Search Documents

By Michael F. Dunn, Francis S. Kendorski

The fall of rock from strip coal mine highwalls continues to be the largest single source of fatal accidents, so methods to improve highwall stability through improved blasting practices were investigated in the field. This paper covers the results of a project to improve, using existing and proven technology, unstable highwall conditions through better blasting practices in Appalachian strip coal mines. Better borehole blasting agent distribution and optimization of burden, spacing, and delay periods allowing satisfactory breakage with minimal backbreak were the objectives. At a selected field site, geologic conditions were closely examined with regard to joint orientation and spacing, and resulting slope stability considerations. Utilizing surface blasting concepts of trying to achieve flexural failure of the rock mass both horizontally and longitudinally by appropriate relationships between burden, spacing, and hole length, as well as delay time sequence to achieve optimal confinement and breakage, successful results were achieved. A test series of eight blasts was completed and the resultant highwall monitored by repetitive photography. Actual blockfalls could be measured and the stability for each blast design thus quantified. The study of drilling and blasting economics along with equipment performance led to an economic model of blast parameters and the identification of blast design cost benefits. The work demonstrated that small strip mining companies are able to achieve a more stable highwall excavation utilizing presently available technology, equipment, and explosive products at improved operational cost and safety.

Jan 1, 1983

By David B. Scott

The Mogollon mining district, New Mexico, has received little public attention, although for 15 years it has been the leading silver producer of the state; it is situated in a region remote from the principal lines of travel, and its activities have usually been limited to the operations of two or three companies. The value of the total production of the district in the 44 years of its history has been estimated at $15,000,000. For the years 1904 to 1917, inclusive, the output was: gold, $4,370,000; silver, 10,042,000 oz.; copper, 874,862 lb.; total value, approximately $10,500,000. In 1913 the district contributed 80 per cent. of the total silver production of New Mexico, but in 1917 only 41 per cent., due to serious interruption in the operations of the leading producer. Since 1914 the silver output has diminished one-half, and the present high value of silver is nearly offset by the increase in cost of production. The output of gold has rarely exceeded 35 per cent. of the total for New Mexico. The ratio of silver to gold, by weight, has averaged 46:1 based on the whole output of the district. Location and Topography The town of Mogollon is 75 mi. (121 km.) by a poorly located highway ,. from the nearest railroad terminals, at Silver City and Tyrone. All supplies are transported by motor trucks and teams. The area, sometimes called the Cooney Mining District, lies on the western flank of the Mogollon Mountains, which occupy the western part of Socorro County. The elevations drop steeply on the west to the valley of the San Francisco River, adjacent to the Arizona boundary. The topography is very rugged, the whole area being sharply dissected; deep canyons with steep gradients and rugged walls are characteristic of the whole western slope of the Mogollon Range. The main canyons i run east and west, and usually maintain a flow of water during the entire year. As would be expected in a region of such deep dissection, the mines are generally dry. The mountain ridges between the canyons have altitudes varying from 7000 to 10,000 ft. (2130 to 3050 m.) and drop sharply, on their western face, to the floor of the San Francisco Valley at an elevation of 5000 ft. (1525 m.). Erosion has been rapid, and the

Jan 1, 1920

By Wilfrid R. Foster

The industrial importance of the sillimanite group of minerals depends upon the beneficial properties exhibited by porcelains and refractories in which substantial amounts of these minerals are utilized as raw materials. The presence of "sillimanite" (now known to be the closely related mineral, mullite) in conventional porcelains and refractories has been known since before the turn of the century. As early as 1906 German investigators observed a direct correlation between the "sillimanite" content of a porcelain and its electrical and mechanical properties. Acting upon this discovery, U. S. Bureau of Standards investigators during World War I developed improved pyrometer tubes and spark plug porcelains, by increasing substantially the amount of "sillimanite" at the expense of quartz. The success of these experiments, first reported in 1918, at once aroused a lively interest in the location of natural sources of sillimanite and its related minerals. As a result of diligent search, the large andalusite deposits in California were discovered in 1919. Within the next several years large deposits of kyanite and sillimanite in India and kyanite in the United States had been reported. The search for these minerals in quantity, by both private and governmental agencies, has continued unabated during the ensuing forty years. A number of domestic deposits of kyanite have been worked during the past 30 years. Of these, only the Virginian and South Carolinian deposits are currently in substantial production. The only commercial andalusite production in the United States has been in California and Nevada. A dumortierite deposit in Nevada, known since 1917 but ignored for want of a commercial use, began production in 1925. A topaz occurrence in South Carolina has yielded a small production since about 1940. Domestic production of andalusite, dumortierite and topaz had virtually ceased by 1950. There has never been any commercial development of domestic sillimanite deposits. Kyanite has been mined almost continuously in India since about 1922. The remoteness of the large deposits of Indian sillimanite had caused it to be neglected until 1949. In that year sillimanite production began, and it has continued to the present. South African andalusite has been marketed from the 1930's until the present time. From 1944 to 1955 Kenya, British East Africa, was an important producer of kyanite. Commercial deposits of kyanite in Ontario, Canada should soon be in production. The first production of kyanite in Europe began in Austria in 1953. No commercial deposits of mullite are known anywhere in the world. It is of interest to note that synthetic mullite, which as "sillimanite" first elicited interest in the A12O3-rich aluminosilicate refractories, has enjoyed a marked increase in production in recent years. This is a result of the gradual depletion of known deposits of high-quality kyanite and related minerals."' Composition The sillimanite group includes kyanite, andalusite, and sillimanite, all having the same chemical composition (A12O3•SiO2) but different physical properties. Two other minerals, dumortierite and topaz, are also included in

