near the well, and may be estimated from data taken at early time. Because of both the complexity of the solutions and limited computer facilities, well interference problems were not examined extensively. However, it was found that well interference may be masked by the discontinuity in some cases. By superposition of the results of constant rate fluid production, the problenz of pressure buildup may be treated. Such results show that for early shut-in times correct values for the transnzissibility are obtained from conventional semilog plotting. However, erroneous values of the static reservoir pressure are obtained unless data at large shut-in times are taken. INTRODUCTION Transient well testing has yielded estimates of such reservoir parameters as static reservoir pressure, permeability. porosity, and well bore effects. In most tests, it was assumed that the reservoirs were homogeneous and iso-tropic. Anisotropic media' and radial discontinuities were considered.'.' Various studies have been made on multiple-layer reservoirs." ' Linear discontinuities have been described for problems of one-dimensional flow.' In the present paper, a mathematical treatment is given for a well located near a linear discontinuity in an otherwise infinite medium (see Fig. 1). An actual reservoir analogy would be a well in a relatively thin reservoir near a fluid-fluid contact, or a well located in a reservoir exhibiting a sudden change in rock and formation characteristics, such as thickness, porosity, or permeability. A sudden change in porosity or permeability may be caused by clay fill or other types of facies changes. Sudden thickness changes niay be the result of such geological formations as buried shore lines and channel deposits. In otherwise uniform formations, a linear discontinuity may be caused by fluid-fluid interfaces such as oil-water contacts. 3s-oil contacts, or gas-water contacts.

By O. D. Gonzalez

ThIS communication presents the results of a determination of the permeabilities of hydrogen and deuterium in a iron from 360° to 560°C. Recently Heu-mann and primas' have given values of the diffusivity and solubility in a iron of the two isotopes from which the permeability can be calculated. The work reported in the present communication, however, is a direct measurement of the rate of permeation of the isotopes through an identical iron specimen under the same conditions, so that systematic errors can be minimized in the calculation of the ratio of the permeabilities—the value which is usually of main importance in establishing limits for isotopic differences in diffusive processes. Experimentally the procedure used was the usual one: a steady-state flow of gas produced by a pressure difference across an iron membrane was observed as the pressure rise with time in a previously evacuated, calibrated volume connected to the outlet side of the membrane, while a constant pressure of gas was maintained on the opposite inlet side. The membrane was a cylindrical tube 9.38 cm long, 0.730 cm inside diam, 0.187 cm wall thickness, fabricated of 99.95 pct vacuum-melted National Research Corp. iron (less than 0.003 pct C). One end was sealed by a heliarc-welded iron (99.95 pctj lid of 0.147 cm thickness; the other end of the tube was welded to a 304 stainless-steel tube (0.318 cm ID and 0.318 cm wall) which connects to a vacuum system and to the calibrated volume including a dibutylphthalate manometer. The temperature of the iron membrane was maintained constant to ±0.l°C and was measured with an iron-constantan thermocouple which was calibrated against a standard Pt/Pt-Rh thermocouple: the temperature variation along the length of the membrane did not exceed ±0.5°C. Hydrogen was allowed to pass through the membrane assembly for 72 hr at 615°C before permeability measurements were begun. The system was tested at temperature before and after the experiments by a substitution of helium for hydrogen in the inlet side; under these conditions the pressure rise observed in the outlet side was negligible at all times. The gases used for the permeability measurements were 99.95 pct Matheson prepurified H2 and 99.7 pct D2 (0.3 pct HD) from the Isomet Corp. The gases were dried with liquid N2 before use. In Fig. 1 the logarithms of observed flows, jt, for a pressure difference of 73.4 cm Hg are plotted against T-1 Each point in Fig. 1 represents the slope determined by a least-square evaluation of a plot of the pressure in the outlet side of the membrane against time, including at least two separate sets of observations. Each point in the figure has an uncertainty of ±0.6 pct arising from the experimental uncertainty in the pressure and time measurements. The standard deviation of the observed pressures from the straight lines in all cases is less than the experimental precision of the measurements. The observed flow, jt, includes a small but not negligible flow through the stainless-steel connection.

Jan 1, 1968

By Michael Hoch, Seong Kwan Rhee

The ternary system Zr-Cr-0 was investigated at 1200°, 1500°, and 1700°C. The isotherms at these temperatures were determined by metallographic and X-ray diffraction analysis of carefully selected alloys. AS a part of a series of investigations1-4 of the ternary and quaternary phase diagrams on refractory metals and their compounds, the ternary system Zr-Cr-O was investigated at 1200°, 1500°, and 1'700°C. The binary diagrams Zr-Cr, Zr-O, and Cr-0 as reported by Hansen5 and Levin et a1.' and the existence of a ternary coompound ZrsCrsO (q-carbide structure a. = 11.96A) provided a good base for this investigation of the Zr-Cr-O phase diagram. MATERIALS The materials used and their suppliers were: Zirconium powder, 99.4 pct pure, Charles Hardy, New York; Zirconium dioxide, Fairmount Chemical Co., Newark, N.J.; Chromium powder, 99.85 pct pure, Fairmount Chemical Co., Newark, N.J.; Chromium sesquioxide, 99.86 pct pure, J. T. Baker Chemical Co., Pillipsburg, N.J. Though the materials used were not "hyperpure", the impurities present do not affect the results (lattice parameters, phase boundaries) within the experimental accuracy. EQUIPMENT AND PROCEDURE The detailed procedures and equipment used for this investigation were similar to those described elsewherel' "ith the exception that in this study an induction-heated argon-atmosphere furnace was used. The latter furnace was used to prevent the vaporization of chromium metal in samples in the higher temperature range (above 1200°C). The tungsten crucible was induct ion-heated in a vertical quartz tube filled with argon gas. The quartz tube was 1-1/2 in. in diameter and 10 in. long; it was connected at the top and bottom to water-cooled copper plates. The argon gas of a purity 99.995 pct was further purified by being passed through zirconium metal chips which were maintained at 800°C in a silica tube 1 in. in diameter and 30 in. in length. The furnace was flushed with argon gas for an hour before starting heating; during heating, a slight (3 cm oil) overpressure of argon was maintained in the system. Power was supplied by a 20-kw Ther-Monic Induction Generator. The samples rested on a tungsten-wire basket; the wire basket was connected to a tungsten wire which passed through the tungsten crucible lid, and entered the system on top through a Wilson-type seal. By pulling on the wire, the sample was removed from the crucible and dropped to the water-cooled copper base of the furnace. Because of the presence of argon gas, the cooling of the sample was even more rapid than in the vacuum furnace.' EXPERIMENTAL RESULTS AND DISCUSSION 1) Isothermal Section at 1200°C. The compositions investigated have been numbered within the phase diagram, Fig. 1, and all the pertinent information about the samples can be found in Table I. This table lists the composition of the samples, the phases present in the room-temperature diffraction patterns, the phases detectable in the microstruc-ture, and calculated lattice parameters of the a-zirconium phase. The shapes of the various phase

