Search Documents

By A A. Latscha, D O’Connor

Increasing orebody complexity, restrictions in ground access, and longer lead times for disturbance approvals, have generated the need for the Resource Development Team within Rio Tinto Iron Ore (RTIO), to explore optimised drill design techniques that deliver resource conversion value while maximising program outcomes. In response to this challenge, the Team initiated a case study to produce an AI assisted/designed drill program using a non-machine learning AI. The case study involved the assessment and implementation of an AI generated drill program at one of RTIO’s Pilbara iron ore deposits, located in the Hamersley Province of Western Australia. The Mineral Resource is currently classified as 100 per cent Inferred. Access constraints inherent to topography, and the presence of exclusions zones have prevented adequate drilling coverage, resulting in lower resource confidence and a poor definition of the orebody extents and geometry. The drill campaign, planned in Q1 2023, needs to consider access constraints, complex topology and the limitations related to additional ground clearance, while addressing the requirement of improving orebody knowledge. The drill plan had to address two objectives. The first and main aim of drilling was to upgrade the Resource Classification to allow for possible conversion to Ore Reserve. The input for this objective was a volumetric representation of the areas currently not meeting pre-defined quantitative Resource Classification upgrade criteria. The second objective was to better define the orebody extents and geometry. For the second objective, the input to the drilling optimiser was a volumetric representation (blocks) of the areas of high uncertainty in the mineralisation/waste boundary, which were defined using an indicator conditional simulation technique. The drilling optimiser output was a range of compliant drill plans. A set of KPIs based on economic and orebody knowledge criteria were used to assess the plans and to select the most optimal drill design to be drilled in 2023. The geology and management teams were able to make better informed, objective decisions using the trade-off between cost and orebody knowledge gained. As part of the assessment, the AI generated plans were compared to our current planning practises. The AI assisted plans, when gauged against the project KPIs, showed clear and measurable improvements in both meeting project objectives and in managing operational risk.

May 24, 2023

By W D. Erskine, M J. Saynor

Ranger Uranium Mine, surrounded by Kakadu National Park is located in the Alligator Rivers Region (ARR) in the wet-dry monsoonal tropics, 250 km east of Darwin, Northern Territory. A trial landform (TLF), measuring approximately 200 m by 400 m (8 ha) was constructed during late 2008 and early 2009 by Energy Resources of Australia (ERA), adjacent to the northwestern wall of the tailings storage facility at the Ranger Mine. A collaborative research program involving the Environmental Research Institute of the Supervising Scientist (eriss) and ERA, has been underway to measure long-term (five to ten year) rainfall, run-off, sediment and solute losses, seepage and vegetation establishment on the TLF (Saynor et al, 2012; Lowry et al, 2014). This paper reports on bed load losses from four erosion plots built on the TLF. These were achieved by physically isolating approximately 30 × 30 m areas from the surrounding landform on three sides with sidewalls along with an open polyvinyl chloride (PVC) pipe on the downslope side. Each plot was instrumented with a range of sensors. Two plots, 1 and 2 were constructed on waste rock material, while plots 3 and 4 were constructed on waste rock mixed with approximately 30 per cent lateritic material. Plots 1 and 4 had tube stock planted in early 2009, and plots 2 and 3 were initially planted by direct seeding in July 2009 and were infill planted with tube stock in January 2011.CITATION:Saynor, M J and Erskine, W D, 2016. Bed load losses from experimental plots on a rehabilitated uranium mine in northern Australia, in Proceedings Life-of-Mine 2016 Conference , pp 168–171 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By A S. Derrington

