Search Documents

By Helmut Lerchs

An open-pit mining operation can be viewed as a process by which the open surface of a mine is continuously deformed. The planning of a mining program involves the design of the final shape of this open surface. The approach developed in this paper is based on the following assumptions: 1. the type of material its mine value and its extraction cost is given for each point; 2. restrictions on the geometry of the pit are specified (surface boundaries and maximum allowable wall slopes); 3. The objective is to maximize total profit-total mine value of material extracted minus total extraction cost. Two numeric methods are proposed: A simple dynamic programming algorithm for the two-dimensional pit (or a single vertical section of a mine), and. a more elaborate graph algorithm for the general three-dimensional pit. ASURFACE mining program is a complex operation that may extend over many years, and Involve huge capital expenditures and risk. Before undertaking such an operation, it must be known what ore there is to be mined

Jan 1, 1965

By Alfredo Bambaren

First Encounters between Communities and Mining 1. Importance, meaning and process 2. Antamina?s study case 3. ?Self-organization? theory (NLP) 4. The story we tell, the values we live 1. Importance, Meaning and Process ? First encounter stays in mind as a model. ? First encounter means foundation. ? First encounter builds the story.

May 1, 2010

By R. J. Brailey

"A USER'S VIEW OF CONVEYOR WEIGH SCALESThe Sudbury Operations of Falconbridge Nickel Mines Limited includes seven mines, three concentrators and a smelter. The flow of ore, concentrates, fuel and fluxes between and within these plants requires measurement for accounting and control. The design, installation and maintenance .of weighing systems falls within the responsibility of the Instrumentation Department of Falconbridge Nickel Mines thus al lowing a common approach to conveyor weighing problems and the benefit of a common spares supply. This paper gives a brief overview of the recent experience with conveyor scales within the Sudbury Operations and discusses the problem areas.GeneralThe best way to establish the total amount of material going to or from a process is with a bucket and a stop watch. Unfortunately the flowrates involved in mining plants make the buckets very large, but wherever it is feasible static weighing is the preferred method of determining total quantity. This applies particularly to batch systems, where the material can be brought to rest long enough to allow a very accurate weight determination. Any form of weighing in motion is susceptible to variations in the forces of the transporting system. A belt scale is affected by its position on the belt, idler alignment, support stiffness, variations in belt tension, material spills and build-up, and a host of other factors all of which require careful consideration in any installation.As with instrumentation applied to any system the plant should be designed to ensure that the best results can be obtained from the equipment. This means getting the scale supplier together with the conveyor supplier as early as possible in the designing of a new plant. Any corners cut in scale installation will be paid for later in poor results and/or increased maintenance."

Jan 1, 1975

By L. A. Nazarova, M. Vandamme, L. A. Nazarov, R. I. Rodin

"The paper describes a new method of interpreting the “canister test” data for the quantitative estimation of gas-kinetic parameters of coal bed based on the developed model of gas emission from coal sample placed in a sealed container. The model accounts for grain-size composition of the sample, initial gas content S, as well as coefficients of diffusion D and mass transfer ?. The inverse coefficient problem is formulated to find S, D and ??from the data of pressure measurements in the sealed container. It is shown that the inverse problem is uniquely solvable if the pressure is dropped during the experiment. The method has been tested using the data from an underground coal mine in the Kuznetsk Basin.Based on the poroelastic model of a coal bed and Khristianovich’s concept about origination and evolution of the filtration zone F in the neighborhood of a degassing borehole the authors considered the corresponding direct problem on rock mass geomechanical state. It was offered interpretation method for data on pressure measurements in a plugged degassing borehole allows evaluation of the diffusion coefficient, the horizontal component of natural stress field and parameters of F. The related inverse problem of the mixed type is formulated, and the cost function is constructed. The analysis using synthetic input data has shown that the cost function has a number of local minimums arranged on the same straight line, one of the minimums being the inverse problem solution. INTRODUCTIONPre-mine degassing is an integral part of coal mining. It allows mitigation of induced accidents in mines (coal and gas outbursts, rock bursts) (Guide, 1990; Malyshev & Airuni, 1999; Seidle, 2011) and also furnishes an alternative and ecology-friendly energy source—methane (Rice, 1997; Nambo, 2001). Choosing an optimized pattern of degassing boreholes, as well as estimating degassing time and amount of gas recovered requires data on gas-kinetics indices of coal beds out of which the key parameter is a gas content S. According to the latest guidelines for coal mines in Russia (Ruban et al, 2012), mining is allowed if S in a coal bed section is under 7 kg/m3."

