Search Documents

By G. M. Hutt

Introduction The major development of industrial minerals in Manitoba has been in building materials. 'The building-stone industry is developed far beyond the needs of the Province, and the well known Tyndall limestone is marketed over a wide area throughout the other provinces to Canada. Similarly, gypsum and gypsum products are produced in excess of local requirements and are exported to adjacent provinces. The crushed-stone, sand and gravel, limestone, and lime industries are sufficiently developed to supply the needs of the Province and, notably in the case of lime and lime-stone, there is a surplus for export to the adjacent provinces and to the United States. The manufacture of common brick is well established, but for face-brick and other clay products the Province is dependent largely on importations. Production of silica-sand will increase as Canadian markets become available through recognition of the utility value of the Black Island sand as foundry-sand and for other purposes. There is some possibility of the export of feldspar, of lithium ore and concentrates, and perhaps of salt. A considerable part of the Province has not been seriously prospected for industrial minerals and it may be expected that, as time goes on, other deposits of non-metallic minerals will be discovered and opened up, especially as the prairie provinces become more industrialized. At the present time, there is some activity in the southern part of the Province based on gas and oil indications. Whatever may be the outcome of this work, it should yield valuable information concerning the geological structure of the area.

Jan 1, 1934

By E. Dalgaard

During linear friction welding of titanium alloy Ti-5A1-5V-5Mo-3Cr (Ti-5553), the weld zone exhibits beta (B) grain refinement and alpha (a) phase depletion that have the combined effect of deteriorating the mechanical performance of the weldment. In this work, linear friction welded Ti-5553 was subjected to pre- and post- weld heat treatments in order to determine the conditions under which a phase depletion could be mitigated in the weld zone and thermomechanically affected zone (TMAZ). The mechanical response of the welded samples to the heat treatments was determined by performing tensile testing at room temperature. While the pre-weld heat treatments had no significant effect, the post-weld heat treatments were instrumental in restoring the strength of the starting (heat-treated) material.

Jan 1, 2011

By E. Rezazadeh Azar

Dump trucks are the main mean for hauling earth material within and outside of the construction and open-pit mining jobsites. The real-time monitoring of the material transportation trips is beneficial for proactive equipment management, volume estimation, and productivity measurement. The traditional manual observation is tedious, non-real-time, and expensive; therefore remote sensing technologies, namely GPS and RFID, have been employed for this reason. Ordinary construction videos are another costeffective alternative to monitor dirt loading and hauling operations in real-time. A vision-based system has been developed to recognize and count hauling trips. This system has three modules including object detection, tracking, and action recognition. This system processes videos taken from access roads in which it recognizes dump trucks and then tracks them throughout the viewfinder. The action recognition module is designed to reject false alarms and also terminate tracking. This way, the system is able to count the number of hauling trips and also record the time between each trip. Several state of the art computer vision algorithms were employed to develop this system. Some of these algorithms were modified using spatiotemporal information to minimize the inherent errors of the vision-based methods. The experimental results showed considerable performance of the system for practical application in the construction and mining sectors.

Aug 1, 2013

By Constantin D. Pitis

?Demand-side measure" means a rate, measure, action or program undertaken to conserve energy or promote energy efficiency?? (BCUC, 1996) In actual economical environment, business sustainability requires high-efficiency technological processes. That is why the efficiency concept has to be present at all levels of industrial activities. Nowadays, some purchasing decisions are still driven predominately by the purchase price, in spite of the evidence that such price represents up to 5 % to 7 % of the total costs of ownership with full consequences of energy efficiency and the impact on total ownership costs. The paper presents essentials of converter types and basics of the Global Efficiency (GEff) Concept that has been promoted over the last few years in South African industries (Pitis et al., 2006/7). GEff concept is proven as a useful tool used on price-efficiency decisions. Theoretical and technical aspects of this concept were substantiated with case studies. First part presented in this paper will describe how GEff concept was used on price ? efficiency decisions when single input or direct converters and systems (considered as low value equipments) have been replaced. Besides the impact of energy savings and new innovative developments, the paper suggests general other benefits of: ? Technical and economical performance improvements and competitiveness of mining corporations to international standards; ? Defusing incipient energy crisis in the sector; ? Improving environmental conditions; ? Creating new job opportunities in mining sector. Proposed concept in this paper could be further developed as models of improving companies? corporate energy policies.

