Search Documents

By P Christen

The Ernest Henry Copper gold mine situated in North West Queensland, Australia, is owned and operated by Xstrata Copper. Currently the open pit produces 11 Mtpa of ore. With open pit mining ceasing in mid 2011 development has begun on an underground sublevel cave mine to extend the life of the operation by another 12 years. When completed the open pit will be 530 m deep and 1.5 km in diameter. The orebody dips at approximately 45° and has been outlined a further 450 m below the base of the pit. This provides some challenges for the Ernest Henry underground mine which is designed to initially truck development and production ore from the end of the pit until a hoisting shaft is commissioned in 2013. Production will then increase to 5.0 Mtpa on its way to an ultimate rate of 6.0 Mtpa in 2016.This paper will focus on the capital development and infrastructure requirements for the underground mine. Areas covered include mine accesses, ore handling system, accommodations for the dip of the orebody, primary ventilation design, dewatering systems and selection of an underground workshop over surface only maintenance.Discussions include the complications arising due to the mine being located directly below a large open pit and the combination of first principle cost analysis and risk assessment which has been used to safely optimise the feasibility study designs.

Mar 21, 2011

By G Milligan

This paper describes how water is being planned, managed and used in Queensland as both a precious natural resource, vital for healthy ecosystems, and as a valuable tradeable commodity, necessary to secure economic prosperity. Queensland has been progressively implementing a planned package of water industry improvements agreed by the Council of Australia Governments in 1994. The Water Act 2000 provides the legislative basis for implementing the COAG water reform framework in Queensland and sets out statutory water planning processes. A Water Resource Plan (WRP) is a strategic document that specifies water sharing and environmental flow outcomes across a whole catchment over a period of up to ten years. A Resource Operations Plan (ROP) sets out the details of implementing a WRP, including environmental flow rules, establishment of tradeable water allocations that are separate from land, rules for water trading, rules for operating water infrastructure, arrangements for the release of any unallocated water identified in the WRP, and requirements for monitoring and reporting. Water Resource Planning and Resource Operations Planning are progressing in priority catchments and aquifers across the State. Ways to obtain a water entitlement now depend on whether a WRP and/or a ROP exist in a particular catchment. Water trading provides for the buying and selling of water entitlements on a permanent basis where permitted under a ROP. Details of tradeable water allocations are securely registered on the Water Allocations Register, which is similar to a land titles register. Leasing and temporary transfers of water entitlements are also possible. Water brokers are emerging to facilitate water trading which aims to improve water use efficiency and move water to higher value uses. Queensland is leading the way in the implementation of the COAG water reform framework and the pursuit of sustainable water resource management. The StateÆs progress in this regard is increasing certainty for water users, while ensuring that considerations of equity amongst existing and future users and amongst various uses, as well as considerations of ecological sustainability and the wider community, are all taken into account. The mining sector stands to benefit substantially from these new approaches to planning, managing and using this precious resource.