Jan 1, 2015

This paper examines the latest advances in mine hoist motor and drives systems. The technology employed for large hoists has migrated from the traditional DC technology to AC motors with cyclo convertor drives, and more recently, advances in pulse width modulation (PWM) drives have resulted in these being applied to large hoist drives. When combined with PWM drive technology, the induction motor presents the ideal solution for hoist applications This paper examines the factors in choosing a suitable PWM drive and motor for a hoist installation. Factors under consideration include: ? hoist duty cycle, ? drive rating restrictions, ? choice of power semiconductor device,, ? low speed operation, ? maintenance ? reliability The cage induction motor and synchronous motor are compared and it is shown that the induction motor is the motor of choice for large hoists.

May 1, 2010

By M. Potesser

In the past, different furnace types have been developed for use within the copper industry, with two common anode furnace designs typically used in copper smelting plants worldwide: the tiltable reverberatory furnace (KPO) generally used for the secondary copper industry and the cylindrical or drum type anode furnace (TRO) for handling a liquid blister charge generated in primary copper production. The disadvantage of the KPO is its design related to the longer refining period, because of the low bath depth, however it provides good conditions in the melting period due to its large bath surface. On the other hand, small amounts of scrap charged into the TRO increase the melting and dissolution period, but it provides good conditions for the refining period. The newly-developed elliptical furnace concept (TRE) offers the advantages of each of these furnace types. The special design allows melting of the scrap more efficiently than in the KPO and refining the liquid copper more efficiently than the TRO. This paper shows a metallurgical comparison of the three furnace types in regard to the melting period by heat technological considerations (optimized arch design) and of the refining period done by CFD with concentration on current, recirculation and dwell time of the gas in the melt. The paper outlines the possibilities for a reduction of the tap-to-tap time and energy consumption as well as for an increase of the production capacity, which can be achieved by applying the TRE instead of the conventional furnace designs.

Jan 1, 2007

By Marc C. Bétournay

"Surface crown pillars, acting to safely protect underground workers and operations from surface elements, are recognized, herein, as distinct from conventional deeper underground pillars. Moreover, because of the variation in mining and geological conditions that exist from mine site to mine site, each case is viewed as unique. A review of numerous case studies and existing literature indicates that there is little general information or systematic problem-solving approach associated with them.A design process, not unlike that of other engineering disciplines, is presented to correct these deficiencies. As part of its purpose, it will inform operators of the key elements required for design and will address the problems of these appendages. The design, while taking into consideration possible surface crown pillar settings and inherent characteristics, is founded on a step-by-step procedure starting with site investigations through to monitoring or pillar recovery. The process is flexible, in that it incorporates decision making and changes in mining strategy. The purpose of each step is explained and each step is extensively described in terms of the required equipment and methods for field work, analysis and support measures. Analytical formulae and studies from several fields directly applicable to surface crown pillars are also given. Recommendations for future research studies are presented."

