Search Documents

By P. Nyul, S. Caplan, M. F. Lamorte, T. Gonda

Therrnal resistance is measured on GaAs laser diodes in the temperature range 77" to 300°K. These data show that typically the thermal resistance increases fifteen times from 77 to 300°K. The increase is attributed to the decrease in thermal conductivity of Gds. Nornzalized thermal-resistance experimental and calculated from published thermal-conductivity data) values are compared and good agreement shown. In many practical applications, it is desirable to obtain high average power output from laser diodes. Average power output is determined in large measure by the external efficiency and thermal resistance of the diode.'-3 The average input power with which a laser diode may be pumped is dependent on the thermal resistance. Thermal resistance has been studied over the temperature range from 77" to 300°K which is usually of interest in practical applications. This correspondence presents data on thermal resistance for GaAs laser diodes and compares them to values calculated from thermal-conductivity data. Junction heating arises from three distinct components: 1) joule heating, 2) nonradiative recombinations, and 3) reabsorption of radiation. In high-threshold lasers, joule heating predominates.4 Typically, the nonradiative recombination is not negligible and contributes significantly to junction heating. The loss caused by reabsorption may be of the order of the joule-heating loss.' The fabrication and the geometry of laser diodes have been described in other publications.5 The data presented were obtained from diodes which were fabricated from the same region of a wafer to minimize differences. Fig. 1 shows four types of heat sinks employed in this study. In types 1 and 2, the laser cavities are alloyed; pressure contacts are employed in types 3 and 4, and indium is plated on the inside faces to improve the intimacy of contact between the diode and the heat sink. The thermal resistance R is defined by the following relationship: where AT is the junction-temperature rise above the heat-sink temperature for the diode power dissipation Pd. For measurement of thermal resistance, a direct current is passed through the junction, in the range from 1 to 50 pct of threshold. The diode is placed in the laser mode by superimposing a current pulse of low-duty cycle on the direct current.3 Junction-temperature rise is obtained from the time-resolved laser spectrum at the leading edge of the current pulse.' Typically, the laser line shift is 2.5A per OK. The resolution employed in these experiments is 0.5A; therefore, the accuracy in the temperature measurement is 0.2K. Typically, the temperature rise is 2" to 20°K. The power dissipation is the difference between the dc power input, and the radiation power exiting the diode. The measurement accuracy is less than 1

Jan 1, 1968

By F. P. Dewey

Bone-ash cupels have been used from time immemorial to absorb litharge, and accompanying oxides, in assaying. Doubtless, also, from the earliest days cupels have been most unjustly blamed for much poor assaying. It has long been known that the precious metals go with the litharge into the cupel. This occasions a loss of precious metals and reduces the results of the assay. There have been many investigations of cupels and the most diverse views have been expressed, the extremes being the statements of Lodge1 that every cupel has some effect upon the loss in assaying telluride ores and of the Campredons2 that coarse and fine and hard and soft cupels all give the same loss of silver when cupelling the same weights. The truth lies between these statements and much nearer the latter. In a vast majority of cases the influence of the cupel is not dominant and is outweighed by other conditions, particularly the temperature of the cupelling bead. At the Spokane meeting of the Institute I presented a paper on the Assay and Valuation of Gold Bullion,3 which recorded the results of many hundreds of assays made in the Mint service under everyday commercial conditions, which of necessity differ from scientific conditions. In following this matter up, for the purpose of increasing the accuracy of our commercial methods of bullion assays, the question of the absorption of gold by the cupel was found to be a most important one and was taken up for investigation. In a lesser degree, the silver absorption is important and interesting, but at resent it appears to be far more complicated and, while many figures showing silver absorption may be found through this paper, much further investigation is required to put the subject upon a satisfactory basis.