Jan 1, 1964

By D. D. Pollock, D. I. Finch

PREVIOUS work' on a four-component system (Cu-Mn-Ni-Fe) resulted in the development of consistent relationships between the chemical composition and the electrical properties of these manganin-type alloys. The present study was undertaken to develop alloys with temperature coefficients of resistivity and thermoelectric properties more desirable than those of the manganin type, and to determine whether the relationships which had been found for the Cu-Mn-Ni-Fe alloys could be extended to five-and six-component alloy systems. PREPARATION OF ALLOYS The five- and six-component alloys were made from OFHC copper rod, ARMCO iron, electrolytic nickel, manganese cathode chip, and special high-purity aluminum and indium. A Cu-Mg master was used for deoxidation. The compositions of these materials are given in Table I. The alloys were melted and cast as indicated previously,' except that no cover was used and the melts were teemed. EXPERIMENTAL PROCEDURE The finished wire size of 0.0808 in. diam was again selected for the reason that the test specimens would be self-supporting, thus eliminating any extraneous effects which might have been introduced by winding smaller diameter wire on spools or forms. The following tests were performed on the finished wires: A) Chemical Analyses—All of the components of these alloys were determined by premium gravimetric methods. The principle residual impurity contained in these alloys is 0.008 pct Mg (by weight), maximum. Tables II and 111 present the mean analyses computed from at least four determinations of each constituent. B) Electrical Characteristics—The test procedures forthe determination of the thermal emf vs copper, resistivity, and the resistance-temperature relationship are given in detail in Ref. 1. It was also shown that the resistance-temperature relationship is of the form Pt = P,n + At -B/2, [1] where P, is the resistance at t C expressed in percent of a given standard resistance, P, is this per- 0 centage at 0°C, and A and B are constants for a given, properly treated, composition. The results of the electrical tests are also given in Tables II and 111. INTERPRETATION OF DATA The modified Linde2 formula, known to be valid for dilute binary solid solutions, was applied to the complex Cu-Mn-Ni-Fe type alloys. This relationship is of the form where Ap is the increase in resistivity. Zb the valence of the solute, Zn the valence of the solvent, and K and K are designations assigned by Robinson and Dorn3 to the constants for the periodic group to which solute element belongs. The units of K, are -cm per valence difference squared per at. pct; those of K2 are pa-cm per at. pct. For the sake of brevity, these units are not repeated in the following discussion. Calculations were made to determine if this formula was accurate for five-component systems. No experimental studies were made of the Cu-In and Cu-A1 binary systems. The effects of indium additions upon the resistivity of copper are given by Linde. These data, along with those of the effects of Mn and Fe, permitted the calculation of the effects of Al.

Jan 1, 1959

By W. C. Knoblaugh

ROTARY kilns are adaptable to many fuels, but this paper deals principally with the use of powdered coal. The observations and conclusions presented are based on rotary kilns used in the manufacture of basic refractories for steel furnaces. Solid fuels are pulverized for two principal reasons: (I) ease of control, and (2) rapidity of combustion. By the use of pulverized coal, the operator can increase or decrease the fuel supply by small increments and with very little time lag between the change of control and the resultant change in the flame. This is extremely important in this type of furnace, as the temperature range for maturing the clinker is very narrow. By fine grinding, it is possible to increase the rate of burning of the coal, thereby liberating great quantities of heat within a small space in a short time. Under given conditions, temperature is a measure of the heat liberated per unit of time. To attain the temperatures of 2950° to 3150°F., which are encountered in the manufacture of various steel-furnace refractories, it is estimated that it is necessary to liberate 125,000 to I75,000 B.t.u. per cubic foot of the burning zone per hour. The manufacture of dolomitic refractories is a ceramic process and, as is true in most such processes, the material must be subjected to a certain critical temperature for a certain length of time in order to complete the reaction. If the time of reaction is reduced, the temperature must be increased; in other words, if the rate at which the material flows through the hot zone of the kiln is increased, the temperature of the hot zone must be increased to compensate for this shorter exposure to the flame. FIRING WITH PULVERIZED COAL Fig. I is a line drawing of a rotary kiln with the attendant equipment indicated in their relative positions. The kiln proper consists of a sloping, refractory-lined steel tube rotating slowly about its longitudinal axis (0.75 r.p.m.), and is countercurrent in operation in that the raw feed is introduced at the stack end and gradually approaches the zone of highest temperature at the lower end, where the fuel is introduced. Before 1930, the usual method of firing a rotary kiln was to store the coal in the pulverized form and then feed from this storage to the kiln as needed. This proved unsatisfactory and dangerous because of dust explosions and the inability to obtain an even feed to the kiln caused by arching of the coal in storage and flooding of the coal feeders. In later years the practice has been to store the raw coal and grind it as it is needed. Such a layout is indicated in Fig. I. The coal is stored in bins, charged from the top and drawn from the bottom into recording scales and then into some type of unit pulverizer. There are a number of good pulverizers on the market, each incorporating features that the manufacturer considers outstanding.