Jan 1, 1987

By N. Saracoglu, J. P. Golightly, R. H. Wallis, J. J. Brummer

"In January 1974, the Minerals Division of Canadian Occidental Petroleum Ltd. made the strategic decision to add uranium to its active exploration commodities and through compilation studies selected northern Saskatchewan as the most attractive and cost-effective exploration area in Canada. In August 1974, 100 sq. miles were staked adjacent to Gulf Minerals' Rabbit Lake deposit and east of the Esso Minerals Midwest boulder train. Initial exploration was based on geologic models of the Rabbit Lake deposit.In the summer of 1975, surface surveys delineated radon anomalies which were drilled that winter and found to overlie anomalous concentrations of uranium in the regolith which forms the upper unit of the crystalline basement. Within the crystalline basement, one hole intersected graphite and pyrite with anomalous nickel-cobalt-arsenic. Geochemical and radiometric surveys followed in the summer of 1976. Drilling in the winter of 1977 intersected several zones of graphite and also anomalous, but uneconomic, uranium abundances. Also in 1977, Dahlkamp and Tan (1977) described the coincidence of graphite and uranium at Key Lake and ground EM surveys on CanadianOxy claims detected graphite conductors beneath 250 ft of Athabasca sandstone. Inco Limited joined the project in April 1977 as a 50% partner. The project area was then surveyed using the airborne INPUT EM method, which detected 84 miles of conductors, with associated graphitic metasediments. On the ground these were located with MaxMin surveys, and follow-up drilling located the ""Tent"" Lake uranium zone.In 1978, the Midwest and Dawn Lake discoveries were announced, 7 miles and 2 miles west of the Joint Venture (J.V.) claims; and, in part for this reason, the 1979 winter drilling was concentrated on the deeper west side of the property. Exploration hole 102-79 intersected altered and uraniferous rocks, but stepout holes were barren. Drill hole 153-79 tested an under-snow three-station radon anomaly east of hole 102-79 and intersected 33 feet of 7.51 % U3O8, confirming the disco very of the McClean North zone. The geophysical grid of the McClean North conductor system was extended and detailed a strong, continous conductor to the south, called McClean South. This was drilled in January 1980and hole 1004-80intersected 22 feet of 2.95% U3O8."

Jan 1, 1983

By Theo Mayer

Presentation Outline Define data visualization in the context of workflow Present other industries? application and demonstrated benefits Provide conceptual tools to help you address a visualization strategy Hold 10,000 foot view ? to touch on many issues

May 1, 2008

By L. A. Anestiev

A method based on use of calorimetric data for the determination of solidification kinetic parameters is proposed. The method incorporates recent theories of nucleation and growth and allows modeling heat fluxes observed in calorimetric experiment. Statistically optimal estimations of the kinetic parameters, which include the activation's energies of nucleation and growth, are derived from experimental data by means of nonlinear regression analysis. The method is applicable to pure substances and alloys. The evaluation of the kinetic parameters characterizing solidification of pure Al is used for clarifying and exemplifying the method.

Jan 1, 2004

By Charles S. Ney

"ZINC-LEAD REPLACEMENT deposits straddle the steep-sided valley of Kicking Horse River at a point three miles east of Field, B.c., in Yoho National Park. The Monarch orebodies extend into Mt. Stephen on the south side of the valley, and outcrop at two points, 1,000 and 1,200 feet above the valley floor. The Kicking Horse deposits are in Mt. Field, on the north side of the valley, and they outcrop 200 feet lower.The East Monarch outcrop is said to have been discovered in 1884 during construction of the Canadian Pacific Railway. The larger West Monarch outcrop, 700 feet west of the original discovery, was not reached till 1917 because of its nearly inaccessible location on the cliff face.The Kicking Horse mine was staked in 1906. Little development was done for several decades, and mining was not commenced till 1935.At the East Monarch, mining was commenced soon after location, and several thousand tons of ore were shipped prior to 1912. At this time a gravity concentrator was installed. This was operated till 1924, and a total of 42,000 tons of ore were mined, including about 10,000 tons from the West Monarch. The period from 1928 to 1935 featured flotation milling and the mining of 265,000 tons of ore, mostly from the West Monarch orebody. Intensive exploratory development was carried out in both Monarch and Kicking Horse from 1935 to 1946. Production from both mines in this period totalled 380,000 tons. From 1947 to the time of closure in 1952, considerable new ore was found in both mines and 185,000 tons were milled. Immediate possibilities for finding ore in the Monarch were considered exhausted. Kicking Horse orebodies are known to persist with a low grade of zinc. Total production from the two mines amounts to 842,500 tons grading approximately 7 per cent lead, 10 per cent zinc, and 1.2 ounces per ton silver."

