Search Documents

Previous methods for the assessment of the explosive potential of gas mixtures have required the plotting of apeexplosibility diagram. These became cumbersome if a large -number of assessments of various sampling locations over a period of time wererequired. This may make the approach of a dangerous situation more difficult to predict. With the aid of a programmable calculator, a new method for the rapid assessment of the explosibility of coal mine sample gases has been developed. This method does not require that an explosibility diagram be drawn to indicate the explosive status of a gas mixture. Simple Cartesian co-ordinates representing the explosive potential of,mixtures are obtained, which may readily be plotted to show changes with time.

Jan 1, 1981

By Beattie MJV

Widely diverse mechanisms exist for the action of a range of selective sulphide flotation depressants. Collector desorp- tion, leaching, competitive adsorption, formation of hydrophilic reaction-product coatings, action as reducing agents, and action as lattice-oxidizing agents are discussed. Detailed attention is focused on the latter two mechanisms. Recent works on copper depressants particularly for copper-molybdenum separations, and oxidizing agents enabling arsenopyrite- pyrite separations, are presented and discussed.

Jan 1, 1984

By Rozman L. I

This paper describes the latest open pit optimisation techniques,which now go beyond merely finding an optimal outline. The paper starts by briefly reviewing pit design techniques before optimsation. It then goes on to describe the pit optimisation procedure and the extensions to it which allow the automatic generation of nested families of pits. Next, the properties of families of nested pits are examined and the paper explains how they can be used to simulate certain mining sequences and schedules. Finally, we describe an actual study which was done using this kind of Software.

Jan 1, 1991

By Pathan AG

This research work is concerned with an investigation of the fracture toughness of sandstone, siltstone, and coal. Tensile failure trades have been examined with three different specimen geonetries, i.e; rectangular bar, round bar (in three point bending), and diametral compression discs. The Stress intensity approach, and J-integral methods were used to evaluate fracture toughness. Results from both approaches are discussed. True crack length was determined after pre-cracking, using the compliance calibration technique. Fracture toughness results of sandstone are independent of crack length and the size of the specimen. Fracture toughness may hence be regarded as a material property for sandstone. In cxnntrast fracture toughness values for !siltstone and coal are dependent on crack Length.

Jan 1, 1986

Cominco Ltd's Polaris Mine in Canada's High Arctic has been successfully mining zinc ore in permafrost since 1981. Mining methods using frozen backfill have been the key to success. The mine is now producing about 60 per cent of the ore from pillars while maintaining high productivities. Annual ore production is just over one million tonnes providing more than 200 000 tonnes of zinc concentrate each year. Cominco Ltd has adapted management and operating practices to suit the harsh environment and the isolated site, and has shown that a profitable development can be carried out in the tough Arctic conditions, with minimum impact on the environment.

Jan 1, 1993

By Wilson J. R

The main mining method employed at Mt Lyell is sub-level open stoping with a typical extraction level interval of 100 m and sub-level intervals of 30 m. Currently, pillar blasts provide the major portion of broken ore and firings are in the order of 200 000 to 300 000 tonnes while future firings of 500 000 to 300 000 tonnes are planned. Improvement of blasting techniques in these mass firings has been necessary for the following reasons. 1. Extremely wet ground conditions have adversely affected ANFO performance and placed extreme pressure on the charging and priming phases. 2. As pillar blasts increase in size the problems of wet ground conditions are accentuated resulting in very slow loading of wet upholes with cartridged gelignite and unreliable charging of the remainder with ANFO. 3 Fragmentation in pillar blasts has suffered because of the above, result- ing in increased secondary breaking costs and difficulty of extraction.

