Search Documents

By D Craw, J Youngson

Recent exploration for mesothermal gold deposits in the Otago Schist has focussed largely on extensions of, or analogies to, the reverse fault-hosted Hyde-Macraes Shear Zone deposit. Abundant normal fault-hosted mesothermal and epithermal vein deposits in the Otago Schist have attracted less attention, largely because they have limited lateral extent and steeper dips. Northwest-striking normal fault-hosted vein sets near Barewood and Hindon in east Otago crosscut schist foliation on the Barewood-Hindon plateau at a high angle along a combined strike length in excess of 20 kilometres. The trend of the vein sets is not linear, but rather contains several right lateral steps. Almost all veins dip steeply to the northeast. Angular discordance between schist foliation and the plateau surface along the trend increases from near zero at the northwest end of the veins to about 30¦ at the southeast end. Crude formation depth estimates decrease from about 7.5 km at the Barewood end of the zone to

Jan 1, 2002

Support design in jointed or blocky rock masses is often approached by the use of either 'rules of thumb', rock mass classification systems such as the Q-system (Barton, Lien and Lunde, 1974) or RMR (Bieniawski, 1973) or conventional wedge analysis. Generally, this requires that a number of key simplifying assumptions are made and the support system is designed to cater for either a mean, most likely, or worst case scenario depending on the risk tolerance. The design block size is often a major uncertainty and often a worst case block size based on excavation span is used. Thompson and Windsor (2007) state that it is inappropriate to base support designs on the excavation size as these size blocks rarely occur if discontinuity trace lengths are considered. Probabilistic keyblock methods can be used to determine the most likely design block sizes. A methodology is presented whereby JBlock software (Estherhuizen, 1996) is used to estimate potential block sizes as part of the support design process. Using information such as the spacing, orientation and length of discontinuities, it is possible to simulate blocks in the walls of an excavation (Esterhuizen and Streuders, 1998). Keyblock analysis methods (Goodman and Shi, 1985) are used to evaluate whether blocks are removable and whether the chosen support will be sufficient to ensure stability. Data from two mines is used to demonstrate how probabilistic keyblock analyses can be used in support design. Discontinuity data was used to generate 10 000 removable blocks and the design block size statistics were determined. For one mine this information was used to scale blocks in a conventional. Unwedge analysis whilst for the other mine, the point estimate method (Harr, 1987) was applied. The choice of appropriate design acceptance criteria in terms of factor of safety and probability of failure is also considered.

Nov 25, 2010

By D N. B Skinner, R L. Brathwaite, M S. Rattenbury

The Institute of Geological and Nuclear Sciences is undertaking a mineral resource assessment study of the Coromandel region, due for completion in July 2000. A key part of the study is the assembly of a geographic information system (GIS), a computerised tool for layering, analysing and presenting spatial information. The GIS is being assembled with ArcInfo/ArcView software and to date includes layers for a digital terrain model, an aeromagnetic map (open file mining company data), a geological map (from the QMAP project), areas of hydrothermal alteration, locations of mineral deposits (GERM database), stream sediment geochemical analyses (REGCHEM database), and a lineament map derived from satellite remote sensing data.

Jan 1, 1999

The Effect of Bulk Iron Concentration on the Copper Activation of Sphalerite at pH 9

Sep 13, 2010

By P Fullagar

Automated multi-sensor core loggers (MSCL) measure petrophysical properties of diamond drill cores, including gamma density, P-wave velocity, electrical conductivity and magnetic susceptibility. A Geotek MSCL system has been used to record petrophysical data on archival drill core from Cadia East Au-Cu porphyry deposit, New South Wales, Australia, for correlation with metallurgical parameters. P-wave modulus, calculated from density and P-wave velocity, exhibits a correlation with small-scale crushability (A*b) test results, and hence offers a means for æcontinuousÆ characterisation of ore crushability at Cadia East. Magnetic susceptibility has proved to be a good indicator of alteration styles, and is a possible indicator of crushability.