Jan 1, 1960

By R. W. Waterfill

MANY existing ore deposits of valuable metals have been worked out in their upper surface levels and the continued productivity of these mines is dependent on their extension to greater depths in the earth. The maximum depths at present reached are about 6000 to 8000 ft. below the surface, with no evidence of an impoverished ore vein. These mines are widely distributed; some of the best known are in South Africa, Brazil, India and in the western sections of the United States. Among the factors which increase the difficulty of working these mines at increasing depths are hoisting, rock pressure and temperature. The manner and effectiveness with which these problems are met will, no doubt, determine in a large measure the ultimate depths to which any mine can be profitably worked. The most critical of these three factors at present is the increase in temperature with depth. The high temperature and humidity in many of these mines at present is severely detrimental to the health of the workers and greatly hampers their efficiency. Some have almost reached a condition in which the human system cannot survive. The problems involved in the cooling and ventilation of mines have all been ably analyzed and presented in previous articles. For this reason, only a resume of conditions affecting the cooling and conditioning of deep and hot mines will be given in this paper before attention is directed to possible methods of improving atmospheric conditions in the working levels.

Jan 1, 1929

By Bruno V. E. Nordberg

Hoisting is one of the earliest endeavors of man with machinery, for hoisting was probably used by the early Egyptians. Treadmills were used for general hoisting until early in the nineteenth century and it was a short step only to attach a Watt steam engine to the rope drum of a hoist. One of the earliest steam hoists was built for a coal mine at Frisne, near Valenciennes, France. It was a remarkable piece of engineering created by James Watt in 1811, using a wooden drum on a vertical shaft. This followed the crude hoist by Holtzhausen in 1803, which used a drum of wood on a horizontal shaft.' In this country there were examples of crude mine hoists, which have been developed into the efficient machines in use today. African and Australian mines show examples of both extremes, and have an array of fine hoisting equipment exemplified in those built by British manufacturers. The influence of both English and American engineering in hoisting is interestingly evident in Canada. The information available to the writer does not reveal this to be true of South Africa, although American-built hoists have been furnished. Mining camps develop their own style of equipment, adapted to local conditions. For instance, the Butte mining district adheres to the straight drum with friction clutches, because of the great number of levels from which hoisting is done or to which men and material are lowered and the necessity for hoisting or lowering unbalanced. The north Michigan copper country uses both straight and cylindroconical drums and hoists continually in balance, so that the drums are not clutched to the main driving shaft. The Joplin mining district, Missouri, has its own peculiar small hoists. Other individual mines or localities in which a number of mines have been developed show individualistic types of hoists, depending upon their particular problems. In each instance, however, the particular problem must be carefully analyzed, as conditions are seldom so near the same that a number of identical hoists can be used to advantage.

Jan 1, 1940

By William J. Priestley

In the manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and clastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungston, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured—by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. Design of Gun Forgings In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun arc made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The clastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge. As the stresses set up in the walls of the gun during firing are mostly "tangential," all physical tests are taken in this direction. Due to the length of the forgings, these tangential test bars are always taken at right angles and transverse to the direction of flow of the metal in forging. Furthermore, test bars taken across the grain of the metal will more frequently expose defects and foreign inclusions in the steel than will bars