Jan 1, 1977

Intensive exploration for iron ore in the banded iron-formations (BIF) of the Pilbara region of Western Australia began in the early sixties and almost immediately established the Hamersley area as a major iron province. The early genetic models for the BIF-hosted ores were based mainly on macroscopic examinations of ores from the "hardcap" zone, and generally accepted a direct relationship with weathering effects on a Mesozoic to Tertiary land surface. Brandt (1964) was the first to suggest a difference in age between the high-grade hematite ores and the more common hematite-goethite types. He initially accepted a supergene origin for both, but later opted for a hydrothermal origin for the hematite ores. Apart from MacLeod (1966), the published views of the next decade reflect a largely parochial interpretation of individual ore bodies, centred mainly on supergene models but with some support for hydrothermal concepts. Except for Ayres (1971), none of the models were backed by detailed mineragraphic data. In 1976, an AMIRA-sponsored CSIRO group began a Province-wide investigation of the wide variety of ore types and BIF, with emphasis on geochemical and textural studies. The resulting conceptual model for a world-wide unified supergene and supergene-metamorphic hypothesis is generally accepted in the Hamersleys.

Jan 1, 1986

By Lang SC

The Broken River Province, in the northern part of the Tasman Orogen, is divided into the Camel Creek and Graveyard Creek Subprovinces. In the Late Cambrian to Early Ordovician, and again in the Late Ordovician, the northern part of the Tasman Orogen was probably a convergent margin with calc-alkaline volcanism. These episodes may have been separated by a passive phase in which quartz-rich flysch and tholeiitic volcanic rocks were deposited. Subsequently, in the Silurian, the region underwent extension forming a large turbidite basin which included the Camel Creek Subprovince and the Hodgkinson Province to the north. Melange is pervasive in the Camel Creek Subprovince which was folded twice in the Devonian. The melange may be related to thrusting accompanying D1. No rocks younger than Early Devonian have been recognised whereas, in the Hodgkinson Province, deposition continued until the latest Devonian. The Graveyard Creek Subprovince formed adjacent to the Camel Creek Subprovince, probably as a pull-apart basin on stable crust. The deformation history of the Graveyard Creek Subprovince contrasts markedly with that of both the Hodgkinson Province and Camel Creek Subprovince. In the Graveyard Creek Subprovince, melange is only present in Early Ordovician rocks. No major angular unconformities have been recognised in the overlying marine to non-marine sequence, which ranges from Early Silurian to Early Carboniferous. Several hiatuses and a slight angular unconformity, all within the Devonian, may be related to the major events in the Camel Creek Subprovince. A major deformation in the Graveyard Creek Subprovince in the Early Carboniferous had only slight effects in the Camel Creek Subprovince. Movement on the Clarke River Fault was probably an important influence on sedimentation and deformation in the Broken River Province.

Jan 1, 1990

By Savidis G

The characteristics of 'Z' (Back-over run) and 'R' (Reverse) ventilation systems are dis- cussed in relation to their suitability for longwall mining. Experience in European mines has been described as a basis for comparison with Australian conditions. In assessing the merits of each ventilat- ion system, such factors as longwall layout (pillar design, number of headings and gateroad stability), the need for gas drainage and bleed- er systems, as well as the influence of seam dip have been considered relevant. The R system is generally applicable for single and two heading development in seams where gas emission is a less serious problem. In contrast, the lower extraction to development ratio of the Z system (which arises from using three or more heading layouts) is considered more favourable where high gas emission occurs. The Z system provides greater flexibility with respect to the provision of refreshing air at the tailgate end, access of men and materials, installation and retrieval of gas drainage systems and the ability to interchange main- gate and tailgate roadways in cases where roof strata loads are difficult to control, or where cpam in hac an influrnra