Jan 1, 2003

By J Benn, V Kuznetsov, G Timms, A Spain

Earthen covers are now widely used in the mining industry to control the generation rate and/or release rate of low quality drainage from piles of sulfidic minewastes. Covers are usually designed to reduce the water infiltration rate and in some cases may also reduce the oxygen flux to the underlying sulfides. Engineered covers have only been used since the 1980s, however, and there is very little field data on their performance in the longer term. This lack of information has implications for the degree of confidence that can be placed on the predictions of the environmental impacts of sulfidic minewastes, for the acceptance of close-out criteria by regulatory authorities and for the financial liability of the mining industry. Covers were placed on sulfidic waste rock dumps at the abandoned Rum Jungle uranium mine during 1984 - 1985. These covers were designed to reduce the water infiltration to less than five per cent of incident rainfall by both water shedding and storage-release mechanisms. Regular monitoring by the Australian Nuclear Science and Technology Organisation (ANSTO) demonstrated that the covers performed better than the design criterion for around ten years, but infiltration rates have subsequently increased. There is a 66 per cent probability that the infiltration rate now exceeds five per cent of incident rainfall. The cover on the largest pile, WhiteÆs heap, was sampled in pits dug at eight locations. Sampling was carried out at the end of the monsoonal wet season and again at the end of the ædryÆ season. This, together with laboratory testing, enabled cover performance to be assessed against five criteria: design, construction, cover material characteristics, physico-chemical characteristics and biological characteristics. We are of the opinion that the design of the cover was suitable to achieve the objectives of stability, water shedding, storage-release, and provision of a substrate for vegetation growth. Over most of the surface of the heap, the construction of the covers, drains and erosion prevention structures was in accordance with design specifications. However, several small and localised bare patches on the upper surface of WhiteÆs heap coincide with a reduced cover thickness, which is likely to have been due to poor construction in those patches. The construction of covers on minewastes is dependent on an adequate source of material meeting design specifications. From our limited examination, it appears that there was shortage of material for each of the three zones û a lower impervious clay layer, the moisture storage-release layer and the upper erosion-resistant layer for vegetative growth. An indication of this was that the upper layers in some areas were observed to be thinner than specified. We are of the opinion that this shortage of suitable material has been responsible for some of the changes observed ten years after emplacement. Physical and geotechnical testing indicated that the cover materials no longer meet the original specifications. In particular, the permeability at the 8 locations was found to be greater than specified, by up to several orders of magnitude. The higher permeability may explain the higher observed rainfall infiltration and moisture content of the waste rock. This increased permeability appears to be due to a combination of biological and physical processes û galleries formed by termites and ants and an extensive system of shrinkage/desiccation cracks formed by the development of a polygonal blocky structure involving the entire lower clay layer. The desiccation cracks may fill with coarser illuviated materials and form a conduit through which roots access the underlying waste rock. Measurements were made of oxygen flux into the heap as cover layers were excavated in the pits. They indicated that the full cover currently reduces the oxygen flux to 20 - 23 per cent of that into bare waste and that this reduction seems to be proportional to the cover thickness. It was also found that the oxygen flux into the cover is about four times higher at the end of the dry season than at the end of the wet season and that the difference is due primarily to the difference in moisture content of the cover. Recommendations are made for the design and construction of covers.

Jan 1, 2003

By F M. Weir, M Fowler

The design of excavations in rock must, implicitly or explicitly take into consideration the influence of small- and large-scale geological structures. For most sites the complexity of a fractured rock mass is best captured using a 3D fracture system model based on field data. A discrete fracture network (DFN) approach involves stochastic modelling of the ‘smaller scale’, nondeterministic structures. For slope stability or tunnelling projects DFN modelling provides a valuable geotechnical tool for characterisation of a rock mass and identification of likely failure mechanisms.This paper presents a suite of the DFN modelling undertaken for the design of a large open pit in Australia. The proposed pit is to encounter a 160?m thick, high strength, sheared shale unit, which overlies a crystalline basement. DFN modelling was undertaken separately for both the shale and basement units. While the model inputs and development for each unit are briefly presented, the focus of this paper is on the various applications of the DFN modelling.A key advantage of the DFN approach for design studies is its probabilistic application to structural analyses and results. Multiple realisations of the same model were generated for both the shale and basement units, with the stability analysis carried out on each iteration. The generation of a large number of DFN models and analyses allow assessment of wedge volume, factor of safety and proportion of unstable slope for a range of conditions. The DFN modelling at the case study site was also utilised for a number of other purposes. For example, investigation of likely fault lengths in the shale unit and combined rock mass and defect failure. The development of this tool has been influential in improving our understanding of fracture networks for excavation design.CITATION:Weir, F M and Fowler, M, 2014. Rock mass characterisation and analysis for excavation design – a discrete fracture network approach, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 445–456 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By I Haine, J Penm, T Waring