Jan 1, 1922

By Alfred H. Bell, George V. Cohee

In 1941 Illinois produced 134,139,000 bbl. of oil, or 9.5 per cent of the total for the United States, and ranked fourth among the states. The production for 1941 declined 9.2 per cent from the previous year's total of 147,647,000 bbl. Daily average production for 1941 was 366,000 bbl. At the beginning of the year daily production was slightly more than 326,000 bbl. and it remained at appoximately that amount until June, when there was a slight increase. The increase continued until the peak of 431,260 bbl. daily was reached for the week ending Oct. 4. Daily average production at the end of the year was approximately 387,500 barrels. The increased production during the last half of 1941 was largely due to the rapid development of the Johnsonville field, Wayne County, the Rural Hill field, Hamilton County, and the Benton field, Franklin County—new fields discovered in the current year (Fig' 1)—and the Woodlawn pool, discovered in 1940. Discoveries In 19 counties in southern Illinois, 44 new fields were discovered in 1941 (Fig. 2 and Table 2), and extensions to 40 fields were successfully completed (Table 3). At the end of the year there were 10,496 wells in the fields discovered since Jan. I, '937, as compared with 71965 wells at the end Of '940. The area proved for production in the new fields increased from 78,040 acres at the beginning of 1941 to 97,483 acres at the end of the year (Table I)—an increase of 19,433 acres, of which 9,955 acres are in the fields discovered during the current year, and the remainder of 9,478 acres in extensions to pools discovered earlier. Drilling During the past year, 3838 wells were completed in Illinois (Table 4), of which 2912 were oil producers, 13 were gas producers and 913 were dry holes; 76 per cent of the wells drilled were producers. Of the total number drilled, 591 wells are classified as "wildcat" and of these 84 (1 in 7) were successful in obtaining production. The results of an investigation to ascer-tain the reason for the locations of the wildcat wells are set forth in Table 5. Of the 591 wildcat wells, the 292 known to have been located by scientific methods were 21.6 per cent successful. The total footage of wildcat wells drilled in 1941 was 1,341,743 ft., of which a total of 216,995 ft. was drilled in successful wells. Exploration MEthods Subsurface geology and geophysics, largely the reflection seismograph, are still the principal methods used in exploration and development in the state. The number of seismograph parties operating throughout the year was as follows: seven parties on Jan. I, 1941; five on Apr. I; four On July I; eight on Oct. I; fifteen on Jan. 1: 1942.

Jan 1, 1942

By T. B. Counselman

PRobably the earliest concentration of iron ore in this country was carried on in the northeastern magnetite areas. Magnetic concentration was relatively simple and gave a concentrate that, after agglomeration, and in spite of beillg high in phosphorus hecause of the dry concentrating methods then in use, was satisfactory blast-furnace feed. Production from the northeastern magnetitc area languished after the discovery and development of the Lake Superior ores, where there was seemingly an unlimited tonnage of high-grade ore, first the Michigan ores, and subsequently the still larger deposits of Minnesota. For years only the higher grade, direct shipping ores of the Lake superior district were mined. Those of Michigan, and of the Vermilion Range in Minnesota, were hard ores and came principally from underground mines. The softer ores of the Mesabi came partly from underground mincs, but mostly from the enormous deposits that could be worked by open-pit methods. The costs of ore from these open-pit deposits, even with the high initial cost of stripping, were so low that the underground mines of the Mesabi could hardly compete. The so-called Old Range ores, of Michigan and of the Vermilion Range of Minnesota, were hard and lumpy, and opened UP the burden in the blast furnace, therefore making possible harder driving with greater output. Also, some of these Ores were of such grade and physical characteristics that they were suitable for charge ore in the open hearth. These ores, therefore, commanded a price premium. and could compete with the softer, finer, but cheaper, Mesabi ores. The big tonnage reserves, however, are on the Mesabi. and it is these big open-pit deposits that contitue- our stock pile of iron ore, from which we are drawing so heavily during this war period. On the western end of the Mesabi the ore was found to be high in silica, and not suitable as furnace feed. As early as 1902, attempts were made to concentrate this so-called wash ore and by 1910 the first washing plant was put into operation. The Process was very simple, consisting essentially of a sizing and washing operation, with scalping screens, logwashers and tables, which later were replaced by classificrs. Ore particles finer than I00 mesh were deliberately wasted, because these fines were undesirable in the furnace. Fortunately, these tailings were impounded, and already are being reworked. Before long some of the low-grade ores began to require more elaborate treatment than the simple washing operation and, tables having been discarded because of their low capacity, in favor of classifiers, jigs were next introduced. These were able to discard coarser pieces of tailing than classifiers. Jigs are in active use today, various improvements having been made in their design and application. Various other machines and methods of concentration have been tried from time to time, and have in turn been discarded for more improved processes., The latest and most important process that has been 38