Jan 1, 1918

By H. A. Bedworth, W. H. Bassett

The amount of oxygen present in refined copper bears an important relation to the effects of various impurities on physical properties of copper, as well as the effects of reducing gases at higher temperatures. It seems fitting at this time, when the effects of reducing gases on copper are being discussed, to describe methods that have proved satisfactory for the determination of oxygen and sulfur, and to present some results obtained by investigation of these methods in the authors' laboratory. The procedure for the determination of sulfur is closely interrelated with that for oxygen and has, therefore, been included. It was first proposed by Hampe1 that oxides in copper could be accurately determined by the loss in weight sustained by finely divided copper when reduced at red heat in pure hydrogen, or by the weight of water produced. Hampe's method was later modified by Archbutt,2 who established the accuracy of the method and demonstrated that equally accurate results were obtained by noting the loss in weight or by weighing the water formed. The determination of oxygen by heating in carbon monoxide has been proposed by West.3 In our hands this method has given slightly lower results than obtained by heating in hydrogen. Heath4 found that the loss in weight after heating in hydrogen did not represent the true oxygen as cuprous oxide but included also gases derived by the metal from the fuel and refining in the furnace, and any trace of mechanically held moisture. He found, further, that the copper after ignition retained hydrogen equivalent to about 0.01 per cent. Heath proposed to determine the amount of occluded gases by preliminary ignition for 20 min. in pure carbon dioxide—and to correct the error caused by absorbed hydrogen by subsequent ignition and cooling in carbon dioxide, finally replacing this gas with air.

Jan 1, 1926

By M. Earl Volin, M. Adnan Goksel

The hydro thermal agglomerating process described (U.S. Pat. No. 3,235,371, 1966)* is different from the cotzventional high-temperature processes. Green pellets or briquettes made with mixtures of moist iron-ore concen- trates and burned or hydrated lime fines are hardened in an azttoclave at 198°C and under steam pressure for 112 to 5 hr, with or without previous drying. Under the neutral conditiotzs, oxidation of magnetite does not occur as in the conventional processes. The resulting azzlomerates-- are hard and resistant to abrasion and weathering, and they do not disintegrate in the Under test. The equipment required for the process is not complicated, and favorable operating costs are projected because of the low temperamre and efficient heat recuperation. A low capital investment makes the process attractive even when the annual pellet production is below a million tons.

Jan 1, 1970

IN CHAPTER I it was shown that the approximate market value of the copper produced at the twelve big Porphyry mines from 1905 to 1931, inclusive, was $2,821,300,000. This represented the refined metal ready for shipment to the consumer. In addition, at least $50,000,000 worth of gold and silver had been produced, more than $30,000,000 coming from the Utah mine alone. Consequently, the revenues totaled about $2,871,300,000, as shown in Table 58. Society paid this sum for a given quantity of metal that it wanted for industrial use. Where did the money go? Who were the direct beneficiaries of the creation of this new wealth? These questions this chapter will answer in a general way. Because some necessary data are not available, an exact tabulation in detail can not be made, but Table 58 is believed to reflect with reasonable accuracy the disposition made of the aggregate income from the twelve operations. The word "operations" is used advisedly because the complexity of corporate relations precludes the possibility of picking out companies, as could be done if each enterprise were an independent entity such as Miami, for example. Some explanation of the table and some elaboration of the items under "Outgo" is desirable. In the first place, it is assumed that the sum of surplus current assets existing in various treasuries at the end of 1931 was substantially equivalent to the “new” money that actually was put into the enterprises as a group. Less than $20,000,000 in new capital was realized from securities sold by the Utah Copper Co., the remaining funds coming from earnings. In respect to some of the others, such as Chuquicamata, Inspiration, and Andes, the amount of new money was much greater. However, of the two items-total new capital invested and total current surpluses-the former