High-accuracy, solid-state digital reference barometers have proven to be well suited to conducting underground barometric pressure surveys. The only problem is their expense; at least A$4000 each. For this reason, and because barometric pressure surveys are not a routine undertaking, very few mines have been able to justify the purchase of suitable instruments. The author knows of only three Australian metalliferous mines that own them.However, this may soon change given the recent development of low-cost, mass-produced miniature barometric pressure transducers. These transducers were developed to provide an altimeter function in the latest generation of smartphones. The main purpose of the inbuilt altimeter function is to allow the smartphone to be aware of its altitude when the global positioning system satellite signal is lost.This paper describes a prototype barometer that was constructed using one of the most accurate of the latest generation of piezo-resistive smartphone barometric pressure transducers. The prototype instrument was constructed for less than five per cent of the cost of a commercially available digital reference barometer. The prototype was subsequently tested against a reference barometer at the University of Queensland’s Experimental Mine to verify its accuracy and suitability for measuring pressure differences between underground survey stations.It is expected that the instrument’s low cost will pave the way for barometric pressure surveys to become more commonly used in mines. In turn, the resulting improvement in knowledge of major underground pressure losses should allow mine ventilation officers and engineers to optimise their ventilation systems and potentially reduce overall operating costs.An alternative option would be to use a barometer-equipped smartphone as a survey instrument, provided that its inbuilt barometer module is sufficiently accurate.CITATION:Derrington, A S, 2015. Development of a low-cost instrument for barometric pressure surveys, in Proceedings The Australian Mine Ventilation Conference, pp 331–336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By J Herd, J Rowe, M Cutbush, d F. Aziz

WearApp provides expertise for assessing the degradation of removable screening media panels on vibrating screens right in a user’s pocket. Through the WearApp application, users can simply take a picture of a panel using their mobile, enter some basic information and have the application assess the wear to provide a recommendation for whether the panel needs to be replaced. Where traditional mechanisms for assessing panel wear only measure a few points across the panel face and rely on having personnel with specialised knowledge available to perform the assessment, WearApp uses deep learning models to analyse the entire panel face and support the user to make an informed decision. The application works through analysing a panel image and using a model to automatically detect the corners of the panel. Given the known dimensions of the panel, this enables the application to calibrate the pixel size against a known reference. A second set of models then detect the apertures and measure their dimensions. With the aperture dimensions defined the application assesses the wear of the panel through referencing a stored 3D model of the aperture. Finally, the data from each aperture is collated and the wear of the entire panel face defined. Since WearApp performs measurement of the entire panel face, it also allows the user to perform a more detailed analysis of the panel’s wear profile. Where typically, the panel wear is only measured in a few locations, WearApp’s analysis enables users to visualise the panel wear across the entire panel face, identifying areas of high wear that could be leading to premature panel replacement. Additionally, because the entire panel face is measured the change in screening efficiency can be calculated accurately for the worn panel, even taking into account the impact of aperture pegging by small rocks.

Sep 1, 2024

By W. M. LONIE

Address by the President of the Institute (Mr W M Lonie) in making the presentation of the Certificate of Honorary Membership to Sir Ian McLellan, K.C.G.M, K.B.E. Address by Sir Ian McLellan after accepting the award.

Jan 1, 1979

By M Russ, J Gediga

This paper shows an economic feasible approach to implement greenhouse gas (GHG) reduction measures into the mining and metallurgy industry (MMI). The goal to improve energy consumption is directly linked to the reduction of GHG emissions in the MMI. A baseline scenario of the considered reference system and of the respective reference year has to be designed and analysed. In a second step an analysis of the same operation using the best available technology (BAT) processes is carried out to generate a basis for a benchmark system. The identified gaps will be reported and the potential GHG emission reductions will be put into relation to the investment, running cost and generated carbon credits of the new process technologies to be implemented. This economic feasibility calculation is necessary to realise a cost efficient GHG reduction roadmap decision-making for implementing new technology into the companyÆs business operations. The GHG reduction roadmap is developed using the marginal abatement curve approach.

Jan 1, 2009

The Woodcutters deposit, 65 km south- southeast of Darwin, N.T., consists of a series of veins of pyrite, sphalerite, and galena with some silver, cadmium, antimony, and arsenic minerals. The veins are hosted by the Early Proterozoic Whites Formation, a sequence of black slates with interbedded carbonate rocks and minor ash tuffs. The known orebodies occur about 300 to 500 metres above the contact of Whites Formation with the underlying Coomalie Dolomite, which consists of dolomite and magne- site. The stratigraphic setting is lithologic- ally similar to that of the Mt. Isa deposit, Queensland. The orebodies are replacement veins occ- urring along fault and dyke structures which are sub-parallel to the axes of a double-nosed faulted anticline. The orebodies are in part associated with two unusual carbonatized lam- prophyric dykes. The dykes were intruded after the fold and its slaty cleavage were formed. The ore has replaced the dykes and host rocks and is therefore late-stage hydrothermal miner- alization. The known orebodies are open at depth. A "bonanza" of high-grade ore occurs at the upper part of the largest orebody and is currently the subject of an open cut mine planning study by a consortium of companies headed by Nicron Resources Ltd.

