Search Documents

Magnetic separation using particle rotation in a continuously rotating magnetic field offers very low to insignificant non-magnetic particle entrapment, and precise magnetic fractions. The precision of rotating magnetic field separations makes the method ideal for dry laboratory magnetic analysis work, where conventional laboratory magnetic separators can give misleading or uncertain data. The very low entrapment characteristics make the method ideal for entrapment-critical separations within the diamond exploration industry or in gold recovery. A single wet rotating magnetic field (RMF) unit is able to achieve a cleaner separation (at similar or better recovery rates) than a three-stage separation using conventional wet drum separators. The RMF separator is able to work effectively at particle sizes below 50 ¦m, and RMF separation could, at least in theory, be used down to single domain particle sizes. Rotating magnetic field (RMF) separation is carried out by magnetically spinning the particles at frequencies up to 300 Hz. The particle rotation itself may be used to roll the particles out of the separator. At angular velocities of 100 Hz, magnetic flocs are unable to form, and any entrapped particles are energetically expelled. In an RMF separator, the outer drum can be stationary while the inner magnet rotor rotates, allowing, for example, the injection of cleaning water underneath the separating magnetics to help remove small suspended non-magnetic particles.

Jan 1, 2000

By Spottiswood DJ, Kelly EG, Bull WR

An empirical model of a 254mm water-only cyclone treating minus 17001im coal has been developed. The model includes the prediction of by-passing, SG50 corrected, water split and the use of a single equation forthe reduced performance curve of particles in the range 1700-106pm. Particles finer than 106pm did not separate according to specific gravity. Simulations using the model showed the water-only cyclone performance to be dependent more upon feed size distribution than washability when the feed contains high-ash fines, but that, with a deslimed feed, the yield and ash content of the over-flow should be controllable by altering feed rate or feed pulp density.

Jan 1, 1985

The development of the Australasian Code for Reporting of Identified Mineral Resources and Ore Reserves is a significan step towards informing the financial community and the public about the future profitability and risks of investing in resource companies. The Code is also important from the accountants' point of view because it provides them with a well-defined bash for assigning costs or attributing value to the assets of resource companies and hence improving their financial reports. Although reporting to the public is ultimately the responsibility of management, accountants, like geologists, are frequently required to provide information for inclusion in these reports. Jr the last ten years, there has been a considerable refinement in the reporting of mineral resources which can be attributed mainly tc the progress made towards developing the Code. It seems tha the classification and terminology that the geologists have developed are widely used in the annual reports. However, little progress has been made by accountants in improving the financia information. The purpose of this paper is twofold: (a) to outline briefl) some of the major problems in accounting and reporting fo; mining companies and; (b) to examine the potential contribution of the Code in solving those problems.

Jan 1, 1990

The introduction of new technology into thegold-mining industry has been encouraged in recent years by increases in the price of gold andthe necessity for costs to be contained.At most new gold mines, run-of-mine millingis preferred over crushing and multistage milling, and this change at the head of the circuit leaves no place for the manual sorting of ore and for gravity concentration in the mill circuit.Flotation continues to hold its place in goldrecovery. However, a decline in the demand forsulphuric acid may limit the amount of pyrite thatcan be roasted before cyanidation.

Jan 1, 1984

By Propster M, Choudhry M

THIS note gives comments on the paper by Kitaev et al on p. 68 of this book and compares results with those obtained by ourselves. We wish to say that the authors are to be congratulated on their sophisticated approach to an important problem and that it complements our efforts on flow maldistribution.1-5 It is our view that Eqs. (1)-(5) on p. 69 are impressive, but unfortunately with present day computers and computational facilities, it would be quite impractical to contemplate the numerical solution of these. Eq. (8) in the authors' paper, on p. 70, does provide the logical starting point for tackling flow maldistribution problems and strictly speaking this equation is more accurate than Eq. (1) in our paper in this book. We note in passing that there is direct experimental evidence to support the contention that our Eq. (1) is at least a reasonable approximation and one may question in a practical sense whether the refinement afforded by Eq. (8) in the paper by Kitaev et a/ is justified. While one must readily accept the appropriateness of Eq. (8) of Kitaev et al as a starting point, the subsequent mathematical manipulation by the authors is open to serious criticism. In order to solve this complex, non-linear equation Kitaev et al postulated irrotational flow, which afforded considerable simplification. One can argue simply on physical grounds that the assumption of irrotational flow is inappropriate, a fact which should be readily apparent on inspection of the flow fields shown in Figs. 2 and 3 of Kitaev's paper. It follows that while the starting point through the use of Eq. (8) is correct the results derived from this starting point may be suspect because of the erroneous nature of the irrotational flow assumption.

