Search Documents

By B. R. List, E. R. F. Lord

The Syncrude open pit mine, located near Fort McMurray in northeastern Alberta, produces approximately 410 000 tonnes of oil sand feed daily, which, after undergoing a bitumen extraction phase, generates approximately 315000 tonnes of tailings solids daily. The tailings are used to hydraulically construct containment dykes and supporting beaches of the storage facilities. Tailings deposition commenced in May 1978 with the commissioning of the Mildred Lake Settling Basin which is currently composed of approximately 600M m3of solid sand approximately 300M m3of contained fluids with fine tailings in suspension for consolidation. Two other storage facilities, commissioned over the past six years, have been developed to store sand and consolidated fine tailings referred to as mature fine tailings. Fine tailings reduction initiatives being developed will be successful in reducing future production of fine tailings volume by 20%. These initiatives include spiking (addition of fine tailings to coarse tailings lines for deposition), composite tailings (addition of gypsum to promote consolidation) and freeze/thaw dewatering, also to promote consolidation. The mandate of research efforts is to enhance tailings disposal and to develop economical and technically feasible reclamation initiatives. Final tailings landscapes will be geotechnically stable and ecologically productive to minimize or eliminate long-term liability. This technical paper will review the design philosophies of the current facilities and provide an overview of the areas of continuous improvement in the field of tailings management practices through the concerted research efforts and their implementation.

Jan 1, 1997

By C. W. Jr. Waterman

INTRODUCTION MY SUBJECT is one which would require several speakers and many hours of time for adequate presentation in all its many facets. Because of the widely varying market requirements and coal seams mined, the coal industry of the United States bas of necessity employed many types of preparation facilities to satisfy its needs. Predominance of Baum-type jigs, however, bas marked the mechanical cleaning installations since the early thirties, and these machines continue to hold the lead. CLEANING As a matter of record we find that, at the end of 1948, we had 480 mechanical cleaning plants in operation. Of these, 19 used air cleaners only,?400 used water washers only, . and 61 used dry and wet washers in combination . Due to the increased use of spray water underground on cutting and mechanical mining equipment, there has in recent years been a marked downward trend in dry cleaning installations. In fact, the moisture in dry-cleaned fines has been increased to such an extent by spraying that recent dry cleaning installations have incorporated thermal drying ahead of the dry cleaning units in an effort to overcome the varying and increasingly higher moisture percentages in their raw coal feeds. While on the subject of dry cleaning, it might be well to bring to your attention one of our most recent developments in this art. I refer to the McNally-Brusset vacuum jig.

Jan 1, 1951

By Sandra L. Mesa-Espitia, Gretchen T. Lapidus

Gold present in arsenopyrite matrices is refractory and requires highly oxidative pretreatments in order to obtain acceptable degrees of extraction. However, these release many byproducts that are harmful to the environment. In the present work, a high-grade arsenopyritic ore was pretreated with different solutions, containing hydroxide ion, EDTA, oxalic, tartaric, or citric acids, to improve gold extractions in a posterior leaching step. The pretreatments were carried out at room temperature for 24 hours with a respective ligand concentration of 0.25 M. Once completed, the residue was leached in a thiosulfate solution to quantify the effect of the pretreatment on gold extraction. Only 29% of the gold content was leached, with very slow kinetics, in the untreated mineral. However, after pretreatment with tartaric or citric acid, the kinetics improved, although the percentage of gold extraction only reached 42-45%. The highest gold recovery, with very rapid kinetics, was found with the oxalic acid or the hydroxyl ion pretreatment (70 and 62%), respectively, but also corresponded to the most arsenic co-dissolution.