Jan 1, 1984

By W Kendall

Ore sorting has the potential to reduce the feed to wet plants and in the case of complex orebodies that can significantly reduce the water, energy and reagent consumptions and resulting operating costs for the project. The application of ore sorters has sparked renewed interest and application in the precious and base metals mining industry in recent years as a result of the continuing development of new sensing technology and very fast information processing that is making ore sorters applicable to a much wider range of ores and larger scale operations. The application of ore sorters involves a range of trade-off decisions that have economic impact upon the benefits of ores sorting to the project under consideration. This paper will present some typical trade offs to be considered and their impact in a particular project setting. CITATION: Kendall, W, 2018. How economics drive the application of ore sorting, in Proceedings Complex Orebodies Conference 2018, pp 24–27 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By R G. Moreby, S Bluhm, FávonáGlehn, C Pascoe

Resolution Copper Mine in Arizona, USA, is planned to be a 2000 m deep panel cave mine with virgin rock temperatures exceeding 80¦C in rock with high crystalline silica content, resulting in a very challenging ventilation and cooling system design. This is one of the largest copper orebodies ever found and, with a planned rock production rate of 120 kton/day. The project is currently in its prefeasibility phase and the paper discusses features of the ventilation and cooling system design which includes multiple ventilation shafts with total primary ventilation flow of about 3000 m3/s and both surface and underground refrigeration plants producing more than 140 MW refrigeration capacity. The cooling system features large surface bulk air coolers chilling all downcast air supplemented by an underground secondary air cooler system and a chilled service water system. This will be a very challenging mine to ventilate and cool but this work has demonstrated that it will be technically achievable with the application of existing technology.CITATION:Bluhm, S, Moreby, R G, von Glehn, F and Pascoe, C, 2013. Life-of-mine ventilation and refrigeration planning for Resolution Copper Mine, in Proceedings The Australian Mine Ventilation Conference , pp 125-138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Hermulheim W

In the Federal Republic of Germany hard coal is mined underground only. The coal mines reach down to 1 500 m deep, recently having an average depth of 900 m. The commonly used winning system is long- wall mining with face lengths up to 250 in. The gate roads, which separate the seam into single panels, have an average length of one kilometre with a cross- section up to 20 m2. These single entries are usually supported by yielding steel arches. The installation of steel arches can hardly be mechanized. The choice of heavier support, caused by increasing depth and roadway cross-section, results in high cost for labour and material in gate roads. Furthermore, the heavy steel arch is acci- dent-prone, not only during installation but also during transportation and ship- ment. Rock bolts combined with a suitable lagging offer a way of mechanizing support work in headings. The aim is to decrease cost and to increase mine safety and pro- ductivity. Over the last ten years, 50 km of gate roads have been reinforced by a combination of rock bolts and weld mesh. Nevertheless, there are still differing opinions on the feasibility of rock bolting in gate roads. In Germany a long tradition and experience with steel arch support exists, whereas the function of an anchorage is a closed book to miners, preventing this new technique from spreading more quickly. Advantages and shortcomings of both steel arch support and rock bolting are compared. The experience with rock bolting up to now is reported. Possible improve- monts arm discussed.

Jan 1, 1986

By Szwedzicki T, Jiang J

The acoustic emission (AE) technique has found wide application in rock engineering. Generally, acoustic emission, which is produced by a rapid microcrack growth, is an ubiquitous phenomenon associated with brittle fractures and can provide information on the failure process in rocks. The sudden release of stored energy in the form of an elastic stress wave that travels from the point of origin within the material to a boundary is called an AE signal or a discrete AE event. Based on a number of experiments and analysis, the correlations among the rock type, the complete stress-strain behaviour, mode of failure and AE properties are investigated and the AE pattern has been classified as four types: single-peak AE, double-peak AE, continuous AE and absent AE. Each type of AE pattern corresponds to a certain type of rock and is largely related to the internal structure and imperfection of a rock. Applications of the AE technique in stability monitoring, in situ stress assessment and seismic source location are also discussed.

