Search Documents

By R. A. Parra, Fuentes, C. Godoy, L. E. Arias, C. A. Toro, M. Marin, E. Balladares, V. Parra, G. Reyes, S. N. Torres, D. Sbarbaro

In this paper, we report on the detection of spectral molecular emission of iron oxide (FeO) and copper oxide (CuxO) emitted by reactions occurring in a laboratory scale flash smelting process of pyrite (FeS2) as well as copper concentrate. The novelty of the technique is that, the molecular spectral emission sensing is achieved by using a low spectral resolution and low sensitive radiometer, enhanced with signal processing and matrix factorization techniques. The method was validated using a highly sensitive spectrometer, with a high spectral resolution; achieving a similar FeO spectral pattern as the one obtained after signal processing techniques over low resolution spectral signals. INTRODUCTION Visible-near infrared (VIS-NIR) spectroscopy is an optical contactless sensing technique commonly used to capture information about the emitted, absorbed, transmitted or scattered radiation in a physical or chemical process, with the presence or absence of an excitation light source such as a laser or a broad spectral band source. These techniques coupled with signal processing and machine learning algorithms, sometimes referred as chemometrics (Pisapia et al., 2018), can be found in processes such as: pharmaceutical (Kandpal et al., 2016); food (Coelho et al., 2016); combustion (Ballester & García-Armingol, 2010); siderurgy (Strakowski et al., 2014) industry, among others. In the extractive copper industry there are several technological developments using optical sensing techniques aimed to retrieve information about copper ore and concentrate mineralogical composition such as X-Ray Fluorescence, Qemscan® (Quantitative Evaluation of Minerals by Scanning Electron Microscopy) and X Ray Diffraction (XRD) analysis, however, because of the manual procedures to analyze the samples with these laboratory instrumentation, only discrete information during a daily based operation can be retrieved, making impossible for the operators to take decisions over the involved processes in real time. The aim of our research work presented here is to contribute with sensing and data analysis procedures based on VIS-NIR spectroscopy for the flash smelting process characterization, particularly in this paper, with the detection of FeO and CuxO molecular emissions in a laboratory scale setup.

Jan 1, 2019

By M. Sommerfeld, U. Schwarz-Schampera, B. Friedrich, D. Friedmann

The steadily growing demand for metals and their price increase at metal exchanges make the mining and utilization of marine mineral resources like polymetallic nodules, manganese crusts or sulfide deposits in the near future a viable option to potentially increase the supply of base and precious metals. For a country with low potential to mine land-based resources like Germany, the industrial recovery of metals from marine mineral resources could lead to a decreased dependency on imports. In this study, seafloor massive sulfides from the German license area in the Indian Ocean (Kairei field, Southern Central Indian Ridge) are treated to recover copper and precious metals. The aim of the project is to demonstrate the transferability of existing metallurgical techniques to the raw material of deep-sea massive sulfides. As a starting point to process this unconventional resource, samples from the Indian Ocean are chemically analyzed and mineralogical characterized. A comparison is carried out between the samples and land-based copper resources, to highlight the potential which lies in mining the deep-sea floor. This paper will show the general possibility of applying a two-stage pyrometallurgical process, based on a concentrate smelting operation, followed by a converting operation in lab-scale to the provided samples of massive sulfides. Generated slag from the concentrate smelting and the converting operation are investigated by X-ray diffraction to determine the mineralogical composition. The two-stage pyrometallurgical process is investigated by the thermochemical modelling tool FactSageTM 7.2 to evaluate the phase distribution of relevant elements between the metal, matte, slag and gas phase. The thermochemical boundaries of the pyrometallurgical process are therefore set and the results of the thermochemical study can be used as an indicator for the efficiency of an up-scaled process and the generated amount of side-streams, which need to be further treated or circulated back into the process. INTRODUCTION Seafloor massive sulfides (SMS) are the third kind of discovered deep-sea minerals besides ferromanganese nodules and cobalt-rich ferromanganese crusts (Sharma, 2017). They occur in water depths around 250–4,000 m (Koschinsky et al., 2018). SMS are characterized by a high base metal and sulfide content. They were created by fluid circulation and hydrothermal convection over time (Han et al., 2018). Commonly, areas rich in SMS are associated with hydrothermal vent fields on the seafloor (Keith et al., 2018).

