Search Documents

By R. A. Sullivan

I T IS one of the unwritten policies at Preston Mines that we examine closely any method or tool that will help us in our constant battle against rising costs. It is our personal conviction that most work methods can be improved. Therefore even though the job went well yesterday, it does not necessarily follow that it should be done by the same method today. With the arrival of the natural gas pipe line in the Porcupine area it was obvious that we would have to take a good look at the possibilities of using this source of fuel for plant heating. • Steam presently generated at Preston is for heating purposes only, no process steam being required. Prior to the fall of 1960, the heating plant consisted of two low pressure, coal-fired, fire-tube boilers, operating at an approximate pressure of 14 pounds per square inch. These boilers were underfed by stokers and could be operated either singly or together. ~o. 1 unit was a horizontal return tubular boiler, registered at 100 h.p. No. 2 unit was a fire-box boiler, registered at 75 h.p.

Jan 1, 1962

By Y. Shu, A. R. Laplante

"A laboratory Knelson Concentrator (LKC), 7.5 cm in diameter, was used to study the performance of a similar unit at plant scale, 76 cm in diameter, This paper reports on sampling and assaying procedures and problems, and discusses the performance of the plant unit.The sampling procedure was based on the extraction of large samples, 5-15 kg, and their complete processing with a LKC, to characterize size-by-size performance. The procedure yielded reliable estimates of overall gold assays, after blatant assaying errors were corrected. The plant centrifugal unit concentrate was sampled in situ, which yielded very erratic grades, with a large overall negative bias. Due to the very heterogeneous nature of the concentrate, which can be linked to flow patterns in the riffles of the unit, it is recommended that for future testwork, the concentrate be recovered separately, blended and then sampled.The plant centrifugal separator, when operated at a feed rate of 25 t/h, yielded total and free gold recoveries of 41 % and 62%, respectively. This is much lower than previously reported data, and suggest that at 25 t/h, the unit is overloaded. However, recovery did not decrease with time over a loading cycle of 2 hours, which suggests that present loading cycles, generally 1 hour, can be significantly increased. INTRODUCTIONThe study of gold gravity circuits is plagued with the statistical problem of determining the behaviour of particles occurring with a very low frequency. This problem becomes particularly acute with increasing particle size. For example, considering the average weight of a gold flake in the 840-1200 µm (20/28 mesh) to be about 5 mg (Banisi et al, 1991), a reasonably high grade feed of 10 git would require, for a relative error (standard deviation) of 10% on grade, 100 particles, that is 0.5 g of gold, or 50 kg of 840-1200 µm material (a Poisson distribution is assumed). Gy's formula, for the same data, yields a weight of 33 kg, with a shape factor of 0.1 and a size distribution factor of 0.5. Both results are comparable; to obtain the suggested weight of material, a stream containing 5% weight in the 840-1200 µm would require 1 tonne samples (of unsized material). The problem rapidly disappears with decreasing particle size. Still with Banisi et al's data, a gold flake in the 300-420 µm range averages 0.5 mg in weight; the same 10% error on grade corresponds to a weight of 5 kg. Gy's formula for the same size distribution and particle shape factors as above predicts a required mass of 1.4 kg. This would correspond to an unsized sample weight of 10 kg with 14% weight in the 300-420 µm, for example."