Jan 1, 1944

By Robert A. Colten, Frederick C. Hull, Robert F. Mehl

It is known that pearlite forms from austenite by a process of nucleation and growth, and that the rate of formation of pearlite may be described by a rate of nucleation and a rate of growth.l,2 The manner in which these two quantities operate to produce the observed isothermal reaction curve has been analyzed in a paper published in I939.3 Two types of process were described: (I) that in which nucleation occurs at the grain boundaries of the parent phase, with the nodules growing toward the centers of the grains, initially as hemispheres and then after impingement as roughly radial-columnar structures; and (2) that in which nucleation occurs generally, with the nodules growing to full spheres until impingement with other growing nodules restricts growth. Both cases are met in the formation of pearlite from austenite (Fig. I);2,4 the former, occurring near the knee of the S-curve, has been named "grain-boundary transformation," and the latter, occurring at temperatures near Ael, has been named "group-nodule transformation." In developing our knowledge of the factors that determine the rate of formation of pearlite from austenite, it is important1,2 to obtain data on the rate of nucleation and the rate of growth of pearlite. Such data, when obtained near the knee of the S-curve, will furnish information of use in understanding the factors that affect hardenabil-ity; when obtained at higher temperatures, such data will be useful in understanding the behavior of steels that during heat-treatment react to pearlite.2 It is the purpose of this paper to present data on the rate of nucleation and the rate of growth of pearlite in dependence upon composition, grain size, temperature, and the degree of homogeneity of the parent austenite. The studies are restricted chiefly to plain carbon commercial steels." Previous Data on Rate of nucleation and rate of Growth Data on the rate of nucleation and the rate of growth of pearlite have been published by Scheil and Lange-Weise,5 by Mirkin and Blanter,6,7 by Meh1,l and by Dorn, De Garmo and Flanigan.2, It is difficult to interpret the data, for in most cases too little information is given on austenitizing temperatures and times, the state of homogeneity of the austenite (presence or absence of carbide, etc.), austenite grain size, and mode of formation of pearlite at the temperatures given. Except for the approximations of Mehl and the work of Dorn, austenite grain size was disregarded, though it is well known

Jan 1, 1942

By J. H. Richards, G. Derge, W. Peifer

A WIDE Variety of metallurgical defects in steel have commonly been attributed to the presence of excessive amounts of hydrogen. These defects include flakes in rails and forgings, cracks in welds, and blisters in enameled ware, They have been related to hydrogen largely by circumstantiat evidence because the proper sampling and analysis of steel for hydrogen has been known to be difficult and because no general agreement has existed with regard to the relative suitability and accuracy of available methods. The need for a direct approach to these problems has been widely recognized. This general situation has been well described in the publications of the British committee on the Heterogeneity of Steel Ingots,' and current approaches to the problem were reviewed in a recent symposium of the AIME.I2 The plans described by the present authors at that meeting have now matured satisfactorily and will form the basis of this paper. The principal object of this paper will be to describe the methods of sampling and analysis which have been developed and to illustrate the usefulness and limitations of these methods by citing their application to a specific problem, The first problem selected for investigation was the behavior of hydrogen in rail steel. This was chosen because the occurrence of shatter cracks in rails has received a great deal of study over a long period of time. The defect can be controlled by the expensive procedure of slow in However, it may be hoped that a better understanding of the factors influencing the hydrogen content of rails will lead to a more efficient control of this problem. Rails provide a good starting point for a more general study of hydrogen in steel because they provide a cross-section large enough to develop cracks, Yet small enough for convenient handling and sampling. Rails were also selected because they arc made from plain carbon steel and it was felt that the initial work should not be complicated by the effects introduced by alloying elements. The considerations which determined the original planning of this study should be reviewed. The inherently complex nature of most hydrogen problems requires that a large amount of data must be collected for any particular case. This in turn means that any analytical procedure should be as rapid and simple as possible. The same objective of speed is indicated by the fact that it may finally become desirable to use hydrogen analysis in process control. It is also known that hydrogen is highly fugitive and that any procedure which facilitat~s early analysis of the sample without prolonged or irregular storage has distinct advantages. The most important previously reported methods of analysis may be classified into three general groups: (I) Vacuum fusion, (2) Vacuum extraction (without melting), (3) Total combustion.