Jan 1, 2019

By W. Díaz, R. A. Parra, L. E. Arias, C. A. Toro, M. Marin, E. Balladares, V. Parra, G. Reyes, S. N. Torres, D. Sbarbaro

This work presents visible-near infrared (VIS-NIR) spectroscopy measurements, and signal analytical techniques to characterize minerals and relevant pyrometallurgical process variables for the copper extractive industry. Data signal processing techniques such as baseline correction and numerical analysis are used to estimate the continuous and discontinuous spectral components. Such spectral components are used to estimate the process temperature, and patterns such as the integrated radiation. Also, metal combustion emissivity calculation are depicted. Our findings suggest that VIS-NIR spectroscopy may be a suitable technique to assess the process condition state, appearing as an interesting sensing alternative. INTRODUCTION Although the flash smelting process is one key stage in the copper extractive industry, representing about 40% of copper matte production worldwide (Cantallopts, 2017), few attention is dedicated to develop sensing solutions to assess process variables, such as mineralogical composition and temperature, in the feeding and bleeding stages, compared to the steel industry (Strakowski, et al., 2014). In this process and other industries, e.g. the thermoelectric power generation one, combustion and particularly the generated flame are the production chain’s heart. Since the flame is a highly radiative emitting process where chemical and physical transformations take place, many works had been dedicated to characterize the combustion state by sensing its radiation using optical and photonic technologies (Ballester & García-Armingol, 2010). In this context, this work aims to contribute with visible-near infrared (VIS-NIR) spectroscopy and pyrometry techniques to retrieve relevant information from a laboratory scale flash smelting process. On the other hand, since photonic instrumentation allow us to perform contactless measurements of emitted, absorbed, transmitted or scattered radiation, it appears as a suitable technique for sensing process properties in harsh environments, e.g. high temperature processes. One of these techniques is the Visible- Near Infrared (VIS-NIR) spectroscopy, which provides information about the spectral radiation intensity distribution, in this work, the emitted flame’s radiation. It is well known in combustion research that the spectral emission from a flame is composed by a black body continuous radiation background, molecular emissions, elemental emissions and additive noise features (Arias et al., 2011). To make sense of such information signal processing techniques are needed, here we propose to analyse the continuous and discontinuous spectral components separately.

Jan 1, 2019

By M. Elmadagli

Wear mechanisms of two commercial aluminum alloys, namely a spray formed and extruded Al-25%Si alloy, and a sand cast A390 alloy (18.5 %Si) that are known to be successful in cylinder bore technology were studied to have a better understanding of the requirements for wear resistant aluminum alloy design. From durability point of view these alloys are known to be successful for engine bore applications. It is interesting to compare the wear mechanisms in these alloys because they have significantly different silicon content and microstructures, and were produced using different techniques. The wear tests were done using a block-on-ring configuration, in controlled air atmospheres (5 % relative humidity). In spite of the differences in silicon content and microstructure, the wear mechanisms were similar and consisted of formation and destruction of hard tribolayers that are either formed by either mechanical or chemical interactions on contact surfaces. The differences in the wear rates between the two alloys arose from the differences in the hardness of the worn surfaces, and the alloy's ability to sustain the tribolayers on the worn surfaces.

Jan 1, 2004

Between 1993 and 2003, a series of AG and SAG mill pilot plant trials were conducted using Hardinge Ical pilot plant scale SAG mills on numerous ore samples and ranging across a wide variety of operating conditions. The data from these tests were used to evaluate the design of SAG and AG mill circuits for over a dozen projects, of which about half were eventually constructed and commissioned. The data were also used in the development of SAG mill modelling, scale-up and simulation procedures by several consultants who had access to part of the data set. Recently, we have had the opportunity to bring this data together and further analyse the consolidated dataset. This paper reports on the outcomes of this analysis that has identified the impacts of different AG/SAG circuit flowsheets and operating conditions on energy efficiency and operating cost.