During 1999 there was a considerable turnaround in world prices for most minerals and energy commodities, except for the bulk commodities (coal and iron ore). The main reasons for this turnaround were: improved prospects in demand for most minerals and energy commodities in the Asian region following a return to both economic and industrial production growth in key economies in that region; continued moderate growth in demand in Europe and North America; substantial production cutbacks in a range of minerals and energy industries; effective reductions in the supply of oil by OPEC nations; and an announcement by European central banks that they would cap the amount of gold they sell and loan in the next five years. Most of these influences are expected to be sustained into the first years of the new millennium. In 2000, with exception of coal, average world prices of minerals and metals are forecast to rise significantly. Gross domestic product and industrial production is expected to grow in some European countries and most Asian countries in 2000 and, with moderate growth expected to be sustained in the United States, demand for minerals and energy is expected to increase. AustraliaÆs main bulk commodities, iron ore and coal, saw prices set for 1999 - 2000 at substantially lower levels in negotiations in early-1999. Double digit price cuts were locked in. However, similar falls appear to have been avoided for coal in Japanese Fiscal Year 2001, while increases of between four and six per cent were achieved for iron ore. Forecast modest recovery in economic growth in Japan and increasing demand elsewhere in Asia are expected to lead to tighter market conditions in 2000. Beyond 2000, world minerals and energy markets will be influenced by the expected robust global supply responses of minerals and energy companies, against a background of sustained economic growth and industrial production growth in major consuming countries. Over the medium-term, a return to declining real prices which have been evident for most commodities in the recent past, is expected as exploration, mining and processing technological change and associated productivity growth continues to reduce industry costs. While lower rates of exploration and mining investment in Australia between 1998 and 2000 will modestly constrain the rate of future industry expansion, Australia remains an important contributor to expected growth in global minerals supply over the medium-term. Australian mine production is forecast to grow between 1999 - 2000 and 2004 - 05, boosted by production from recently commissioned mines and minerals processing facilities and comissioning of other projects at advanced stages of planning.

Jan 1, 2000

The Tom's Gully gold mine is located 90km ESE from Darwin, in the Northern Territory of Australia. The orebody is the auriferous portion of a large sulphide rich quartz reef, hosted in the Wildman Siltstone Formation of the Early Proterozoic Pine Creek Inlier, at the NH extremity of the Mount Bundey granite-syenite intrusion. It was discovered by Carpentaria Exploration Company Pty Ltd on November 17th, 1986, using stream sediment geochemistry.The reef is 800m long at surface, strikes E-H and dips approximately 300 to the south, becoming progressively less steep. Only the eastern half of the reef is auriferous, with gold grades averaging 9 g/t plus anomalous silver, base metals and arsenic.The enclosing siltstone is a dark grey banded carbonaceous and pyritic metapelite, showing areenschist regional metamorphism and thermal effects from the adjacent pluton. Local folding plunging gently SW is cut by a south dipping fault, probably a thrust, in which the reef was later formed at about the time of the granitic intrusion. The main sulphides in the reef are pyrite and arsenopyrite, with gold occurring as microscopic particles in...

Jan 1, 1990

By C A. Chaves

During most of its history, the metallurgical industry has been seen as a source of pollution for the environment. However, during the second half of the 20th century, as the world environmental legislation became more protective and the global environmental conscience consolidated, this landscape began to change. Metallurgical activities have become increasingly related to the social and environmental impacts caused by human activities. With the adoption of environmental management in steel plants, there has been a significant change in steel-related activities which have begun to introduce modern plants, managed with environmental, social and productive efficiency. More and more, steel companies search for a decrease in negative impacts of their industrial operations on the environment, fitting them to the current environmental legislation and even increasing productivity and profitability. The steel industry has started to become a clean and more efficient industry. This work presents a case study of a sustainable steel plant project, located in an environmental preservation area. The project includes treatment and reuse of industrial liquid effluents, air emissions control, noise control, recycling, recovery and adequate waste management. It also incorporates production processes using clean technologies, capable of coproducing energy resources which may be used in the plant showing how is it possible to produce steel with environmental and social responsibility and even increase the enterpriseÆs profitability.

Jan 1, 2009

By N McIntyre, M Edraki, K R. Jain

From the very early stages of a mining project, there is a requirement to predict the chemistry of potential drainages from various waste storage facilities. However, using relative masses to scale chemical loads measured by laboratory kinetic tests, such as humidity cells, to a full-scale mine waste facility will lead to concentration predictions that are unrealistically high for many dissolved constituents. Scaling factors developed by various procedures indicate that laboratory rates may range anywhere from two to eight times (Drever and Clow, 1995) to 100 to 1000 times faster than field rates (Malmstrom et al, 2000; Smith and Beckie, 2003; Ritchie, 1994). This contribution will use previous works and secondary data to discuss the significance of scale in water quality predictions. It will also present primary experimental geochemical and numerical data from a column leaching study on coal spoils to discuss potential applications of mesoscale leaching tests in bridging the gap between bench-top tests and field scale trials.