Jan 1, 1949

By Helmut Thielsch

MeTallographic specimens whose surfaces are to be investigated are too thick to allow either light or electrons to pass through them for microexamination by transmission. This difficulty is overcome with optical microscopes by illuminating the surface through the objective lens. For electron microscopes best results are obtained by preparing thin replicas of the surface of the specimen, placing them in the microscope and passing the electron beam through them. Since electron microscopes represent a rather recent invention, they have found little application as compared with optical microscopes. This is true because, aside from the cost of new equipment and development of new techniques, some of the older replica methods necessitated the destruction of the surface from which a thin transparent replica was obtained. In other processes in which the surface is preserved, either too tedious a procedure is required, unsuited to "mass-production" requirements of industrial laboratories, or replicas of insufficient contrast and sharpness are produced. In general, investigations with the electron microscope involve five steps: (I) polishing the surface of the metal specimen, (2) proper etching of the surface, (3) preparing the suitable replica from the surface, (4) examination and phorography in electron microscope and (5) interpretation. Preparation of Metal Surfaces Usual metallographic polishing is generclly satisfactory. It is important though that the final polish be applied very carefully, since otherwise evidence of a small amount of deformation might show up even on relatively deeply etched surfaces. A high-power microscope should be used to determine the suitability of the polish and etch. This, of course, is not different from optical examinations, but in these, if a deep etch is used, the problem is less serious. It is frequently difficult to detect with optical microscopes poor polishing aside fiom superficial scratches before etching. Figs. I and 2 show micrographs of "well" and "poorly" polished nickel etched by immersing the sample for 20 min. in a solution containing 8 grams cupric sulphate in 40 C.C. of concentrated HCl and 40 C.C. of Hz0 (Marble's reagent). The sample shown in Fig. I was polished in its final stages for 5 min. on a carborundum wheel followed by ro min. on a rouge wheel, whereas the sample shown in Fig. 2 was polished only I min. on the rouge wheel. Generally, this procedure does not guarantee that the surface of the specimen will be either undistorted or deformed. It was applied here merely to show the effects Of good and poor polishing. To the experienced investigator, plastic deformation is

Jan 1, 1946

By M. C. Dow

Belt conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stone-crushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. General Reliability It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 /12 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. Loading the Belt It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined the to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1948

By Bernard Kopelman

The particle size of tungsten metal powder used to make tungsten wire for use in radio tubes and incandescent lamps must be closely controlled if the highly desirable feature of nonsagging is to be achieved. Our knowledge of factors affecting the particle size of tungsten powder has been limited by lack of any extensive literature on the subject. There are no publications in the English language discussing this problem in any but the most general terms. In this paper the published experimental information on this subject is reviewed. Based on the published data and some experimental data obtained by the author, a general theory of factors affecting the particle size of tungsten metal powder obtained by reduction of the oxides in hydrogen is offered. The various forms of the tungsten oxides and tungsten metal used in the experiments described were those prepared by commercial processes, so that the experimental results obtained on a laboratory scale would be more directly applicable to actual commercial reduction conditions. The effects of time of reduction, temperature. and concentration of water vapor in the hydrogen were observed by counting microscopically the particle distribution obtained. Such a method is very time-consuming, but the data obtained by this method are more reliable and more fundamental than those obtained by any of the several instruments available for measurement of particle size. Review of the Literature Until the year 1912, tungsten powder was prepared commercially by reducing tungstic oxide in the presence of carbon or one of its compounds (such as glycerin or ethylene glycol), usually by firing the mixture in a closed fire-clay crucible. The resultant powder contained about 95 per cent tungsten.' When reduction of tungsten oxides by H² was introduced Commercially,²,³ several investigators became concerned with the equilibria between tungsten metal and its several oxides in an atmosphere of hydrogen and water vapor.4-l3 While these many investigations were in fair agreement on the equilibria WO³ + H2 = WO2 + H2O and WO2 + 2H2 = W + 2H2O there arose considerable controversy as to the chemical composition of the oxide between WO³ and WO², because of very poor agreement on the equilibrium constant of this intermediate oxide reduction reaction. The controversy on this intermediate oxide has been in progress for more than 100 years. Thus Malguti,14 in 1835, decided it was WO2.56 In 1857, Riche15 proposed the formula W³O8. Usler,16 in 1865, confirmed the existence of WsO8 and further proposed W1O1l. In 1897, Desil7 agreed upon W²O8 but also found W5O14.