Jan 1, 2012

By Constantin Pitis, Paul Slatter, Behnam Pirouz, Laura Contasti, Markus Zeller, Sadegh Javadi

"The centrifugal slurry pumps feeding cyclones are critical components used in the grinding process. It is well known that for this type of pumps the performance degradation is very intense. To minimize downtime a complete stand-by slurry pump is always installed in a parallel circuit. The replacement decision of slurry pumps is sometimes set on specific periods of time that are empirically determined, based on previous experience; unless a pump failure triggers the second (standby) pump. Given the significant energy costs in the grinding process and a desire to increase competitiveness, engineers and scientists started research in this field while manufacturers also took actions in order to improve pumps reliability and performance. The lack of standardization regarding the methods used to benchmark and evaluate the energy performances of cyclone slurry pump systems in the mining industry makes it difficult for an enterprise to take informed decisions concerning the replacement or optimization of its process based on energy benchmarking of such slurry pump systems. This paper proposes a new methodology of benchmarking slurry pump performances using a new concept of Benchmark Energy factor (BEF) based on Mathematical Model Benchmarking. The concept of BEF has been proven successful in other industries. A new standard addressing the guidelines for benchmarking the energy performance of slurry pumps for cyclones was proposed within the Canadian Standards Association. This standard will provide a unified and consistent methodology for performing measurement activities with the ability to measure and verify the system energy performance in the field through the BEF approach. Practical examples based on the new concept are presented with comments."

Jan 1, 2017

By K. Webb, M. Hohn

"This paper reviews the evolving Ontario mining regime for mining industry-Aboriginal engagement and its apparent alignment with court decisions, domestic law, emerging international norms, mining industry rules, and mining firm-Aboriginal agreements, drawing on publicly available commentary from government officials, the private sector, and Indigenous communities. This paper provides a preliminary analysis of the potential implications of the new regime, especially for the mining industry and Aboriginal communities and, on that basis, discusses possible future developments.RÉSUMÉ Le présent article analyse le régime minier de l’Ontario pour l’engagement entre l’industrie minière et les Autochtones et son harmonisation avec les décisions des tribunaux, le droit interne, les nouvelles normes internationales, les règles de l’industrie minière et les ententes compagnies minières- Autochtones en se basant sur des commentaires, disponibles publiquement, d’officiels gouvernementaux, du secteur privé et des communautés autochtones. Cet article fournit une analyse préliminaire des implications potentielles du nouveau régime, surtout pour l’industrie minière et les communautés autochtones et, en s’appuyant sur ces données, il traite des futurs développements possibles."

Jan 1, 2016

By F. H. Samuel, H. Tahiri, S. Valtierra, H. W. Doty, A. M. Samuel

L'affinage des grains dans les alliages d'aluminium consiste à augmenter le nombre de sites de cristallisation de la phase a-Al afin d'obtenir une structure fine. Les alliages mères de type Al-Ti-B sont largement utilisés comme raffineurs des grains. Cette étude a pour but d'établir des mécanismes convenables d'affinage des grains dans l'alliage A356 en utilisant cinq alliages mères et deux températures de coulée (750°C et 950°C). Les résultats montrent que la phase a-Al prend une forme selon l'alliage mère ajoute; les échantillons coules a haute température montrent une taille de grain plus grosse; les températures de germination et de croissance augmentent avec I' augmentation du Ti ou du B et la taille des grains diminue. L'alliage mère Al-4%B montre une puissance remarquable en comparaison d'autres alliages mères. Pour cet alliage mère, le titane résiduel dans l'alliage A356 réagit avec le bore pour former TiB2 qui, par la suite, agit comme un germe actif pour la phase a-Al.