Jan 1, 1995

Coal geology plays an essential role in the investigation of in situ coal seam quality. Coal geology can also play an important part in laboratory studies such as coal washing and coking, and in operating plant problems.

Jan 1, 1976

By Holliday R, Floyd JM

A laboratory investigation was carried out to determine the distribution of gold between the products of lead-zinc concentrate smelting in the Imperial Smelting Furnace (ISF). Bullion, speiss and slag from the ISF at Cockle Creek were used as the starting materials to evaluate the effect of gold and copper content of products on the distribution of gold between phases under conditions simulating those in the ISF hearth. The ratio of gold in bullion to gold in speiss has a mean value of approximately 1.6 and is independent of the gold content of the bullion. The distribution coefficient of gold between bullion and speiss is dependent on the copper level in speiss and is lowered by increasing copper content in speiss. The ratio of gold in bullion to gold in slag is in the range 25 to 5700 and dependent on the gold content of the bullion. For low gold concentrations in bullion of the order of 1 g/t and a bullion to slag ratio of 1:3 the gold loss to slag is expected to be approx- imately 23%. In all tests the gold in slag remained low, in the range 0.05 to 0.5 ppm provided metal prills were not suspended in Slag.

Jan 1, 1986

By D Genge, E Martin, T Goswami, M Rothery

Rio Tinto’s Hunter Valley Operations is a large open pit coalmine situated in the heart of the Hunter Valley in Australia. The Riverview West Pit has faced increasing production challenges in recent times due to decreasing dragline strike lengths and increasing environmental constraints on vibration, overpressure and fume generation. Conventional mining techniques would involve five to six production blasts per strip to recover multiple coal seams. Each blast event carries the risk of exceeding the strict environmental requirements. By working collaboratively with Orica, it was realised that the blasting method known as Stratablast™, in conjunction with advanced computer modelling techniques, could provide productivity gains whilst simultaneously providing more control over the environmental effects and the impact on nearby infrastructure.As a result of this change, the number of blasts per strip was reduced to one, with the implication that a great deal of care and forethought was needed to manage the increased challenge posed by multiple constraints in the proposed mining area. This innovative approach of combining throw and stand-up blasts allowed the extraction of all major coal seams in a single pass blast event. The blasts were initially designed with a large factor of safety to stay within environmental limits as they were over 1.1 km in strike length, with more than 800 holes and with a total charge weight of about 1000 t of bulk explosives. Furthermore, there were conflicting priorities around the desired blast outcomes. So far, 11 such blasts have been designed and successfully fired. After each blast, innovative design changes have been iteratively implemented to provide further control over environmental impacts, whilst continuing to improve productivity. As a result of these changes, blasts have progressively increased in complexity with the inclusion of features such as damage zones, mid-splitting, time gaps and different directions of firing. The consequence of this complexity is that the blast duration can be as long as 28 seconds to accommodate all components of the blast.This project has increased the productivity of the Riverview West Pit through blast design improvements and allowed the environmental impacts to be managed with far more control and predictability than would have been possible under a conventional blasting regime. There still remains room for further optimisation of mine productivity and this is being addressed through a process of continuous improvement.CITATION:Goswami, T, Martin, E, Rothery, M and Genge, D, 2015. A holistic approach to managing blast outcomes, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 645–654 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Xueqiu H

Since the hypothesis of coal and methane outburst mechanisms based on elastic mechanics gives no consideration to time, it cannot give satisfactory explanation of the outburst occurrence and its development. A creep mathematical model of coal containing gas has been set up through creep tests and analysis under a condition of triaxial compression. Such a model can explain the phenomenon of coal and methane outbursts successfully. The tests proved that there is no essential difference between the rheological properties of prone outburst coal and non-prone outburst coal. Outburst can take place in any kind of coal if the rheological conditions of coal containing gas are met. The creep mathematical model provides a basis for establishing a comprehensive index of coal and methane outburst potential.