Jan 1, 1992

By Wayne D. Goodfellow, William M. Luff, Steven J. Juras

Abstract-Brunswick No. 12 is a vent-proximal massive sulfide deposit that formed above a feeder pipe with associated hydrothermal alteration. Because of the replacement of bedded sulfides deposited above the hydrothermal vent, individual sulfide lenses show the following vertical and lateral zoning outward from the vent complex: massive pyrite-pyrrhotite-chalcopyrite core - interlayered pyrite-sphalerite-galena (Pb-Zn ore zone) - bedded pyrite. The feeder zone which underlies the Cu-rich core consists of an anastomosing network of pyrite-pyrrhotite-chalcopyrite­ quartz veins with variable and generally minor contents of ferroan carbonate, Fe-rich chlorite, sphalerite, galena and arsenopyrite. Hydrothermal alteration of felsic igneous rocks hosting and adjacent to the feeder pipe is represented by an inner zone (zone 1) characterized by sulfide stringers, Fe-rich chlorite, muscovite, quartz, and ferroan carbonate that formed at the expense of feldspars and what was probably glass; outer zones (Il and III) are represented by Mg-rich chlorite and muscovite formation, and the albitization and silicification of K-feldspar. Accompanying these alteration trends is a marked decrease of Na + Ca, and an increase in Fe + Mg + C03 in zone 1, and increases in Mg + Na in the outer zones. The classic zoning of metals within the sulfide lenses, the formation of a feeder pipe below the vent-proximal sulfide core, and the hydrothermal alteration of felsic volcanic rocks cut by the feeder pipe all support a vent-proximal origin for the Brunswick No. 12 deposit. Furthermore, restriction of sulfide stringer mineralization to the footwall sequence, the folding of the stringer zone by an F1 fold, and the difficulty of long distance mass transfer of metals from the sulfides into the host rocks all argue against a tectonic origin for the stringer zone. All of the evidence indicates that the feeder pipe formed during the ore forming hydrothermal event, but has been distorted and in some areas detached from the overlying massive sulfides during subsequent deformation.

Jan 1, 1992

By B. C. Jago, H. Derbuch

"The Freightrain kimberlite is located on the Brodeur Peninsula, Baffin Island, Nunavut. Twin Mining is exploring the pipe and adjacent land (79 claims/655 km2) using a combination of airborne geophysics, soil sampling, diamond drilling, trenching and bulk sample processing. The pipe originally was discovered by Cominco Limited in 1975, re-evaluated in 1993 by Lumina Investment Corporation, when it was staked as the Zulu pipe, and subsequently covered by three claims in 1998 by Helix Resources who called it Freightrain.The Freightrain pipe coincides with a strong, ovoid-shaped aeromagnetic anomaly. It is the only surface exposure of kimberlite within a 30 km long linear trend of fourteen aeromagnetic anomalies that are up to 600 m in diameter.The pipe is exposed in the crater facies, near the transition into diatreme facies as indicated by the occurrence of pyroclastic kimberlite characterized by abundant olivine macrocrysts, juvenile lapilli and kimberlite autoliths set in a serpentine-calcite matrix. Olivine, Cr-pyrope garnet and chromite are the most abundant macrocrysts; clinopyroxene, ilmenite and phlogopite mica occur in minor to trace amounts. Garnet and chromite harzburgite, garnet lherzolite, garnet-spinel lherzolite and rare eclogite dominate the xenolith population.Garnet and chromite mineral chemistry indicate encouraging diamond prospectivity and that potentially diamondiferous garnet and chromite harzburgite were the principal sources of diamond in the mantle at the time of kimberlite eruption.Single clinopyroxene grains define an ~42 mW/m2 sub-continental geotherm that is rooted in the diamond stability field. This compares to a slightly hotter geotherm (~48 mW/m2) for adjacent Somerset Island kimberlites with an origin in the graphite stability field. This data accords with the general lack of sub-calcic Cr-pyrope garnet, diamond inclusion chromite and diamond in Somerset Island kimberlites."

Jan 1, 2002

By V. K. Gupta

"Effect of mill speed on grinding kinetics has been investigated with a view to using mill speed as a manipulated variable for control and optimization of the grinding circuit performance under variable ore hardness conditions. Dry and wet batch grinding tests were carried out for quartz, limestone and cement clinker in a 29 cm x 18 cm laboratory ball mill. Mill speed values selected were 55 and 70% critical. In the case of dry grinding operation, with an exception of quartz, for all materials studied the effect of mill speed on grinding rate was found to be insignificant for sizes finer than about 35 mesh. In the case of wet operation, grinding rates were found to be approximately proportional to the mill speed. The implications of these results are discussed.INTRODUCTIONIt is well known that mill speed has a considerable effect on the grinding rate of the ore particles l-3 For particles of a given size there is an optimum speed at which mill grinding efficiency is maximum (i.e. specific energy consumption is minimum) 3•4. Mill speed can, therefore, be effectively used as a manipulated variable to deal with the disturbances arising from changes in the size and hardness (grinding rate) of the ore being fed to the grinding circuit. Though, it has not been the case so far, with recent developments of ring motors2 and frequency inverters5 a continuous variation of mill speed has now become feasible, and it is expected that mill speed control will soon be a regular feature of plant operation2,6."