Jan 1, 1933

By T. W. Guy

During the past three years the Surface Preparation Committee of the American Mining Congress Coal Operators' Committees has been collecting data on dewatering and drying washed coal, and on screening coal in representative plants in the Eastern and Central bituminous fields. Because of wide variations in bed moisture, such data can be compared only after deducting the bed moisture. It was found that practically every company used a different routine for moisture sampling and determinations. Some reported the moistures as total moistures, others as surface moistures, air-dried moistures, or oven-dried moistures. For most of the reports it was necessary to estimate, from a consideration of the bed moisture and other data available in a given case, corrections to be made in order to obtain surface-moisture figures as a common basis for comparison. At any plant, and regardless of bed moisture, the percentage of surface moisture remaining in a product when the dewatering, or a given stage of the dewatering, has been completed, is the real measure of what has been accomplished. The descriptions and data given with Fig. 1 show that surface-moisture figures show relationships that would not be shown by total moistures. Therefore bed moisture should be deducted, or, if more practicable, the surface moisture of the products should be measured direct. A preparation engineer finds one per cent, or even a part of one per cent, of surface moisture a very important consideration in the results of his efforts to find the most effective and economical methods of reducing and controlling the surface moisture in his products within the required limits. Therefore it is important for him to have accurate measurements of surface moisture with minimum uncertainty as to whether they sometimes include less than the surface moisture and at others all of the surface moisture plus an unknown part of the bed moisture. The Problem We know that pieces of coal have a capacity for holding water: (1) inside themselves, which is a natural characteristic of the bed from

Jan 1, 1938

By Edwin F. Nelson, Charles Wirth, Gustav Egloff, C. D. Maxutov

The treatment of emulsified crude oils has been a problem for years in the petroleum industry. Until comparatively recently various methods of settling with and without chemicals have been used with indifferent success. Since wells have been acidized, emulsified crudes have been produced, which add considerably to the need for improved methods of treatment. The presence of large quantities of salts in the oils from acidized wells has presented several new problems to the industry. The use of hydrochloric acid in well treatments has caused the formation of sodium, magnesium, and calcium chlorides by interaction with the dolomitic limestones. These salts dissolve readily in the water normally present in the oil, and they are therefore incorporated in the emulsified oil. The crystalline salts have also been found in the oil, prevented from settling by protective films such as asphalt, resins and petrolatum. In some instances, free hydrochloric acid has been found. The salts may be present in crude oil in amounts ranging from a few pounds to over 1000 lb. per 1000 bbl. of oil. The transportation of these crude oils through pipe lines has led to erosive and corrosive effects, which are a tremendous cost to the petroleum industry. During 1937, more than 1,200,000,000 bbl. of crude oil was transported through pipe lines. Of this quantity approximately 10,000,-000 bbl. was water, and considerably more than 50,000,000 lb. was salts. If the crude oils were treated at the producing wells to remove the salts and water, an appreciable saving would be possible. The treatment would not be difficult, since it has been found that these oils are more easily treated at the time they are produced than after the aging and more stable emulsification that occur before they reach the refinery. Since great costs are involved in the use of these salty crudes at the refinery, treated oils essentially free of salts would naturally command a premium. The real added costs lie in refining salt-containing crude oils. Severe corrosion of refinery equipment in both topping and cracking installations has appeared in many refineries. Chemicals such as ammonia, lime and

Jan 1, 1938

By T. Cameron Kenney

INTRODUCTION Whereas the design of rock slopes in open-pit mines is done largely by mining engineers and geologists, the design of slopes in overburden at this point in time is a problem for which civil engineers or geotechnical engineers are best prepared to deal. The reasons for this situation are to be found in the educational curricula and the technical journals of the two groups, where soil mechanics has received little attention by mining engineers and geologists, and rock mechanics has similarly received little attention by civil engineers. In ten years' time this paper will hopefully be considered by young mining engineers to be a repeat of the material that they studied at university. However, even in ten years time I believe that the civil (or geotechnical) engineers will be extensively used as consultants on overburden- slope problems of open pit mines because mining companies will find this more expedient than maintaining their own geotechnical staff, special field equipment and special testing laboratories. For this reason, the purpose of this paper is not to condense several university soil mechanics courses into a twenty-page text for mining engineers and geologists. Rather, the purpose of the paper is to offer a general explanation of various factors affecting slope stability so that mining engineers and geologists will have a better understanding of the behaviour of overburden soils in slopes. A great deal has been written in soil mechanics literature on the subject of slope stability. No attempt will be made to reference all this material but rather only a selected number of references will be cited. Excellent general treatments of the subject of stability of overburden slopes are available (1,2,3,4). Further information of a more specialized nature is to be found in such publications as the Journal of the Soil Mechanics and Foundation Division of the American Society of Civil Engineers, Geotechnique (printed by the Institution of Civil Engineers, England), Canadian Geotechnical Journal, and the proceedings of the conferences of the International Society for Soil Mechanics and Foundation Engineering. FACTORS INFLUENCING SLOPE STABILITY There are two general scales of slope-stability problems, gross stability and local stability. Gross stability refers to large volumes of soil, and gross instability would involve large rotational-type shear failures. Local stability refers to something much smaller and examples