May 1, 2010

By Dharmendr Kumar, Pradip, Sivakumar Subramanian, Beena Rai, Venugopal Tammishetti

The separation efficiency in a mineral processing plant is generally assessed and reported in terms of elemental assays constituting the minerals of interest. However, different minerals comprising of same elements behave differently under similar process conditions. Thus, it is imperative to track the mineral composition thank elemental composition of different streams in a processing plant. The availability of automated mineral analyzers such as QEMSCAN and TESCAN in recent times has made it possible. However, due to the high cost and expertise required, their adaptation in day to day monitoring of operations is not yet a common place. X-ray diffraction (XRD) profile fitting (Rietveld Refinement) is another technique which can provide estimates of mineral proportions in a sample. The results of Rietveld Refinement however are affected by coating of fines on coarse particles, method of sample preparation, particle size distribution of sample, elemental substitution in mineral crystal lattice. In the present work, we propose a simple and efficient method for quantitative estimation of minerals in iron ores using elemental assays and thermo-gravimetry analysis data. The minerals (hematite, goethite, gibbsite, kaolin and quartz) are identified using powder XRD analysis. It is also observed that goethite contains Al substitution in the crystal lattice. The samples were analyzed for %Fe, %Al2O3 and %Silica using chemical analysis. The measured Loss on Ignition (LOI) in the sample is contributed from goethite, gibbsite and kaolinite phases. LOI from gibbsite and goethite occur in temperature range 250–350°C and LOI from kaolinite occur in temperature range 400–700°C. According, LOI are determined in two different temperature ranges that are 100–400°C and 400–850°C. We have used the data to successfully determine the mineral compositions of iron ore samples. We have also employed a data reconciliation algorithm on the calculated data for further improvement and consistency of our results. Our method is very convenient for quick estimation of mineral proportions in a sample. The proposed method can also be used for quantitative phase estimation in bauxite ores and red muds.

Jan 1, 2016

By Gerald R. Larocque, Donald F. Grenville

"IN APRIL, 1965, the employee relations department (then called the personnel department) was established as a separate function within the company. Its aims and objectives were to hire an effective work force to operate the open-pit mine and the mill, which were at that time under development and construction. It was also directed to develop a sound policy for employee relations to assist the company in maintaining a stable and properly motivated work force, which included the establishment of satisfactory wage rates and fringe benefits, safety, fire protection and security. During the 8 years that the department has been in existence the scope of the company's operations has expanded to include a zinc plant and an underground mine. The work force has enlarged accordingly and now totals 1,680 employees working at the two sites, separated by 34 road miles. To cover the employee relations functions the department has a total of 29 members at the two sites. The department is organized under a superintendent, who has an employee relations supervisor, a safety director and a fire chief reporting directly to him. The employee relations supervisor, with 2 employment officers and 2 clerks, handles hiring, first-stage employee grievanoos, terminations, employee records, and the organization of company-sponsored functions and meetings. Safety, training and security are the responsibility of the safety director, who has 3 safety supervisors, 16 security men, 1 first-aid attendant and one hearing conservation technician to service the two sites. The fire chief operates as a one-man section responsible for plant-wide fire inspections and fireoriented training. Although"

Jan 1, 1974

By M. Walawalkar, C. K. Nichol, G. Azimi

Rare earth elements (REEs) are essential to the production of technologically advanced products, including wind turbines, electric and hybrid cars, automotive catalytic convertors, hand held electronic devices, and military defense systems. Their application in environmentally beneficial technologies puts them at a high priority for ameliorating environmental concerns. Because of their increasingly high demand and limiting resources, it is highly beneficial to find new sources for them. The present study is focused on leaching REEs from a phosphate based fertilizer by-product, known as phosphogypsum (PG). Global estimated world production of PG is about 240 million tonnes that is stored in the form of wet stacks adjacent to fertilizer production facilities, occupying vast amounts of land. PG also contains trace metals, which are detrimental to the environment, and hence it is crucial to monitor these stacks. We obtained our PG sample from Agrium Inc. (a fertilizer manufacturing company in Canada). We performed a comprehensive characterization of the PG sample and found that it predominantly contains Y, La, Ce, Nd, and Sm. For leaching purposes, we used hydrometallurgical acid leaching techniques. We investigated three acids over a range of operating conditions such as acid concentration, temperature, solid-to-liquid ratio, and residence time. We achieved an average leaching of 81% with hydrochloric acid as leachant using operating conditions that can be easily replicated in industrial settings. If our process is implemented, not only will it reduce the size of the existing PG stacks (mitigating their environmental risks), but also enable the development of new innovative routes for extracting REEs, making countries like Canada less vulnerable to supply disruptions.