Jan 1, 2006

By N. Ogbonna, D. G. Dixon

Although heap bioleaching has been recognized as an economic alternative for treating low grade mineral ores, the underlying physical, chemical and biological processes involved are complex. A detailed investigation into the dynamics of heap bioleaching processes has provided much insight into the underlying complexities, and has led to the development of a sophisticated modelling tool - HeapSim. This tool can be of great help in the design and operation of heap bioleaching processes. In this paper, the mathematical model implemented in HeapSim is examined. The model takes into account mineral kinetics, particle level effects, bacterial growth, oxidation and adsorption, gas absorption, pore diffusion, bulk advection, gas balance and heat conservation. Three case studies where the model has been applied are briefly discussed. Computational Analysis in Hydrometallurgy 35th Annual Hydrometallurgy Meeting held in conjunction with the 44th Annual Conference of Metallurgists of CIM Calgary, Alberta, Canada Edited by

Jan 1, 2005

By S. F. Guo, Z. F. Zhan, X. L. Huang, Y. Zou, S. W. Qi

"FLAC3D is an important numerical analysis software to study dynamic response of rock slope. In application of the program, the common issues such as absorbing boundary and the method to apply wave have been well studied. However, effects of model mesh size, damping and width of slope are still unknown. In order to make the result more convictive, this article has discussed the above issues systematically. It found that when the maximum mesh size is smaller than 1/10~1/8 of the smallest wavelength, the mesh size is smaller, the computational accuracy is higher. Meanwhile, values of damping and width of slope have no effect on the result. Additional, results of FLAC3D modeling on wave transmission across rock joints agree well with analytical solutions, so it has verified the capability and accuracy of FLAC3D on dynamic response of rock slope.INTRODUCTIONChina is a mountainous country accompanied with many earthquakes. Thousands of geological disasters are triggered by the Wenchuan Earthquake in Sichuan Province, and the majority of the disasters are landslides induced (Xu et al., 2009). Meanwhile, the paper (Li et al., 2003) points out five significant issues about dynamic loading in the area of geotechnical engineering, which includes the study of rock slope stability under earthquakes, and the dynamic response of rock slopes is one of its important study issues."

Jan 1, 2015

By Y. Nara, N. Aramaki, M. Maruyama

Evaluation of three dimensionally non-uniform strain distribution in rocks under various conditions such as in water or under freeze-thaw cycles is of significant importance to understand their complex deformations and fracturing mechanisms. For this purpose, we developed an image analysis method which can evaluate or “measure” the three dimensional (3-D) strain distribution in rocks. The proposed method utilizes the 3-D images of rock under initial and deformed configurations, which are obtained by some imaging techniques such as X-ray computed tomography (X-rayCT). In the proposed method, the obtained 3-D images are divided into multiple sub-regions of interest. For each sub-region, the strain is evaluated utilizing 3-D affine transform with unknown coefficients to be determined. In the first step, 3-D voxel level displacements at multiple representative points in each sub-region are computed by 3- D digital volume correlation technique between the comparison images and the initial-guess of the transform coefficients are obtained. In the second step, referring to the initial-guess of unknown transform coefficient, they were optimized in sub-voxel level by finding optimum digital volume correlation between the comparison images, which can evaluate the transform coefficients with higher precision. From the calculated transform coefficients, the strain was directly obtained through the spatial derivative of displacement based on affine transform. In this paper, along with the description of the proposed method, the evaluation of deformation in a lignite specimen due to immersion in water was presented as an application example. As the 3-D imaging technique, micro-focus X-rayCT was applied. The result showed that the induced dilatational strain field due to the initiation and extension of cracks in the specimen was clearly captured. Therefore, authors believe that the proposed method can be applicable to various problems in rock mechanics.

Jan 1, 2015

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors' thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda's diagram for Cu20-Fe0x-Ca0 ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04. 0

Jan 1, 2007

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors' thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda's diagram for Cu20-FeOx-CaO ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04.