Jan 1, 1949

By P. M. Huck, R. John

"The National Uranium Tailings Program was established in 1982 to develop, in part, a mathematical predictive model which would allow the assessment of the impact of uranium mill tailings on the environment and particularly on humans. . To achieve this , various studies were undertaken to establish the role played by key constituents of the tailings. This paper summarizes the findings of a study carried out under that program, to examine the leachability of barium-radium sulphate sludges produced in the treatment of uranium mill tailings decants. The investigators performed detailed chemical an alysis of the sludge, applied geochemical computer models to investigate sludge leaching behaviour, and conducted experiments to assess the impact of bacteria on leaching. The modelling showed that the redox state o f the sludge-leachant system was the most important factor. Substantial bacterially-mediated dissolutio n of the sludge and release of radium was demonstrated experimentally under suitable reducing conditions . INTRODUCTIONIn September 1981, Phillip A. Lapp presented the final report of the National Technical Planning Group on uranium tailings research to the federal government (Lapp, 1981). Lapp' s group had performed an in-depth survey of the status of uranium tailings research in Canada and, as a result, recommended that a national program be funded in the amount of $18 .6 million. Half of this fund ing was to come from the federal government, with the two producing provinces , Ontario and Saskatchewan, providing the balance. However , the provinces declined to support the program and the federal government decided to inaugurate a reduced program with $8.5 million o f funds .In late 1982, the formation of the National Uranium Tailings Program (NUTP) was announced by the minister of state for mines. A primary objective of this program was to develop a mathematical predictive model that would permit the assessment of the impact of uranium mill tailings on the environment, a nd particularly on humans. The program was to use existing information to the greatest possible extent, and then fund research to fill in gaps or substantiate data where necessary .The NUTP was established to administer this program of contract research over a five-year sunset life. By the end of the 1986-87 fiscal year the NUTP had completed about 100 contracts. One of those projects was to study the effect of placing barium-radium sludge ba ck within the tailings matrix. Th is paper gives the results of that study."

Jan 1, 1989

By Arnfinn F. Prugger, Fritz F. Prugger

"The Saskatchewan potash beds are overlain by a number of water-bearing formations. There are water zones in the footwall as well. These aquifers created difficulties during the construction of shafts to the potash beds at 1()(}() m depth, and they pose a continuous threat to the safe and efficient operation of potash mines in the province.The first shafts to be sunk in Saskatchewan encountered major problems during shaft sinking. Of the 17 potash shafts started in the province, five had major water inflows during shaft sinking or after production startup, and one was abandoned because of water problems. The biggest obstacle encountered during shaft sinking was a poorly consolidated sand-shale-clay-siltstone unit commonly called the Blairmore Formation, which occurs at a depth of about 500 m. The initial problems with shaft sinking were overcome in the 19605by using European methods of freezing and the installation of cast-iron tubbings or a double-steel lining through water bearing horizons.From the start of production in the early 19605, operators have been aware of the ever-present hazard of potential water inflows into mine openings from permeable units in both the hanging wall (carbonates of the Dawson Bay Formation which occur 15 m to 50 m above the mining level) and the footwall (carbonates of the Winnipegosis Formation which occur 50 m to 150m below). This awareness has been reflected in conservative over-all extraction rates and mining layouts specific to local conditions. In spite of this consciousness, a number of water problems have occurred in operating mines. These have resulted in everything from simple increases in expenditure to the shut-down of one mine in 1987.In this paper a history of water problems in the Saskatchewan potash industry is given, followed by a summary of measures that are now commonly used to avoid these problems. A description of each inflow event is given, and the attempt is made to analyze the causes of each occurrence. Based on what was learned f rom each event, suggestions are made to prevent future water inflows into potash mines."