Jan 1, 2016

By M. Turek

Cost management in the conditions of increasing competition and unforeseen market turbulence constitutes one of the key areas of the enterprise?s activity. In the last two years the demand for hard coal on the domestic and global market of non-renewable resources has increased significantly. Polish hard coal mining industry, as an industry in the stage of decline, received a chance for rejuvenation. However, one of the most significant conditions of seizing this opportunity is the rationalization of mining costs and improvement of production effectiveness. Due to the significance of this issue, the main objective of the paper is to identify the possibilities of improving the production effectiveness in the hard coal mining industry. In order to meet such an objective, in the first part of the paper we measured effectiveness in the Polish hard coal mines in years 2006- 2011. The research encompassed three out of five mining enterprises operating in the country. Then based on the received results, guidelines concerning the improvement of effectiveness of production were created, taking into consideration infrastructural, technical, economic and organizational determinants. Furthermore, opportunities and threats for improving the production effectiveness, stemming from the external conditions have also been indicated.

Aug 1, 2013

By James K. Gowans

"Cominco Ltd's Polaris Mine, located on Little Cornwallis Island, Northwest Territories (latitude 75degrees 30') went into production in late 1981, becoming the world's most northerly base metal mine. The concentrator, powerhouse, shops, offices, dry and warehouse, were uniquely designed and constructed on a 100f t wide by 400 ft long by 65 ft high barge. This process barge was constructed in southern Canada at Trois Rivières, then towed 3,500 miles into the High Arctic Islands and beached on Little Cornwallis Island.The paper deals with the original design philosophy, flowsheet and the initial year's operation of the Polaris process barge.IntroductionTo bring a mining property into production in the Canadian High Arctic, a company must deal with the harsh environment, the short shipping season and the high cost of labour. In trying to minimize the effect of these fact or s, the concept of a barge-mounted process plant was investigated as an alternative to the conventionally built concentrator. Cominco's previous experience gamed at the Black Angel Min e on Greenland's west coast suggested that this would be a practical alternative.The normal shipping season at Little Cornwallis Island is approximately six weeks long, from mid-August to the end of September. All equipment and materials must be delivered during the ""shipping window"". The logistics problems are enormous; if the conventional approach had been used the major process equipment would have been delivered to Little Cornwallis Island at the same time as the completed barge actually was! Construction would also be starting at the start of the worst climatic conditions, the Arctic winter. Nine months' production was gained by opting for the ""barge"" approach."

Jan 1, 1983

By A G. Rogers

This paper discusses the lubrication of surface and underground mining machinery and equipment from the standpoint of machine components. The machine components considered are bearings, cylinders, gears, chains, couplings, fluid drives, hydraulic systems, screws and wire ropes. The best selection of lubricants for these machine components, and for sub-divisions of the components, are outlined. They form general recommendations, for average operating conditions in both surface and under-ground mining operations. The American Petroleum Institute's service classification of both engine crankcase oils and gear oils is de-scribed and used in recommending products for these applications. The practical aspect of lubrication is kept foremost in the recommendations, which are designed to meet the requirements of a wide variety of equipment with the minimum number of lubricants. THE lubrication of mining machinery and equipment presents a variety of problems peculiar to the industry. The type of mine, the ambient temperature, water, dust, and operating and maintenance practices, as well as the age and condition of the equipment, are variables which have to be considered in making lubricant recommendations.