Jan 1, 1972

By A. H. Grobe, F. N. Rhines

THE constitution of the indium-zinc alloy series has been investigated by Wilson and Peretti,1 who determined the liquidus and eutectic temperatures by the conventional method of cooling curves and the eutectic composition by analyzing eutectic exudations. Recent developments affecting the availability of indium and consequent increased interest in its applications make a more complete knowledge of the constitution of its alloys desirable. As a part of a program for the reexamination of the constitution of indium alloys by precision methods, the indium-zinc phase diagram [ ] (Figs. I and 2) has been redetermined in its entirety. The eutectic temperature (143.5°C.) reported by Wilson and Peretti has been confirmed exactly, but their value of the zinc concentration at the eutectic, 4 per cent, was found to be high; the new value is 2.8 per cent of zinc. There is also a rather large difference between the forms of the liquidus curves of Wilson and Peretti and those found in the present studies. The solidus curves herein have been located for the first time and the limits of solid solubility have been tenta-

Jan 1, 1944

By John F. Kendrick, Paul D. Cornelius

This paper is a progress report of a study the authors are making of the sucker-rod pump, considered as a vibrating system with one degree of freedom, with forced vibrations and with viscous damping. Dr. S. Timoshenko's formula is given, defining such a system. Each factor is considered in respect to the problem of operating sucker rods, and the zone is pointed out in which the mathematics do not apply to the sucker-rod pump, because of its variable mass. This general theory is interpreted in the light of nearly two years of testing wells in the field, and correlating the results of other tests. The motion of the pumping mechanism is a vibration. The string of sucker rods vibrates with a natural frequency. The motion of the plunger is the result of adding together these two vibrations, and is modified by a damping or friction factor. The controlling factor appears to be the ratio of the period of the natural vibration of the rod string to the period of the vibration of the pump. The first conclusion is that a definite value of this ratio, which is below resonance and is probably not greater than 0.5, should not be exceeded in order to assure satisfactory performance from the sucker rods. The second conclusion is that the component parts of the pumping equipment should be selected to give the smallest practical period of the natural vibration, and when this does not permit operation at a safe speed and give the required plunger displacement, a longer polished-rod stroke should be used. While the quantitative results are but rough approximations, the qualitative analysis of pumping problems on this basis promises to be of considerable value in diagnosing the cause of poor performance and prescribing suitable remedies. The trouble that results, whenever it becomes necessary to crowd the sucker-rod pump, to take potentials or to handle increasing volumes of water, is responsible for the belief that this type of pump is not equal to present day needs, and that it is only a question of time before some other pumping device will take its place. Of the troubles experienced, it is not surprising that the frequency of sucker-rod failures should