Jan 1, 2014

"5.1. IntroductionThe sample preparation requirements for bulk analyses of platinum-group elements (PGE) are different from the requirements for ore microscopy and in-situ analyses. It is necessary that the initial sample collection results in as representative a sample as possible for both types of analyses. Ingamells (1980) believes, however, that sampling is always imperfect and that there is no such thing as a truly representative sample. Once collected, the usual low content and irregularly dispersed nature of the PGE require that samples for bulk analyses be made as uniform as possible, whereas in samples for ore microscopy and in-situ analyses the PGE must be concentrated. Because of the generally high specific gravity of platinum-group minerals (PGM), certain precautions must be taken, such as mixing the sample material in the bags prior to opening.5.2. Preparation forBulk Analytical MethodsThe principal factors that determine the size of the sample required for a bulk analysis are grade, heterogeneity and grainsize. Initially, the grade and sample heterogeneity can only be estimated and a sampling methodology is developed with experience. It is essential at all times, however, that the assayers have information about the source of the sample and the purpose for the analysis. Information on the grain-size, which can only be obtained through mineralogical analysis, is also very important for PGE analyses, but, unfortunately, is often ignored.5.2.1. Samples fromUnconsolidated DepositsConcentrations of PGE may occur in eluvial deposits as well as in a large variety of alluvial deposits, including those of fluvial and glaciofluvial origin. These deposits are often difficult to map and sampling is further complicated by the wide range, from sand-size to boulders, of the non-POE-bearing constituents, and by the irregular distribution and shape of the ""pay streaks"". PGE concentrations in unconsolidated deposits are largely composed of resistant Pt-Fe and Os-Ir-Ru alloys (cf. Cabri and Harris, 1975 and Raicevic and Cabri, 1976), thus making comminution to the usual-150 to -200 mesh somewhat unreliable, due to the malleability of these alloys."

Jan 1, 1979

By J. A. Vonhof, R. O. van Everdingen

Since 1949, a total of 59 disposal wells have been installed in Canada to inject liquid wastes from refineries, mining operations and chemical plants into subsurface formations at an ever-increasing rate. Well depths range from around 600 feet to almost 5,500 feet; injection rates range from 0.5 (U.S.) gpm to more than 1,000 gpm for individual wells; wellhead injection pressures range from a slight vacuum to over 500 psi. Apart from strictly technical considerations of well design, the geological, hydrodynamic and hydrochemical conditions at the disposal site have a strong bearing on the safety and success of such operations. Prevailing hydrogeological conditions in large portions of the country do not allow safe subsurface disposal.

Jan 1, 1973

By D. Pérez Escobar

Multiphase steels are quite sensitive to hydrogen embrittlement. Laboratory tests to evaluate this often use electrochemical, charging to introduce hydrogen into the sample, but damage purely caused by hydrogen charging has to be avoided. A ferrite-bainite steel, was charged using various conditions to identify when surface blisters occurred. Samples were also checked for internal, damage by electron microscopy. This study was repeated for three other multiphase steels and pure iron. An HSLA steel, was found to be more resistant whereas pure iron was quite susceptible to internal, hydrogen damage. For al, industrial, steels, cracks concentrated in the middle of the sample were attributed to inclusions and segregations, inherent to production.

Jan 1, 2010

By Ralph J. Holmes, David McCallum, Alan Roberts, Rolando Orense, University of Auckland, Tobias Krull, Tom Honeyands, Kenneth Williams

"The safe ocean transport of bulk commodities like iron ore, coal, nickel ore, manganese ore and bauxite by large bulk ships is vitally dependent on the stability of the cargo under the influence of wave induced ship motion. Safety standards are set by such bodies as the International Maritime Organisation (IMO) with recommended tests for the assessment of bulk commodities. Since the 1960s, the bulk cargo code (BC Code) commenced defining methods to determine the Transportable Moisture Limit (TML) for transportation of bulk commodities. By the latter part of the 1960s, three TML test methods were defined, namely the Flow Table, Proctor-Fagerberg and Penetration tests. All three tests were predominantly aimed at determining TML values for mineral concentrates.More recently, bulk commodity producers, Maritime Organisations and Port Authorities worldwide have been investigating whether commodity based TML methods better reflect realistic safe ship transportation than the current concentrate based TML test methods. In these investigations, the relationship between the mineralogical and particulate parameters of specific commodities with respect to cargo stability and moisture retention has provided insights into the development of tailored TML test methods. To this end, an AMIRA International project (P1097) undertaken by CSIRO, TUNRA Bulk Solids, the University of Newcastle and the University of Auckland assisted the IMO Technical Working group to investigate the relationship between iron ore fines characteristics and a new TML test specific for iron ore fines bulk cargoes.A review of the three standard concentrate based TML methods and characterisation studies of iron ore fines, as well as cyclic triaxial testing to determine liquefaction resistance, resulted in the development of a modified Proctor-Fagerberg method for determining the TML of iron ore fines. Of particular importance in determining TML is mineral composition, porosity, particle density and allowing time for moisture equilibration."