Jan 1, 1983

By West-Sells P, King J. A, Patel C

The Eskay Creek orebody is located in north-central British Columbia (Canada). The ore contains major gold and silver values and minor but economically significant quantities of zinc. The refractory nature of the gold necessitates a pressure oxidation pretreatment prior to cyanidation. After solid-liquid separation the oxidation solution can be treated by oxyhydrolysis for iron removal and cementation with zinc dust for noble element removal. The resulting solution, as obtained in pilot studies, contains 7 - 10 g/L Zn, 0.5 g/L Ca and 2 - 4 g/L Mg. Minor amounts of cadmium, copper and iron may also be present in the solution. Over 90 per cent recovery of zinc from Eskay Creek oxidation solutions could be obtained by four stages of zinc extraction with Cyanex 302 extractant (Cyanamid Canada Inc, Niagara Falls, Canada). Zinc was stripped from the organic with spent zinc electrolyte in two stages. A complete description of the bench scale and miniplant studies of the solvent-extraction electrowinning circuit follows. The behaviour of minor amounts of copper, cadmium and iron in the circuit is also Discussed.

Jan 1, 1993

By Clarici E, Marsden J. R, Calderbank P. A

Evaluation of previous studies of multi-layer perceptron type artificial neural networks in the modelling of the deformability behaviour of rock have suggested that a deviation from the standard method of laboratory testing of rock under triaxial loading at constant confining stresses and constant axial strain rates may be inappropriate when the data produced are used to train an artificial neural network. In this paper, preliminary results of adopting such a strategy are reported. Of specific concern is the establishment of a suitable schedule for the stress path during testing. Furthermore, the training element of back propagation optimisation was directed towards prediction of new stresses given old stresses and old strain increments. Adoption of this method of supervisation in artificial neural network training facilitates the integration of the trained neural network within existing numerical methods used in rock mechanics. The target code was a finite difference Lagrangian formulation for the analysis of continua. Sandstone rock taken from a quarry in the UK was used in the study which showed that the method has great potential.

Jan 1, 1995

By Baafi EY

Open cut mining in Australia is facing the greatest challenge in its history in attempting to compete not only with other operations internationally, but also with underground operations domestically. Most flat dip and shallow depth surface-mineable coal reserves have been depleted during the last two decades and new open cut operations must extract deeper coal deposits. As open cut coal mines move into deeper areas and the stripping ratios increase, the relative cost of overburden removal also increases. It therefore becomes even more important to design the mine around the optimum overburden removal scheme. The deeper mines are usually multi-seam operations with a more complex geology and with more geotechnical and hydrological problems. Deeper mines are subjected to greater problems requiring more detailed mine planning and design, such as selection of the optimum mining method and pit layout. In planning and design of such operations, the number of alternative methods which need to be considered is consequently greater.Dragline productivity and its stripping capabilities are directly affected by the selection of digging method, strip layout and pit geometry. Every mine has a unique combination of geological conditions. The operating methods that work well at one mine may not necessarily work at another site. Selection of an optimal stripping method, strip layout and pit geometry for a given dragline must be considered with respect to the geological conditions of the mine. With increasing geological complexity of Australian strip mines, it is becoming more important to use sophisticated techniques such as computerised mine planning methods to assist in optimising dragline operations.

Jan 1, 1998

The nickel ores mined in New Caledonia for one century are mainly silicate ores. These ores are nickel enriched saprolites, formed by partial weathering of peridotites (predominantly harzburgites and some dunites), serpentinised to varying degrees. Saprolites constitute the lower horizon of lateritic soils, sometimes up to 100 metres thick, developed on peneplains now greatly modified by erosion. Saprolites are generally overlain by laterites, a more weathered horizon, where the main components are iron oxy-hydroxides with a low nickel grade. The structure of saprolites depends essentially on the serpentine content of peridotites and, on the other hand, serpentine minerals may have a high nickel content and, so, represent important nickel bearing minerals in silicate ores. Two types of serpentines can be found in nickel ores from New Caledonia: ò primary serpentines, formed by hydration of olivine at temperatures below 400¦C, during overthrusting of peridotites in late-Eocene (Paris, Andreieff and Coudray, 1979), are generally very abundant; ò secondary nickeliferous serpentines, associated with other sheet silicates in garnierites, are now relatively scarce but garnierites were selectively mined one century ago, because of their high nickel grade.