Jan 1, 1991

By I. Stefanou, J. Sulem

"In the last thirty years, the study of earthquake mechanisms has emphasized the major role of rock friction. Earthquakes appear to be the result of a frictional instability and occur by sudden slippage along a pre-existing fault or a plate interface. Multiphysics couplings play a major role in earthquake nucleation and seismic slip. The effect of shear heating and thermal pressurization may be of prime importance in the control of the stability of shear deformation inside the slipping zone. Other mechanisms in relation with thermal decomposition of minerals affect the pore pressure and the temperature evolution of the system, and can play a significant role in the extreme strain localization observed in field. The actual width of the localized zone is a key parameter for understanding fault weakening mechanisms. On the basis of field observations, laboratory experiments and recent advanced modeling, these phenomena are analyzed and discussed in order to bring some new insights in the understanding of earthquakes nucleation.INTRODUCTIONIn the last thirty years, the study of earthquake mechanisms has emphasized the major role of rock friction. Earthquakes appear to be the result of a frictional instability and occur by sudden slippage along a pre-existing fault or a plate interface (Scholz, 1998; Sykes, 1978). The conceptual model of spring slider system is commonly used to represent the interaction between an elastic crustal block and a fault zone. Stick-slip instability is possible if the softening rate of the shear resistance of the fault zone is high enough as compared to the stiffness of the crustal block. Therefore, weakening mechanisms that can explain how the frictional resistance of a fault decreases with slip and/or slip rate is of prime importance to understand how an earthquake nucleates. In recent years, several drilling programs in active faults (e.g. the Nojima fault in Japan, Boullier, 2011; the Aigion Fault in Greece, Cornet et al. 2004, the Chelungpu fault in Taiwan, Ma et al. 2006, and the San Andreas fault in the U.S.A. Ellsworth et al. 2000) as well as high velocity friction experiments (e.g. Tanikawa et al 2012a; Tanikawa et al. 2012b) have highlighted the physico-chemical processes involved in the nucleation of seismic slip (see for the example the review paper of Niemeijer et al. 2012)."

Jan 1, 2015

By M. C. Villeneuve, P. A. Siratovich

We present an integrated analysis of laboratory-based thermally induced fracturing and results of numerical models to give insight to the role of thermal shock fracture on geothermal reservoir rocks. Thermal stimulation is a reservoir permeability enhancement technique applied to commercial geothermal reservoir rocks to enhance fluid injection capabilities for spent power plant working fluids. The process is well known to enhance permeability but the thermodynamic and physical constraints of the process are less certain. In an attempt to constrain the interaction and the ideal conditions that lead to permeability enhancement, experimental procedures were carried out to mimic the conditions that a reservoir rock would experience during a thermal stimulation using temperature differentials ranging from 50-300°C. Samples underwent such thermal gradients under controlled laboratory conditions and were characterized for the changes to permeability, porosity, ultrasonic velocities, dynamic elastic moduli and petrological changes. The thermal stimulation was simulated in a FLAC2D thermal numerical model to investigate the nature of the thermally induced changes in the sample. The development of this model also allows us to investigate the relationship between geological characteristics and the ability to thermally stimulate any type of rock. The results indicate that numerical thermal shocking experiments are corroborated by laboratory-based results. The implication of this study is that the refined numerical models present an insight to the conditions and constraints under which thermal stimulation can prove to enhance permeability that could not be gained through purely laboratory-based studies.

Jan 1, 2015

By Bert S. Hall

"IntroductionThe purpose o f this paper is to review the evidence at hand concerning the earliest centuries of cast iron in Europe, from roughly 1400 A.D. until the second half of the sixteenth century. For the most part it is concerned with the relationship between two technologies which emerged first in China and then later appear in Western lands, gunpowder weapons and iron founding. We should not assume, as I hope to show later in this discussion, that weapons constituted the only product for which the iron founder had any market, but it is clearly true that attempts to produce weapons constituted the most severe technical challenge for the early founder. Firearms appear for the first time in Europe in the 1320s and develop into significant weapons on the field of battle by the end of the century. Theirs is a complex history, subject neither to easy summary treatment nor to simplified models of development. I hope to be able, through the analysis of the evidence concerning cast iron, to show that one important strand in the fabric of gunpowder's history concerns the materials from which cannon could be made. This question is subject to a number of shades of meaning, because ""cannon"" can be made for many purposes under a profusion of different names, and under sharply varying conditions of use. As a result, the question of materials is frequently really a question of competing materials, and involves a complex set of factors, of which production costs and the ultimate safety of the user seem the most important. Judged in this manner cast iron was an important but unsatisfactory metal for weapons purposes until 1543, at which time English founders learned to make iron muzzle-loading cannon which could rival bronze ordinance in most important performance criteria, but which cost much less to produce. With that event, the history of cast iron and the history of weapons entered into the close relationship that persisted until the advent of rifled artillery made of steel in the middle of the nineteenth century."