Jan 1, 2016

By Matthew A. Baumann

Tooth wear on mining shovels presents a challenge for productivity. A shovel with worn teeth suffers from increased digging forces, longer fill times, and an increased likelihood of lost or broken teeth and adapters. Efficient maintenance planning relies on knowledge of tooth decay rates and patterns. A fully automated wear monitoring system can record detailed logs of tooth wear, permitting G.E.T. personnel to optimize maintenance scheduling. Studies have demonstrated that planned tooth change-outs result in significantly reduced costs as compared to unplanned maintenance. A machine-vision-based tooth-wear monitoring method is introduced. A rugged camera is installed on the boom of cable shovels, or on the stick of hydraulic shovels. The images are processed using a photogrammetric algorithm to determine the individual tooth lengths. Tooth length data is collected at intervals during shovel operations, forming a profile of the current wear state, speed of decay, wear pattern, and expected lifespan of teeth. A case study in a South American mine on a Komatsu PC8000 hydraulic front shovel is presented. Tooth wear is tracked over a 6-day period and wear rate statistics are computed for 6 teeth. This validates the system and provides an example of how wear patterns can be recorded and analysed by an automatic system. Armed with this data, mine personnel can reduce the cost and lost time due to unplanned maintenance, and observe the effects of mine conditions and operator behaviour on tooth wear.

May 1, 2011

By I. S. Thompson

A program of geochemical till prospecting, carried out by Derry, Michener & Booth in 1974, was instrumental in t~ e discovery of a copper deposit in Currie Township, Ontario, beneath thick lacustrine deposits of the Abitibi Clay Belt. The prospecting system involved the continuous collection of glacial sands and gravels beneath the clays, using a track-mounted, dual-tube rotary drill, and the separation and geochemical analysis of the heavy mineral content for Cu, Zn, Pb, Ag and Au. In one of 22 holes drilled down-ice from nine Canadian Nickel airborne EM conductors, fragments of chalcopyrite-bearing graphitic argillite, assaying 12% Cu, were recovered from a 14-foot gravel section beneath 83 feet of clay. Ultimately, mineralization was identified in 10 of 11 additional holes drilled up to 3,000 feet down-ice from the Currie deposit. The glacial fan, when compared to the 1,200- by 165-ft area of the subcropping mineralization, is at least 20 times the area of the deposit and is the result of glacio-fluvial reworking of the mineralized ground moraine. The Currie deposit is contained within a Keewatin succession of graphitic argillite, dacite tuff and graywacke, which is intruded by dacite and feldspar porphyry sills and dykes and truncated by a Keweenawan diabase dyke. Grade and thickness of the mineralization, which lies chiefly within the argillite, is related to felsic intrusives and hydrothermal alteration, and to fold hinges.

Jan 1, 1979

By H. W. King

"Cryogenic engineering is concerned with components and machines which operate for long periods of time at temperatures within a few degrees of absolute zero. The absence of a ductile-brittle transition is thus the prime component of the specification for a suitable low-temperature alloy. The word "" cryo"" means ""frost-forming"" , and this leads to the second component of the alloy specification, which is resistance to corrosion in humid atmospheres. Further, although most early applications of low-temperature alloys were limited to the storage or transportation of liquified gases, an increasing proportion of alternative energy storage and conversion technologies are being based on the availability of high-field superconducting solenoids. The third basic component of the specification for a low-temperature alloy is thus the absence of a low-temperature ferromagnetic transition.Although the firs t two of these components of the specification can be met by using austenitic stainless steels, many of these supposedly "" non-magnetic"" alloys have been found to undergo martensitic transformations to ferromagnetic phases at very low temperatures. In addition, steels which remain structurally stable may still exhibit other magnetic transitions, e.g. to antiferromagnetic or superparamagnetic states. The successful application of these alloys in cryogenic engineering has thus required an initial basic study of the types of magnetic transition that can occur in such concentrated solid solutions, followed by a more applied study directed at an alloy formulation which will induce beneficial magnetic states at low temperatures."