Jan 1, 1946

THE paper on "Cross-cuts in Coal Mining," by J. J. Rutledge (published in MINING AND METAL-LURGY, February, 1927, p. 64) was brought up for discussion at the annual meeting, where the follow-ing comments were made T. D. Thomas (Lehigh Coal & Navigation Co., Lansford, Pa.) : This question has caused me a lot of worry, not in the particular district in which I am, but throughout other districts. There are always several angles to consider. If you are in a hurry to push development work, you might increase the distance between cross-cuts from 60 to 350 ft., but if you have a 40-ft. chain pillar every 60 ft. it will cut down your entry driving a whole lot. Looking at it from the ventilation angle, I agree that too many cross-cuts in entries are bad things. You have a tremendous amount of leakage, and I have seen currents starting out with 45,000 cu. ft., and after passing about 30 or 40 cross-cuts the current has dwindled down to about 18,000 or 15;000 cu. ft. The result is that the question of putting in auxiliary fans is raised. That involves several points into which I do not want to go too far, but I am in favor of not getting in too many cross-cuts, putting them in only where they are necessary: I think the state mining laws are wrong in a number of places on that, and that when you finish with a cross-cut it should be in the room. It should be well sealed on an entry. There are several ways of tightening up the cross-cuts so as not to have the great amount of leakage and wastage of: air that we now have. 'I prefer tile stopping; other people prefer cement or brick, but there is a big fac-tor to all mines, saving the mine. I checked up on the number of fans in the anthracite region and found there are 651. That was derived from the state report of 1921, and it enabled me to compute from the power the weight of the air. In the anthracite region of Pennsylvania we put in 9 tons of air to every ton of coal we get out. Tracing that back again and taking the Government's figures which they made some time ago, I found but 20 per cent of the air got to the faces where it was actually needed. That is a tremendous big loss and shows a possibility for saving, money for the various coal companies. Chairman Rice: I think what Mr. Thomas refers to was an investigation by R. Y. Williams, of the Bureau of Mines in Illinois, where a study was made of 100 typical mines, and, speaking off-hand, my recollection is that we found as little as 15 per cent of air reached the faces in one of the mines and another was as much as 50. That seems to be a reflection on the type of stoppings and general ventilation scheme.

Jan 3, 1927

By C. E. Sims

In some experimental work conducted several years ago, it was noted that sulphur seemed to have a distinct influence on grain size of carbon steels. 111 order to check this observation, a series of S..A.E. 1040 steels was made with the normal composition held as nearly constant as possible. The steels were made with three sulphur levels, which were 0.012, 0.024 and 0.038 per cent sulphur, respectively. For each of the sulphur levels, steels were made with only silicon deoxidization and with aluminum additions of 0.1015, 0.025, 0.050 and 0.10 per cent. The melting medium was an acid-lined high-frequency induction furnace. These steels were forged and rolled and differentiall!. quenched from temperaturcs in the range of 1500O to 1800°F. After this, the A.S.T.M. grain size was determined and plotted as in Fig. I. It will be noted, first of all, that the aluminum-free steels had filler grain size with higher sulphur when heated to 1500, but that this condition was reversed at 1700°. When aluminum was added to produce fine grain size, the steels in the lowest sulphur level were fine-grained only to 1600°. and then only with an addition of one pound of aluminum per ton. The medium sulphur steels werc fine-grained to 1600' with a wider range of aluminum addition. The steels in the highest sulphur level were fine-grained at 1600° over a still wider range of aluminum additions and fine- grained at 1700° with an addition of one pound per ton. Fig. 2 shows curves of the grain-coarsening temperature for these steels and illustrates how sulphur and aluminum combine to give greater inhibition to grain growth than aluminum alone. Only the highest sulphur steels have a grain-coarsening temperaturc above 1700°.. At 1650°, the low sulphur steel is fine-grained only at its peak, while the highest sulphur steel is fine-grained over a wide range. In these tests, one pound of aluminum per ton gave the best results; this is equivalent to about 1 1/2 lb. per ton for commercial condition. IllcQuaid-Ehn tests made on these steels showed the same trend but to a lesser degree. The tests were repeated on a series of S.A.E:. 1015 steels with sulphur levels of 0.02 and 0.03j per cent. Aluminum additions were made in the range from 0.025 to 0.15 per cent. These steels were forged and rolled, normalized at 2000°F. to put them all in the same starting condition, then reheated to various temperatures from 1600" to 1800" and cooled at rates that would allow ferrite precipitation in the austenitic grain boundaries. The results of these tests arc shown in Fig. 3. It will be noted that. up to the temperature of 1650°, there is very little difference in the grain size obtained from the two levels of sulphur. .At temperatures of 1700° and 1750°, however, the lower sulphur steel was fine-grained only with an aluminum addition of 1 1/2 lb, per ton;

Jan 1, 1945

By D. J. Blickwede

PRESENT knowledge of the effects of time and temperature upon stabilization of the austenite-martensite reaction in steel is fairly complete,1-3 but at the time the work described herein was initiated there was no information about the effects of alloy elements on the phenomenon. However, it has been assumed on theoretical grounds that alloy elements, particularly carbide formers, may have a significant effect on stabilization.' The present work was undertaken to provide information about the effect of two common elements, nickel and molybdenum, on stabilization in hypereutectoid and hypoeutectoid steels. Seven induction-furnace melted, 1.2 pct C steels ' with a variation of nickel from 0 to 6 pct and of molybdenum from 0 to 1.0 pct were used for most of the experiments. Along with these a series of 0.4 pct C steels containing 0 to 6 pct Ni were also studied. The chemical compositions of the steels are listed in Table I. Stabilization in these forged, hot-rolled, annealed, and centerless ground steels was measured by aging brine-quenched specimens (aus-tenite temperature, 1800°F) at 95" and 150°F and then determining the change in specific volume produced by subsequent cooling from room temperature to —320°F.³ In presenting the results the decrease in the change in specific volume, ?V, after various stabilization times is used. This is given by ?V -= ?VO - ?V1 where AVO is the change in specific volume on quenching directly to —320°F and aV, is the change in specific volume on quenching to —320°F after stabilizing for time t. In other words, ?V is a direct measure of the amount of martensite that is lost to the subzero quench as a result of stabilization and hence is greater, the longer the aging time or the higher the aging temperature. The results are shown in Fig. 1. The scatter of the data, which are not shown for clarity and brevity, was sufficient to make the relative location of the curves on the ?V axis inaccurate within ±2x10-5 cc per g. However, some generalities appear which are of interest. Effect of Nickel In the 0.4 pct C steels, up to 3 pct Ni has little, if any, effect on the rate or amount of austenite stabilized at 95°F, Fig. la. Increasing nickel from 3 to 6 pct almost doubles the amount of austenite stabilized in a given time. In the 1.2 pct C steels aged at 95°F, increasing the nickel from 1 to 3 pct appears to decrease the amount of stabilization, and a further increase to 6 pct Ni completely eliminates stabilization as shown in Fig. lb (M, of 6 pct Ni steel was below room temperature). The same behavior was exhibited by these steels stabilized at 1500°F, especially after aging for periods longer than 5 hr, Fig. lc. Thus it appears that up to 1 pct Ni has little effect on stabilization at low or high carbon levels. More than 1 pct Ni increases stabilization at low carbon contents and decreases it at high carbon contents. Ward, Jepson, and Rait5 have found that at inter-