Jan 1, 1975

By Selischop F, Tredoux M

The distribution of platinum-group elements (pGEs) has been investigated in matte and slag samples from Waterval Smelter (Rustenburg Platinum Mines). The study showed that a strong preference of PGEs for alloy phases in matte represents a concentration mechanism that commenced in the furnace but can be considered a continuum from natural processes. Metal losses to fayalite (converter) slag occur by matte entrainment due to the mechanical capture of liquid sulphide droplets from the matte layer, and the exsolution of dissolved metal sulphide resulting from changes in the oxidation state of the slag. The latter is comparable to immiscible sulphide in basic magmas. However, the observed distribution of PGEs shows enrichment in metal phases of the matte. A mechanism is proposed whereby naked PGEs in silicate melts coalesce to form clusters which are stabilised by surface attachment of sulphur atoms. This envelope acts to 'draw the cluster into sulphide melts. Small particle melting effects permit PGE clusters to remain as liquids at magmatic and smelter temperatures.

Jan 1, 1994

By Ehlert G, Steinlechner E

The paper describes a new process for filtration which combines the continuous operation of conventional vacuum filters with the low final moisture contents hitherto only achievable with plate and frame presses. The increasingly high portion of fine particles causes several problems in the filtration of copper concentrates. One drawback is that remarkable quantities of liquid are attached to the very fine particles because of their specific surface area. Furthermore, fine particles also reduce the size of the capillaries in the filter cake, thus increasing the critical pressure which any filtration system has to exceed to achieve the desired final cake moisture. The maximum filtration pressure of conventional vacuum filters is limited by nature itself and by practical aspects to approximately 0.75 bar. The hyperbaric filter combines the continuous operating principle with an increase in filtration pressure of up to 6 bar simply by placing the entire disc or drum filter inside a pressure vessel. The major machine components and process features are explained in the details of the paper. After extensive research and field testing, 23 ANDRITZ hyperbaric filters, with a total filtration area of 1968 m2 have now been sold. Seventeen of these units (1440 m2) are in commercial use and more units are, on order. Performance data on copper concentrates from plants in Australia, South America, Poland, Africa and North America are outlined in detail. Compared to vacuum filters, generally hyperbaric filters will reduce the final cake moisture of concentrates with 75 per cent

Jan 1, 1993

By Roddick F

From its mining lease at the northern end of Cohens Reef at Walhalla in the North Gipps- land mountains, the Long Tunnel Extended Gold Mining Company produced 13,695kg of gold, which at 1982 prices represents a value of about $140 million. In the period 1885 to 1908 the mine was one of Australia's principal reef gold producers, being top Victorian producer in six of these twenty-four years. Prior and subse- quent occupants of the lease produced an addit- ional 160kg of gold. The Extended and the other mines on Cohens Reef whilst contributing importantly to the financial resource of Victoria, were the sole important support for the substantial town of Walhalla that had grown up around them. When the mines closed, Walhalla gradually reduced from a bustling developed town to the present attractive mountain village so favoured by tourists.

Jan 1, 1982

Previous studies on the blast furnace raceway zone have been undertaken at three levels of scale, namely: laboratory models at low temperature, hot models which simulate coke combustion in the zone, and tests performed on operating and dismantled blast furnaces. This paper reviews the results of this published work on raceways in order to illustrate the factors which affect the raceway shape, size and combustion characteristics. As a result of the work it has been established that raceways are influenced by blast parameters such as velocity, temperature and chemistry, as well

Jan 1, 1981

By Lama R. D

The Australian underground coal mining industry is undergoing major changes. This paper analyses the technologies presently being researched in mines, and discusses their utilisation as major contributors in the underground mining of coal in Australia over the next 20 years. It describes the problems that underground mining of the year 2000 will face and the possible solutions to those problems based upon results of present day research. Methods, equipment and organisational requirements are outlined. Developments in micro-electronics, computerisation and monitoring will require a new look into human resource development, education and training, and organisation to meet the challenges of the 21st century. The mining system's philosophies of the future are Outlined.

Jan 1, 1986

By Denby B

The ever increasing demand on land use has led to large areas of land being considered for development, which because of past mining activities are covered by substantial depths of fill materials. This paper examines the problem faced with the development of land infilled with open cast mining backfill, in predicting the behaviour of the fill upon development. To be able to design foundations suitable to withstand the movements that occur within open cast backfills or design a backfilling operation that produces land suitable for a proposed after development, a means of predicting backfill settlement is required. Factors critical to this prediction are the timing of backfilling operations, the compactive state of the backfill and the inundation of the backfill. The analysis of a considerable quantity of data collected from the monitoring of backfilling operations and backfill movement at a range of open cast coal sites located within the UK has given the authors a better understanding of how open cast backfills behave in terms of long-term creep settlement, collapse settlement and how these are effected by backfill scheduling. This knowledge has been encoded into a program running under Microsoft Windows that enables a user to make settlement predictions for a point, a given section or area or for the whole site. Differential settlements, critical to any development design, can also be determined between any two points taking into consideration the heterogeneous nature of open cast backfills. The program was tested with data from an open cast coal site in the UK. Compaction monitoring during the placement of the backfill material enabled a model of the backfill to be constructed taking into account backfill properties and scheduling. This model, taken as input into the program, enabled future backfill settlement predictions to be made. A comparison is given between these results and actual settlements obtained from a short-term settlement monitoring scheme.