Jan 1, 1981

By Stuart McTavish

"The Brunswick Mining concentrator processes 10,000 D.S. T. per day of a complex sulphide ore. Four separate concentrates- zinc, lead, copper and bulk-are produced by selective flotation. Several major changes have been made to the Brunswick flotation circuit to improve the process and control. This paper will describe the present flotation practices at the Brunswick Concentrator. Special emphasis is given to the conversion of two of the primary circuits to an SO2-aeration flowsheet, and to the addition of a new secondary zinc flotation circuit that produces a zinc concentrate from the plant tailings. IntroductionBrunswick Mining and Smelting Corporation operates a zinclead- copper and silver mine and concentrator near Bathurst, New Brunswick. Since the start-up of operations in 1964, the flotation flowsheet has undergone major modifications to process the increased tonnages and to produce a greater number of concentrates. The flowsheet for the concentrator as it was in 1971 has been described by Neumann and Schnarru) and by Ersklneco. Since then, in 1971, the No.6 concentrator was converted from bulk flotation to selective flotation to produce a copper, lead and zinc concentrate. A separate zinc upgrading circuit was installed in 1972 and a bulk flotation or dezincing circuit, which reduced the zinc in the lead concentrate, was started in 1973. In 1976, the secondary zinc circuit was initiated.In addition to these new circuits, changes have been made to the existing circuits to simplify their operation."

Jan 1, 1980

By Robert B. Parsons

"It is quite likely that more than a handful of junior exploration companies will receive some startling news from their accountants this spring when 1989s tax returns are being prepared. These companies could find that, for the first time ever, they will have to write a cheque to the federal government on account of a new federal capital tax which became effective July I, 1989IntroductionMany mining companies which have never had to pay a federal income tax are finding that they indeed have a tax liability for 1989. Non-producing companies, such as junior exploration companies, almost automatically assume that they don't have to pay any income tax. But, a new tax imposed under the Income Tax Act catches especially the company that has no income.Effective July 1, 1989, a federal capital tax (some call it a corporation minimum tax) is payable by any corporate carrying on business in Canada where the corporation has ""taxable capital"" exceeding $10 million. As a result of the popular use of flow-through shares in recent years, many junior exploration companies are finding that their balance sheets show capital stock over $10 million, and that they are consequently caught by the new tax. Further, some of these companies are finding, to their chagrin, that the tax for 1989 was due on February 28, 1990, and that non-deductible interest is ticking away on unpaid taxes."

Jan 1, 1990

By W. L. Strand, D. N. Madge

"Experimental and pilot operations in bituminous sand processing require due care and attention in the design and analysis of measurement programs. This paper deals with a case study in experimental design and data analysis for a series of experimental campaigns that have been conducted over the past five years by Kilborn Western Inc., acting on behalf of Bitmin Resources. Beginning with the design of the experiment and following into the use of linear and nonlinear regression models, the phenomenology of bitumen extraction is illustrated. The final testing program tested 13 oil sand types as well as a wide range of process variables for all the unit operations of the complete process.The program was successful in developing process fundamentals and scale-up criteria. Several phenomenological models were proposed and tested. Their range of applicability was explored. This paper illustrates the range of applicability of these models and discusses the development of alternative models.IntroductionOver the past five years Kilborn has conducted a series of bench scale and pilot scale experiments designed to explore the phenomenolgy of a new concept in medium temperature processing of bituminous ores. These experiments at feed rates ranging from .1 to 24 t/h were conducted on water wet sands from the .Athabasca region near Fort McMurray. They were based on experimental designs chosen to provide a systematic means of identifying the response surfaces of the process over a range of conceptual designs. The following diagram shows the experimental arrangement:"

Jan 1, 1998

By R. C. Bryce, G. S. Martin

"Aur Resources Inc. is the operator of the Louvicourt Mine located 40 km east of Val d'Or. Quebec. Les Entreprises Minieres Redpath Limitée a member of the 1.S. Redpath Group of companies was contracted to construct two vertical mine shaft collars in deep overburden.During the spring of1991 two vertical shaft collars were established in wet, running sand that was in excess of20 m deep. This paper will illustrate the engineering and construction techniques used in establishing these collars and the methods used to overcome the various obstacles that occurred during construction.IntroductionThe Louvicourt copper/zinc/gold/silver deposit is located 40 km east of Val d'Or, Quebec, is adjacent to the former Louvern Mine which operated at depths of 40 m to 850 m below surface (Fig. 1). This deposit was discovered in mid-1989 as the result of systematic exploration and diamond drilling based on a geological model. The Louvicourt project is operated by Aur Resources Inc.The property is being developed to produce 4000 tid with an anticipated life of just over 17 years. Mill start up is scheduled for July 1. 1994, commercial production October I, 1994, and full production by late 1995. The current production plan provides for 24 040 (XX) t averaging 3.89% copper, 1.95070 zinc, 0.039 oz gold per tonne and 0.99 oz silver per tonne, to be mined."