Jan 1, 2009

By French D

In presenting this paper may I preface my remarks by recognizing the presence here to-day of the many delegates from the overseas mining communities throughout the world. That is to say - those delegates not representative of Companies resident in Australia. This does not mean that my comments following are directed solely to the Australian exporter - far from it. The Company which I represent is internationally based. The experiences we have had in dealing and negotiating with our good friends the mineral cargo shippers vary very little in any operational area. However for the purposes of this exercise this address is based on some of our experiences within the Australian trade scene with the emphasis on the fact that we believe it has application to all trading areas.

Jan 1, 1989

In referring to two subjects of interest to the Members of this Australasian Institute of Mining Engineers, I would at the outset desire to express our gratification that to-day we are able to welcome as now united with ourselves, those members who until recently constituted the New Zealand Institute. It is hoped that the amalgamation so amicably arranged may be productive of the best results to all concerned, incorporated as this combination has been at the moment of the fulfilment of that greater political union, the Australian Commonwealth.Since last Annual Meeting held in Brisbane, we have come under the same roof as the Chamber of Mines of Victoria, and we entertain the hope that as that Chamber and this Institute possess so many interests in common in the encouragement and advancement of mining and metallurgical progress in these colonies, that much mutual benefit will ensue. There are many directions in which each body can assist the other, and I trust that a friendly co-operation will be maintained.It is gratifying to feel that in all the colonies a distinct movement is being made to increase the facilities for education in Mining and Metallurgy but if I may refer to our colony of Victoria in particular, we have to express the profound regret that in the means of education in the higher branches, we occupy an inferior position, and it is quite certain that we will continue to do so unless the Government is prepared to subordinate provincial considerations to the weightier.

Jan 1, 1901

A Study on Main and Interaction Effects of Operating Variables of Column Flotation

Sep 13, 2010

About twelve months ago, owing to the increasing quantity of stone and dirt being drawn frQm the Victorian State Coal Mine due to the large amount of dead work below ground, cutting, faults, etc, and to the increasing quan#ty of banded coal beingworked, the writer was forced to consider the question of economy in handling the spoil at the surface. The method in operation at the time was to run out level dumps fro,m the, tipping floor of the heapstead, or brace, and to tip most of the skips of stone in tipplers at the ends of the dumps, the remainder of the skips being side-tipped to widen the dumps.The method, whilst quite satisfactory for dealing with a few skips of stone, was found to be costly as the dumps extended, and the number of skips to be dealt with increased from 300. to 400 per day of two shifts;. therefore, in order to expedite thework and cheapen its cost, the writer devised an improved method which may be qescribed as follows :-(1) The stone is tipped into a hopper car which holds about 10 skips(2) The hopper car is hauled up an inclined dump by means of an electric winch.(3) The spoil is dumped from the car forwards or to either side, as required.(4) The car is returned to the starting point for a further load.Plate I Fig. 1 gives an idea of the construction of the hopper car. In the illustration the car is in position for tipping to one side. The body of the car is supported on a ball race on the under carriage, and it can be swung round to tip in any required direction. The bottom of the hopper is extended to form a 4 ft. lip...