Jan 1, 1995

By Aspinall T. O, Bell L. C

Increased awareness and stricter enforcement of regulatory requirements for adequate rehabilitation of surface mining sites has made environmental planning an essential part of strip mine planning. Rehabilitation is site specific and should be based on data which relate to that site. Cost-effective spoil pile design to minimise erosion is an important part of rehabilitation. Spoil pile design is an integral part of strip mine design. QCT Resources Limited has provided a postgraduate scholarship toward research in this area. The controlling factors of spoil pile design are post-mining land use, drainage requirements and degree and rate of erosion. The extent to which mine design is controlled by these factors is determined by regulatory requirements. To plan acceptable rehabilitation programs, erosion processes must be accurately modelled, and a range of erosion prediction models are available. Useful prediction models can be placed in two categories with the first category containing soil loss prediction models which can be used to predict the amount of soil lost from an area over a short or long term basis. Models in this category include the Universal Soil Loss Equation (USLE), Water Erosion Prediction Project (WEPP), Griffith University Erosion and Sedimentation System (GUESS) and Chemical, Runoff and Erosion from Agricultural Management Systems (CREAMS). The second category contains topographic evolution models which give an indication of the long term morphological development of a formed surface subjected to erosion processes. Models in this category include "Topog", Willgoose's Physically Based Catchment Evolution Model and Areal Nonpoint Source Watershed Environment Response Simulation (ANSWERS). The USLE has been used in the agricultural field for soil loss prediction. To apply the equation to mine sites in Central Queensland, it is necessary to understand the factors affecting erosion at the sites. This understanding should allow the variables of the equation to be quantified. The rainfall factor applied in the USLE is independent of engineering design or soil management techniques. The factor of spoil erodibility is dependent on the material's physical and chemical properties and can vary from site to site. In the equation, the topographic factor, cover and management factor and conservation practices factor can be varied by design to reduce erosion on rehabilitated areas.

Jan 1, 1991

The standard charge weight scaling laws imply that only one particular delay (that possessing the maximum instantaneous charge) contributes to the ppv. However, the present analysis clearly demonstrates that a varying number of blastholes contributes to the ppv. This number also increases with distance, x, between the blast source and the detector, and is caused by waveform broadening due to attenuation. Thus the operative charge weight, itself, is also a function of the distance, and so makes the standard charge weight laws difficult to implement. If the delay time scatter is neglected, then, under certain conditions, relatively simple expressions can be derived for the ppv magnification, FN, as a function of the number, N, of blastholes. When the influence of delay scatter and random fluctuations in each blasthole vibration is included using Monte Carlo simulations, then, to a first approximation, the condition FN=KNx applies, where KN is a constant dependent upon N. Unfortunately, however, for any particular blast this condition cannot be distinguished from the standard charge weight scaling law. The dependence of ppv on N would only be apparent if blasts of differing N were to be compared in an otherwise identical environment. Since this situation is very difficult (if not impossible) to realise, then the influence due to N, although significant, goes largely undetected. Another problem associated with standard charge weight scaling laws is the difficulty of accurately assessing the appropriate charge weight, even if attenuation broadening is neglected. For example, if a number of blastholes are very close, then they experience a vibration interaction which is non-linear. However, if the same blastholes were to be widely spaced, then the separate vibration signatures add linearly. The standard charge weight scaling law fails to distinguish between such linear and non-linear regimes. Unfortunately, in many production blasts, both regimes exist throughout various portions of the blast spatial pattern and so makes it difficult to determine the operative charge weight. The solution to the combined influence of waveform broadening and linear/non-linear interactions will obviously require substantial future research. A possible solution may be found in the use of numerical dynamic codes.