Jan 1, 1985

By N. Hmidi, T. Yalcin, M. Papadakis, B. Hilscher

Mill tailings, containing iron sulphides in particular, pose an environmental concern since they constitute a potential source of acid mine drainage which can damage vegetation, harm soil and living organisms, and contaminate groundwaters. Proper disposal of acid generating tailings is therefore an important issue that must be addressed and resolved in a satisfactory manner. Placer Dome Canada operates a 4000 t/d gold cyanidation facility at Musselwhite mine, in northwestern Ontario, where the mill tailings have been classified as acid generating. This study was conducted to explore the effectiveness of froth flotation in removing the sulphide minerals from these tailings and producing a low-sulphur, non-acid generating material that could serve as a capping material for previously deposited tailings. Laboratory semi-batch flotation tests were carried out in accordance with an experimental design procedure, and a computer simulation program was developed to facilitate the evaluation of flotation performance. In this investigation, pH, collector concentration, and airflow rate were considered as the relevant flotation variables, and their effects were examined both experimentally and by simulation. Results have demonstrated that flotation can successfully desulphurize the Musselwhite mine tailings and render them non-acid generating.

Jan 1, 2004

By Jing Li, Weiqiang Lai, Joe Zhou, Jiezhen Ma, Shuibo Chen, Ashele Copper Company, Feng Gao, Guofu Feng

"Copper-zinc ores often contain gold and silver, which can be recovered into copper concentrate by flotation as by-product. The challenges for operations that produce copper, zinc, gold and silver are the separation of copper and zinc and the low grade of precious metals. Ashele copper-zinc ore in north China contains 2.38% Cu, 0.69% Zn, 0.21 g/t Au and 18.10 g/t Ag and the plant produces copper and zinc concentrates, with gold and silver being recovered into copper concentrate. Copper occurs mainly as chalcopyrite and Zn occurs as sphalerite. Copper is well recovered with a recovery of over 94%. However, the recovery of Zn is substantially low (around 50%) due to fine grain size of sphalerite. In addition, gold recovery is much lower than expected and only 33% of gold in the flotation feed was recovered. The grade of gold in copper concentrate is also lower than the required payable grade (1.0 g/t). To determine the cause for lower Zn and Au recoveries, a plant survey program was conducted on the operation. The information acquired shows that the loss of Zn was mainly in the copper concentrates (accounting for approximately 38% of the head assay); of which, 24% was liberated, 8.5% was associated with chalcopyrite and 4.6% was associated with pyrite, indicating that the separation of copper and zinc was the main cause for the Zn loss, with liberation being the second cause for Zn loss. Future effort in improving Zn recovery should be focused on the separation of zinc from copper. Gold in the ore occurs as both microscopic gold and submicroscopic gold, accounting for 36% and 64% of the head assay, respectively. Microscopic gold occurs mainly as native gold and electrum; it is relatively coarse with a grain size of 10 to 240 µm and a large portion can be recovered by gravity. Submicroscopic gold was mainly carried by pyrite (accounting for 38%), and to a less extent, by tennantite (15%) and chalcopyrite (10%). Gold in sphalerite is nominal (1%). It is suggested that more coarse gold and tennantite be recovered and a gold recovery increase can then be achieved to obtain a copper concentrate with over 1.0 g/t Au through flowsheet optimization. Gravity concentration should be investigated and may be worth added into the existing flowsheet to maximum the gold recovery and grade.INTRODUCTIONCopper-zinc ores containing gold and silver is a subtype of polymetallic sulphide ores. Unlike porphyry copper sulphide ores and iron-oxide copper-gold ores, this type of ores often contains substantial amounts of zinc and lead. Polymetallic sulphide ores are mainly distributed in Canada, such as at the LaRonde and Horne deposits. Other examples include Mt. Morgan in Australia and Boliden in Sweden. Globally, production and reserves from gold-rich VMS deposits account for 1370 t gold. This is equivalent to 1% of the world production and reserves, whereas the Canadian total for gold-rich VMS deposits is 870 t, representing close to 10 % of Canadian production and reserves (Gosselin & Dube, 2005a, 2005b). Flotation is the principal process for processing the copper-zinc sulphides ores, for subsequent smelting, roasting, or hydrometallurgical treatment. Oxidized copper-zinc ores can also be processed using leaching technology. For example, at LaRonde operation (a Cu-Zn-Pb ore containing 3-4 g/t Au and 60-100 g/t Ag) the flowsheet consists mainly of a copper flotation circuit and a zinc flotation circuit followed by a cyanidation process of flotation tails. The precious metals are recovered with copper concentrate, zinc concentrate and cyanidation of zinc tails via Merrill Crowe precipitation (Zhou et al., 2005)."