Jan 1, 1937

By M. M. Austin

Pure metallic tantalum, from a practical standpoint, is one of the newer developments in the metal field. Although it was used as filament in incandescent lamps in 1906, only within the last, five years has the metal been available in sufficient quantity and suitable form for more general application. In addition to corrosion-resisting properties and high melting point, the metal has an ability to withstand unusual amounts of cold working. It affords some striking demonstrations of block movement during plastic flow. Strength and Ductility of Tantalum Since there is no good way of defining working properties numerically, illustrations will be used. It is possible to roll a bar of pure tantalum 0.4 in. thick to sheet 0.001 in. thick, without heating or annealing. The sheet produced will be sound and may be bent upon itself at right angles to the direction of rolling. Longitudinally the sheet will be somewhat brittle. A disk of annealed metal may be cupped and drawn to the form of a capsule 3/16 in. dia. by 146 1? in. long. If carefully handled this capsule can be further deformed by drawing to a tube having an outside diameter of 0.050 in. Disks of tantalum may be spun into tubes of 39 in. dia. and 1½ in. long. In the form of rod, reductions may be made from 0.4 in. to 0.001 dia. In the latter process, it is necessary to heat the wire four or five times to 500" C., at intervals between 0.040 and 0.001 in. Although the melting point of tantalum is 2850" C., these heatings at 500" C. are sufficient to distinctly anneal it. Published figures on the strength and ductility of tantalum are not particularly accurate. This is due to the fact that these properties vary widely, depending on the extent to which the metal is contaminated by gas. There are no sharp critical points in these changes with gas content; samples of metal will vary from a springy or actually brittle condition to one of leadlike softness. Samples that have had a prolonged heating at high temperatures in a good vacuum, under conditions such as would be provided in vacuum-tube experimentation, will yield a product of about the hardness of annealed copper. The usual commercial metal will have the hardness of annealed mild steel.

Jan 1, 1930

By F. F. Frick, Frederick Laist

In a leaching process, having obtained the copper in solution, the choice of the precipitation method is influenced by the following factors: 1. Availability of precipitant. 2. Adaptability to the leaching process. 3. Final product desired. 4. Regeneration of leaching solutions. 5. Fouling of solutions. There are three general classes of precipitation methods: 1. The use of iron, scrap or sponge. 2. Electrolytic deposition. 3. The use of some gas or reagent by which the copper is obtained, usually in the form of an intermediate precipitate which requires further treatment. For example, the precipitation of, the copper as Cu2Cl2 from chloride solutions; with SO2 gas. The use of iron is adapted to almost any process. It has the great advantage of extreme simplicity, and the recovery of the copper and any values present in a highly concentrated, easily treatable form. The disadvantages are the cost in isolated places, the uncertainty of the scrap-iron market, and the fouling of the leaching solutions. The latter is a serious factor, when a reagent such as salt is used in them, which makes necessary their re-use. Where applicable, electrolytic deposition is very attractive. The copper is obtained in a form directly marketable, there is a regeneration of acid and no fouling of solutions. Unfortunately, chloride solutions do not lend themselves to electrolysis. An entirely satisfactory anode material has not yet been discovered, although magnetite, apart from being rather brittle, seems to answer the requirements fairly well. The use of a method of the. third class is involved in many special

Jan 1, 1915

By H. D. Hoskold

It was not for the purpose of asserting any superior knowledge or authority, but simply of clearing up, in greater detail, some points casually mentioned in Mr. Scott's able paper, that the writer entered, some two years ago, into the discussion which that paper initiated. In such matters there is always room for differences of judgment, as well as for additional data, which may modify or complete the conclusions even of the best authorities. Those who are immersed in the duties of practical administration or work in the field, and who, being remote from the great scientific national libraries, are obliged to rely on their private collections, and to supplement them by their recollections of earlier studies, labor under special disadvantages in such a discussion; and it must be to the scientific and engineering world a matter for gratitude that Mr. Lyman has been willing to give the benefit of his advantages in this respect. Mr. Lyman would, however, doubtless at once disclaim the conclusion that his masterly summary constitutes " the last word " on this subject, and welcome further evidence, comment and criticism, such as the various contributors may continue to offer. This, therefore, is the motive, and must be the excuse, of the introduction by the writer of the following observations. The Miners' Dial.—Many years since, the writer employed a miners' dial, older in type than Fig. 12,* but without any attached spirit-level, made by Thomas Jones, a pupil of the great Ramsden. Jones was one of the old London makers and opticians, and enjoyed great reputation for accuracy in the con-