Jan 1, 1947

By Alfred H. Bell, George V. Cohee

In 1941 Illinois produced 134,139,000 bbl. of oil, or 9.5 per cent of the total for the United States, and ranked fourth among the states. The production for 1941 declined 9.2 per cent from the previous year's total of 147,647,000 bbl. Daily average production for 1941 was 366,000 bbl. At the beginning of the year daily production was slightly more than 326,000 bbl. and it remained at appoximately that amount until June, when there was a slight increase. The increase continued until the peak of 431,260 bbl. daily was reached for the week ending Oct. 4. Daily average production at the end of the year was approximately 387,500 barrels. The increased production during the last half of 1941 was largely due to the rapid development of the Johnsonville field, Wayne County, the Rural Hill field, Hamilton County, and the Benton field, Franklin County—new fields discovered in the current year (Fig' 1)—and the Woodlawn pool, discovered in 1940. Discoveries In 19 counties in southern Illinois, 44 new fields were discovered in 1941 (Fig. 2 and Table 2), and extensions to 40 fields were successfully completed (Table 3). At the end of the year there were 10,496 wells in the fields discovered since Jan. I, '937, as compared with 71965 wells at the end Of '940. The area proved for production in the new fields increased from 78,040 acres at the beginning of 1941 to 97,483 acres at the end of the year (Table I)—an increase of 19,433 acres, of which 9,955 acres are in the fields discovered during the current year, and the remainder of 9,478 acres in extensions to pools discovered earlier. Drilling During the past year, 3838 wells were completed in Illinois (Table 4), of which 2912 were oil producers, 13 were gas producers and 913 were dry holes; 76 per cent of the wells drilled were producers. Of the total number drilled, 591 wells are classified as "wildcat" and of these 84 (1 in 7) were successful in obtaining production. The results of an investigation to ascer-tain the reason for the locations of the wildcat wells are set forth in Table 5. Of the 591 wildcat wells, the 292 known to have been located by scientific methods were 21.6 per cent successful. The total footage of wildcat wells drilled in 1941 was 1,341,743 ft., of which a total of 216,995 ft. was drilled in successful wells. Exploration MEthods Subsurface geology and geophysics, largely the reflection seismograph, are still the principal methods used in exploration and development in the state. The number of seismograph parties operating throughout the year was as follows: seven parties on Jan. I, 1941; five on Apr. I; four On July I; eight on Oct. I; fifteen on Jan. 1: 1942.

Jan 1, 1942

By B. E. Cornish

Most technical and statistical data published on pyrophyllite relating to production figures, uses, markets and sales, have in the past traditionally linked the mineral with talc and soapstone. This is due to several common superficial physical properties resulting in substitute uses and applications. However, these minerals are not similar in chemical composition and do not generally occur in a similar geological environment. Pyrophyllite now stands on its own in the marketplace-particularly in ceramic applications-due to the combination of excellent heat shock and creep resistance properties of the mineral. The increase in pyrophyllite use in the field of ceramics indicates the continuing realization of these marked unique properties. Several new fields of ceramic applications, previously the preserve of high-alumina materials, have been developed on the intrinsic properties of pyrophyllite. Pyrophyllite is an aluminum silicate with the molecular formula of AI2O34SiO2H2O. It would be more appropriate to group pyrophyllite with such materials as kyanite, diaspore, andalusite, and certain high-alumina clays in relation to its general applications (Stuckey, 1928). These materials all have good beat shock resistance properties at high temperatures and are widely used for the manufacture of refractories. For those reasons they are interchangeable in some applications. Pyrophyllite also has many uses in nonceramic applications, the most important to date being as a substitute for talc in fillers. The major pyrophyllite mining operations are located in the US, Japan, Korea, Canada, and Australia, where the mineral is widely used as a raw material for general ceramic, mineral filler, and dilutant applications. Commercial Applications Pyrophyllite was first used in the last century for lining stoves and fireplaces, and also in the carving and polishing of ornamental objects. The rise in industrial demand for new products and applications resulted in the introduction of pyrophyllite as an alternative, mainly for talc and soapstone. Industrial filler applications followed for paint, paper, cosmetics, rubber, pesticides, crayons and pencils, and bleaching soap. The first use of pyrophyllite in ceramic applications was prior to World War II, in the manufacture of ceramic cladding tiles in the US. This was followed by the production of kiln furniture refractories and whiteware when pyrophyllite was offered by suppliers in North Carolina as an alternative to some local clays. The largest tonnages of pyrophyllite used today are in refractory linings in steel ladles in Japan, as seen in Table 1. The consumption of pyrophyllite in Japan is second only to clay and chamotte among refractory raw materials used. Recently this technology has been adopted in Australia. Japanese and Australian practice has resulted in appreciable technical and economic benefits, particularly when pyrophyllite is used in combination with zircon. The potential growth for this application is substantial if US and European steelmakers follow. Investigation and research into the properties of pyrophyllite determined the following main advantages of pyrophyllite-based ceramics: high corrosion resistance for molten iron, steel, and slags; good heat shock resistance; good indices of deformation under load and hot creep resistance (refractories); and increase in mechanical strength of whiteware products promoted by a better distribution of mullite in finished products (also obtained at lower firing temperatures than normally required in production of triaxial ceramics). White cement