Jan 1, 1996

By R C. Morris

The channel iron deposits (CID) (Ramanaidou, Horwitz and Morris, 1991; Morris, Ramanaidou and Horwitz, 1993; Ramanaidou, Morris and Horwitz, 2003; Morris and Ramanaidou, 2007) are one of the two major iron ore types mined in the Hamersley Province. The CID provided around 41 per cent of the total of 268 Mt of iron ore mined from the Hamersley Province in 2006. The current CID resource is around seven billion tonnes. The CID deposits occupy numerous meandering palaeochannels in a mature surface that includes Precambrian rocks and ferruginous palaeogene valley fill. These palaeochannels are generally less than a kilometre but can range to several kilometres in width and from one metre to more than 100 m thick. The two currently mined CID areas are located:in the western Hamersley Province in the Robe palaeochannel, and in the east in the Yandi palaeochannel. These two major CID channels extend over 100 km to 150 km, with the Robe system up to 5 km wide. The granular ore facies typically contains ooids and lesser pisoids with haematite nuclei and goethite cortices, with abundant goethitised wood/charcoal fragments and goethitic peloids, minor clay and generally minimal porous goethitic matrix. Post deposition weathering is common and produced secondary facies.Ooids and pisoids were mostly derived from the stripping of a well- vegetated deep ferruginous surface. The peloids were derived both intraformationally from fragmentation and reworking of desiccated goethite-rich mud. Minute wood/charcoal fragments in the soil that were initially replaced by goethite and then dehydrated to haematite, formed nuclei for many ooids and pisoids. In addition, abundant, generally small (in situ by goethite within the consolidating CID. This profusion of fossil wood, both as ooids and pisoids nuclei and as discrete fragments as well as the local presence of kenomagnetite suggests major episodic wild fires in heavily vegetated catchments. The goethitic matrix was the result of chemically precipitated iron hydroxyoxides, resulting from leaching of iron-rich soils in an organic environment.

Jan 1, 2007

By White PJ, Worrad C

The Hunter Valley Coal Preparation Plant and associated materials handling facilities commenced operation in mid 1982. The new plant and coal handling system were designed to integrate with existing mining and preparation plant operations, but also to be flexible to future mining and marketing developments. The system includes: raw coal stockpiles, a 900 tph dense medium/water washing cyclone preparation plant, clean coal stockpiles, a 7.8 km overland conveyor, large finished product stockpiles and a high capacity train loading plant.The plant's development is described with reference to the original planning objectives. Features aimed at providing operational flexibility and performance are emphasised, including the use of; automated stackers and reclaimers, modular plant, distributed PLC control, a single flight overland conveyor, a network of automatic samplers and blending options to assist quality control.Details are also provided of an innovative technique for control of reclaimer rail track forces, stacker and reclaimer anti-collision systems and the use of DC injection braking.

Jan 1, 1985

By T QUINLAN

A resource estimate uses data obtained by sampling an orebody. An example is described in which a random drilling pattern did not provide a representative set of assays, and the estimated resource was significantly less than the mine production. It is believed that a better estimate would have been made if the exploration holes had been drilled on a regular grid.

Jan 1, 1992

The Hunter Fracture Zone can be traced into the Fiji group, and onshore SE Viti Levu in the form of NE-trending morphostructures. NW- trending morphostructures offset the NE elements. Structural mapping of Suva Harbour indicates that the NE elements are grabens bordered by faulted monoclines. Faulting is characterised by block-rotations and dip-slip displacements. The NW morphostructures are faults displaying elements of both dip-slip and strike-slip movement. Structural overprinting suggests that the NW faults represent the youngest phase of deformation, and current seismic activity occurs on this trend. A conceptual, geomechanical model of the deformation invokes toppling and wedge failure at the edge of the Fiji platform, translating material downslope into the Hunter Fracture Zone. The interference pattern produced by the superposition of the NW on the NE structures consists of a series of circular features bearing superficial resemblance to volcanic centres. Known mineral deposits in SE Viti Levu correspond closely to these features. The formation of the circular features postdates mineral genesis, suggesting that the features provide a focus for the enhanced exposure of mineral deposits rather than a source of mineralisation. There is a close association between mineralised exposures and interference patterns in extensional structures in SE Viti Levu, and a correlation between these structures onshore, and the Hunter Fracture Zone cum South New Hebrides Trench offshore. Future mineral exploration in the SW Pacific will benefit by closer consideration of the geologic structure of Pacific islands bordering the extensional regimes of deep oceanic trenches.