Jan 1, 2016

By J. Girard, V. Aubé, M. Barakate, S. Bellec, M. R. Eddahabi, Y. Chaik, M. Deshaies

"The activated carbon used in the carbon-in-leach (CIL) process to absorb gold is subject to breakage. This carbon breakage can be minimized, but it will always be necessary to deal with fine carbon particles, known as carbon fines. These fines contain a significant amount of gold and mining operations generally struggle with the treatment of this product. Since IAMGOLD’s Essakane mine is located in Burkina Faso, shipping carbon fines out of the country was not considered a viable solution due to the logistical burden and legal procedures in place. A benchmarking study demonstrated the complexity of treating carbon fines on site. IAMGOLD partnered with the host government to find an innovative approach to economically recover the gold locked in these fines. This paper describes the new circuits commissioned in July 2016 built to improve carbon fines collection, incinerate the carbon fines and leach the gold in the ashes produced by incineration. These new circuits successfully demonstrate that it is possible to extract more than 94% of the gold content in the carbon fines. This is profitable for the company as it improves the overall mill recovery rate by 1.0% to 1.5% and significantly decreases gold inventory build-up on site.INTRODUCTION The activated carbon used in the carbon-in-leach (CIL) to absorb gold is subject to breakage. This breakage can occur in the CIL tanks, the stripping circuit, the regeneration process or anywhere throughout the pumping and handling processes of carbon through the circuit. Fine carbon particles are invariably created and, because of their small size, present a large specific surface which favors gold absorption (Hilsher et al., 2014). At the very beginning of operations at Essakane, the carbon fines were recovered by means of a thickener and a filter press, but the circuit was undersized and inefficient. Subsequently, a decantation basin was used to settle the fines before the thickener. The settled fines were shovelled from the basin into bags. All these bags were stored in the backyard of the plant. The average tonnage of carbon fines recovered monthly was 23.5 tons with a gold grade at 1938 g/t."

Jan 1, 2017

By R. E. MacAfee

THERE have been great changes in the design, capacity, and pressure of steam generating units over the past fifty years. If we go back as far as 1890, the plants then existing were largely horizontal return tubular boilers, hand-fired, with the boilers supported on the brick sitting which was com-posed of red brick with, probably, a refractory lining one brick thick in the combustion chamber. About this time, the water tube boiler began to supplant the H.R.T. boiler and, where new plants were being constructed of any size, water tube boilers were largely installed. In those days, say from 1890 to 1905, a 250 h. p. water tube boiler was considered a large unit. These boilers were largely the straight tube type and were set with the first row of boiler tubes three to six feet above the grates. The brick setting was a combination of red brick and fire-brick. The fire-brick lining in the furnace proper was usually 9 in. thick and in the first pass 4 1/2 in., while the rest of the setting was entirely red brick. These units were largely hand-fired and were expected to produce about 100 per cent rating as a maximum. It may be well at this point to define rating, which is the evaporation of one boiler horse power per hour by each ten square feet of heating surface in the boiler. A boiler horse power is the evaporation of 34.5 pounds of steam from and at 212°F. Consequently, a boiler containing 2,000 square feet of heating surface is rated at 200 h. p. and the evaporation at 100 per cent rating is 200 X 34.5, which equals 6,900 pounds of steam per hour from and at 212°F.