Jan 1, 1983

By M. C. Dow

Belt conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stone-crushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. General Reliability It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 /12 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. Loading the Belt It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined the to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1948

By B. H. Bergstrom, D. D. Crabtree, C. L. Sollenberger

Experimental data is given for several natural minerals on the load required for the fracture of single specimens over a very wide size range. The experimental results are compared with published data, such as for coal specimens from 30 to 64 in. in size. Correlations of the specific energy (per unit mass) required for fracture with specimen size are given as functions of specimen shape and the experimentally observed load-size relationships. These correlations are discussed with reference to comminution theory. Comminution, through compression or impact, can result only if sufficient force, or energy, is applied to a specimen of a given size. The relation of specimen size to force requirements has not been adequately considered previously. For single particle fracture, it was previously shown 1 that the specific energy (energy, e, per unit mass, M) at fracture of single glass spheres was inversely proportional to the product size modulus, k, as indicated in the equation: e/M = C/k [1] This was found true not only for numerous glass specimens of the same nominal size but was true for all nominal sizes tested from 1/8 to 1 in. Also, it was observed that the smaller spheres required a greater specific energy at fracture than the larger spheres and consequently had a smaller product size modulus. However, the relationship giving the required fracture energy as a function of specimen size was not further elaborated upon. This paper will extend the development of the feed size effect on specific fracture energy for brittle materials. SPECIFIC ENERGY-FEED SlZE RELATIONSHIPS FROM PREVIOUS DATA For the particular glass spheres tested in the previously described experiments,' it can be shown, as on Fig. 1, that the specific energy varied inversely as the 4/3 power approximately of the feed size, F, in the span of nominal sizes ranging from 1/8 to 1 in. The load at which a 3-in. diam glass sphere (a crystal gazer's ball) was broken was within the range predicted by an extrapolation of this energy-feed size relationship. The product size distribution from this

Jan 1, 1963

By D. T. Peterson, F. A. Schmidt, J. D. Verhoeven

The velocity of mig-ration of these solutes in thorium metal due to a high amperage dc current was measured at several temperatures. All three solutes migrated in the same direction as the electron flow. Diffusion coefficients were combined with the migration velocities to predict the steady-state concentration profile. Electrotransport was shown to be an effective method of removing carbon, oxygen, and nitrogen from thorium and resistance ratios several times larger than for crystal bar thorium were achieved. However, the maxirnum attained purification was well below the predicted values, apparently due to some form of contamination. THE migration of solutes in metals when a high current density dc current is passed has been known for many years. This phenomenon has been the subject of a number of reviews published in recent years.l~* Many of the earlier investigators of electromigration of interstitial solutes interpreted the direction and velocity of migration on the basis of a charge on the solute particle. This interpretation is unclear because, in a given experiment, one cannot separate the contributions to the force moving the solute which arise from the charge on the solute in an electric field gradient and the momentum transfer from the scattering of the electrons or holes. There have been only a few quantitative measurements of interstitial migration velocities and some of these have been characterized by poor accuracy or by errors in the analysis of the experiment. The electrotransport mobilities of carbon, nitrogen, and oxygen in thorium were determined by observing the rate of movement of a discontinuity in the concentration profile. This method was used by Carlson el a~.~ to determine the mobilities of interstitial solutes in yttrium and its advantages are discussed in that paper. The specimen is essentially a pair of semi-infinite, bar-type diffusion couples. The electro-transport velocity was measured by observing the displacement of the mean concentration point in a measured length of time. The diffusion coefficients were calculated by the Grube method from the concentration profile. The transport mobilities and diffusion coefficients can be used to predict the concentration profile in an electrotransport experiment of a given time, current density, and specimen length. At long times a steady state will be reached such that the natural logarithm of the concentration of each solute varies linearly along the bar with a slope which is equal to the velocity of the migrating solute divided by its diffusion coefficient. The estimation of the purification potential of electrotransport is discussed by ~erhoeven.' A comparison of the concentration profile and the purification which should be expected from known solute velocities and diffusion coefficients with that which is obtained in an experiment can be very useful in indicating whether the maximum possible purification has been achieved. EXPERIMENTAL METHOD The apparatus used in this study consisted of a sample chamber which was equipped with two electrodes, a sight glass, and a flange for mounting to a high-vacuum system capable of obtaining pressure of 2 x lo-? Torr. The chamber was made of stainless steel and was 4 in. in diam and 6 in. long. The seal between the electrodes and the chamber was made with "0" rings and compression bushings. The thorium specimens were threaded and screwed into tantalum "U"-shaped adapters attached to the ends of the electrodes. This arrangement is shown in Fig. 1