Jan 1, 1994

By T Nakamura, M. Itoh

Most of the used cathode ray tube (CRT) glass in Japan, which contains lead oxide, was exported and recycled in overseas factories of new CRTs. However, domestic treatment and recycling of waste CRT glass has become necessary because overseas CRT factories have shut down and exports of CRT glass have stopped. Some of the waste CRT glass recycled domestically is charged in lead blast furnaces instead of silica flux, because there is no local reproduction route for glass that contains lead. However, the mass of CRT glass that can be treated in this manner is limited because of its high silica content. Consequently, additional treatment methods for waste CRT glass are required so that more can be used as a lead smelting material. In this study, waste CRT glass was treated with hydrofluoric acid to dissolve the silica contained in the glass, and the dissolved lead was recovered by precipitation. Lead metal was recovered by electrodeposition from the prepared hexafluorosilicic acid solution.

Jan 1, 2011

Resistance spot welding is the most common type of welding in the automotive industry. In RSW the size and shape of welding nugget is one of the most effective factors on mechanical properties, such as tensile shear strength and fatigue strength. so properly adjusting the variables of the welding is necessary .in this study the effect of different parameters of RSW including time, current, electrode force, geometry of electrode so diameter and angle of electrode tip in the shape and size of welding nugget evaluated. for experimental procedure, low carbon steel sheet st12 is used. the process is simulated with finite element method by using ANSYS software. for the formation of welding nugget a 2 dimensional symmetrical model electrical-thermalmechanical is used and for elevate the accuracy ,we determined the properties of material related to temperature. The results show that increasing the time and current of welding, the diameter of spot weld also increased and the role of current is more impressive. and also increasing the electrode force decrease the diameter of the nugget due to increasing the contact area and decreasing the resistance .increasing the diameter of electrode tip cause increasing contact area and decreasing the resistance and decreasing the diameter of the nugget. furthermore, changing tip angle and electrode diameter don't show sensible change in the geometry of the welding nugget. comparison between simulation and experimental result show a good adaption.

Oct 1, 2011

By P. Molera

"In Catalonia, between the 10th century and 1878, some installations were developed which at first were called ""factories"" and later ""fargas"", since they manufactured iron and steel of low carbon content. Because of its excellent quality, the fame of this metal spread from Catalonia to many countries. Fargas were started in Corsica, the Low Countries, Germany, Oriental India, Madagascar, Finland and along the rivers Orinoco and Mississippi among others. The extractive process used in these fargas has passed into history as the ""Catalan Farga Process"", ""Catalan Process"", or just ""Farga Catalana"". With this technology, raw material was obtained for the fabrication of tools, nails, weapons, grilles, etc. to supply the national and export markets. Aside from meteorites and native iron, found as metallic nodules in basalts in Greenland and Palestine, the ancient civilizations, which had no means to reach the fusion temperature of iron (1535°C), obtained iron by a direct process. Similar processes were used until quite recently (1930s) by certain tribes in Central Africa; holes in the ground were filled with iron ore and coal, and combustion encouraged by blowing air by mouth or with bellows made of animal skins. Thus without melting the iron it is possible to reduce the mineral and obtain a porous and impure metallic mass, which is purified on forging by mechanical squeezing. With a process very likely similar, the famous column at Dehli weighing 6.4 m.t. was built about 300 B.C."