Aug 2, 2023

By R Bradford, W Gift-Agbey, T Vorster, P Morgan, E Grobler

The Asanko Gold Mine in Ghana started processing ore from the Nkran pit in January 2016 at a production nameplate of 3 Mt/a. The flowsheet is a conventional SAG, ball mill and pebble crusher (SABC) with gravity-gold and carbon-in-leach (CIL) recovery. The nameplate production was comfortably achieved within 3 months, so much so, that it was clear the SABC circuit was capable of processing more than the downstream section of the plant. Consequently, a program of de-bottlenecking was initiated to rectify volumetric capacity constraints. This program was later referred to as ‘Project 5 Million’ (t/a) or P5M. Having completed the de-bottlenecking exercise, it became evident that the SABC circuit could not reach 5 Mt/a solely on hard rock from Nkran. The new challenge was therefore to increase the capacity of the milling circuit through a focused comminution initiative that would address the following: geometallurgical treatment plan; upfront fragmentation requirements; installation of feed and mill monitoring equipment; and integration of a knowledge-based control strategy. This paper takes the reader through the various measures implemented to increase the milling rates and to create a stable/ sustainable control philosophy. As a result of the implementation of advanced mill performance monitoring technology (MillSlicer) and the collaboration between a team of experts in comminution, control and operations, the Asanko Gold Mine process plant feed tonnage has successfully increased from 3 Mt/a to 5 Mt/a.CITATION:Bradford, R, Gift-Agbey, W, Grobler, E, Morgan, P and Vorster, T, 2018. Optimisation of Asanko’s Obotan SABC circuit to achieve ‘Project 5 Million’, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 477–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By B K. Da, S A. Balaji, G P. Roy, T K. Dutta

The raw material handling complex at the Durgapur steel plant provides iron ore, crushed coke and flux to two sinter plants. Either some facilities were not envisaged or not properly designed before the project stage which caused problems during operation of the plant. The absence of an in situ roll turning facility, used to increase maintenance activities for disassembly, transportation of rolls to central machine shop and assembly of rolls, led to decreased crusher availability and increased activities for the maintenance crew. The provision of a smaller vibro feeder/screen in place of a suitable sized screen caused jamming of the screen deck, adversely affecting screening efficiency and the crushing index of crushed coke. Some design modifications and developmental work was undertaken, such as the development and installation of an in situ roll turning facility in the existing limited space, achieving low feed (0.1 - 0.2 mm/rev), lower cutting speed of 30 - 40 m/minute for 350 BHN hard roll, which was also a difficult engineering challenge to bring within the tolerable limit of vibration. This was successfully achieved. Modifications to the screen deck, introduction of differential speed crushing and modification to the vibro screen and vibro feeder for uniform distribution of feed have been incorporated. These innovative design modifications to the in situ roll turning have led to a drastic decrease in maintenance activities and an improvement in the crushing index. Modifications to the screen have resulted in the elimination of jamming and improved screening. Modifications to the vibro screen before the primary crushers and to the vibro feeder before the secondary crushers have prevented excessive wear in the central portion of rolls, ultimately leading to increased roll life. Incorporation of differential speed crushing has resulted in an increased crushing index and decreased generation of micro fines. All the above modifications have led to distinct improvements in equipment availability, increased roll life and a decrease in maintenance activities and improvement in crushed coke granulametry, ultimately resulting in improved productivity and quality of iron ore agglomeration at the sinter plant. The innovative design modifications mentioned above are discussed in detail in this paper.