Jan 1, 1954

By H. I. Smith

CONTENTS [PAGE Problems of Mining and Processing Mineral Aggregates (TP 1649, by NATHAN C. ROCKWOOD, Min. Tech., Nov. 1943. Discussion by H. I. SMITH, IRVING WARNER and the author) t Mica in War (TP 1749, by RUSSELL G. WAYLAND, Min. Tech., July 1944. Discussion by H. S. SPENCE) 3 Three Roofing-granule Plants in Pennsylvania (TP 1787, by RICHARD M. FOOSE, Min. Tech., Jan. 1945. Discussion by H. I. SMITH)5 Methods of Prospecting and Mining Optical Calcite in Montana (TP 1896, by E. W. NEWMAN, Min. Tech., Nov. 1945. Discussion by W. C. STOLL and FRANK C. ARMSTRONG, and the Glass Sand and a Glass Industry in Puerto Rico (TP 1939, by HOWARD A. MEYERHOFF and J. EARL FRAZIER, Min. Tech., Nov. 1945. Discussion by A. M. SHORT, the author and PHILIP The "Bonanza" Mica Operation of Purdy Mica Mines, Limited, Mattawsn Township, Ontario (TP 2154, by HUGH S. SPENCE, Min. Tech., March 1947. Author's supplement and discussion by JOHN A. BAKER, E. J. LINTNER, and the author) 7 Process for Manufacture of Dead-burned Magnesite and Precipitated Calcium Carbonate from Dolomite (TP 2155, by ROBERT D. PIKE, Min. Tech., March 1947. Discussion by 0. C. RALSTON and the author) 9] Problems of Mining and Processing Mineral Aggregates H. I. SMITH*-Mr. Rockwood has presented a very interesting paper on problems of the mineral aggregate industry in meeting specification requirements, which apparently are ever decreasing in tolerance. May I call attention to a method of mineral separation that may be of value in separating the flat aggregate particles from the more angular ones and possibly the soft particles from the hard. The method is the old Pardee spiral coal separator, extensively used many years ago in the anthracite region for separating rock and bone from anthracite coal.1 The success of the process depends on the relative coefficient of friction of the aggregate particles to be separated rather than on their relative specific gravity. The flat and the soft particles normally will slide more slowly and stay on the inner spiral until they reach the delivery spout at the bottom whereas the round and the angular pieces will work to the outer edge and fall off into a spiral of larger diameter. The capacity of the separator is increased materially by having three inner spirals, with a separate feed for each, on which the particles travel more slowly, and one outer spiral from which the more rapidly traveling pieces slide to the bottom. IRVING WARNER*-I have long been convinced that much of the equipment and methods developed for mineral dressing might be advantageously employed in the mineral aggregates industry, and more particularly in the production of sand and gravel. The two industries are not well acquainted with each other or their problems. They have separate trade publications. The difficulty with the situation is that there are few large sand and gravel plants and few provided with technical services in their own organization or by retainer. This does not refer to engineering organizations but rather to improvement of plant technic in processing.

Jan 1, 1947

By Richard Moldenke

Note.—At the request of the American Society for Testing Materials, this paper wau presented at the New York Meeting, February, 1923, in connection with the "A. S. T. M. Tentative Specifications for Foundry Pig Iron" and The Physics of Cast Iron and Its Bearing on All Cast-iron Products and Specifications for Cast Iron," by William R. Webster. The discussion of this paper was not published by the Institute, having been referred to the American Society for Testing Materials, as these papers were again presented for discussion at the meeting of that Society at Atlantic Cit;, June, 1923. The result of these discussions is shown in the following abstract from the Committee A3 report on cast-iron specifications: During the past year, the adaptability of the tentative specifications for pig iron for the steel and the malleable foundry, in addition to the iron foundry proper, have been studied and suitable changes and rearrangements are being made which appear to cover the situation properly. In spite of the experience of foundrymen to the contrary, there is a persistent call from consumers of castinga for defixute compositions for given lines of castings. To respond to this call for information desired by the consumer—information every modern foundryman should have and guide his procedure with—the committee has requested the Sub-committee on General Cast!rigs to take up this matter with a view of constructing tables of analyses rang? for Important lines of foundry product. These analyses ranges however, are to be given as "recommendgd practice" and not intended for actual spkcification. In this way, the consumer of the foundry product will get the information he wants; the furnace-man will be gulded in the production of his pig irons to prepare for analyses ranges which are more closely standardized and have less of "freak" requirements made by Inexperienced metallurgists; and the foundryman will not be bound by chemical requirements he knows will not work out well with his particular reglonal supphes of melting stock. Doctor Moldenke's paper is published in full as it shows clearly the good results of the Institute's work in 1895 and a comparison of the same with the present knowledge of the metallurgy of cast iron—Bradley Stoughton, Chairman, Iron and Steel Committee. In MaRch, 1895, William R. Webster contributed a carefully prepared scheme for the study of the physics of cast iron to the American Institute of Mining Engineers at its Florida meeting. This summary of the interrelation of the chemical and physical characteristics of cast iron with the operations of daily foundry practice caused a wide discussion of the then little understood though universally used material. Mr. Webster has requested the author to bring the subject up to date and, while glad to comply, he must pay that with all the knowledge that has been gained in the quarter century that has passed since the subject was brought to the attention of the Institute—and we now are pretty familiar with cast iron in all its aspects—there is practically noth-