Jan 1, 1987

By Shklyar FR, Bokovikov BA, Gordon YM, Scherbatskii VB, Yaroshenko YG, Shvydkii VS

The paper presents, for the first time, a complete mathematical model of the flow of gases in packed beds which describes the processes of gas-mechanics in iron blast furnaces and other shaft type smelting units. Good correlation between calculated and experimental results was obtained confirming the adequacy of the model. It is shown that the uniformity of gas distribution is related to the tuyere size and the extent of its protrusion into the furnace and that these variables may be used to regulate gas distribution across the furnace diameter. It is also concluded that furnace height has no significant influence on gas distribution. The necessity for a mathematical description of raceway phenomena has been experimentally proved. Conclusions from theory are shown to have profound implication to furnace design and operation.

Jan 1, 1975

By B Andrew, L Krois

Ground control systems, including ground control management, play an integral role in the effective and efficient extraction of copper ore at the Xstrata Copper û Mount Isa Copper Operations (MICO). Rock mechanics engineers and support technicians at Xstrata Copper have undertaken a wide range of investigations and actions over the past few years. Outcomes from this work have resulted in the evolution of ground control management practices on the site. Specific areas of improvement include the installation of efficient one pass ground control systems, greater application of sprayed concrete for areas requiring rehabilitation and the addition of new improved products, the removal of obsolete and less efficient products used in standard ground control practice. In some areas underground, the most effective methods to manage ground control hazards continue to be a variation on proven methods that have been in use for many years in the MICO. Ground control systems for developing through the basement contact zone are very similar to that developed in the late 1980s. Similarly, ground control systems have gone through repetitive evolution, whereby some systems fall in and out of favour subject to perceived costs. For example the pouring of concrete shuttering around drawpoints in poor ground conditions has recently been re-accepted as an effective means to manage this poor environment û despite having been previously cast aside as too expensive. Ground control management systems continue to evolve towards the goal of creating a workplace that is free of rockfall-related injuries and provide for higher levels of efficient and effective techniques by which ore is extracted from the ground.

Jan 1, 2005

By I M. Platten, Y Xie

Narrow vein gold mineralisation generally contains both fine (<100 ¦m) and coarse (>100 ¦m) gold particles. The in situ size and shape, deportment, distribution and abundance of the particles controls deposit sampling characteristics, grade distribution and metallurgical properties. Particles can range from individual disseminated grains, clusters of particles and masses above 1 cm in size. At each end of the coarse-gold to fine-gold spectrum, the samplability of a deposit ranges from relatively simple for fine-grained disseminated gold particles, through to extremely difficult for very coarse particles. Deposits generally show a background grade of mineralisation dominated by disseminated fine gold particles. Drilling will resolve the background grade well, though is likely to considerably understate the grade related to the coarser gold particles. Gold mineralogy has a significant impact on metallurgy, with key factors affecting recovery being particle size, deportment, liberation parameters and silver content of gold minerals. For coarse gold particles the focus should be on liberation and the early removal of the particles from the mill circuit by gravity concentrators and gold traps. Finer particles will require more grinding to liberate prior to flotation or cyanide extraction. The determination of gold particle sizing is thus required to minimise evaluation and geometallurgical uncertainty and lower project risk.

Jan 1, 2008