Jan 1, 1999

By William C. Browning

An economic drilling programme is one which costs the !east in chemicals, equipment, and time. The basis for such a programme with rotary drilling techniques is a drilling fluid in which bentonites do not swell. This is recognized in the growing trend toward gyp and other inhibited mud systems. Therefore, even though the mechanism of thinner action is a subject of applied colloid ,chemistry, the understanding of this mechanism is of economic importance in controlling the flow properties of inhibited muds. In phosphate, or sodium tannate, conditioned muds that are relative-!y free of contaminating-electrolytes, the thinner, or dispersing agent, is adsor.bed, ?creating an electrical double layer about the clay particles. The mutual repulsion of these charged particles effects colloidal stabilization, or deflocculation of the suspended clays, as discussed by Norton and others. In inhibited muds, however, the electrolyte concentration in the filtrate is sufficient to collapse the double layer and flocculation of the mud solids occurs, as evidenced by increased viscosity and gel values. Chemicals to control the flow properties of inhibited muds, therefore, are vital to the successful use of these systems as it is not always economical to adjust flow properties by watering back. Flocculation of suspended particles, as indicated in the work of Vervey, Overbeek, and others, is due primarily to gravity-like, long-range Van der Waals forces. Prevention of flocculation may, therefore, be secured by the interposition of any barrier between the particles, the thickness of which approximates the extension of the Van der Waals at-traction. Organic polyelectrolytes, such as Kembreak, Rayf!o, and Q-Broxin, may act to increase the double layer charge when used in small amounts in fresh-water muds. More important, however, is the fact that in inhibited muds an increase in concentration of the polyelecholyte permits the formation of a condensed film adsorption layer of the polyelectrolyte about the clay particle. When this occurs, the extremely viscous condensed adsorption layer creates a mechanical. barrier that prevents flocculation of clays, even in the presence of inhibiting concentrations of elecholytes. Rheological evaluation of the degree of deflocculation, or colloidal stability, may be made by utilizing the known effects of particle inter-action and volume concentration on the flow properties of suspensions. Rheological evaluation should be supplemented by direct microscopic or ultra-microscopic observation.

Jan 1, 1958

By Robert D. Brown

"Important tax changes, many of them of direct interest to the mining industry, were contained in the budgets brought down by federal and provincial finance ministers across Canada this spring. This month, Tax Notes presents a brief summary of important tax changes introduced at the federal and provincial levels in the last few months.IntroductionIn the March 1980 issue of the CIM Bulletin, Tax Notes surmised that the short-lived 1979 budget proposals of the former Conservative government offered a unique glimpse of budgetary changes that might be unfolded in 1980. Scene II of this ""now you see it-now you don't"" drama opened on April 21, 1980, when Finance Minister Allen MacEachen, in an ""economic statement""' reintroduced a selection of tax proposals taken from the ill-fated Conservative' budget of December 11, 1979, but refused to bring forward major new proposals in tax and finance.Mr. MacEachen proposed a 5% surtax on federal corporation income tax to apply in the 2 years from January 1, 1980 to December 31, 1981, as a slightly modified version of the same surtax proposed by former Finance Minister Crosbie in his December budget address. Mr. MacEachen also reintroduced a number of technical amendments which would affect the taxation of mining income in certain instances. In addition, a large number of other tax proposals suggested in the previous Conservative budget were also reintroduced, although there are some notable omissions."

Jan 1, 1980

By K. John

"THE most recent estimate of minteable coal reserves in Saskatchewan was made by the Federal Royal Commission on Coal (1944- 6). Saskatchewan was then estimated to have some 24 per cent of the Canadian reserves and two-thirds of this is located in what is called the Souris-Estevan area, which lies in the southeast corner of the Province and border's on the International boundary. It is also estimated that there are some 61/2 million thousand-tons in this area of lignite coal which grades 8,000 B.t.u. or less and has a moisture content ranging from 30 to 33 per cent. Ownership of coal rights in the Province is widely dispersed between the Crown, individuals, and corporations, and a recent survey disclosed that 40 percent of ownership was vested in the Crown and 60 per cent in private individuals and corporations. Coal rights on Crown lands may be leased at an annual rental of $ 1.00 an acre. Under such leases, a royalty of 5 cents a ton is levied on all coal mined. A royalty of 7 cents a ton is levied on coal produced from lands where mineral rights were purchased from the Federal Government prior to the transfer of jurisdiction over natural resources to the Province, in 1931. An annual mineral tax of 50 cents per acre has also been imposed by the Provincial Government on all coals within a defined producing areas."

Jan 1, 1952