Search Documents

The GDR has extensive lignite deposits at its disposal, which formed the basis for the development of an independent energy source after 1945 and which will retain their significance well beyond the year 2000 (see fig. 1). In 1946 lignite output was about 110 x 106 t. In 1985 312x 106 t was produced and in 1988 the planned output will be ca. 315 x 106 t. Thus, the domestic produc- tion of lignite covers ca. 75% of the GDR's primary energy requirements. More than 80% of the electrical energy is gener- ated by the use of lignite and about 12% by nuclear energy. In addition to this, about 18 x 106 t/a mineral oil and about 6 x 109, m3/a natural gas are imported, predominantly from the Soviet Union. The lignite deposits of the GDR are of Tertiary origin and are recovered exclusively by opencast mining. There are two large regions (fig. 2): - in the region east of the river Elbe (Cottbus/Senftenberg- "Niederlausitz") and - in the region west of the river Elbe (Halle/Leip- zig/Magdeburg). These deposits differ in geological age and conditions of depo- sition, consequently there are differences in their chemical and physical composition and, thus, in their uses. The younger Mio- cene coals of the main region in the East of the river Elbe belong to the epirogenetic type and have a low content of ash and sul- phur. Among other things, they are suitable for the production of brown coal high-temperature coke (Lauchhammer and Schwarze Pumpe). The older Oligocene coals of the Halle/Leip- zig region are bitumenous in certain areas. Therefore, they form the basis for production in low-temperature carbonizing and chemical plants. In the Halle-Magdeburg region, where the lig- nite is in contact with the underlying Zechstein subdivision, so- called "salt coals" are found.

Jan 1, 1989

By R Bertuzzi

"This paper presents preliminary results of ongoing research being carried out at the University of New South Wales Australia (UNSW) into improved methods for estimating rock mass strength. In this paper the rock mass strength of Hawkesbury Sandstone is assessed. An estimate is first made based on an extensive database of intact rock strength data being collated by the author and the assumption that rock mass strength can be determined following the geological strength-index (GSI) approach. The resulting strength envelope is then compared with nine documented case studies where stress induced failure has occurred in tunnels excavated within Hawkesbury Sandstone. The case studies cover a range of conditions: construction dates from 1880s to 2006 spans from 3.2 to 12.5 m depths from 17 to 124 m excavation methods of drill and blast, roadheader and tunnel boring machine (TBM).Finite element modelling is used to assess the likely magnitudes of the principal stresses that were present at the time of the failures. The finite element models are interrogated to provide the values of major and minor principal stresses in and around the mapped failure zones. Failure and stable points are then compared to the proposed strength envelope(s) of Hawkesbury Sandstone derived using the Hoek-Brown and the spalling criteria. The ability of the Hoek-Brown rock mass strength criterion to differentiate between the ‘failed’ and ‘stable’ zones is considered to be remarkable.CITATION:Bertuzzi, R, 2014. Estimating the rock mass strength of Hawkesbury Sandstone, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 417–424 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By M Goers, M Almond