Jan 1, 1902

By Guillermo V. Borquez

INTRODUCTION The basic factors that influence the selection of a mining method are the geometry of the ore deposit and the strength of the ore and surrounding rock. These factors usually determine the ore recovery and dilution of the deposit under analysis. For the purpose of this paper we will consider a generalized case of a block caving system and the sequence of the analysis needed to optimize ore recovery. The analysis presented is intended for the preliminary planning stage. The critical factors involved in the caving process are identified and the methods for evaluating the suitability of a particular deposit to the caving method of mining are outlined. The mine design is approached by identifying the two most important, dimensions: the size and spacing of the draw points. These dimensions are estimated from a simulation model which takes into account the ore recovery, the incremental value of the ore recovered, and the safety conditions of the operations. The model estimates the number of draw points required to extract efficiently and safely the broken ore from the caving area. This number is found in the range where the net incremental value of the ore is maximized and the probability of pillar failure does not exceed the limit which is acceptable for a safe mining operation. A mining method and its design are in a continuous process of optimization. This process is unique for each deposit because of the many parameters involved; therefore, a back analysis of the operations should be performed when possible. These analyses will indicate if the ore body responds in a predictable manner to the parameters contained in the geological, fragmentation, and draw point models. SELECTION OF ALTERNATIVE MINING METHODS The selection of a mining method best suited to define the minable ore reserves of a given deposit involves consideration of the geometry of the ore deposit and the strength of the ore and surrounding rock. These two factors are usually sufficient to determine the ore recovery and dilution of the deposit. After analyzing the geological reserves and defining the limits of the deposit, either an open pit or an underground mining method can be selected to define the minable ore reserves. The sequence of steps to follow in the selection of a mining method is presented in Figure I. From an economic point of view, the strip- ping ratio is the determining factor for the selection between an underground or open pit method. In turn, the stripping ratio is a function of the grade distribution and con- figuration of the ore body. In order to obtain a preliminary estimation of the stripping ratio, a parametric analysis could be applied, such as the approach used by Professor E. P. Pfleider (1972) and summarized in Table 1.

Jan 1, 1981

By A. M. Kivari

OPERATIONS at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials Closed-circuit grinding, classification, hydroseparation, flotation, agitation, and thickening are familiar terms at this cement plant These methods make it possible to process refractory limestone into suitable materials for the manufacture of modern cements Construction of the plant, haying originally a design capacity of 7000 bbl of cement per clay, was started in June 1939, and the first clinker was ground on the following Christmas Day At present the capacity is about 12,000 bbl of finished cement per 24 hr , most of the production being low-heat cement † About 3130 tons of limestone, 620 tons of clay and 100 tons of gypsum are required daily for this output Occasionally iron oxide is added to the clay to obtain the desired composition This, together with the gypsum, is purchased from outside sources Up to the present time, the corporation has produced low-heat, normal, moderate¬ heat, moderate-sulphate-resisting, high-early-strength, oil-well, modified-oil-well, and plastic cements Most of the present production is for Shasta Dam, near Redding, Calif , the told demand being 5,800,000 bbl of cement Following are sonic of the cement requirements of the Shasta D [im] specifications [ ] The average specific surface in the bin s sampled shill be not less Ulan 1800 sq cm per gram and no individual sample less thin 1600 sq centimeters Compressive strength The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2 75 parts fine testing sand, by weight, shall be equal to or greater thin the following

Jan 1, 1941

By Oswald J. Heinrich

The deposit of rock salt along the shores of Lake Huron, in Canada, has been brought before the public during the last six months, in consequence of the developments made by the diamond drill at Goderich. It is likely to be of more than common interest in the future, since now actual operations have been commenced to exploit the deposit and work it by regular mining. The methods of mining rock salt being but little known in this country, it may be of interest to make a few general remarks in regard to them before entering, upon the description of this new mining enterprise. According to the conditions under which salt is .found in nature, various methods have been resorted to, in course of time, to make it available for the human race. They consist in: A. Natural or solar evaporation. B. Artificial evaporation, either exclusively or in connection with the former. C. Mining the rock salt in its natural state, and converting it to a marketable product, if need be, by simply pulverizing it. Without going into the details of the various methods of making salt available in an economical point of view, dependent on its degree of pority, or on various local influences, we cannot refrain from alluding to the general principles which influence the mining and manufacturing of salt in countries where they have been carried on for hundreds of years. ECONOMICAL CONDITIONS FOR SUCCESS. Salt being one of the articles of prime necessity, and one universally distributed throughout nature, it must always be sold at a comparatively low price. It would even be quoted in the market at prices far below those now ruling, if it were not for the high duties generally imposed upon it, for purposes of state revenues. But looking closer into the subject, it will be found that this duty is probably one of the least oppressive, although in some countries it exceeds sixfold the cost of profitable production. To produce the article at the lowest possible cost requires, therefore, a