Jan 1, 1963

By Hassan El-Shall, Ayman El-Midany, Patrick Zhang

Bench and pilot scale testing results suggest that significant improvement in dewatering characteristics of fine particles could be obtained by the addition of fibrous materials. Case studies involving flocculation and dewatering of wastes from phosphate, bauxite, and kaolin processing plants are presented in this paper. Several dewatering techniques were investigated, including sedimentation thickening, filtration, centrifugation, dewatering on screens, and seepage-induced dewatering and consolidation. Advantages and limitations of commercial application of some of the developed techniques arc discussed.

Jan 1, 2004

By D. J. Lucifora

Monitoring-While-Drilling (MWD) is a proven technique that records instantaneous on-drill parameters which can be used to supply contextual information for in-situ, down hole conditions, such as: changes in geology, the presence of pre-existing fractures and dynamic alterations, down hole conditions including bit bailing, bit blockages and bit wear, and improper drill operation. This technique has been widely used in the oil and gas industry and, eventually, it was transferred to the mining industry. A challenge when analyzing and interpreting MWD data is in utilizing proper filtering which enables one to properly eliminate any ?noise? from the signals of interest. Overall the importance of MWD data is that, through the collection of operational field-based data, a dataset can be acquired which allows experimentation and analysis to be carried out. Such a dataset is often impossible to replicate in a laboratory setting. If successful, and through iterative refinement, any promising method can eventually be implemented on-machine and using real-time monitoring techniques. This paper will provide a state of the art review of presently used MWD techniques and applications in industry. The paper?s primary focus will be on shallow, mining-style, blast hole drilling but will also take into account techniques and applications utilized in oil and gas drilling which have not been adopted in the mining industry. In the cases where MWD techniques and applications exist solely in oil and gas drilling the paper will examine and comment on the potential utility of technology transfer to mining applications.

Aug 1, 2013

By T. S. Smith

INTRODUCTION IN PREPARING this paper for the District 4 Meeting, three factors had to be considered. First, the paper must fit the time alloted; second, it must give a general picture of the geology for those unfamiliar with the property; and third, it must contain some new material in order to be of interest to local delegates. The most comprehensive extant discussion of the geology of the property of McKenzie Red Lake Gold Mines, Limited, is contained in Horwood's report on the general Red Lake area ( 1). This report is the 'bible' of the area, and a general paper on the geology of this particular mine would almost certainly appear to be a condensation of it. It was thought, therefore, that the most suitable procedure would be to base the general outline on Horwood' s report, to extend that outline where possible from information gained since its publication, and finally to leave dangling for the contemplative geologist some of the ideas and problems which ?are currently under consideration. LOCATION AND HISTORY The property of McKenzie Red Lake Gold Mines, Limited, is in Dome township, in the Red Lake mining division of northwestern Ontario. The mine is on McKenzie Island, about four miles north, by water, of the Hasaga mine and old Howey mine.

Jan 1, 1951

By Roorda H. J, R. R. Saddington, Curlook W

THE copper-nickel sulfide ore deposits of the International Nickel Company of Canada, Limited contain the minerals pyrrhotite, pentlandite, and chalcopyrite. In the extraction of the nickel, copper, and iron, much of the processing involves oxidation of the metals as well as sulfur. Roasting plays a predominant role at several stages in the operations which prepare the constituent metals for refining. Copper, nickel and iron concentrates of various grades, ranging from low-grade nickeliferous pyrrhotite to high-grade nickel sulfide, must be partially or completely oxidized. Figure 1 shows the main points at which roasting is conducted at INCO. Roasting experience at INCO dates back to the time when lump ore was partially roasted in heaps. It has progressed through single hearth roasters, sinter machines, multiple-hearth roasters, flash roasters, and more recently has centered on the development and utilization of fluid bed roasters. The primitive, slow, and inefficient method of heap