"The use of reverse circulation (RC) drilling for grade control sample collection was selected by the Pueblo Viejo Mine Geology department at the recommencement of the operation in 2010. This method was selected because it allows: for multi-bench drilling (60 m hole depth, four benches of mining) to aid mine planning and provide a detailed close spaced drill data comparison with the reserve model angled drill holes to optimise the drill hole interception of the vertically controlled mineralisation dry sample collection in areas of excessive surface and groundwater mining operations to commence with the long assay return period (due to the need for the samples to be shipped overseas for analysis) until the on-site laboratory is operational.To date, 118 302 m of drilling has been completed throughout the operations of two open pits: Monte Negro and Moore. Two drill rigs (contractor and site-owned and operated) with three generations of sampling systems have been used to date. Throughout the drilling a 20 per cent quality assurance, quality control (QAQC) sample check (blanks, field duplicates and standards) have been used to check the drilling and laboratories performance. In addition, a total of 1104 fines samples were collected to compare the drill chip samples collected and the fines lost with two of the sample systems used.The drilling to date has highlighted the need for a complete and coordinated system to be used before sufficient confidence in the quality of the samples collected is achieved.The complete system must be set-up and coordinated to obtain the best quality sample possible. This complete package includes: drill bit size and shape for the rock being drilled and mineralisation targeted face sampling hammers with the correctly sized hammer shrouds sample hose routing to reduce sample flow turbulence and choking blow-down valves to eliminate drill hole water that has entered the drill string during rod changes correct drilling techniques targeting sample quality a sample system that captures the fines for inclusion into the sample.These improvements can be obtained without reducing the drilling rates.The measurements required to demonstrate the improvement in the sample quality will be the focus of future work within the department.CITATION:Goers, M and Almond, M, 2012. Bit to bag - The importance of a total coordinated system in reverse circulation drilling, in Proceedings Sampling 2012, pp 65-72 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By A Woodley, G Keir

The mining industry faces concurrent pressures of reducing water use, energy consumption and greenhouse gas (GHG) emissions in coming years. However, the interactions between water and energy use, as well as GHG emissions have largely been neglected in modelling studies to date. In addition, investigations tend to focus on the unit operation scale, with little consideration of whole-of-site or regional scale effects.This paper presents an application of a hierarchical systems model (HSM) developed to represent water, energy and GHG emissions fluxes at scales ranging from the unit operation, to the site level, to the regional level. The model allows for the linkages between water use, energy use and GHG emissions to be examined in a flexible and intuitive way, so that mine sites can predict energy and emissions impacts of water use reduction schemes and vice versa. This paper examines whether this approach can also be applied to the regional scale with multiple mine sites.The model is used to conduct a case study of several coal mines in the Bowen Basin, Australia, to compare the utility of centralised and decentralised mine water treatment schemes. The case study takes into account geographical factors (such as water pumping distances and elevations), economic factors (such as capital and operating cost curves for desalination treatment plants) and regional factors (such as regionally varying climates and associated variance in mine water volumes and quality).The case study results indicate that treatment of saline mine water incurs a trade-off between water and energy use in all cases. However, significant cost differences between centralised and decentralised schemes can be observed in a simple economic analysis. Further research will examine the possibility for deriving model up-scaling algorithms to reduce computational requirements.CITATION:Keir, G and Woodley, A, 2013. Regional trade-offs between mine water and energy use - a water treatment case study, in Proceedings Water in Mining 2013 , pp 21-28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By I Sucholutsky, D M. First, D Mogilny, F Yusufali

Machine learning is creating value in all facets of the mining industry, from exploration to production. The authors provide an accessible, high-level introduction to artificial intelligence (AI), machine learning (ML), and deep learning (DL); the latter being widely recognised as one of the most powerful forms of ML. In particular, the authors will introduce deep learning models known as convolutional neural networks (CNNs), how they are applied, and the economic considerations necessary for determining when DL may be the right solution to de-risking complex block modelling problems. The authors present preliminary results from the mineral resource modelling study of the Jundee orogenic gold deposit, Yandal belt/gold province, Western Australia. The primary goal was to identify the direction and location of the narrow gold veins more accurately and demonstrate how non-linearly correlated elements are used as direct inputs to the resource model to assist with the target element’s grade prediction. This demonstrates that: (1) existing techniques for finding correlations between assayed elements do not adequately reflect the complex geology of the asset, (2) nonlinear correlations that are difficult to model as simple mathematical functions are representative of geological patterns in a deposit, and (3) non-linearly correlated assayed data, fed as inputs, increase the performance of the resource model as reconciled through blind tests. To conclude, the authors hypothesise that the patterns represented by the DL block models may be revealing the results of overprinting geological processes that generated mineral deposits. For example, the primary hydrothermal processes that deposited metals created depositional patterns that become particularly complex as a result of being overprinted, in part or in whole, by secondary physicochemical processes. This may explain why non-linear geochemical relationships have the capacity to generate more accurate block models of mineral deposits.