Jan 1, 1939

By Chris M. Healey

"Abstract- The Jasper Gold mine in northern Saskatchewan produced a total mill feed of 140 127 tonnes at an average grade of 19.0 g/t Au. Both diamond drilling and chip samples from under­ ground workings returned extremely high values, up to 12 851 g/t (375 oz/I) Au over 0.10 meter from a chip sample. In the presence of such extremely high grades, the accurate estimation of reserves is a major problem.ln the first part of this study, production data from the mine were used to evaluate the results of a variety of reserve estimation techniques in this environment. In two out of three cases studied, indicator kriging with assays cut to 342.9 g/t (10 oz/I) gave extremely good results. In the third case, however , indicator kriging gave unacceptable results. Instead, lognormal kriging of uncut data gave the best results.Secondly, from the same database, a number of drill-hole spacings were simulated, and reserves estimated from the simulations. As may be expected, the results of this analysis show increasingly better results with tighter drill-hole spacing. However, even with a 5 m by 5 m spacing the variation from actual grade was quite large. This is not a systematic under- or over-estimation of grade, rather a random scatter of results .The results of this study show very clearly the problems of deriving good estimates of reserves when extremely high-grade samples are encountered. There is a high degree of randomness to this database, so reserve estimation in this situation will remain a high-risk operation."

Jan 1, 1993

By Pedram Sahba

In today?s emerging economy, pooling resources is a growing trend to reduce overall system costs. Two important resources of every maintenance department are repair shops and spare parts. In this work, we consider a system consisting of mine drills at multiple areas in a mine. In each area, a number of identical drills are operational. When a failure occurs, the defective component should be repaired in a designated repair shop. The failed component can be replaced immediately if a spare part is available. Otherwise, the drill is down until a component is repaired and put back into service. In this paper, the effect of pooling resources is examined, and the conditions under which it is beneficial to pool the resources are investigated. In addition, determining the optimal number of stand-by units, equipment or spare parts, in each case is of interest.

May 1, 2013

By C. V. Deutsch, O. Babak, J. G. Manchuk

High levels of geological heterogeneity occurring over relatively short distances pose a challenge to the unconventional open-pit techniques used in oil sands mining. There is strong motivation to mine selectively and minimize dilution and loss; however, the large equipment and high mining rate used to meet production targets tend to reduce selectivity. A numerical model is developed to account for geological complexity, mining equipment, regulatory criteria, and other operational parameters. This framework is used for more accurate forecasts, optimization of equipment, and other operational decisions. An example demonstrates the approach in light of Alberta Energy Regulator criteria.

Jan 1, 2014

By E. Henderson, L. K. Daneshmend

Drawpoint control is critical in determining the cutoff point for load-haul-dump mucking operations to minimize dilution. It is also necessary to ensure even mucking distribution and to prevent possible hang-up of material within a stope. A prototype production monitoring and reporting system has been developed for load-haul-dump operations in under-ground mines. The system generates accurate and timely information regarding mucked tonnages and drawpoint and ore/waste pass utilization. The monitoring system integrates a PLC-based load weighing system with a radio frequency identification (RFID) system for locating the vehicle. The system records the identification and time of entry and exit of each draw-point and ore/waste pass visited during a shift, as well as the weight of each bucket load. A trial of the system was conducted at the CAN-MET Experimental Mine near Val d’Or, Quebec. The monitoring and reporting system functioned as designed, with the exception that the maximum read range of the RFID tags under dynamic conditions was found to be a limitation. RFID systems with greater range capabilities have been identified for a second generation system. The system is the first of its type in North America to demonstrate that RFID tagscan be successfully applied to locate trackless underground equipment. Because of their ability to locate equipment and personnel within underground mines, RFID systems should be considered a key technology for future mine information and process control systems.