Jan 1, 1879

By Dara P. Antia, Morris Cohen, Frank S. Gardner

THERE is a conspicuous lack of information in the literature on the precise role played by residual quantities of austenite in heat-treated steels. While retained austenite may be expected to have significant effects on such important properties as the impact resistance of tools and carburized parts and the dimensional stability of dies and gauges, attempts to study these problems systematically have suffered from the absence of a reliable technique for ascertaining absolute amounts of austenite. With such a technique, not only could the relation between residual austenite and service behavior be investigated, but the chemical and heat-treatment factors that control the quantity of the austenite could also be established. Thus, the retained austenite content could then be regulated in accordance with the results desired. The presence of retained austenite may be inferred by observing the changes in properties (hardness, specific volume, electrical resistance, etc.) due to its decomposition on subatmospheric cooling1 or on tempering,2 but these indirect measurements are not readily translated into percentages of austenite. Quantitative determinations have been achieved in special cases by means of dilatometric3 and magnetic4,5 measurements; but the former procedure requires that observations be conducted during the hardening and involves difficult calibrations that limit its applicability, while the magnetic procedure is very sensitive to extraneous influences and depends upon assumptions that can only be considered as approximate in an absolute sense. Furthermore, both the dilatometric and magnetic effects are volume properties, and cannot be conveniently utilized to explore variations in retained austenite from point to point in a specimen. Some microstructures lend themselves to accurate evaluation of retained austenite contents by metallographic methods,3 but such instances are not too common, and at best, the procedure is tedious. The characteristic X-ray diffraction lines of austenite permit positive identification of its presence; and in the present paper the intensities of these lines, or the corresponding densities* on photographic film, are employed to measure the amount of the retained austenite. In order to cancel the effect of uncontrollable variations in the X-ray exposure and film-development conditions, a standard reference line is superimposed on each film by maintaining a foil of aluminum in the path of the incident X-ray beam during the entire exposure. With different samples of steel and the same foil, the ratio of the density of some one austenite line to the density of

Jan 1, 1943

By C. G. Dunn, J. L. Walter

The c/laracterzstics of cube-oriented nuclei ard other matrix grains that are associated with secondary, recrystallization to the cube texture in high-purity silicon iron were investigated by me-tallographic and X-ray methods. The results show that the structure consists of relatively perfect grains of average diameter between one and two times the sheet thickness ad that the texture has a moderately strong (110) [001] component and a weak (100) [001] component. The results also indicate that matrix stability results from the two-dimensional nuture of the graitzs and that cube-orzented nuclei are neither more Perfect nor larger grains than other matrix grains but have a preferred [001] direction in the rolling direction and have a more effective driving force for growth than other grains because of a low (100) surface energy. THE structures and textures of fine-grained rnatrices determine to a large extent the kinds of secondary recrystallization textures that form on annealing. The understanding of secondary recrystallization processes therefore depends on adequate information about the initial matrices. Matrices usually have three characteristics: 1) they consist of fine-grained primary recrystallization structures, 2) the fine-grained structures are stable toward normal grain growth, and 3) they contain secondary recrystallization nuclei. Stability toward normal grain growth may be due to either a strong single orientation texture (texture inhibition)' or a dispersed second phase (dispersed phase inhibition).2"4 If normal grain growth is not inhibited by either of these two factors, it nevertheless stops when the average grain size is between one and two times the sheet thick- ness.5 This thickness effect satisfies one of the characteristics of a matrix for secondary recrystallization. Its importance in the development of the cube texture in high-purity silicon iron by secondary recrystallization was pointed out by the authors in a recent paper on tertiary recrystallization7 and will be discussed further in the present paper. Assmus, Detert, and he8 have provided some information on a matrix for secondary recrystallization to the cube texture in silicon iron. They found a (110)[001] or Goss texture with enough spread about the rolling direction to include a small amount of the (100)[00l] orientation. The distribution of the [00l] directions was strongest parallel to the rolling direction for both (100) primaries and cube secondaries. These authors found no correlation between size of a matrix grain and orientation and concluded that some property other than size must be the distinguishing characteristic of the cube-oriented nucleus. No consideration was given, it