May 24, 2023

By F Saloojee, F K. Crundwell

Refractory ores need to be pretreated prior to cyanide leaching for acceptable gold recovery. Pressure oxidation is one method of rendering the ores more suitable for cyanidation. The focus of this work is optimisation of autoclave configuration for pressure oxidation. An autoclave for the pressure oxidation of a feed containing pyrite and arsenopyrite was modelled, using the population balance framework. The autoclave model takes into account feed particle size, reaction kinetics and retention time. Mass balance calculations were incorporated into Cycad Process« software. This allowed for the investigation of different circuit configurations. The base case model consists of a single autoclave. The feed was then doubled and additional autoclaves were added to provide the same residence time as the base case. Four different configurations for the additional equipment were simulated. These were parallel, series, series with inter-stage thickening and parallel-series circuits. The options are compared in terms of extraction and productivity. The parallel circuit behaves similarly to the base case. The series and series-parallel circuits have higher recoveries and productivities than the base case. The series circuit with inter-stage thickening provides the highest extraction and productivity. This is because the thickening reduces the slurry volume and increases the residence time of the solids in the downstream autoclave.CITATION:Saloojee, F and Crundwell, F K, 2013. Optimisation of circuits for gold pressure oxidation, in Proceedings World Gold 2013 , pp 181-188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Bell I. F

In 1985, ZC Mines (now Pasminco South) had been unprofitable for some years due to a combination of high operating costs, low metal prices, low head grade and an aging and inadequate mining infrastructure. However, the resource of metal in the ground was still of world class, even after some 80 years of mining. A major study, which was to be of two years duration, was therefore commenced to establish a practical and profitable long term mining strategy and to cost the infrastructure options needed for its support and thus form the justification for a capital expenditure program to take the mine profitably into the 21st century and its second century of operation. This paper discusses the rationale behind the methodology adopted and the nature of the results achieved in one aspect of the study - the determination of the mineable resource and the relationship between the head grade/quantity of the economically mineable resource and the variables of cut-off grade, cost structure, annual production rate and metal prices/exchange rates. The basis of the study was the designing of some 5000 scopes to mine out the entire resource for a range of cut- off grades and the assembly of the detailed physical data thus obtained in a stope-by-stope data base for financial and other analysis. Those scopes which were shown to be economically mineable were then scheduled for two optimum annual production/cut-off grade/metal price combinations to provide life-of-mine cost and value of production cash flows.

Jan 1, 1992

By D J. Brake

In most underground mines, the ventilation system is a significant portion of the total mine capital and operating cost and the largest consumer of underground electrical power. The effectiveness of the ventilation system has a major bearing on the safety, health, comfort and morale of underground personnel, and has a critical role in meeting production targets and therefore business revenue. Perhaps the most important component of the primary ventilation system is the primary fan. Correct performance testing of the primary fan during the warranty period is important not only to ensure the mine has obtained the asset that it paid for and can therefore deliver on the fanÆs crucial safety and economic role in the future of the mine, and to provide a justification for releasing final performance warranty payments to the supplier, but also to provide a benchmark or baseline against which to assess future performance issues. As there are at least three potential international standards available to measure fan performance, there has been considerable confusion regarding which of these to use for testing primary mine fans, and also the correct allowances and tolerances to use. This paper provides guidance on which standards to use for different applications, how the standards should be interpreted, what allowances and tolerances are reasonable, and other important issues to be resolved with the fan supplier prior to making a contract award. The paper also discusses practical issues and methodology for in situ primary fan performance testing.CITATION:Brake, D J, 2013. Performance and acceptance testing of main mine ventilation fans, in Proceedings The Australian Mine Ventilation Conference , pp 141-148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By H Kurth