Jan 1, 2007

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The major importance of liners in grinding is their role in providing an appropriate trajectory for the charge. Since it is not possible to study the charge movement by direct observation in operating industrial mills, this task is accomplished by physical (laboratory), and/or, mathematical (software) methods. Because of the high cost and a longer time required for a physical analysis, mathematical simulations have become more common. Simulation of the effect of liner shape on the charge movement has provided a means to select a proper design based on the operational objectives and conditions. Furthermore, the liner shape changes due to wear and impact during operation, which will influence the charge trajectory. This adds more of an incentive to use simulation. These changes in liner could be predicted through liner profile measurements during operation and/or simulation. In this research, an inhouse developed DEM software called KMPCDEM © was used to simulate the charge movement in industrial plant SAG mills. A geometrical method of implementing the shell liners on SAG mills at the Sarcheshmeh (9.75×4.87 m) and the Gole-E-Ghohar (9×2.05 m) operations facilitated the software simulation. Point by point implementation of the measurements of liner profiles of these mills enabled the study to trend the change in the charge movement as the liners wear. Comparison of the simulation to a laboratory mill (1 m diameter) showed that the difference between the measured and predicted charge impact point, shoulder angle and toe angle were 6, 4 and 3°, respectively. INTRODUCTIONComminution is the most energy intensive operation constituting the major portion of operating and capital costs of a mineral processing plant. In the last decade, a vast number of research was aimed at studying various aspects of grinding with the aim of performance improvements (Davis, 1919; Mishra & Rajamani, 1990; kalala, Breetzke, & Moys, 2008). Mill liners transfer the input power to the charge and play a significant role in affecting the motion of the charge (Mclvor, 1983; Mishra & Rajamani, 1990; Radziszewski, 1997; Van Nierop, Glover, Hinde, & Moys, 2001; kalala et al., 2008). Lifters are usually used with mill liners to extend their life and to enhance the grinding and impact breakage efficiency. Mill lifters are used to raise the grinding media and ore to transfer the energy from the mill to the load (Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010)."

Jan 1, 2016

By D Martín, G. Díaz, F. Cubeddu, A. B. Mejias

The Modified ZINCEXTM Process (MZP), developed by Técnicas Reunidas, is an industrially proven flexible process. It can handle a wide range of primary and secondary raw materials, producing SHG zinc. The core of the Modified ZINCEXTM Process is the zinc solvent extraction unit. This unit is an effective barrier for any leachable impurities present in the raw material. As a result of this an ultra-pure zinc solution is always obtained. The high versatility of the process makes the application of the technology in different scenarios possible. MZP can be effectively applied when developing a whole new plant (Skorpion) or adapting its scheme to an existing refinery (Akita), in both cases giving the same results. Flexibility in terms of capacity of the plant is a great advantage of the MZP, there is the possibility to adapt the global process to a wide range of production capacities. Zinc production capacities of over 150 000 t/a may be achieved with a single solvent extraction plant train. The robustness of the Modified ZINCEXTM Process has been recently proven on two new plants currently in operation: Portovesme (Italy) and Horsehead (USA) after start up during 2013. The status of both plants is described in this paper.

Jan 1, 2014

By W. Basuki, B. Setyotomo, L. Hakim, R. Hendrajaya

Due to high crack sensitivity of slab product of gas and oil line pipe application, its steel making process and alloy composition were evaluated and then improved to overcome its critical solidification process and reduced surface defects. The study was conducted at Slab Steel Plant Krakatau Steel. The purpose was to improve slab surface quality by reducing surface defects so that the slab surface doesn't need to be totally repaired. The method applied was by performing plant trial process, which the secondary process parameters such as alloying method and the casting parameters such as casting powder selection, metallurgical cooling, mould level control, and superheat were continuously monitored and then adjusted to the surface quality of the product. Based on the calculation of Ferrite potential of the steel, the chemical composition was designed to achieve optimum casting parameters in order to avoid high shrinkage during solidification. The results of the study are decreased surface defect quantity, and smooth casting process. The quantity of crack decreased by almost 90%. The slab surface repairing was significantly reduced from 85. % to less than 10%. These new casting parameters and developed alloy composition are then used and standardized for the mass production of the steel.