Jan 1, 1961

By E. L. Dougherty, J. W. Sheldon

A numerical method for computing the dynamical behavior of fluid- fluid interfaces is described. Results of studies made to assess the accuracy and economy of the method on a computer are reported. It is concluded that it is practical to obtain digital computer solutions for fluid- fluid interface problems with two space dimensions. PROBLEM DEFINITION We consider two-dimensional flow in a rectangle as shown in Fig. 1, where a fluid-fluid interface divides the rectangle into two regions. The pressure is specified along the lower boundary (the injection boundary) and upper boundary (the withdrawal boundary). There is to be no flow of fluid across the side boundaries, which are walls of symmetry for the flow, and px = 0 along these boundaries. The fluids are incompressible, the absolute permeability and porosity is constant, and each fluid has its own constant mobility. Thus, the pressure satisfies Laplace's equation in each region. Across the interface, pressure is continuous and the normal component of fluid flux is 1. These conditions are shown in Fig. 1. The velocity of a point on the interface in the direction of the normal from Fluid 1 into Fluid 2 is U,/ Q, where Un is the normal component of volumetric flux at the point on the interface, i.e., For brevity, we call the problem defined above "Problem A". Problem A is a simple example of a dynamical fluid-fluid interface problem. However, the same numerical methods which we use to solve Problem A can be extended to the solution of a large number of fluid-fluid interface problems which are mathematical models for various oil recovery processes,l hence our interest in Problem A. We define the interface by prescribing the x, y coordinates of a finite set of points. These points are called "interface mesh points" and are illustrated by triangles or asterisks in the figures. Fig. 2 is a procedural (flow) chart displaying the main steps in the solution. We comment briefly on some of these steps in this section and then give further details in subsequent sections. For mobility ratio greater than one it is well known that Problem A is unstable.*2 Small amplitude,

Jan 1, 1965

By C. W. Stratford

[During the last few years, the necessity for development work has been generally recognized by executives throughout the oil industry, resulting in greatly accelerated progress and the adoption of many noteworthy improvements in refining methods and equipment. Several years ago, the Associated Oil Co. decided to improve distillation methods with the object of reducing refining costs. This extremely interesting work was entrusted to the writer, and W. S. James, now Chief of Research for Studebaker Corpn. of America, was selected as the principal collaborator. The latter contributed much during his two years with the Associated Oil Co., to the development work that has followed. The writer extends to the Associated Oil Co. his appreciation for permission to disclose the details of distilling equipment. In petroleum refining the principal requisites of good economics are the separation of high-priced distillates from those of lower price; maxi-mum yield of any desired distillate; lowest capital investment in refining equipment; lowest cost of operation and maintenance, and the best adaptability and flexibility of the same refinery equipment for handling crudes of widely varying characteristics. The first two items mentioned, separation and yields of distillates are determined by efficiency of fractionating equipment,. Discussion in this paper is chiefly concerned with oil-heating equipment, combustion and furl economy. It has long been well known that velocity plays a very important part in all heat transfer systems. Any betterment in specific transfer. rates in such systems must. always involve velocity. Realizing this fact, IV decided to adopt as a basic principle, the employment of energy to impart velocity required for high transfer rates through a heating diaphragm, and our method of modernizing obsolete shell stills is founded on this principle. Mechanical energy is usually cheap and its rational rspcntliture is returned in the form of greatly increased heat transfer rates, on both oil and gas sides of the sheet. Certainly there is nothing new in this principle, the only novelty being that of our peculiar method of application On the oil side (Fig. I) use is made of a centrifugal pump to jet the oil against the heated sheet thereby creating a high velocity sheet flow over the entire fired area. Such a pump is one of the most efficient machines, so far developed, for moving fluids. 'I'he oil, under pressure impinging

Jan 1, 1928