Jan 1, 1961

By Thomas Mütze, Frank van der Meer, Gunnar Kretschmar

"The air classification of moist bulk materials is addressed in the literature insufficiently. Therefore a feasibility study investigated the influence of feed moisture on the separation efficiency expecting a reduction with higher moisture content in the feed. Two iron ore samples were characterized in terms of the nature of bonding of moisture as well as its effect on the agglomerate strength. The classification tests themselves were conducted with two dynamic laboratory air classifiers at cut sizes from 45 to 110 µm and a moisture of the feed material between 0 to 10 wt.-%. The quality of classification was assessed by split factor, cut size, separation efficiency, moisture of both products, as well as the yield of the fines as product fraction in a corresponding processing plant. An initial approach was found for a technological implementation: A sufficient drying of a moist feed can be realized simultaneously to the pneumatic transport inside the classifiers. In the present case the drying effect and dispersion intensity was sufficient to provide good separation results up to 3 wt.-% feed moisture. An additional drying step was necessary beyond 3 wt.-%.INTRODUCTIONSpecific information about the influence of moisture in air classifiers is very rare. Mostly only dry products are processed and/or drying prior to classification is recommended. Apart from the specific influence of the feed moisture a lot of literature can be found regarding air classification itself. Altogether air classification can be divided into several sub-process (Leschonski, 1977):- dosage of the feed material,- dispersing the solid feed material into a gas stream,- feeding the dispersed material into the classification zone by pneumatic conveying,- separation of coarse and fine particles, and- separation of fine particles from gas.For wet feed particles also drying plays an important role. Interesting for the present investigation are the humidity of the feed and its influence on the single sub-processes."

Jan 1, 2016

By R. E. G. Caines, P. Alport

"Operating heavy equipment in Labrador, where the winters are 8 months long and the temperature frequently drops below -40°F (-40°C) for days and sometimes weeks presents unique problems in both the operation and maintenance junctions. Winterization programs must be well designed and implemented at the proper time. These programs must include the proper selection of fuel oil, engine oil, hydraulic oils, greases, cooling system fluids, etc. More often than not, modifications have to be made to the original equipment in order that it can be operated safely and economically in the Canadian North. Manufacturers usually design equipment for a less harsh environment and the user makes adaptations by trial and error.Operators have to be trained for the proper operation on ice- and snow-covered roads in an open-pit mine. Special emphasis must be put on haulage road conditions. In this paper, the authors will cover some specific maintenance procedures, equipment modifications and operator training problems experienced by the Iron Ore Company of Canada in its open-pit operation in Labrador.IntroductionT he Iron Ore Company of Canada is engaged in open-pit mining , concentrating and pelletizing of iron ore. The company operates in two provinces, Quebec and Newfoundland (Fig . 1) . The Knob Lake operation "", based in Schefferville, Quebec, has mine sites located both in Labrador and Quebec . The Caro l Lake Project is situated in Labrador, 25 kilometres east o f the Quebec border at Labrador City. The Carol operation mines, concentrates and pelletizes it s o re before rail transportation to the seaport o f Sept-lies via the Quebec North Shore and Labrador Railway."

Jan 1, 1984

By J. B. De Hart

This paper has been confined to the consideration of the working of thick seams, from six feet to sixteen feet, which are pitching at about thirty degrees to the horizontal. The discussion has been limited to these set conditions because they are the ones of commonest occurrence in the Southern Alberta bituminous coal district, because, from the point of view of safety, thin seams are more easily worked, and because a discussion of all the possible combinations of thick and thin seams pitching at angles varying from zero to ninety degrees with the horizontal would involve a task impossible in the time available. It has been assumed that the mine makes gas freely and that the coal is friable and tends to make inflammable dust which is highly explosive. Since the problem requires the taking into account means of maintaining a high proportion of lump coal, it is further assumed that lump coal commands a price considerably higher than the price which can be obtained for run-of-mine or for slack coal. Figure 1, tabulating the various factors which must be considered and their relation to each other, indicates diagrammatically the complexity of the problem. Any method of working becomes divided into two distinct components, the active workings of the mine and the old abandoned workings. While these are in a measure distinct, they are nevertheless inter-related, as shown in the diagram.

Jan 1, 1930

By R. P. Chapman

The geochemical interpretation of results of statistical analysis of published multi-element stream sediment data from southwest and northern New Brunswick is presented. Element concentrations in southwest New Brunswick are low and comparable to element concentrations in background areas in northern New Brunswick. Deposits of copper and nickel are indicated in southwest New Brunswick. Anomalous element concentrations occur in several areas in northern New Brunswick and the elements most commonly associated with these anomalies are Cu, Pb, Zn, As and Ag; and also Mo, Wand Sb. Bedrock geology greatly influences element concentrations and may cause false anomalies. Manganese has a pronounced effect on the dispersion patterns of Co and also Zn, Mo, Pb, As, Ba and Ni. Nickel and Cr are strongly sympathetically related and this association is independent of bedrock type.