Jan 1, 2005

By R F. Sandenbergh

Due to environmental considerations, mineral processing plants are increasingly recycling water to decrease the impacts of wastewater on environment and the depletion of fresh water resources. Industrial experience has shown that increasing recycling water in flotation typically negatively impacts the recovery and selectivity, especially in the selective flotation of minerals from complex sulfide ores. The major reason for the reduced selectivity is typically the inadvertent activation of sphalerite or pyrite by the heavy metal ions (HMI) in solution. These HMI are often produced during milling and flotation and absorbed by other minerals. In the normal flotation pH value range (8 - 10), these HMI are often in the form of precipitates or complex ions that may re-appear in solution or become active should conditions favour this. In this paper, microflotation, batch flotation and XPS surface measurement were used to investigate the use of HMI absorbents additions to the pulp to improve flotation selectivity of a complex sulfide ore. It has been demonstrated that HMI removal does improve flotation selectivity by facilitating more effective depression of the sphalerite. Microflotation and XPS surface measurements have shown that HMI absorbents compete with sphalerite to absorb HMI, and thus reduce the surface concentration of HMI on those sulfides. The practical use of HMI absorbents in complex sulfide ore flotation is also discussed.

Jan 1, 2005

By B Maybee, L Fava, D Millar

In the context of a case study for an underground gold mine, the value generated by a schedule optimisation tool (SOT) is assessed. SOT is a software tool for underground mine planning that maximises the net present value (NPV) of a development and production schedule. A baseline study measures the NPV of a schedule generated by SOT from a sequence prepared by the site mine planners. Operational resource constraints and precedence constraints are adhered to by the schedule and NPV is evaluated with a financial model including revenues, costs and discount rate, as specified by the mine planner.The case study has several facets in addition to the baselining component. Scenarios were conducted that examined the degree of constraint on operational resources, the projected gold price and unit costs. Life-of-mine schedules subject to optimisation using SOT allowed for equitable comparisons.Haulage was identified as a dominant constraint for the mine. It was one of six operational resources that were used to constrain the optimisation of the mine schedule, with alternative levels for some of these constraints being identified so that their effects on the NPV could be studied. Alternative price projections for gold and different cost projections were identified and their effects on the optimised schedule examined. Price and cost scenarios that brought additional economic material into the schedule at various times in the mine life were considered in comparison to a scenario that assumed no additional economic material would become available.This case study illustrated that the use of a schedule optimisation tool to optimise mine schedules provides mine planners with an ability to perform a wide variety of analyses in a relatively short period of time. Such tools thereby support strategic decision-making that can add significant value to an orebody.The case study demonstrates that by fixing the set of development and production activities to be carried out before optimising the life-of-mine schedule, the mine planners can inadvertently set up a situation where the NPV would be progressively eroded in the last several years of the mine life. This clearly illustrates the need for schedule optimisation to be integrated with life-of-mine planning.CITATION:Fava, L, Maybee, B and Millar, D, 2012. Decision support for an underground gold mining operation - A case study using the schedule optimisation tool, in Proceedings Project Evaluation 2012 , pp 41-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By R Symes

The Fosterville Goldmine in Victoria Australia employs the BIOX« Process to liberate gold from its sulfidic flotation concentrate through bacterial oxidation. Gold occurrence is primarily as submicron particles in pyrite and arsenopyrite and has been described as being in æsolid solutionÆ and therefore not amenable to direct cyanidation. Once liberated by the oxidation process, the gold is then available for cyanide leaching. During the oxidation process it has been found that a portion of the liberated gold becomes suspended in the liquid phase in what appears to be a colloidal state. This liquid becomes a waste stream during washing of the oxidised solids and the suspended gold is therefore lost. A method was previously developed using an addition of quebracho tannin to significantly reduce this loss by formation of an iron-tannin precipitate which captures the gold which then reports to the cyanide leach circuit with the oxidised concentrate solids onto which it is adsorbed.This paper discusses the development and plant trial of a second processing step to further enhance gold recovery by use of flotation tailings essentially as a source of extra surface area to capture residual tannin-iron precipitate and its associated gold not recovered in the first step.CITATION:Symes, R, 2012. Recovery of colloidal gold from oxidised concentrate wash liquor - Further improvement, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 383-388 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Kelly D, Moore C