Jan 1, 1918

By Edwards A. B

A suite of specimens from the newly developed Black Star copper ore body at Mount Isa was made available for mineragraphic study by the Mount Isa Mines, Ltd. The specimens were selected as representative of the different phases of mineralisation found in the ore body, rather than with a view to furnishing a complete cross-section of it; and the examination has been carried out with a view to ascertaining (1) the nature, extent and association of the arsenic, antimony and possibly bismuth, minerals in the ore, (2) the mode of occurrence of silver in the ore, and (3) whether galena and sphalerite occur in minute forms well below the sIzes readily observed in hand specimens.Analyses of the January to June, 1944, mill head composites show that the proportions of the elements Ag, As, Sb and Bi in the ore are as follows:Ag 0.000013 = 0.35 oz./tonAs 0.024Sb 0:002Bi 0.0005The copper content of the mill heads ranges from 3.5% to 4.75%, the lead content from 0.03% to 0.08,% and the zinc content from 0.09% to 0.23%.MINERAL COMPOSITIONThe specimens range from massive sulphide ore, consisting of areas of chalcopyrite, pyrrhotite, and rarely sphalerite, from 1 to 3 cm. across, to fragments of extremely finely banded pyritic shale in which no minerals other than pyrite are visible. The gangue associated with the massive sulphides is chiefly dolomite, and sometimes white quartz. The pyritic shale fragments show evidence of shearing and faulting on a micro-scale, the fractures sometimes being filled with sulphides and vein minerals.The ore minerals found in the polished sections are pyrite, arsenopyrite, marcasite, sphalerite, chalcopyrite, valleriite, chalcostibite, galena, dyscrasite, jamesonite, magnetite, gold, graphite and rutile.Pyrite (FeS2)Pyrite occurs chiefly in two forms according to whether deposition took place along the bedding planes or along the intersecting faults and fractures. Deposition of pyrite along the bedding planes of dense, thinly banded shales ha,s produced a metasomatically altered shale in which the pyritic bands are from 0.02 to 0.03 mm. wide, and alternate with bands...

Jan 1, 1945

On the Hauraki goldfields, within the limits of Cape Colville Peninsula, the Paheozoic rocks are confined to the district north of a line drawn from Mercury Bay on the east coast to Rocky Point on the shore of the Frith of Thames. South of Kennedy's Bay they are developed on the east coast only at Kuaotunu, at which place gold mining is carried on in sandstones and slates of this age. Between Tapu Creek and Coromandel there is, along and adjacent to the shore of the gulf, a very considerable development of PaJreozoic and in part of Trias rocks, and between the Tiki Stream and the northern end of Tokatea Hill, along the western slope of the main range, lies the special area of the Palreozoic or carboniferous rocks that have more particularly to be dealt with in this paper. The same formation has a large devolpment between Cabbage Bay and the northern slopes of Moehau, and appears to the water marge on both sides of this part of the peninsula.In this part they are of special interest as having, on the west spur of Moehau, a considerable variety of dyke rocks intruded into the sedimentaries, the interest in which is increased by the fact that these dykes theIllselves are of Palreozoic age and correspond to the dykes that are so' abundant in the Tokatea-Tiki area. It is this Tokatea-Tiki area as a goldfield, and its rocks as distinguished from later volcanic' products' on other parts 'of the peninsula...

Jan 1, 1903

The objectives of this paper are to introduce the International Code of Practice for Risk Management of Tunnel Works and to illustrate to the participants of the 13th Australian Tunnelling Conference 2008 how the insurance industry would like to see the future of tunnelling insurance. Tunnel construction projects have suffered large losses over the years as can be shown from various loss examples and a list of major losses over the last ten to 15 years. Since the consequences of insufficient risk control had to be borne by insurers, these losses have heightened the need for improved and adequate risk management measures so that insurance cover can also in future be provided for this hazardous industry sector. Observations are made as regards to the prevailing trends in the tunnelling industry, which contribute to the increase in risk and have adverse consequences for the insurance industry. To find a solution to this dilemma various options are examined with the suggestion of a Joint Code of Practice for Tunnel Works being agreed by all stakeholders, which would become essential to secure future insurance protection for such project work. The British Tunnelling Society has, in cooperation with the Association of British Insurers, developed such a code, which the International Tunnelling Insurance Group has now adopted for global application in international markets. The content and concept of this code is explained to establish a framework of understanding and applied risk management principles for tunnel works. This initiative also has the support of the International Tunnelling Association and the International Association of Engineering Insurers. The international application of this new code is demonstrated with a few examples, which also includes Australian projects. It is the aim that this code forms in future part of the insurance coverage for tunnelling works in order to put this risk segment on a more sustainable basis. For that reason the insurance industry is seeking the support of all stakeholders of tunnelling construction projects.