Jan 1, 1990

By Romanovsky N. P

The Pacific Mobile Belt (PMB) is characterized by old origin and complex evolution both in time and space. As the global structure, the PMB is a narrow tectonic region dividing two plan-etary hemispheres, viz. the Pacific and IndoAfro-Atlantic ones, the relative shifting of which defines the character of many geodynamic processes in this belt. The PMB features inhomogeneity of structure, special matter composition characteristics, sharply broken-out topography, and intensive fields. Generalized anomalies of the gravitational field closely correspond to the PMB boundaries defined by the real features, i.e. the andesite line and distribution areals of Mesozoic-Cenosoic granitoids. The belt boundary position is controlled also by seismic velocity anomalies at a depth of down to 200 km. The modern PMB deformation is defined by the left-hand equatorial shift and rotation of the Pacific Ocean counterclockwise. This rotation is non-uniform in time and of an oscillating character. The motive forces of the phenomenon are considered.

Jan 1, 1990

By Barnes GJ

The gabbroid-hosted nickel sulphide deposits of the East Kimberley constitutes one of Australia's most prospective emerging nickel provinces. Sally Malay Nickel NL (SMN), a wholly owned subsidiary of Gindalbie Gold NL, has established the East Kimberley Nickel Project (EKNP). The EKNP project tenements cover about 2000 sq km. The tenements cover the northern potion of a corridor containing mineralised or potentially mineralised layered mafic-ultramafic intrusions which includes the Ni-Cu-Co sulphide deposits at Sally Malay and Keller Creek. The Sally Malay deposit is located 225 km south-south-west of Kununurra (Figure 1). The sealed Great Northern Highway passes 3 km to the east of the deposit.

Jan 1, 1996

By Chenggang W, Junhua D

Fragmentation variation laws in loading and non-loading areas are obtained by cement block model blasting experiments under various stemming lengths. A reasonable ratio between loading length and stemming length is worked out according to minimum average fragment size. The present continuous loading structure, for its very long length to be stemmed, leads to insufficient fragmentation in the upper part of bench. So a new loading structure with bottom air cushion is put forward. The author analyzes blasting effects and processes of two loading structures' and proves that there exists a optimal length of air cushion.\

Jan 1, 1990

By Costello MC

An alternative process for desorbing and recovering metals from activated carbon has been developed, and is the subject of several patent applications by Micron Research (W.A.) The system uses the principle of conditioning the carbon in a strong alkaline cyanide solution followed by distillation desorption in a fractionating column, using the carbon as the column packing and methanol as the desorbing agent. The system offers the following advantages : (a) The processes of desorption, methanol recovery and reactivation are all carried out in a single column with the carbon itself acting as the column packing. No other desorption plant items or fractional distillation equipment are required. (b) The metal values are concentrated into the water content of the carbon and no other water is used except as condenser coolant. This produces very high grade gold silver solutions which give high current efficiencies in the electrowinning step. These high gold concentrations allow almost complete separation of gold and silver from copper in the electrolytic cell. (c) The process is completed to a tailing assay of less than 200g Au/tonne carbon in 15 - 20 hours allowing turn around of carbon batches on a daily Basis.

Jan 1, 1982

By Kepplinger W

The KR Process is a joint development by VOEST-ALPINE, Austria and its subsidiary company KORF ENGINEERING, Germany. This new technology allows production of hot metal on the basis of non-coking coal. The KR Process is based on the idea of separating the process steps realized in the blast furnace (generation of reduction gas, reduction of iron oxide and melting of the reduced iron) and including coking of coal. These reactions are carried out in two reactors: - the melter gasifier, where non- coking coal is coked and gasified into a high quality reduction gas and hot prereduced iron is melted. - the reduction furnace, where iron oxide is reduced by the reduction gas generated in the melter gasifier and discharged in a hot state. In order to prove the process a pilot plant has been set up in Kehl/ Rhine in 1981 with a nominal capacity of 60.000 tpy.

Jan 1, 1986

By Smith Z, Huppert P, Charbucinski J

The paper describes a spectrometric method and apparatus developed for lithology logging in brown coal formations. The nuclear spectromet- ric technique developed is able to delineate coal/sand/clay seams. One requirement was to log inside drilling rods, as well as cased or open holes. The method described is based on combined natural gamma and gamma- gamma techniques using a spectrometric system for signal acquisition and subsequent computer based on-line data analysis and interpretation.

Jan 1, 1989

By Schonert K

The throughput of a HP-roller mill is determined by the acceleration of the feed material within acceleration zone and introduction into the compression zone. Both processes depend on the internal friction and the friction of the material on the roller surface which is influenced by the surface structure and adhering of material. The particle motion in the acceleration zone has been investigated with high speed videos showing the effect of the centrifugal force and the slip on the roller surface. The throughput is discussed in the term of the specific throughput which can be approximated by a linear function characterised by the throughput number and the throughput elasticity. The throughput number is a helpful measure for investigating the influence of the feed material and the surface structure. The experimental results give some guidance for chosing an optimum corrugation profile.

Jan 1, 1993