Jan 1, 1923

• The Venezuelan Trade Mission to the United States announced that Bethlehem Steel Corp. will begin exporting iron ore from its El Pao concession, south of the Orinoco River in Venezuela, in about three months. The ore will be transported by rail from the mines to barges on the Orinoco and transshipped to ore vessels at the coast for shipment to the Sparrows Point, Md., plant. The Latin American business men warned that projected increases in the United States tariff on petroleum imports from Venezuela would force that country into bilateral trade agreements with other countries and would mean drastic curtailment of Venezuelan imports from this country. •Bethlehem, South American Gold and Platinum Co., and U. S. Steel are investigating the possibilities of securing American foodstuff for their South American mining camp commissaries through the International Basic Economy Corp. IBEC buys in quantity to supply its subsidiary companies operating in Venezuela and Brazil. The mining companies will rid themselves of this burdensome task as well as realizing a saving from the bulk purchases of IBEC. •Oliver Iron Mining Co. has begun construction of a fine ore and taconite agglomeration plant at Virginia, Minn. It is expected to be ready in six months. The plant will be used to experiment with the making of clinker cakes and egg-sized lumps by sintering machines and nodulizing kilns respectively; about 1 million tons per year will be produced. • Roof pinning has been adopted at the iron mines of TCI, near Birmingham, to support overlying strata as mining progresses. Favorable results have been obtained in that dilution of the ore has been reduced by 50% which is attributable to this method of supporting the roof. •An American mining engineering team has gone to Turkey for a two-year assignment assisting Turkish government agencies in the $45 million ECA development, mechanization, and construction of cleaning plants for the Zonguldak coal field, 200 miles east of Istanbul on the Black Sea. The group consists of James Beeley, John E. Good, John S. Lambright, David Renshaw, and Charles R. Weir, all of the Paul Weir Co. •Arthur F. Taggart describes a new way of training engineers by emphasis on broad, basic engineering courses on page 460 of this issue. •Lawrence T. Tierney, chairman of the National Bituminous Coal Advisory Council, released a report stating that the increase in oil imports since the latter part of 194$ has caused significant damage to the U. S. fuel economy. It has reduced the strength of and employment opportunities in the coal, domestic petroleum, and transportation industries, as well as in related service and supplier fields. •Women, camels, and donkeys are the beasts of burden of the Sahara, according-to the UNESCO World Review. •Increased demand for magnesium sheet in airplane construction ana other phases of the national security program have led Alcoa to establish a sheet magnesium rolling division at its New Kensington, Pa., works which will begin operation shortly. Novel prospecting methods being used by the USGS in its search for uranium include: shock-mounted instruments in light trucks,. Geiger-counter probes lowered into augur holes, and experimental airborne prospecting.

Jan 4, 1950

By M. S. Seltzer

In a previous paper1 it was shown that activation energies for steady-state creep in lead sulfide single crystals varied with the concentration of electronic defects. For n-type lead-excess crystals, values for the creep activation energy, Qc, decreased from 2.9 to 2.2 ev as the carrier concentration increased from 1017 to 1017 electrons per cu cm, while Q, increased from 1.6 to 2.3 ev for p-type sulfur-excess crystals as the concentration of holes increased from 6 X 1017 to 1018 per cu cm. It was also shown in Ref. 1 that the Q, values could best be correlated with the sum of the self-diffusion activation energies in PbS, i.e., for a given concentration of electrons or holes Q, = QPb + Qs, where Qpb and QS are the activation energies for diffusion of pb210 and s35 in PbS. This result suggests that creep rates are controlled by at least two atomic defects, one for lead migration and one controlling sulfur transport. It would be most desirable to interpret these creep energies in terms of an atomic defect disorder model for lead sulfide. Studies of creep rates as a function of sulfur pressure2 indicate that the defects controlling creep rates are singly ionized lead and sulfur vacancies, VPb and Vs. This hypothesis can be more firmly established by determination of Q, under conditions of constant atomic defect concentration rather than constant electronic defect concentration as has been previously done. Therefore, several measurements have been made of Q, on crystals whose con- centration of lead vacancies or sulfur vacancies has been fixed by equilibration under appropriate sulfur pressure and temperature. It was indicated in Ref. 2 that high-temperature isotherms are available which show how the concentrations of various atomic point defects in PbS vary with composition over the entire homogeneity range for the compound. Two such isotherms are shown in Fig. 1 for 900" and 1000°K. Utilizing these isotherms the concentration of a given defect, say Vbb, may be held constant over a particular temperature range by adjusting the sulfur pressure as the temperature is changed. Thus the concentration of one defect suspected of controlling creep rates may be held constant while other defect concentrations vary. The apparent activation energy for formation of these defects can be obtained from the isotherms giving their concentration as a function of sulfur pressure. Activation energies for creep obtained under conditions of constant defect concentration can then be compared with defect formation energies and certain possible atomic defects can be eliminated as creep-controlling species. We have performed creep experiments as a function of temperature at a stress of 244 g per sq mm under conditions which fixed the lead vacancy concentration, V', at 1016, 3.2 x 1016, and 3.2 x 1017 cm-3, and one were the sulfur vacancy concentration, Vs, was held at lo17 cm-3. The results are presented in Fig. 2 as creep rate, k, vs reciprocal of absolute temperature, 1/T. Specimens 34, 35, and 36 were deformed under constant lead vacancy concentration while specimen

Jan 1, 1969

By Richard Moldenke

Note.—At the request of the American Society for Testing Materials, this paper wau presented at the New York Meeting, February, 1923, in connection with the "A. S. T. M. Tentative Specifications for Foundry Pig Iron" and The Physics of Cast Iron and Its Bearing on All Cast-iron Products and Specifications for Cast Iron," by William R. Webster. The discussion of this paper was not published by the Institute, having been referred to the American Society for Testing Materials, as these papers were again presented for discussion at the meeting of that Society at Atlantic Cit;, June, 1923. The result of these discussions is shown in the following abstract from the Committee A3 report on cast-iron specifications: During the past year, the adaptability of the tentative specifications for pig iron for the steel and the malleable foundry, in addition to the iron foundry proper, have been studied and suitable changes and rearrangements are being made which appear to cover the situation properly. In spite of the experience of foundrymen to the contrary, there is a persistent call from consumers of castinga for defixute compositions for given lines of castings. To respond to this call for information desired by the consumer—information every modern foundryman should have and guide his procedure with—the committee has requested the Sub-committee on General Cast!rigs to take up this matter with a view of constructing tables of analyses rang? for Important lines of foundry product. These analyses ranges however, are to be given as "recommendgd practice" and not intended for actual spkcification. In this way, the consumer of the foundry product will get the information he wants; the furnace-man will be gulded in the production of his pig irons to prepare for analyses ranges which are more closely standardized and have less of "freak" requirements made by Inexperienced metallurgists; and the foundryman will not be bound by chemical requirements he knows will not work out well with his particular reglonal supphes of melting stock. Doctor Moldenke's paper is published in full as it shows clearly the good results of the Institute's work in 1895 and a comparison of the same with the present knowledge of the metallurgy of cast iron—Bradley Stoughton, Chairman, Iron and Steel Committee. In MaRch, 1895, William R. Webster contributed a carefully prepared scheme for the study of the physics of cast iron to the American Institute of Mining Engineers at its Florida meeting. This summary of the interrelation of the chemical and physical characteristics of cast iron with the operations of daily foundry practice caused a wide discussion of the then little understood though universally used material. Mr. Webster has requested the author to bring the subject up to date and, while glad to comply, he must pay that with all the knowledge that has been gained in the quarter century that has passed since the subject was brought to the attention of the Institute—and we now are pretty familiar with cast iron in all its aspects—there is practically noth-