Jan 1, 2008

The construction of the pipeline was completed in June 1956 and the line placed into operation in December 1956, ie. it has now been in continuous operation for approximately three years under an operating pressure of up to 350 lb. p.s.i.In reviewing the operating experiences of the line we must consider three major factors, which are:(a) The effectiveness to date of the protective methods for prevention of corrosion of the pipeline, ie. the preservation of the asset.(b) The maintenance of the line in regard to interference as to its stability which could be occasioned by erosion of the line, land-slides, accidental interference by the public, or construction authorities, etc.(c) The operating techniques employed.PROTECTIVE METHODS OF THE PIPELINESo to permit a clearer appreciation of the effectiveness of the protection of the! steel pipe against corrosion, I will briefly describe the methods used in the construction of the line.The line, which is 18 in. O.D. by %6 in. thickness steel pipe, is located approximately It miles south of the main Melbourne/Gippsland electrified railway.The steel from which the pipe was manufactured conforms to ASA.A33-1937 with the following modifications.Minimum elongation on a 2 in. test specimen...

Jan 1, 1960

A way back in 1851-2 an army of diggers had commenced the conquest, of the now famous goldfields of Australasia. At that time, and in the Colony of Victoria, more that 10,000 were camped on and around the slopes of the silurian ridges over which Ballarat East h'as been built. A wonderfully rich golden harvest was soon gathered from the alluvial found high on these slopes, and from runs (or gutters) which got their rise on them, and were traced down gullies into a broad valley. In due course it was ascertained that the valley carried a main gutter which represented the unity of the higher ones, and further explorations proved this gutter to have a westerly and then a southerly trend toward and under a basaltic plateau, on the top ofwhich Ballarat West and Sebastopol now stand. In the records of alluvial gold mining all the world over the Ballarat field can be classed amongst the richest. Gold in pieces the size of beans, in, stringy filigree bits, in dust and in solid lumps (the largest of which weighed more than 2,200 ozs.), was obtained in the comparatively shallow ground on the slopes; and speaking generally, great and uniform richness was met with along a belt of country on which, in a north and south line, the present quartz mines of Ballarat East are at work. It was noticed by the diggers that when the gutters crossed the upturned edges of the ,strata, the gold deposits in them were patchy, and that when they trended north and south on this beltthey carried rich deposits for longer distances. In time it was also noticf!d that a class of stringy, irregular shaped quartz occurrences, in a bottom of soft slates, in the, immediate vicinity of tpe g)ltter, meant greater richness, and (in the aIluvial) on the higher ground slabs of quartz would now and then be met with, in which strings and spongy masses of gold were found. As the shallow alluvial became worked out the diggers turned their attention to the quartz occurrences, and, now and again the striking of a flat make of a very golden nature would cause quite a stir in the local mining world.

By J Knoblauch, D, P J. J Strobos, C Foggo

The Sally Malay Project is located 120 km north of Halls Creek in the eastern Kimberley region. Since commissioning, ongoing improvements on the plant have resulted in recoveries now greatly exceeding the initial design targets. The continual optimisation endeavours of the Sally Malay metallurgy department included an automation project that was done in close collaboration with Mintek. In this team effort, several problem areas were addressed and the FloatStar advance control system was successfully commissioned to stabilise and optimise the flotation circuit. The remote location of the Kimberley Nickel Mines operation, fly-in, fly-out roster and the current mining boom makes the acquisition of experienced flotation staff difficult. The implementation of an automated flotation control system reduces this burden and contributes to the training of inexperienced staff. This paper illustrates not only the process control improvements achieved as a result of the installation of the FloatStarÖ advanced control system, but also how it has assisted operational personnel with their understanding of the process.