Jan 1, 1983

By J. C. Kurnia

Methane is recognized as one of the prime causes of underground mine disasters around the globe. A cost-effective mine ventilation system and methane control is required to ensure a safe and productive environment in an underground mine whilst keeping energy usage and operating cost at minimum. Typically methane enters a mine environment or tunnel from localized distributed sources at high initial concentration. Hence, an understanding of its dispersion from discrete sources is important to design a methane management system via effective ventilation. This study employs computational fluid dynamics to model methane dispersion in an underground tunnel which has a number of discrete sources of methane and effective ways to dilute and or disperse it. Air flow distribution within the tunnel as well as methane dispersion is simulated by solving the governing transport equations subject to appropriate boundary conditions. First, the effectiveness of ventilation duct placement is examined. Several possibilities are explored and investigated. It is found that the common configuration utilized in underground mine performs best as compared to other configurations in maintaining the concentration of methane below permissible levels. Next, a novel intermittent airflow ventilation system is proposed and evaluated via simulation with the goal of reducing the energy cost whilst maintaining methane level in the mining face below the allowable level. Parametric studies are conducted to investigate effects of various factors influencing the effectiveness and performance of this novel intermittent ventilation system. This study will provide some new ideas for designing an efficient and effective underground mine ventilation system by lowering the net average amount of air that needs to be circulated in the tunnel for a safe operation. KEYWORDS

Aug 1, 2013

By J. Peace, J. R. Fletcher

"British Steel has increased its usage of stainless steel for bunker, silo and chute linings to reduce maintenance costs and improve productivity.A generation of low cost 12% Cr steels has been specifically developed to satisfy the needs of hardness, flow promotion and through life costing which are demanded by bulk solids handling industries.The range of stainless steels include:• a very hard martensitic grade which is particularly suitable for high stress applications where impact and abrasion are predominant;• a titanium stabilized duplex steel for structural applications, as well as low friction , medium abrasion resistant wear liner plate; and• a ferritic stainless steel with rubber backing for low stress application where flow promotion of product is the predominant requirement.Industrial applications and experiences along with methods of fixin g the stainless steels will be discussed in conjunction with the relative through-life costs of the products.IntroductionBritish Steel has become one of the most efficient steel manufacturers in the world, with improvements seen in productivity, quality, delivery, performance and response to the needs of the worldwide market place.Part of this success stems from reductions in engineering downtime in the key areas of its operations, by the introduction of better engineering design and the use of enhanced materials where significant cost benefits have been identified.The nature of producing iron and steel requires the use and handling of a number of raw materials with wide ranging properties, each calling for a different approach to solving the difficulties encountered in storing and transporting these materials to their respective point of use. Figure 1 shows steel production for 1988-89 where over 30 million tonnes of raw materials were handled in making 14 million tonnes of liquid steel at British Steel's five integrated works.Typically solid raw materials include, iron ore, coal, limestone, ferro alloys and scrap. Intermediate products such as coke and sinter create their own specific handling and wear problems.Coals and ores are shipped into the United Kingdom from several sources, and have a great variety of properties. Some coals can be extremely wet and sticky, whereas others are dry and dusty . The ores handled can vary from wet concentrate and fines to heavy angular rubble and pellets. These raw materials are off-loaded, stored and conveyed through British Steel's own port facilities at Port Talbot, Immingham, Redcar and Hunterston. British Steel also produces the majority of its own coke and all its own sinter. Coke and sinter are frequently handled at elevated temperatures which cause other handling problems."