The Golden Mile, which has been mined continuously for the past 100 years by both underground and more recently open pit methods, occupies an area of 1.2 km by 4 km adjacent to the city of Kalgoorlie Boulder in Western Australia (Figure 1). Large-scale open pit mining at the Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston operations is currently extracting 7.8 million tonnes of oxide and sulphide ore for a total production of 522 000 oz per annum. The effectiveness of grade estimation techniques at KCGM has been examined with reference to existing 10 m bench sample data from all operating areas within the Eastern Lode System of the Main and North pits. The aim of the study was to recommend practical parameters for grade control estimation. The review included comprehensive variography and comparison of nonparametric estimation methods (Joumel, 1983) such as indicator kriging and probability kriging with ordinary kriging, leading to the development of improved grade control parameters and procedures for both daily quality control and short term mine planning. This paper reviews the geological, statistical, geostatistical, mining and modelling features studied in order to present KCGM's Mining Department with recommendations for improving grade control.

Jan 1, 1994

This paper is directed at the problems flowing from Australia's capital gains tax (CGT) on the disposal of exploration and mining tenements both in Australia and overseas. It will seek to identify the issues and give some idea of the dollar consequences of decisions lacking forethought. The paper should not only be seen in the context of Australian tenements. CGT applies to the disposal of any assets by an Australian resident anywhere in the world. Offshore incorporated companies are not necessarily free from CGT risk where it can be shown that control management and control of the relevant company is in Australia. Also the disposal by non residents of Australian tenements are potentially caught by CGT. Some will ask what has taxation got to do with a valuer who merely determines the value of assets. These days no determination can be blind to the consequences. Whether the consequences can encourage a movement in value is another thing dependent upon the circumstances; but? A role of an experienced taxation consultant is to point out parameters within which associated professionals can work. The parameters will vary from case to case, but these when clearly indicated may be of help to persons such as valuers. When one comes down to it real estate salesmen are never wrong. They have a feel for the market and almost through self fulfilling prophesies achieve sales at their guestimates. Whether they could have achieved higher considerations become virtually academic in the process. Of course I am not suggesting that tenement valuers can be compared to real estate salesmen, or am I? What is the value of a tenement? Is it the DCF/NPV type of generated value based on a large number of variable factors (ie what one may call the fundamental value)? Or is it what another may pay to purchase that tenement if it were on the market at an instant point in time? How big is the market, the quality of the bidders, the size of their purses, the needs of the buyer for comfortable fit, the premiums for foreigners, the standard of the marketing, the industry intelligence level of the bidders, the obligation to farm/sell down? The list goes on endlessly. One question must be.asked-"Is a range of values acceptable for tax purposes". ie Would any tax consultant ever provide a valuation to the Australian Taxation Office that indicates three or more possible values ie

Jan 1, 1987

By C Hedemann, N Silveste, H Davis, C J. Moran

For nearly two decades water scientists have been debating the need to use appropriate models for the questions being asked and the data available. This paper puts forward a rationale for a hierarchical framework for water balance modelling as it applies to mine sites. The hierarchy is based on the complexity of models and their data requirements. Scientific models are the most complex and require the most data; next is engineering models, then systems models and the simplest representations are given by conceptual models. A position is put forward that systems models have a range of uses that the others do not provide. A systems model, called SiteMiser, is described and its calibration illustrated. The model is applied to seven coal mines from the Northern Bowen Basin in Central Queensland. Currently, there is little relationship between total water use and coal production. This relationship is not any stronger when fresh (raw) water is compared to reused water. Leading practice water use levels are simulated for all sites. The simulation results demonstrate that there is considerable opportunity to reduce water consumption and, in particular, to import less fresh (raw) water to the sites.