Jan 1, 2006

By K Prendergast, P Dale, I Taylor, A J. Vigar, B Lueck

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Kainantu Project is located within the New Guinea Thrust Belt in northern Papua New Guinea. The area has a long history of exploration and production, with the discovery of alluvial gold in 1928 followed by the discovery of vein deposits of gold and copper at Kora in the 1950s and the current Irumafimpa vein gold mine. Current resources on the Kora-Irumafimpa Vein System (KIVS) stand at 1.5 Moz Au, 5 Moz Ag and 217 Mlb Cu.Mineralisation in the region includes gold, silver and copper associated with mid-Miocene age mafic to felsic intrusions. The KIVS occupies a broad north-west-trending mineralised zone more than 2.5 km long and 200 m wide, with the Kora, Eutompi and Irumafimpa veins on the western side and the Judd and Upper Kora veins on the eastern side. Economic mineralisation occurs in two closely related events occupying the same strongly structurally controlled shearing (quartz-Au-telluride veins and sulfide Au-Cu-Ag veins with free Au) and is best described as a significant intrusion-related event with both epithermal and mesothermal facets that does not appear directly related to known porphyry Cu-Au systems as seen at the surface. Significant wolframite is associated with vein quartz of a slightly older age but also occupies the same shear system.The KIVS occurs within a larger mineralised area of approximately 5 × 5 km. It has complex multiphase intrusions, breccias and diatremes that are only partly delineated by drilling and comprises multiple occurrences of Au-bearing veins and porphyry Cu-Au mineralisation. The area is considered to have high potential for extending the current resources and is being actively explored. The proposed recommencement of mining activities recognises the complexity of the KIVS and later disruptive faulting and will require tighter grade control systems, targeted mining techniques and a gravity circuit to maximise free Au recovery.CITATION:Vigar, A J, Lueck, B, Taylor, I, Prendergast, K and Dale, P, 2015. Kainantu gold-copper system, Papua New Guinea, in Proceedings PACRIM 2015 Congress, pp 601–606 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

It is the purpose of this paper to produce some evidence on the accuracy to be expected from normal assay procedure using the usual first class equipment, and to examine the effect that many assaying inaccuracies have on reported metallurgical recoveries.Generally speaking, the evaluation of the gold content of a mineral ore sample by the fire assay method is a relatively simple process.A weighed quantity of finely ground ore is fused with suitable fiuxes including litharge and a reducing agent to give a button of lead and a quantity of slag. The shower of lead produced by the reduction of the added litharge collects the gold and silver present in the ore, concentrating the values into the lead button.The button of lead, after separation from the slag, is, on heating in an absorbent cupel in a current of air, reoxidised to litharge and absorbed into the cupel leaving a gold and silver bead in the cupel. This bead' is heated in a solution of nitric acid to dissolve the silver, leaving the gold undissolved to be dried and weighed. Knowing the original weight of the ore and the weight of the gold prill the value of the ore is easily calculated.Summarising1. Fusion Process.-Ore plus fiuxes give a slag plus lead button.2. Cupellation Process.-Lead button is re-oxidised to litharge leaving a gold and silver bead.

Jan 1, 1952

Amongst representative men directing alluvial mining of erations in Victoria, some difference of opinion exists as to the best system of working the deep leads. The developmental operations of shaft-sinding, extending a reef drive, partially watering and rising up into the wash dirt are practically the same on all fields but subsequent mining is continued either on the Chiltern and Rulberglen or Ballarat systems, the latter being referred to by the Chiltern and Rutherglen miners as the "down country" system. In the former, the leading wash and cross drives are lept from 300 to 500 feet ahead of the reef drive, and in the latter the reverse method keeping the reef drive well ahead of all wash workingsis adopted.In the majority of alluvial mines in the southern and western fields, the initial work of defining the course of the lead is costly, owing to the thick superincumbent layers of hard basalt, to bore which costs from 9/- to 15/· per foot. Unfortunately large sums of money have been wasted in this work, owing to a want of care and knowledge in the selection of bore sites, and improper recording of the strata pierced, thus handicapping alluvial mining and bringing boring operations...