Jan 1, 1977

By P. K. Kaiser, C. D. Martin, F. Amann

"This article focuses on the uniaxial compressive strength (UCS) of homogeneous and heterogeneous rocks. Critical factors impacting the UCS of rocks are reviewed and then separate assessments of UCS data from homogeneous and heterogeneous rocks are presented. The variability (coefficient of variation) of UCS test results for homogeneous rocks is found to be generally <25% while for heterogeneous rocks the variability is >35%. Failure mode variation is found to be the cause of the variability of UCS test results in heterogeneous rocks. Empirical engineering design methods that use UCS as an input parameter are discussed and suggestions are provided for selecting appropriate UCS values.INTRODUCTIONThe UCS is one of the most commonly used rock engineering parameters whether for rock mass classification or for strength determination. The mean UCS and its variability are often assumed to represent a reliable rock material property. For the reasons discussed in this article, UCS is rarely representative of the intact rock UCS. The UCS test simply records the collapse load during uniaxial loading of a cylindrical specimen. As suggested by many, the UCS is an index rather than a unique engineering parameter. The UCS is thus a proxy for rock strength which depends on the loading rate (e.g., Bieniawski 1967), specimen geometry (e.g., Hudson et al., 1971), specimen size (e.g., Bieniawski 1968), and many other factors. Furthermore, the UCS is not the same as the Hoek-Brown strength criterion parameter sci.There are differences in opinion on what is commonly considered to be ‘intact rock’. When sampling ‘intact’ pieces of core from drillholes crossing blocks of rock bound by block forming discontinuities, samples will be ‘intact’ but some samples will be veined, others will be damaged, and others will be neither. According to Hoek (1983), intact rock pieces are “the unfractured blocks occurring between structural discontinuities in a typical rock mass” and the sci parameter for intact rock is determined using the fitting procedure proposed by Hoek and Brown (1997) based on the data requirements outlined by Hoek (1983). Studies (e.g., Bewick and Kaiser 2014; Kaiser and Kim 2014) have shown that independently determined UCS and sci values for the same rock type are not equivalent. Thus, UCS data cannot be used as a replacement for sci."

Jan 1, 2015

By W. L. Nelson

The orebodies at Copper Mounta1n lie along and within a few hundred feet of the contact of an intrusive stock of gabbro with a series of bedded volcanic rocks of the Nicola formation. These. orebodies are all entirely within the volcanic series but in many cases the centre line of the orebody at depth is directly under the gabbro contact at the surface, due to a slight overhang of the gabbro. The gabbro and volcanic rocks are cut by a number of faults and fault zones which did not materially affect early mining operations, but, as undeground openings increased in size, the faults became more important factors in determining mining methods and procedure. Caving methods were adopted to take advantage of ground weakness in fault zones, and the effect of ground subsidence which resulted from the division of the ground 1nto large, independent blocks by faulting had to be considered in planning the sequence of mining of certain ore blocks. The faults have been divided into two classes: the longitudinal system and the cross faults, or &apos;breaks&apos; as they are termed locally. In addition to the two classes of faults, the zones of parallel ore fracture also control mining procedure, but to a lesser degree, in regard to caving or ground subsidence. A third structural feature which influences mining procedure is the mine dyke system. The longitudinal or main fault system roughly parallels the gab? bro contact and is made up of a number of branches and auxiliary fractures. The main fault itself is essentially vertical, but there are a number of branches and fractures on each side of it which, though parallel m strike, may dip as flat as 50 degrees toward or away from the main fault. The full width of the main fault system has not been determined, but it is known to extend beyond the zone of mine workings. A marked schistosity follows the main fault and both schistosity and chloritic alteration have been noticed along the secondary faults of this system. Several prominent orebodies lie along the main fault and its branches. The influence of the main fault system on mining is probably related more to subsidence than to actual cavi.ng, although it is effective in both.

Jan 1, 1950