Jan 1, 2006

By C T. Portelli

Belt conveyor transfers are the most likely location for high wear rates and failures. Belt transfers are necessary to change the direction of conveyed material and will remain a part of belt conveyor systems into the future. Burden being accelerated due to fall and changes in direction from one system to the next, prevents steady state flow which introduces component fatigue. The conveyor belt is considered the greatest cost item over the life of a belt conveyor system and consumes considerable downtime to replace, therefore a financial incentive exists to preserve this high-cost item. Other issues created at the transfer include health risks of uncontained dust and product losses due to spillage. Additional consideration to support the belt is one way to improve the life of components and contain dust within the transfer chute. The humble impact cradle/bed has changed little over the years whilst conveyor systems have achieved ever greater flow rates. Further development of the impact cradle is an opportunity to reduce maintenance costs and increase uptime. The peak technology on the market for conventional impact belt support is the dynamic impact cradle, which ensures the belt support area under the chute allows for some dynamic travel, whilst also maintaining a consistent skirt board area. The impact energy at a transfer when installed with Kinder Australia’s dynamic impact belt support system was measured to further understand the forces involved and how they compare with static belt support systems. Adding further dynamic capacity to the load zone has been shown to increase belt life by at least 30 per cent. Other components also benefit from reducing impact energy in the transfer and the incorporation of polyurethane bushes at roller supports has been employed further increase roller and frame life. Kinder Australia has developed a unique and innovative range of belt support technologies that further promote dynamic travel whilst maintaining a consistent skirt board area without a significant increase in belt-friction tension. This technology combines slider rails with rollers that can absorb impact independently within the support system and/or utilising exotic slider materials to overcome high belt speeds and/or system capacities. Kinder Australia has a vast library of documented case studies and application data to ensure the future systems being offered will survive, provide better chute sealing and protect the conveyor belt.

Sep 18, 2023

By R Pinksen

The Iron Ore Company (IOC) of Canada Mining and Operations Departments expressed an interest in reducing the amount of oversize material (>1 m × 1 m × 1 m) being produced and its subsequent downstream effects including in-pit sorting and reduction, damage to mobile equipment, and significant delays in the loading pockets and the primary crushers. To achieve this goal an oversize reduction project was undertaken by the mine and to date has significantly improved upon baseline measures.One key approach used to reduce the amount of oversize was the implementation of thicker emulsion. The introduction of a thicker emulsion into the blastholes provided more resistance to the forces created by dynamic water and reduced the infi ltration of the emulsion into the cracks and fissures of the rock mass. Blast results showed reduced amounts of oversize and more consistent fragmentation throughout the muck piles. Additionally, a significant reduction in nitrates leached into the mine water discharge has been realised.To determine the effectiveness of the oversize reduction project, IOC used shovel based camera technology to assess fragmentation presented to the shovel at the digging face. A digital vision system (DVS) was installed on one of the shovels to capture images that were stamped with global positioning system (GPS) locations. A large population of digital images was analysed to produce a robust fragmentation distribution baseline that was used as one of the mine key performance indicators (KPI). Changes to blasting practice were subsequently measured against the baseline KPI to assess effectiveness.

Jul 11, 2011

By J P. Evert

Didipio gold-copper mine operation is situated in the island of Luzon, approximately 270 km north of Manila in the Philippines, in an area of high seasonal rainfall. The hydrogeological water flow model implied that there would be high connectivity between regional structures and underground operations. This model predicted that underground mine groundwater inflows were expected to quickly rise as the decline progressed to a peak of 510 L/s. Designing a capital pump station to deal with 510 L/s has its own challenges, however developing the decline down to the required level, always dealing with 300 L/s of water and constructing the pump station is extremely challenging and required a robust water management plan and mine design. When dealing with expected high volumes of water, underground mine design and scheduling plays a key role in protecting electrical infrastructure, equipment, secondary pumps, and the decline from flooding. A good drainage system and controlled dewatering plan is essential for safety and progress. This paper details the dewatering techniques and mine designs required to accomplish decline development with high water inflows as used in the Didipio project. It will describe the learnings and outcomes that are achievable with a flexible design, as new structures are mapped, and water intersections are increased. It also highlights the potential for adaptability in mine planning to provide evolving improvements or to evade problems that are expected from the constant reconciliation of data recorded during development.

Mar 29, 2023

By Kilgour I

The installation of a final cleaning column at Ok Tedi Mining Limited was carried out to increase final concentrate grade in order to reduce concentrate handling, shipping and treatment charges and to reduce penalty payments. To fast-track the project a decision was made to install a full-size column on one of the two parallel circuits, designed on information readily available and utilising the experience of mill staff and an engineering consultant, rather than delay installation while a pilot scale program was conducted. A 3.66 m diameter by 12.8 m high column was installed to produce 40 t/h of final concentrate from a combination of rougher concentrate and recleaner concentrate. The column design and sparger system were by Cominco Engineering Services Limited.

Jan 1, 1991