Jan 1, 2005

By T. R. Skerry, H. P. Hudson, T. E. Warren

"ALTHOUGH coal is generally the cheapest fuel on the basis of heating value it has been at a disadvantage in competition with other fuels because means have not been available for efficient •Conversion of its thermal energy to mechanical work. Taking the •railway application •as an example, the cost of Diesel oil is about three times that of its thermal equivalent in coal, but the overall efficiency of a Diesel locomotive is about five times that of a coal-fired steam locomotive. Accordingly, the Canadian railways are replacing all coal-fired steam Locomotives, as they are retired from service, with Diesel units. This conversion in itself represents a major loss to the coal industry because the value of railway fuel is approximately 130 million dollars per year, and there are other applications in the medium power range where oil is displacing coal. There is, therefore, a strong incentive to attempt development of an efficient coal-burning engine.Coal has never been a promising fuel for reciprocating internal combustion engines because of the time required for its combustion in pulverized form . This is not less than one-tenth of a second so that the speed of such an engine would have to be very slow. There are also serious difficulties of a mechanical nature arising from the necessity for intermittent combustion and the use of close-fitting pistons."

Jan 1, 1952

By J. M. Bowen, P. Wemyss

"Gold losses to natural carbonaceous matter during cyanide leaching have been investigated for over a century. The variation in the severity of the problem from one ore to another has led to a range of different processes being implemented at different mine sites. Most commercial options utilise one or more of the following processes: roasting, carbon pre-flotation, organic blinding, CIL, chlorine passivation, pressure oxidation, biological passivation, elevated temperature CIL, RIL and thiosulfate. This paper provides a background to identify the most appropriate process or combination of processes for a particular ore. It also presents information on how these processes may be implemented, drawing on information in the literature and from current or recent applications at operations such as the following: Stawell, Kumtor, Penjom, Twin Creeks, Macraes Flat, Kittilä, Fosterville, Inata, Carlin, Goldstrike, and Jerritt Canyon. Various process options have been dismissed, or deemed unsuccessful due to limited knowledge available on the strengths and weaknesses of the different options and their implementation. The authors have collectively been involved in flowsheet development and project implementation in four commercial plants that have treated preg-robbing ores.INTRODUCTION Cyanide processing has been the mainstay of gold recovery for well over a century. It is generally a very effective process with over 90% recovery on free milling ores, but complex and refractory ores may only give 0–50% recovery with conventional processing (La Brooy et al., 1994). People have written about gold losses to natural carbonaceous matter during cyanidation for over a century e.g. Feldtmann, (1915). The earliest reports related to African operations, but the issue has since been reported in Canada, North and South America, Australia, Russia and China. The phenomenon is usually referred to as ‘preg-robbing’ dating from the times before the use of granular activated carbon for gold recovery, when gold was lost from the pregnant solution before it could be separated from the leach solids and recovered by cementation. Many excellent reviews have been published e.g. Dunn et al. (2013), summarising the options considered and where they have been applied commercially."