Jan 1, 1991

By J. C. Li, Y. Zou, L. He

"The effect of rock joints is significant in characterizing dynamic behaviors of discontinuous rock masses. To reveal the relation between the transmission coefficient and the contact situation of the joint surface, an experimental study on stress wave propagation across an artificial rock joint was carried out using a modified Split Hopkinson Pressure Bar (SHPB) apparatus. All the bars and specimens were norite cored from the same site, and one surface of the specimen which contacted to the transmitted bar was sawn with a number of notches to simulate the artificial rough joint. According to a wave separation method, two strain gauges were mounted on each pressure bar at a specific spacing, then the incident, reflected and transmitted waves across the joints were obtained from the test data. It was found that the contact situation of the rock joint surface makes a different on the wave propagation. Finally comparisons of the transmission coefficients with different contact area ratios and different joint thicknesses were made respectively. The results show the effects of contact area ratio and thickness of joints on wave transmission.INTRODUCTIONJoints affect the dynamic mechanical behaviors of the rock masses significantly. When propagates across the rock masses, wave usually attenuates in amplitude and frequency due to the presence of the joint as a discontinuous interface in the rock masses. Rock joints are the main factor that affects the behaviors and properties of rock masses. Many researchers have focused on the mechanical properties of rock joints under quasi-static conditions. Nowadays, the effect of joint dynamic properties on wave propagation across rock masses is gradually taken into account in theoretical and numerical studies.The effective contact area, joint roughness, and properties of the asperities and filling materials have been found to influence the normal stiffness of joints (Bandis et al. 1983). As suggested by the International Society for Rock Mechanics (ISRM), the roughness of the discontinuities can be generally characterized by large-scale “waviness” and small-scale “unevenness” (Brown 1981). Many researchers focused on the roughness of rock joints that affects the mechanical properties of rock masses and wave propagation. For example, Brown and Scholz (1985, 1986) presented theoretically and verified experimentally a closure model of contact between two random nominally flat elastic surfaces, which showed that the joint closure property depended both on the surface topography and material properties. Pyrak-Nolte et al. (1997) presented the quantitative aperture data for three-dimensional interconnected fracture networks, which were imbedded in intact opaque rock samples several centimeters in length, using x-ray computerized tomographic (CT) imaging. Fardin et al. (2001) systematically investigated the effect of scale on the surface roughness of rock joints and concluded that samples should be equal to or larger than the stationary limit for surface roughness to be accurately characterized on a laboratory scale or in the field. Zhao et al. (2006) conducted excellent ultrasonic tests across intact cement mortar specimens, singlefracture specimens, and two-fracture specimens."

Jan 1, 2015

By D. G. Macintyre

"Potentially economic stratiform barite-sulphide deposits have recently been discovered in Devonian basinal facies rocks of the Kechika Trough of northeast British Columbia. This new mineral district is over 180 kilometres long and includes nine major occurrences, namely Driftpile Creek, Bear, Mount Alcock, Cirque, Fluke, Pie, Elf, Kwadacha and Sika. The Cirque is the largest known deposit, with reserves of atleast 30 million tonnes averaging 10per cent combined lead-zinc and 47 grams per tonne silver. The footwall rocks for the Cirque and other strati/rom barite-sulphide deposits in the area are rhythmically bedded baritic and pyritic carbonaceous black shales, siliceous argillites and cherts of probable Mid to Late Devonian age. These siliceous rocks overlie a succession of proximal to distal turbidites which are the basinal equivalent of Early to Mid Devonian carbonate reefs to the east. The siliceous facies is overlain by deeper-water black shales of probable Late Devonian to Mississippian age.Preliminary stratigraphic and sedimentological investigations suggest that the strati/arm massive pyrite and bedded barite deposits formed in third-order euxinic basins within a northwest-trending structurally controlled trough which, in the southern part of the district, was bounded by carbonate reefs. The exhalative event, which appears to have been accompanied by synsedimentary faulting, took place during the early stages of a major eastward-directed marine transgression that was probably related to rapid crustal subsidence. Dewatering of metal-enriched shales and subsequent brine discharge along fault zones within the trough, with the exhaled brines accumulating in seafloor depressions, is the mechanism envisaged for formation of the deposits. Convective circulation systems may have been established about the more deep-seated faults, in response to elevated heat flow levels."

Jan 1, 1982