High specification Prompt Gamma Neutron Activation Analysis (PGNAA) has been successfully applied to conveyed flows at iron ore operations since 2002 to representatively measure ore quality for improved quality management and process control. While the PGNAA technique has changed little since that time, significant improvements have been made in measurement capability. Elements previously unable to be measured well or at all using this technique are now measurable and one of these is phosphorus. Aluminium and magnesium are also key elements in addition to calcium and silicon in determining sinter basicity in ironmaking. Other elements measured routinely in iron ores include iron, carbon, potassium, sulfur and manganese. The benefits of representative measurement cannot be overstated as iron ore mining operations in South Africa, Europe, Australia, Asia and the Americas have discovered. The technology is applicable to any conveyed flow where elemental analysis in real time assists with quality management, from raw materials in ironmaking through to scrap steel in steelmaking and coal quality for coke-making. Major benefits are realised when raw material processing is optimised and this often includes diversion of material meeting a required quality so it can bypass unnecessary processing. This includes waste rock which can be diverted from a plant feed stream in 30 sec increments or ore that meets product quality being diverted to bypass beneficiation. Analysers are successfully utilised to identify ore types that assist with upgrade optimisation in jig plants; measuring feed, product and discard flows to also account for metal content. Product flows to stockpiles help manage production flows and stockpile qualities for different products and assist in blending ores into trains or ships to confirm specification compliance. Technologies can be used in magnetite processing but are predominantly used in hematite and goethite ore processing operations. The paper details examples of the above applications at various operational sites providing estimates of economic benefit as well as operational improvements.

Sep 18, 2023

By G Le Juge, K Waldock

The current suite of bulk mining explosives has been available to the industry for over 20 years. The flexibility and performance of ammonium nitrate based emulsion blend explosives were accepted by the mining industry in the early 1980s. These water resistant explosives rapidly displaced the water gels and slurries developed during the previous two decades. However, since the 1980s there has been no equivalent step change to the basic formulation or application of bulk explosives, although there has been a continuous process of refinement with respect to stability, handling characteristics and most significantly, cost. In the 1980s explosives supply contracts were awarded based on technical evaluations, usually accompanied by field trials. Technical personnel from both mining companies and explosives suppliers dominated the negotiations and there was a strong focus on explosive energy and blasting requirements. Today, explosives from alternative suppliers are difficult to differentiate on the basis of energy so the focus has shifted to aspects of service and price û bulk mining explosives are now largely treated as a commodity and the negotiations are dominated by commercial personnel. Commercial pressures from large mining companies have seen a substantial reduction in the real price of explosives. However, this has come at a cost. In order to reduce manufacturing costs, emulsion formulations have changed. In general they are not only cheaper, but also less energetic. Powder factors have had to increase to achieve the same blasting results, especially in hard ground. It is debatable whether the mining companies have achieved all of the economies they were seeking. This paper discusses these issues and argues that the mining industry would benefit from taking a more technically driven approach to meeting their blasting requirements. Recent trends towards more open contracts between the mining companies and their suppliers can be extended to explosives. To achieve this, mining companies will need to acquire sufficient technical knowledge to take a more pro-active approach to specify the characteristics of the explosives required to maximise the economic performance of their operations.

Jan 1, 2004

By M A. Vinokurova, V M. Mullov

Due to treatment of refractory carbonaceous low-grade gold ores a new technology providing improved precious metal recovery is required. For this reason, a technology including gravity, flotation, recleaning of the flotation concentrate, intensive cyanidation of the gravity concentrate and carbon in leach (CIL)-process for intensive cyanidation tailings and the recleaned concentrate was developed. The proposed technology allows to decrease preg-robbing activities of concentrates treated by subsequent cyanidation. Total gold recovery by the proposed technology from the ore with a head grade of 0.8 g/t was 83.9 per cent. The gold loading onto the activated carbon from CIL process was 6.500 g/t.