Jan 1, 1923

By R. D. Longyear

[Some Problems Involved in the Interpretation of Diamond-drill-hole Sampling and Surve ing (paper by J. J. Collins, Mining Tech., Jan. 1946). ............... I Geologic Interpretation of Magnetic Exploration on the Mesabi Range, Minnesota (paper by R. H. B. Jones, Mining Tech., July 1946) ................... 2] DISCUSSION R. D. LONGYEAR.*-Mr. Collins is to be commended very highly for the brief summary he has made of the currently used methods of taking diamond-drill sludge samples and the principles involved in evaluating the results. This paper should stimulate further discussion and research on this vitally important problem. It is particularly imperative that geologists and engineers know when assay results on sludge recovery can be accepted quantitatively and when they must be considered only qualitatively. In most cases where the sludge recovery is less than 95 per cent or more than 125 per cent, it is safest to consider the assays as of qualitative value only. Certain cases, however, are known where a relatively small proportion of the sludge sampling will give a reasonably accurate measure of the value of the total sample. One such case is ore in which the valuable mineral is of approximately the same specific gravity as the waste mineral, such as chalcopyrite in a massive pyrite body. The essential point is to determine the degree of accuracy of sludge sampling in any given drilling project and to weigh the results accordingly. It should be emphasized, however, that sludge sampling can be made reliable in many localities where careless practice produces unreliable results. In many instances, it is desirable to empty the core barrel in the core shack instead of at the drill, so that the engineer can examine the core as it first comes from the core barrel. It should be pointed out, however, that the drill * E. J. Longyear Co., Minneapolis, Minnesota. runner should be permitted to study the core to guide his future drilling. It is hoped that with the return of more normal conditions after the war geologists, engineers, contractors, and manufacturers will be able to carry on more research along the lines of improved core-barrel design and drilling technique with the objective of increasing core recovery so as to eliminate as far as possible the necessity of relying upon sludge samples. H. M. ROBERTS.*-Whoever in the future will have to do with the search for ore bodies and their exploration will have frequent occasion to refer to the clear and comprehensive summary on diamond-drilling methods by John Collins. His review of the experience of the last 40 years in this technique is invaluable. As Dr. L. D. Ricketts wrote in 1932, "The principles on which an art is founded are usually few and necessarily basic in nature, but he who wishes to achieve the power to select his aides and give success to important undertakings that may be intrusted to him in the future must ordinarily undergo years of drudgery in order to gain the experience that will enable him to distinguish such fundamentals through the haze of reinforcing detail that clothes and tends to disguise them."[t] Ricketts went on to say that since the beginning of the century there has been much

Jan 1, 1946

By M. T. Hepworth, A. K. Stewart

Iron containing 0.1 pct A1 and -0.9 pct P by weight was internally oxidized in the temperature range 900° to 1300° C, where the bcc structure is stabilized by phosphorous. By measuring the depth of penetration of oxygen with time in an internally oxidized zone for an imposed surface oxygen potential, oxygen permeability was determined. The dgfusion coefficient of oxygen in iron was then calculated using known solubility data, yielding the expression: where Do is the diffusion coefficient of oxygen in bcc iron in sq cm per sec and T is temperature in OK. RECENTLY Hepworth, Smith, and Turkdoganl measured the diffusivity of oxygen in bcc iron and reported the temperature dependence of diffusivity from data determined in the a, and 6 temperature ranges. Subsequently Swisher and Turkdogan' have measured the diffusivity of oxygen in fcc iron. Internal oxidation techniques were employed by these investigators and in this current study. The analysis of this technique is developed by wagner3 (presented in English by Hauffe4 and Rapp 5). In this present study bcc iron stabilized by phosphorous was used to determine oxygen diffusivity in the temperature range 900° to 1300°C. Meijerin 6 has studied oxygen permeability in this temperature range using bcc iron stabilized with 5 pct Sn. Other inves- tigators who have studied oxygen permeability in bcc iron at other temperatures are Schenck et al., 7 Bohen-kamp and Engell, 8 and Bradford. EXPERIMENTAL Electrolytic iron of 99.99 pct purity was alloyed to contain 0.897 pct P and 0.093 pct Al. The maximum weight percent phosphorous required to stabilize bcc iron between 910" and 1392°C is 0.51 pct as determined by Haughton,10 0.42 pct by Roquet and jegaden," and 0.58 pct by vogel,12 with the latter value preferred by Hansen.13 Microprobe analysis indicated that there was no segregation of the phosphorous either before or after permeability studies; therefore, the quantity of phosphorous added was assumed to be sufficient to stabilize the bcc structure. Furthermore, the permeability results of studies on this alloy agreed substantially with interpolated values from previous data on bcc iron.' An ingot of the Fe-P-A1 alloy was hot-rolled to a l-in.-thick slab. Specimens were machined to dimensions: 13/8 by $ by 1/4 in. The experimental apparatus and procedure used have been described before.' A constant oxygen potential was established by passing argon and hydrogen through a column of oxalic acid dihydrate, which has a water vapor pressure which is well-known as a function of temperature. Slab specimens were exposed to a gas mixture sufficiently lean in oxygen to prevent the formation of a surface oxide for predetermined temperature for selected times. The specimens were then quenched, sectioned, and examined metallo-graphically. All quenched specimens were iron-plated to provide protection from the outside sample edge during polishing. Fig. 1 shows a typical microstruc-ture for a specimen oxidized at 953°C for 48.00 hr at a water vapor-to-hydrogen pressure ratio of 0.20. DISCUSSION AND RESULTS The following equation was derived by Hepworth et al.' from Wagner's kinetic expressions for internal oxidation:

Jan 1, 1969

By A. Andreas

New Mexico established an annual record by producing 38,897,741 bbl. of oil during 1940. This was approximately 6 per cent greater than the 1939 production of 36,746,840 bbl. The daily average produc-tion was 106,569 bbl. New Mexico retained its position as the seventh oil-producing state. The recommendations of the United States Bureau of Mines were followed by the Oil Conservation Commission in setting the monthly state allowable. At the beginning of the year the average top allowable for each qc-acre unit was 40 bbl. and at the close of the year it was 36 bbl. Remedial work by the operators has been extremely beneficial and satisfactory in reducing the gas-oil ratios in various fields. Gas formerly blown into the air is now being processed by numerous casinghead plants. The Oil Conservation Commission, with the full cooperation of the Proration Office and operators, has taken bottom-hole pressure surveys and has done considerable remedial work in various fields. Two new oil fields and one gas field were discovered in New Mexico during 1940. Numerous extensions to the existing fields were made. Some of these were definitely wildcats in the same townships designated as fields and some, although called extensions, were more than 3 miles from production. Lea County continued to be the largest oil-producing county in the state, with a production of 33,976,394 bbl. It had the largest number of completions during 1940, with 303 oil wells, 9 gas wells and 13 dry holes—a total of 325 wells. Eddy County was the next most active county, with 239 completions, of which 163 were oil wells, 8 gas wells and 68 dry holes. It produced 4,405,158 bbl. of oil during the year. The increased activity in Eddy County and the completion of a large number of producing oil wells have created a transportation problem that can be solved only by additional pipe-line facilities. During the year Eddy County was unable to produce 1,500,000 bbl. of its allowable oil, because there was no pipe-line outlet. There were 601 wells completed in New Mexico in 1940, of which 478 were oil wells, 22 gas wells and IOI dry holes. This was a decline of approximately 9.5 per cent in the number of completions compared with 1939, when 659 wells were drilled. Southeastern New Mexico Lea County.—The largest producing field in Lea County was the Monument field, with 6,894,475 bbl.; followed by Eunice with 6,559,348 bbl. and Vacuum with 4,743,065 bbl. The Hobbs pool, which for years was the largest producing field in the state of New Mexico, was fourth with 3,790,477 bbl. The Vacuum pool was the most active area, having 68 completions, of which 67 were oil wells and one was a dry hole. Only one new field was discovered in Lea County during 1940; the discovery well was in the Caprock area, the Livermore State No. I, in the SE. 1/4 SE. 1/4 sec. 30, T. 12 S, R. 32 E. This well was drilled to a

Jan 1, 1941

By A. T. Robinson, J. E. Dorn

The electrical resistivities of aluminum alloys containing CU, Ge, Zn, Ag, Cd, and Mg were found to increase linearly with the atomic percentage of the solute atoms. Application of Linde's rule to these data suggests that each aluminum atom contributes 2.5 electrons to the metallic bond. ALTHOUGH aluminum invariably exhibits a Jt\. valence of three in ionic solids, it does not follow necessarily that its valence in the metallic state is also three. As a matter of record, many properties suggest that the number of bonding electrons in metallic aluminum is less than three. For example, as shown in Fig. 1, the atomic radii1 of the metallic elements in the solid state decrease with increasing atomic number at the beginning of any one period. The atomic radius of aluminum, however, is greater than that which would result from a regular decrease in atomic radius with increasing atomic number, suggesting that the number of bonding electrons in aluminum is somewhat less than three. Correlated with the anomalously large atomic radius of aluminum is its abnormally low melting temperature. As the atomic numbers increase in any one period, the melting temperatures of the metallic elements increase.' As shown in Fig. 2, however, the melting temperature of aluminum (13) is only slightly greater than that of magnesium (12). Again the number of bonding electrons in metallic aluminum appears to be nearer two than the expected value of three. In addition Ageev and Ageeva3 alculated the electron density distribution in the aluminum lattice. A comparison of such electron density curves for various assumed valence states of aluminum with experimentally determined curves suggests that the actual number of bonding electrons in metallic aluminum is between two and three. Hume-Rothery and Raynor', " have suggested that the above-mentioned abnormalities are associated with the overlapping of the Brillouin zones of metallic aluminum when it is in the usual face-centered cubic structure. The importance of the number of bonding electrons in metals has been extended recently into the field of mechanical properties. While formerly it was thought that the plastic properties of alpha solid solutions were primarily dependent upon the lattice strain induced in the solvent by the solute, it is now known that the difference in the number of bonding electrons of the solute and solvent also has its influence on the plastic properties."1' In order to achieve a satisfactory correlation of the effect of alloying elements on the plastic properties of aluminum alloys,"'T however, it was necessary to assume that the number of bonding electrons contributed by aluminum was about two rather than the expected value of three. It appeared to be desirable, therefore, to seek other criteria for evaluating the number of bonding electrons contributed by aluminum to its alpha solid solutions, especially in view of the practical as well as the theoretical importance of the effect of valency on the plastic properties. Norbury' was perhaps the first to illustrate that the increase in resistance of alpha solid solutions is associated with the differences in valence of the solute and solvent metals. In a series of illuminating investigations Linden-'' has shown that the electrical

Jan 1, 1952

By J. C. Allen, E. V. Herring

CHILE EXPLORATION CO's. oxide plant at Chuquicamata, the largest of its kind, started in 1915 with initial operations at the rate of 10,000 tons of ore per day. Anaconda Copper Mining Co. acquired the controlling interest in 1923 and in the next few years modernized the plant and mine, extending operations to a nominal capacity of 490 million lb of electrolytic copper yearly by 1942. Plant production averaging 495.7 million lb of copper per year was maintained for the eight-year period extending from 1941 to 1948 inclusive. During the World War II production reached its highest level when in 1944 the output was 531.8 million lb. The maximum production for any one month was 49.6 million lb, achieved in May 1947. E. A. Cappelen Smith, consulting metallurgist for M. Guggenheim's Sons, worked out the first process for the treatment of Chuquicamata copper oxide ore about 1913, and directed a staff of 20 young engineers operating a pilot plant at Perth Amboy, N. J., on three shifts for an entire year. The copper is extracted from the oxide ore by a hydro-metallurgical treatment described in detail by T. A. Campbell in AIME Transactions, Vol. 106, Copper Metallurgy, 1933. The Oxide Plant is divided into five main operations as follows: (1) Crushing, (2) Leaching, including dechloridizing and sulphur dioxide treatment, (3) Tailing disposal, (4) Electrolytic precipitation, (5) Smelting and melting. Crushing The present Primary Crushing Plant has been in operation 25 years, during which time 4,342,112 cars of 70 tons net capacity have passed through the dumpers. The ore as received from the mine is frequently blocky and up to 5 feet in section. It is reduced to 9-in. size by two 60-in. gyratory crushers, and transported to the east and west ore bins by 60-in. conveyors. In the secondary crushing operation the ore is first reduced to 2 to 3-in. size by five standard 7-ft cone crushers and two No. 10 gyratories. This product is then reduced to 3/8-in. size by fifty-two 48-in. vertical Symons disc crushers and is transported by belt conveyors to the loading bridges from which it is charged° into the leaching vats. Conveyor belt No. 14 which serves the eight vats in the east section of the leaching plant has transported over 125 million tons of ore, which is a record for any type of conveyor. This 60-in. belt travels at a speed of 600 fpm and carries loads up to 5500 tons per hr. Leaching The ore is leached in 14 vats, averaging 13,500 short tons net capacity each. These vats are lined with a natural mastic which adequately resists the sulphuric acid leaching solutions. The leaching process as presently conducted comprises soaking the ore with successive volumes of leaching solution and spent electrolyte and withdrawing successive volumes of enriched solution from the vat to a total of approximately 3.2 million gal. The first 1.6 million gal of this volume withdrawn is called strong solution and contains about 35 parts of copper per 1000. The balance of 1.6 million gal subsequently withdrawn is stored in a