Jan 1, 1996

By S. Bergquist

In this paper, it is investigated how different types of automation would affect the safety for workers in asphalt paving. The risk for the workers on road construction sites is consistently high in comparison to the average risk of the working population. Automation has been suggested as an alternative for improving the safety in roadside construction assuming that removing workers will inherently eliminate the risk of them being injured. In this paper, the potential for improving the safety using automation is analyzed in detail. By investigating accident statistics and understanding the type of accidents that appear, several different automated functions for increased safety are proposed and described. Based on available statistics, it is possible to estimate the safety benefit, as the reduction in fatalities, for several of the proposed functions. The highest safety benefit would be achieved by automating the road traffic driving through the work zones. This has the potential of reducing the total number of road worker fatalities with over 30 %. In addition, it would decrease the number of road traffic accidents in work zones. Automation of construction machinery and dump-trucks also has the potential to increase the safety.

Aug 1, 2013

By S. Banisi, H. R. Iran-Manesh, M. R. Shayestefar, H. Shekarchyan

"Flotation circuit of the Sarcheshmeh copper mine processes 41,000 t/d of ore at 0.9% Cu. Chalcopyrite and chalcocite are the main copper bearing minerals which are concentrated in three stages of roughing, cleaning and recleaning. Due to major changes in the reagent addition regime, make-up balls combination, and throughput to the primary mills an increase of 2.6% (from 87.2% to 89.8%) in the sulfide copper recovery was obtained during a period of six years. In order to investigate a rather large variation of monthly recovery (i.e., from 89.0 to 91.2%) of the plant after implementation of the changes, a study was undertaken to trace mineralogically possible causes of such a behavior. During a five-month period, monthly composite samples of feed and tailings of the flotation circuit were taken. At the first stage, the polished sample preparation method and the mineral counting procedure were optimized through a detailed study. Liberation degrees and types of locking of valuable minerals in both streams were determined in three size intervals of +75, +38 and –38 microns. It was found that for both recovery levels (i.e., 89% and 91.2%), there was no significant difference in the liberation degrees of valuable minerals in the flotation feed; the average liberation degree was 57.1% with a standard deviation of 3.1%. On the other hand, in the case of high recovery level (i.e., 91.2%) there was a reduction of 15% in the amount of free valuable minerals in the tailings stream. The highest reduction was found for the -38 micron size range in particular for chalcocite. It was concluded that compared to the grinding circuit the change in the flotation circuit had the significant effect on the plant recovery increase.INTRODUCTIONThe Sarcheshmeh copper ore body contains 1 billion tonnes averaging 0.90 % copper and 0.03 % molybdenum. It is located southeast of Iran and currently processes 41,000 t/d of ore. The concentrator has been in operation since 1982. Last year, the concentrator produced 130,000 tonnes of copper and 4,000 tonnes of molybednite concentrate. An expansion to the plant which will increase the throughput by 50% is under construction and will be effective in 2003.After three stages of crushing, the ore with a F80 of 12.7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of the first stage of flotation is reground and the tailings constitute the main component of the plant final tailings. A concentrate with an average grade of 30.5% Cu is obtained after cleaning and re-cleaning stages. At the present time, the average sulfide copper recovery of the plant is 89.8% which varies depending on the operating conditions and ore type."

Jan 1, 2003

By Patrick M. Y. Waye

As mines utilise more automation in mining operations to improve efficiency and safety, a corresponding increasing demand is placed on the transport of information. Some of the recent technological advances in underground telecommunications are described for various data, voice and video applications. In particular, two new innovative underground communication systems are described, one with high speed data at 30 Mbps and the other for mine wide evacuation and safety applications. The high speed data system incorporates stateof- the-art data networking technologies and the existing leaky cable narrow band radio channels. The new system provides over the same basic infrastructure the high speed data network at 30 Mbps TCP/IP Ethernet with 100 Base-T interconnection, plus 32 narrow band radio channels. The second system is a system for mine wide evacuation with "through the earth" communication infrastructure. Emergency situation can be communicated to and from all the miners within seconds through a central control location. The technology involved does not require leaky cable or any other similar transmission media installation. Many applications are possible, including warning miners of emergency situations, mine rescue operation to communicate with trapped miners, regular reporting from miners working alone.