Jan 1, 2007

By B Besa, E K. Chanda

It has long been recognised that narrow vein mining needs innovative approaches to mine access and mining methods in order to improve the economics of this vital part of the mining industry. The mining equipment used currently requires large openings in narrow vein-type deposits making mining operations uneconomical. In view of this and other shortcomings of the current mining practices, a study was initiated to investigate the potential of using low profile electric loader with mounted conveyor in conjunction with the electric monorail haulage system (EMTS) to load and haul the blasted material, particularly in decline development and main haulages. Computer simulation based on the General Purpose Simulation System/Henrikson (GPSS/H) is used to model the system and evaluate its performance. The results are compared with those for conventional mining using trucks and loaders. The EMTS provides competitive haulage rates in substantially smaller excavations than is currently achievable. According to simulation results, the electric loader in conjunction with the EMTS had the same number of blasts as the conventional system and hence the same advance rate of 3.33 m per 12 hour shift. Furthermore, the total drill-blast-load-haul cycle time was less than the conventional system by one hour.CITATION:Besa, B and Chanda, E K, 2012. Evaluation of low profile electric loader in conjunction with electric monorail haulage system in narrow vein mining, in Proceedings Narrow Vein Mining 2012 , pp 221-228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

A research and testing facility has been developed at Simtars to allow the spontaneous combustion testing of coal on a large scale. In this adiabatic reactor, the coal particle sizing is closer to that which could be found in the goaf and therefore the reaction is more likely to simulate the underground situation. This allows aspects of the spontaneous combustion process and methods for detecting a heating to be investigated which cannot be done in an operational mine. Up to 18 tonnes of run of mine or crushed coal is loaded into the reactor and allowed to self-heat while the temperature and gas profiles within the coal pile are monitored. The gases evolved from the coal are analysed using a fixed gas monitor system and gas chromatography to determine which of the common mine fire indicators and ratios can be used to predict the onset and progress of coal heatings. Benchmarking of the inherent propensity of a coal to spontaneously combust at both the large- and laboratory-scale is also possible by comparing the sample against previously tested samples. It has been found that the coal particle size affects both the time it takes for the coal to react and the location of the developing heating. The heatings generate approximately one metre from the inlet but in the crushed coal case do not progress to an advanced heating stage until the æhot spotÆ migrates towards the coal surface where there is an increased oxygen supply. Physical properties such as the compressive strength of the coal also affect the heating size and the time it takes for a heating to develop. Higher strength coals appear to oxidise more slowly and therefore take longer to self-heat as oxidation of the coal is the heat-generating step in the spontaneous combustion process. The best indicators of the state of the heating were found to be CO make and GrahamÆs ratio which are independent of air flow. Investigation of a potential spontaneous combustion should begin as soon as the CO make or GrahamÆs ratio exceed the background levels. The results from the tests undertaken on a number of Queensland and NSW coals are reported here together with the implications for the mining industry.

Jan 1, 2005

By Faidel VV, Yushina TI, Yagodkina NG, Yatsimirsky AK, Chanturiya VA

Among the problems of the flotation of sulphides by the thiol collectors is the dependence and varieties of the flotation starting with the time and oxygen contents in the slurry. For sulphides, the flotation stage follows after the electrocatalytic oxidation of the collector with oxygen on the surface of the conductor minerals. The necessity of the oxygen for sulphide flotation (Plaksin and Bessonov, 1957) is in accordance with a corrosion model of a collector surface sorption (Salamy and Nixon, 1954). As Golikov and Nagimyak (1961) showed, the sulphides possess catalytic activity which provides the autoxidation of the xanthates in the sluny to the dixanthogen. This stage can be rather protracted, which limits the speed of the total process. Disulphides constitute important collectors for the sulphide flotation and the optimal degree of the xanthate oxidation is about 20 per cent for different ores (Abramov, 1978) or, following Chanturiya and Nazarova (1977) the surface compositions for various sulphide ores are different and an optimal oxidation degree is variable from five to 25 per cent according to the ore nature. The optimisation of the surface composition is possible by application of the dixanthogens, or by a partial chemical, electrochemical, or catalytic oxidation of xanthates (Desains, 1847; Schall, 1896; Vigdergauz, 1989). According to Rand (1977) and Vigdergauz (1991) sulphides possess different catalytic activities for oxygen electroreduction. In neutral solutions, for example, the following decrease in the order: FeS2 (Fe,Ni)9S8 CuFeS2 FeS; Cu5FeS4 Cu2S; PbS (Vigdergauz, 1991). For the cases of low catalytic activities of the sulphides, the preflotation oxidation of xanthate could be useful to optimise the process kinetics.