Jan 1, 1952

By A. Andreas

New Mexico established an annual record by producing 38,897,741 bbl. of oil during 1940. This was approximately 6 per cent greater than the 1939 production of 36,746,840 bbl. The daily average produc-tion was 106,569 bbl. New Mexico retained its position as the seventh oil-producing state. The recommendations of the United States Bureau of Mines were followed by the Oil Conservation Commission in setting the monthly state allowable. At the beginning of the year the average top allowable for each qc-acre unit was 40 bbl. and at the close of the year it was 36 bbl. Remedial work by the operators has been extremely beneficial and satisfactory in reducing the gas-oil ratios in various fields. Gas formerly blown into the air is now being processed by numerous casinghead plants. The Oil Conservation Commission, with the full cooperation of the Proration Office and operators, has taken bottom-hole pressure surveys and has done considerable remedial work in various fields. Two new oil fields and one gas field were discovered in New Mexico during 1940. Numerous extensions to the existing fields were made. Some of these were definitely wildcats in the same townships designated as fields and some, although called extensions, were more than 3 miles from production. Lea County continued to be the largest oil-producing county in the state, with a production of 33,976,394 bbl. It had the largest number of completions during 1940, with 303 oil wells, 9 gas wells and 13 dry holes—a total of 325 wells. Eddy County was the next most active county, with 239 completions, of which 163 were oil wells, 8 gas wells and 68 dry holes. It produced 4,405,158 bbl. of oil during the year. The increased activity in Eddy County and the completion of a large number of producing oil wells have created a transportation problem that can be solved only by additional pipe-line facilities. During the year Eddy County was unable to produce 1,500,000 bbl. of its allowable oil, because there was no pipe-line outlet. There were 601 wells completed in New Mexico in 1940, of which 478 were oil wells, 22 gas wells and IOI dry holes. This was a decline of approximately 9.5 per cent in the number of completions compared with 1939, when 659 wells were drilled. Southeastern New Mexico Lea County.—The largest producing field in Lea County was the Monument field, with 6,894,475 bbl.; followed by Eunice with 6,559,348 bbl. and Vacuum with 4,743,065 bbl. The Hobbs pool, which for years was the largest producing field in the state of New Mexico, was fourth with 3,790,477 bbl. The Vacuum pool was the most active area, having 68 completions, of which 67 were oil wells and one was a dry hole. Only one new field was discovered in Lea County during 1940; the discovery well was in the Caprock area, the Livermore State No. I, in the SE. 1/4 SE. 1/4 sec. 30, T. 12 S, R. 32 E. This well was drilled to a

Jan 1, 1941

By Mark J. Klein, A. H. Clauer

The Snoek peak induced by solute nitrogen in chromium was studied. A rapid quenching rate is required to maintain nitvogen in solution in sufficient concentrations to be detectable by internal-friction techniques. An expression for the tertninal solubility, c, of nitrogen in weight pevcent is log,,c = -4130/T + 1.05. The diffusion of nitrogen in zhromium determined by internal friction is SNOEK&apos;S theory1 of the stress-induced ordering of interstitial solute elements in the bcc lattice has been used to deduce information on the behavior of interstitials in a number of bcc metals. Under the proper conditions, internal-friction studies of "Snoek peaks" permit a determination of diffu-sivities, solubilities, and precipitation kinetics of interstitial elements. Internal-friction studies of this type have been reviewed by Nowick,&apos; Wert,= Powers and Doyle,4 and others. The behavior of interstitial atoms in Group V-A metals and iron has been rather extensively studied in this way, and results are reasonably self-consistent. However, the study of interstitial elements using internal friction in the Group VI-A metals—tungsten, molybdenum, and chromium—is much less clear. Thus far, internal-friction studies have revealed a peak in tungsten tentatively attributed to carbon5 and a peak in chromium associated with nitrogen. In chromium, Bungardt and Preisendanz6 observed a peak at 180°C for a frequency of -1 cps which they associated with nitrogen. More recently, de Morton7 determined the diffusivity of nitrogen in chromium from studies of a nitrogen peak at 160°c for a frequency of -1 cps and from elastic aftereffect measurements. The objective of this investigation was to study the nitrogen peak in greater detail, to obtain information on the behavior of nitrogen in chromium. This information is of interest because nitrogen is known to have an embrittling effect on chromium. However, efforts to deduce the role played by nitrogen in influencing the mechanical behavior of chromium are handicapped by lack of information on its behavior and distribution in chromium. EXPERIMENTAL PROCEDURES The chromium wires used in these studies were drawn from arc-melted iodide-chromium stock that had been extruded, swaged, and centerless-ground to 0.25 in.-diameter rods. Internal-friction measurements were made in an evacuated torsional pendulum similar to the one described by Kê,8 utilizing wires 0.048 to 0.030 in. in diameter. A series of analyses of the fabricated wires showed that the major impurities were approximately 100 ppm Fe and a combined interstitial content of 50 to 100 ppm C, O, N, and H. A typical interstitial analysis of the wires after processing is 15 ppm C, 2 ppm H, 50 ppm O, and < 5 ppm N. Interstitial concentrations were determined by vacuum-fusion, combustion-conductimetric, and micro-Kjeldahl analyses. In general, vacuum-fusion analysis yielded a lower nitrogen concentration than did micro-Kjeldahl analysis. For consistency, the nitrogen concentrations reported in this investigation were determined by the former method. Heat treatments were carried out by encapsulating the specimens in quartz tubes containing argon. The fabricated wires were annealed at 1150°C for 1 hr to produce uniform recrystallized grain size of about 0.015 mm. Nitrogen and carbon were added to the fabricated wires by encapsulating them in a quartz tube containing ammonia or methane, and annealing them at 1150°C for 48 hr. In some instances, carbon was also introduced by coating the wires with carbon black prior to annealing.

Jan 1, 1965