Jan 1, 1902

By C J. Kruger, E le Roux

Anglo American Platinum has adopted a strategy of Best Practice Principles (BPP) for sampling, mass measurement, analysis and metal accounting for more than a decade now. When new plants are designed, the most suitable sampling equipment and sampling protocols are implemented and material flows and plant layouts are designed around sampling strategies. A few years ago, a crushing plant for a high-grade matte stream was commissioned.The design called for the high-grade material to be crushed to 95 per cent passing 2 mm and the design allowed for a single cutter primary Vezin sampler, increments taken from a gravity flowing stream at regular intervals, whilst filling a tanker for the pneumatic offload at our base metal refinery. This was a single point of sampling and analysis that would measure the wanted output from our smelting complex and the input to our refineries. In addition, the design incorporated the functionality to collect increments in an ‘interleaved’ fashion from the Vezin sampler for internal precision checks.The metal accounting strategy for Anglo Platinum is the ongoing measurement of all inputs, outputs and stock levels for all our operations for platinum group metal (PGM) and base metal (BM) content. Included are yearly stocktakes, usually done on 1 February every year, across the smelters and refineries (at least the base metal refinery). A trend was developing in the accounting period immediately following the introduction of the new crushing and sampling facility, whereby the absolute difference between the physical stock and theoretical stock (PGMs predominantly) increased for the two respective sites on an ongoing basis. The smelter (sender) showed an increase in physical stock compared to the theoretical stock and the base metal refinery (receiver) showed that their theoretical stock increased against their physical stock. Because of this anomaly, an additional stocktake was held in September for the period in question and it was confirmed through the physical stock measurement results, that the PGM accounting problem was indeed pointing towards the evaluation of the high-grade matte stream.This paper showcases parts of the process that took place to explain the poor accountabilities for the respective sites. Previous results from the sampler ratification process (of the interleaved sampling design) were analysed again, a physical inspection was carried out on the sampling system again and the sampler performance was monitored (quality control parameters) for the period.From these investigations, it was found that airflows present inside the Vezin introduced the sampling bias and a change in sampling protocol was introduced as well as physical changes to the sampling equipment were made to eliminate the airflow and thus the bias conditions significantly. The accounting period which followed, after a phased upgrading process, showed that the accounting between our smelter and base metal refinery had been restored to within statistical limits (difference between physical and theoretical stock below five per cent relative to theoretical stock).CITATION:Kruger, C J and le Roux, E, 2017. Pitfalls in Vezin sampling for finely crushed materials, in Proceedings Eighth World Conference on Sampling and Blending , pp 151–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By G J. Corbett, T M. Leach

A continued exploration programme has further defined the geology of the Tolukuma vein system, verified the resource indicated by Newmont, and identified potential for additional mineralisation. The resource at Tolukuma Hill, designated as zone C, is a mine recoverable 432,000 t at 18.1 g/t Au & 46 g/t Ag. Mining will be by a combination of open pit and underground at a rate of 100,000 t per annum. Processing will be by SAG mill, gravity circuit and CIL plant. A diatreme breccia, localised at an intersection of structures and a relationship of gold to base metal sulphides, are indicative of a strong porphyry association. Typical epithermal features such as crustiform banded quartz and quartz pseudomorphing platy calcite are also present and locally contain lesser gold mineralisation. Pre-existing dilatant structures have acted as a host to the ore fluids, resulting in the formation of the semi-continuous Tolukuma-Gulbadi veins over a 1100 m strike. A fluid flow model suggests that mineralizing fluids were sourced from a diatreme margin and migrated laterally along dilatant structures. Bonanza gold grades are interpreted to be derived through fluid quenching in the flexure between a hanging wall split, which hosts much of the Tolukuma Hill resource, and the feeder graben structure. Thus, the relationship between the pre-mineral structural geometry and fluid upflow at the margins of a diatreme breccia, controls the ore setting.

Jan 1, 1995