Jan 1, 1993

By G R. F Alvear Flores

Mineral resources are becoming more complex in composition and structure making it more difficult to produce clean concentrates for primary metal smelting. In parallel, providing technological solutions to the recycling and recovery of end-of-life materials is becoming more important in moving towards the goal of increasing circularity. The availability of fundamental thermodynamic data and advanced thermodynamic tools greatly assists in evaluating these complexities and their impact on existing and new processes. In addition, it is fundamental to support the economic performance of smelters. This paper describes several examples on how fundamental work can be applied to industrial processing..

Jun 17, 2024

By K T. Mandisodza, T J. Cartledge

The principal objective of Geotechnical Engineers supporting operating mines is to provide safe working conditions and ensure that pit designs are geotechnically optimised to site conditions and pre-defined stability requirements. Pit slope designs are delivered in advance of pit excavations. Making changes to these designs is usually slow to enact and involves a layered sign-off before implementation, leading to unwanted delays in their adoption and subsequently increased production pressures. When unexpected ground conditions are encountered during the mining process, or short-term mining schedule requirements demand it, changes to these designs may not be easily feasible in certain situations. It is when these scenarios arise that Geotechnical Engineers need to be proactive and consider unconventional options to deliver safe operating conditions while satisfying short-term requirements to the mine schedule. Essentially, the geotechnical short-term strategic designs double-pronged approach supports the mine schedule while providing safe conditions and minimising geotechnical risks for people and equipment. Common short-term strategic geotechnical designs include; slope buttressing, over-steepening cut slopes to increase reserve recovery through unplanned or emergency cutbacks, and accepting risk threat and operating under unstable slopes. When implementing strategic design options, the Geotechnical Engineer must consider the broader implications for such designs. They must think of the plan’s long-term effects on the mine schedule and pit wall stability. Initiating aggressive designs to recover additional reserves to satisfy a short-term scheduling demand could result in-pit wall instability or suboptimal pit layout. Before and during the implementation phase, the Geotechnical Engineer must communicate and engage with relevant stakeholders to ensure that the plan is executed accordingly and geotechnical risks are effectively managed. Proactiveness to ground response and implementation of risk management strategies will improve safety performance and optimise mining schedules.

Jun 22, 2022

By M Wieloch, D Wimpenny, M Chappell

Fibre-reinforced geopolymer concrete (FRGC) contains no Portland cement or steel reinforcement, but instead uses synthetic fibre reinforcement and a geopolymer binder. The use of geopolymer binder in lieu of Portland cement reduces the concrete’s embedded energy (CO2 emissions) whilst the use of synthetic fibres eliminates the issue of reinforcement corrosion, thus enhancing the overall long-term durability of concrete. This paper presents the development of FRGC during a three-year project funded by the Victorian Science Agenda and a consortium of five organisations. The work involved laboratory and field trials and the production of prototype tunnel segments that have been subject to durability and fire testing.FRGC has exceeded the performance of the Portland cement-based control mix in terms of flexural strength, chloride diffusion, water sorptivity and drying shrinkage. Furthermore, the FRGC segments subjected to a simulated hydrocarbon fire test did not exhibit explosive spalling; however, the creep of FRGC was approximately three times that of the steel fibre-reinforced Portland cement-based control mix. The compressive strength and tensile splitting strength of the FRGC were also lower than the control mix. These differences need to be allowed for in the design using FRGC.Prototype bolted tunnel segments of up to 0.8?t mass have been produced from FRGC using standard production techniques and ambient curing. These were successfully produced within a 24-hour production cycle. Cut sections through the segments showed good compaction and even distribution of fibres. The estimated carbon footprint of tunnel segments produced using FRGC is approximately 70 per cent less than that of Portland cement-based segments containing 25 per cent fly ash and steel reinforcement.The results to date indicate that FRGC has the potential to produce a new generation of tunnel segments and, in general, precast concrete products with increased durability and substantially reduced carbon emissions compared to the Portland cement-based concrete with steel reinforcement.A summary of further research carried out by CH2M HILL into a complete elimination of ferrous inserts from segmental concrete tunnel lining is also summarised in this paper. The use of non-ferrous connectors for radial joints in combination with the FRGC technology in the manufacture of tunnel segments will effectively lead to development of a new generation of segmental tunnel lining systems.CITATION:Wimpenny, D, Chappell, M and Wieloch, M, 2014. Fibre-reinforced geopolymer concrete – an innovative material for tunnel segments, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 345–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J M. Santini, I C. A Streimann