May 1, 2001

By W. J. Bennett

WHEN Dr. Horace Fraser, your President, invited me to speak to you today I advised him in confidence that I was leaving my present positions on April 30th. In the circumstances it seemed to me that this audience might prefer to have as its speaker one who wo.uld J1ave a continuing association with the atomic energy programme. Dr. Fraser was kind enough to suggest that my re-marks might he of special interest to you, since I would be able to sum up my views on the atomic energy programme. I hope that I will not disappoint him or you on that score. I am particularly pleased that my last public appearance in my present positions should be at the Annual Convention of the C.I.M. since, as all of you know, a very important part of my work has been in the mining field. As it happens, my first public address on the subject of atomic energy and its raw material -uranium -was made at your Annual Convention in Montreal in April, 1949. It seems fitting that my final address should also be made at this convention -nine years later.

Jan 1, 1958

By R. F. Tylecote

"The closure of the iron and steel making plant at Consett in Durham in 1980 marked the end of an era-a long era in the world's iron and steel making history. Iron had been smelted in the Tyne-Wear area of the United Kingdom since before the Roman period, but apart from evidence of smithing in the Roman period, the historical evidence for iron production on a large scale dates from the 14th century.The paper describes sites in the area that first worked the bloomery process and then, in the 16th century, as did most of Europe, graduated to the blast furnace process. The main emphasis is on the early introduction of coal to iron making at the end of the 18th century and the use of the steam engine to render integrated sites possible.IntroductionIron has been smelted in the Tyne-Wear area of the United Kingdom since before the Roman period, but apart from clear evidence of smithing in the Roman period, the historical evidence for iron production on a large scale dates from the 14th century. Like many other countries, the United Kingdom benefitted from the visits of foreign observers, such as Jars, Svedenstierna, de la Houliere and Dufrenoy, who left detailed records. In modern times, information gained from excavations of iron and steel making sites has supplemented the historical record.Natural ResourcesUp to the end of the 19th century, the industry was wholly dependent on its own resources. Iron ore, limestone, wood, coal and water power were all found a short distance away from the main valleys of the Tyne and Wear. The main sources of iron ore were the coal measures, with rider ores from the lead vein s in Alston and Weardale, and carbonate ores from shale horizons in the Carboniferous limestone. Good coking coal was available from West Durham and reasonable coal from the Tyne valley and Northumberland limestone. Limestone was plentiful."

Jan 1, 1983

By J. C. Gathje

Newmont acquired the Phoenix Project through the acquisition of Battle Mountain Gold in 2000. Shortly after the acquisition, Newmont Metallurgical Services (NMS) and Nevada Operations began development work on a process to Pressure Oxidize (PDX) precious metal rich copper concentrates from Phoenix using the Lone Tree PDX facilities at Valmy, Nevada. The high precious metals content of the Phoenix concentrate - Au up to -300 g/t and especially Ag, up to -1700 g/t - led Newmont to the development of a High Temperature PDX process that achieves high cyanide leach recovery of Au and Ag, from the PDX solids, without the requirement for a messy and expensive "lime boil" or sulphate destruction process. Base metals content in Phoenix concentrates range from: 15-25 % for Cu, 1-10 % for Zn and 0-2 % for Pb. Excellent solution extraction of Cu and Zn is achieved while Pb is precipitated in the PDX residue. In addition to achieving high Au and Ag recovery this process produces very clean PDX discharge liquors that require minimum effort to remove contaminant metals and PDX solids that have superior settling and filtration characteristics. All of these factors contribute to lower capital and operating costs for the overall process. This paper describes the laboratory and PDX pilot plant developments for this process.

Jan 1, 2004

By T. Loos

The Norddeutsche Affinerie operates an Outokumpu-Flash-Furnace as a smelting unit. The pyrometallurgical slag cleaning process is based on the slag reduction and settling in the electric furnace. Since 1972 when the slag cleaning furnace was built the throughput could be increased fourfold. However, an extensive optimisation effort is required in order to keep the copper loss low. A parameter study with a neuronal network model based on real process data was conducted to identify parameters impacting on the copper loss in the slag. It could be demonstrated that the main parameters responsible for copper loss in the final slag are fixed parameters of the flash furnace. For a better understanding of the copper loss in the electric furnace microscopic analyses of the slag structure and viscosity measurements were performed. Based on these results the reduction and settling of the copper containing droplets could be increased in both pilot plant studies and industrial scale. 4

Jan 1, 2007