Jan 1, 1967

By G. R. Speich

The precipitation of the Feab and Fe,Ti Laves phases (MgZn, type, C14) from Fe-Nb and Fe-Ti solid solutions, respectively, has been studied in the temperature range 500" to 800°C using hardness measurements, light and electron microscopy, and X-ray and electron diffraction. The Fe-Nb alloys contained 0.96, 1.67, and 3.80 pct Nb and the Fe-Ti alloys 3.5, 5.8, and 8.8 pct Ti. In both systems only the equilibrium Laves phase is formed, with nucleation occurring at grain boundaries, at dislocations, and in the matrix. No cellular precipitation or transition phases were observed. The precipitation of the Laves phase in a fine dispersion leads to significant hardening in both systems. The hardness of the aged alloys is proportional to the reciprocal of the square root of the interparticle spacing. The maximum solid solubility of titanium in a! iron is 9.0 pct Ti at 1280°C. THE precipitation of the FezNb and FezTi Laves phases (MgZn2 type, C 14) from Fe-Nb and Fe-Ti solid solutions, respectively, has been investigated as part of a continuing study of the mechanisms of precipitation from ferritic binary iron-base alloys. The iron-rich portions of the Fe-Nb and Fe-Ti phase diagrams are shown in Fig. l(a) and l(b). The Fe-Nb diagram is essentially that given by ansen' with the more recent work of Hume-Rothery and Gibson2 added. Goldschmidt3 indicates that the FezNb Laves phase has a solubility extending from 32 to 55 wt pct Nb. The Fe-Ti diagram is also essentially that reported by Hansen.l The recent results of Nishimura and kamei, Murakami, Kimura, and Nishimura,' indicate that the FezTi Laves phase has a solubility extending from 22.5 to 30.5 wt pct Ti. The L/6 + FezTi eutectic temperature of 1298°C indicated by Kornilov and oriskina' has been adopted. The addition of niobium or titanium to iron lowers the 6 — y transformation temperature and raises the y — a! transformation temperature. This results in a closed y field in the Fe-Ti system, but the lower solubility of niobium in a! (6) iron results in a eutec-toid, 6 — y + FezNb, at 1200°C, and a peritectoid, y + FezNb —-a, at 989°C in the Fe-Nb system. The maximum solubility of niobium is reported to be 4.5 wt pct in 6 iron,' 1.0 wt pct in y iron,7 and 1.8 wt pct in a iron.' Some results from the present work indicate that the maximum solubility in a! iron is actually less than 0.96 wt pct Nb. The maximum solubility of titanium in a! (6) iron is somewhat uncertain since the early work of To faute and Butting-haus indicated a value of 6.0 wt pct while later work of Kornilov and Boriskina6 yielded a value of 14.0 wt pct. The present work indicates that the maximum solubility is actually 9.0 wt pct. In both systems the phase in equilibrium with the iron-base solid solutions is a Laves phase (Mg znztype, C14), FezNb or FezTi. Both of these Laves phases have a wide range of Solubility. The precipitation-hardening behavior of Fe-Nb or Fe-Ti alloys has not been studied extensively. Genders and Harrison' reported that binary Fe-Nb alloys hardened upon aging. Peter and Fisher7 studied the mechanical properties of Fe-Nb and Fe-Ti alloys quenched from different phase fields.

Jan 1, 1962

By David H. Browne, John F. Thompson

The literature dealing with the physical constants of nickel is so fragmentary and unrelated that a synopsis presents unusual difficulties. It is only within the last few years that investigators have understood the importance of placing on record not only the determinations they have made but also the composition, physical treatment, and past history of the material investigated. For this reason much of the earlier literature is valueless. Determinations have been made of the same physical constants on samples differing widely in origin, composition, and treatment, and the results differ widely among themselves. In the first place nickel is almost as flexible a term as steel. Its physical properties are widely influenced by its composition and treatment. It absorbs large quantities of gases and is exceedingly difficult to prepare in a state of chemical purity comparable to gold, silver, or copper. It is vitally affected by thermal and mechanical treatment. Hence in the following pages the recorded literature, where quoted, must be accepted with a certain reserve and used, as far as possible, as a check on later observations, in which these important factors are noted. In every case where new determinations are given, an attempt has been made to record all available information concerning the composition and treatment of the material used so that the data may serve as stepping-stones toward a wider knowledge of the properties of the metal. As this synopsis is an attempt by men of metallurgical training to do what should long before have been done by physicists, it is to be expected that certain errors may have crept in. Any corrections or suggestions

Jan 1, 1921