Jan 1, 1992

By Lyman GJ, Davis JJ

Models which have been presented in the literature consider only selected aspects of dense medium cyclone operation, are empirical in nature and generally relate only to severely limited ranges of operating parameters. This paper reports progress towards development of a more comprehensive and robust model. The data base consists of partitioning parameters developed using density tracers and conventional coal sampling and analysis techniques, together with recordings of parameters such as cyclone dimensions, feed pressure, medium size distribution and product media densities.. These data were drawn from 15 Australian coal preparation plants. To elucidate the effects of important operating parameters on medium behaviour and on the partitioning of large particles a series of pilot scale tests was also conducted. The present model consists of eight sub-models which relate to particular aspects of dense medium cyclone operation such as medium flowrates and densities, or size- by-size separation densities and Eps. The model structure follows a logical progression which clearly demonstrates the importance of understanding medium behaviour before attempting to predict partitioning performance. The model also attempts to define the conditions under which yield losses due to unstable "surging" discharge may occur.

Jan 1, 1987

By A D. Bugarski, G H. Schnakenberg Jr

An investigation was carried out at a US underground mine to characterise diesel aerosols and to asses the effects of various control technologies on the concentrations and properties of particulate matter and gases emitted by heavy-duty diesel-powered equipment. This study was dedicated to evaluating the impact on mine air quality of contemporary diesel particulate filter (DPF) systems installed on mining equipment. Additional efforts were made to assess the effect of blended biodiesel fuels, yellow grease and soy, ultra-low sulfur fuel, a fuel emulsion and of selected diesel oxidation catalysts on air quality and emissions. The carbon analysis performed on the collected samples showed that the tested DPF systems reduced the mass concentrations of elemental carbon in mine air by between 70 per cent and 92 per cent. In addition, TEOM measurements, collected during these tests, showed that the total diesel particulate matter concentration in the mine air was reduced by greater than 65 per cent when DPF systems were used. The tested biodiesel blends were found to reduce elemental carbon concentrations in the mine air by between 49 per cent and 33 per cent, for the B20 (20 per cent biodiesel/80 per cent #2 diesel) of soy and yellow grease respectively and between 66 per cent and 56 per cent for the B50 (50 per cent biodiesel/50 per cent #2 diesel) of soy and yellow grease, respectively. The water-in-diesel fuel emulsion was shown to reduce elemental carbon concentrations by as much as 85 per cent. NO2 measurements showed an increase in the maximum concentrations of NO2 when catalysed DPF systems were used instead of mufflers.

Jan 1, 2005

By Quast K. B

Samples of limestone and micaceous hematite have been ground in a laboratory batch mill using equal weights of either rods or balls. Values of the Schuhmann distribution modulus, a, have been shown to depend on grind time and do not remain constant as often reported. The linear reduction in a with grind time was attributed to a change in grinding mechanisms with time. The product sizing from ball milling limestone showed a bimodal distribution, but rod milling produced a unimodal size distribution. The product sizing from milling micaceous hematite was difficult to interpret due to the major influence of the shape factor on the transition from screen sizing to cyclosizing.

Jan 1, 1995

The Mt Muro gold and silver deposit in Central Kalimantan has been in production since December 1994. The geology is characterised by narrow high-grade lodes containing gold and significant amounts of silver. From a largely untrained workforce in the grade control department, production per crew and per geologist has tripled during the three years of production. Grade control drilling evolved from blast hole sampling to reverse circulation sampling. National geologists are trained in basic modeling procedures. A fully integrated reporting and reconciliation system was programed and implemented.

Jan 1, 1997

By A K. Bayer

When the human eye fails in the evaluation of quality parameters in the extraction of minerals the use of laser-induced fluorescence analysis (LIF) can supply more detailed information on the composition of rocks. On the basis of measurements of selected raw materials engineering concepts for the use of this method in the mining industry as an innovative system for horizon control of mining machines will be described and the most important analysis parameters, influencing factors and interference variables are presented.

Jan 1, 2003