Jan 1, 2017

By Grant Arnold

Le Camp Minier de Matagami est situé dans la ceinture volcano-sédimentaire Harricana- Turgeon appartenant à la Province du Supérieur, sous-province de l?Abitibi, au Québec. Les gisements de métaux de base polymétalliques sont retrouvés exclusivement dans les deux domaines lithotectoniques comprenant l?association basalte-rhyolite (Matagami-Brouillan et Joutel-Raymond). Tous ces dépôts, à l?exception de ceux de Selbaie, sont de type exhalatif et représentent des dépôts volcanogènes à Zn-Cu, typiques de l?Archéen. Le complexe volcanique de Matagami est constitué principalement de deux phases de volcanisme tholéïtique. Les dacites et les rhyolites du Groupe de Watson, représentent la phase la plus précoce et celles-cis sont recouvertes par la seconde phase qui est constituée majoritairement de roches intermédiares à mafiques intercalées d?horizons felsiques, formant le Groupe de Wabassee. Un sédiment chimique sulfuré, la Tuffite Clef, marque le contact et l?hiatus entre ces deux groupes. Cette tuffite est reconnue à la grandeur du flanc sud du camp minier et représente l?horizon favorable à explorer puisque sa déposition a correwspond à une période d?intense activité hydrothermale. Le complexe volcanique de Matagami est limité au nord et au sud par des bandes sédimentaires orientées est-ouest, connues respectivement sous les noms de Groupe de Matagami et Groupe de Taïbi. Le Complexe intrusif de la Rivière Bell, qui occupe la base du Groupe de Watson, est un complexe lité consistant en une séquence stratifiée gabbroïque avec localement des niveaux stratiformes à concentrations d?oxydes magmatiques, la bordure de ce complexe est marquée par la présence d?un horizon granophyrique. Cette intrusion synvolcanique prétectonique, représente probablement la source de chaleur étant à l?origine de l?activité hydrothermale observée dans les roches volcaniques sus-jacentes. Suite à un levé aéroporté, le camp minier de Matagami a vu le jour en 1956 lors de la découverte du dépôt de Mattagami Lake, un gisement volcanogène de 25.6 millions de tonnes. Depuis ce temps, un total de neuf gisements ont été exploités et un dixième, Bell Allard, est présentement en production. En date du 31 décembre 1999, la production historique du camp s?élevait à plus de 41 millions de tonnes. Cette présentation mettra l?accent sur la géologie des récentes découvertes dans le prolifique camp minier de Matagami. Les ressources publiées pour le dépôt Persévérance sont de 947,000 tonnes titrant 19.12% Zn, 1.37% Cu, 32 g/t Ag et 0.40 g/t Au. Deux autres découvertes, Équinoxe et Persévérance Ouest contibueront à la ressource globale. Les trois dépôts sont situés au niveau de la Tuffite Clef même si les roches sus-jacentes ne sont pas celles typiquement observées dans les autres dépôts du flanc sud. Ces découvertes sont le résultat d?un programme d?exploration ciblé et soutenu, démontrant ainsi la possibilité de découvrir de nouvelles ressources même dans les camps miniers comme Matagami qui ont été explorés intensivement depuis plus d?un demi-siècle.

May 1, 2001

By X. J. Guo, H. X. Li

The biological heap leaching at Zijin copper mine is currently the largest industrial application of biohydrometallurgy and one of the earliest mines to develop biological metallurgy technology in China. Since 2001, through demonstration plant and different expansion stages, it has been developed to produce 20,000 tons cathode copper annually. However the ore grade of heap leaching gradually decline year by year with copper grade average at around 0.23% now. The copper mineral is mainly the secondary copper sulfide, and symbiosis with higher content pyrite, the sulfur and iron contents is about 15 times as copper in the ore (S/Cu>15), so the acid and iron treatment of leachate, extractant and acid mine waste water is a great challenge. Combined with located in the rainy area of southern China, huge amounts of over 10 million cubic meters acid drainage need to be treated every year, so the recovery of copper from waste water as well as low grade ore is one of the characteristics of this process. This paper in general introduced the operation of heap leaching, solvent extraction, stripping and electrowinning process in Zijin mine, summarized the experience of production and technical practice, and discussed the methods of heap construction, leaching rate enhancement, third phase formation and treatment, mine effluent treatment, resource recovery and heap slope reclamation. INTRODUCTION The Zijinshan gold and copper mine is located in southeast China, Fujian province, and the typical distribution characteristics of gold and copper deposit are "upper gold and lower copper", both are large porphyry deposits. By the end of 2017, the accumulated proven reserves of available gold resources were 318 tons, copper are 2.15 million tons, and the prospective reserves of copper are more than 5 million tons. The gold mining is open pit while the copper mining is open pit and underground. The cut-off grade of gold mining is 0.15 g/t, and that of copper mining is 0.15%. A large number of very low-grade gold ores (grade <0.30 g/t) adopt a combined ore-dressing process of “partial crushing/ore washing/reprocessing/heap leaching (overlying)/ carbon slurry" independently developed, while flotation and bio-heap leaching are adopted for copper mine. Among them, copper ore with more than 0.25% copper content enters the flotation system to produce copper concentrate, while that of less than 0.25% copper content is processed by bio-heap leaching, solvent extraction and electrowinning. Zijin biological heap leaching plant is the first mine in China to achieve the scale of annual output of ten thousand tons of cathode copper since 2006. In 2008, the solvent extraction and electrowinning system were expanded, now with a daily processing capacity of 20,000 tons of ores, an annual output of 20,000 tons of cathode copper, the expanded plant is the largest biohydrometallurgy plant in China.

Jan 1, 2019