Arsenic is a naturally occurring element in the environment and is toxic to biological systems. Arsenic can exist in the environment in the following redox states, arsenite (+3), arsenate (+5), arsine (-3) and elemental (0) (Oremland and Stolz, 2003). Arsenic is released into the environment by natural and anthropogenic activities such as rock weathering and ore mining, respectively. Such activities result in the release of the soluble inorganic arsenic oxyanions, arsenite and arsenate. The redox state of arsenic in the environment is influenced by a number of factors including, redox potential, pH and microorganisms (Irgolic et al, 1977; Genc-Fuhrman, Tjell and McConchie, 2004). Recently, the ability of microorganisms to influence the cycling of arsenic in the environment has attracted much attention. Microorganisms that can oxidise arsenite and reduce arsenate have been isolated and the mechanisms of arsenic metabolism are currently being investigated. The differences between arsenic resistance and arsenic metabolism are being revealed. The role of microorganisms in the release of arsenic into the environment is of particular importance with arsenic contamination of waters causing the death of millions of people worldwide, due to the consumption of contaminated water (Vasken Aposhian et al, 2003; Islam et al, 2004).

Jan 1, 2004

By H Benzer

Grinding clinker to finished cement consumes more energy than any other comminution process. World production of cement in 2009 was 2840 million tonnes and the energy required for comminution was 40-60 kWh/tonne depending on the clinker characteristics and the fineness of the finished cement. Machines used include single and multi compartment ball mills, HPGRs, vertical roller mills, centrifugal air separators, V separators, screens and crushers. The circuit most commonly used consists of a closed circuit HPGR followed by a single compartment ball mill and an air separator, and in operation the variables are adjusted to obtain maximum throughput with no loss of quality of the separator fines.A common objective in cement plants is to reduce energy consumption without affecting the particle size in the finished cement and simulation is used as one procedure to achieve this. Models are now available for all the machines commonly used in clinker circuits and circuit optimisation studies using simulation have been carried out in many plants leading to decrease in energy consumption per tonne of cement. In this paper the models used will be discussed briefly and several case studies will be reviewed which will highlight the effect of change in ball size in a two compartment mill, the role of the HPGR in an HPGR – ball mill – air separator circuit, and the use of a high intensity vibrating mill for producing finished cement with high additive ratio.

Aug 8, 2011

During the 1950's there was a flurry of activity on the design of main ventilation shafts for mines. More recently, a new ana- lysis was commissioned in relation to the multi-shaft, nuclear waste isolation facili- ties currently under design in the United States. This paper presents the major find- ings of that study and should prove of value as a reference in the design of proposed new shafts. An overview of mine shaft resistance introduces the effects of the shaft walls, fittings, conveyances and shaft stations. Each of these is analyzed in turn. A com- pletely new technique is described, which facilitates the estimation of wall resis- tance. The effect of size of a conveyance is quantified and shown to be dominant when the cage occupies more than 30 per cent of the shaft cross-section. The dynamic effects of a moving conveyance are also analyzed.

Jan 1, 1988