Search Documents

By D. Sediako

Excessive residual stress in Al engine blocks may result in cylinder distortion which reduces engine operating efficiency. As such, neutron diffraction was used to measure residual strain along the Fe liners and Al, in the hoop, radial and axial orientations with respect to the cylinder axis, at the cylinder interbore region. Residual stresses were subsequently calculated using generalized Hooke's law and related to the microstructure along the cylinder bridge. The results suggest that the residual stresses in the Al interbore region are tensile and increased with depth in the axial direction of the cylinder. The increase in residual stress at the bottom of the cylinder coincides with a finer and more uniform microstructure in this region of the cylinder. The refinement in microstructure at the bottom of the cylinder likely increased alloy strength, thereby decreasing this section's susceptibility to distortion. This study successfully quantified the residual stress profiles in a heat treated engine block and related the stress profiles to an as-cast engine block.

Jan 1, 2011

By K. Schimann, H. D. Knipping, J. P. Fouques

"The Cigar Lake uranium deposit, in the Athabasca area of north Saskatchewan, was discovered in May 1981 by Cogema (Canada) Ltd., as operator of the Waterbury Lake Joint Venture.The deposit, which is devoid of direct surface expression, is located at the unconformity between the Lower Proterozoic (Aphebian) Wollaston Group meta-sediments and the Middle Proterozoic (Helikian) Athabasca sandstone, at a depth of 410 m to 450 m below surface.At the end of 1984, the deposit had been defined by 105 mineralized holes over a length of 1800 m and a width of between 25m and 105m. It has the shape of flat-lying /em 5 m to 30m thick and shows a remarkable longitudinal and lateral continuity from the information obtained to date. A well defined bulge of the unconformity underlies the mineralized zone over its entire length.The deposit appears to be controlled by an east-west trending structure within which a particular rock facies (""augen gneiss'') has developed in the graphitic metapelites of the Wollaston Group. It is surrounded by a strong alteration halo affecting both sandstone and basement, characterized by extensive development of Mg-AI rich clay minerals (illite-chlorite). The mineralization is hosted principally by the Athabasca sandstone, and consists mainly of uraninite and sulfa-arsenides of nickel and cobalt. Numerous geochemical and geophysical surveys have been carried out in the Cigar Lake area, and although no specific geochemical or geophysical anomaly can be directly associated with the mineralized body, there may be locally a good coincidence.However, a combination of several methods proved extremely useful in interpreting the regional geology and defining the drilling targets within the favourable areas.Although the Cigar Lake deposit shows many similarities with several classical deposits of the Athabasca region, it is characterized by the intensity of its alteration processes and the presence of massive, extremely high grade mineralization.At the end of 1984, the global geological reserves estimated by geostatistics on the main mineralized ""pod"" of the deposit amounted to 110,000 metric tonnes of uranium at an average grade of 12.2% U, with a precision of 25% at the 95% confidence level."

Jan 1, 1986

By J. Arzúa, L. R. Alejano, P. Rodríguez

"After six years of successful excavation with a support pattern, some roof failures have happened in a room-and-pillar underground mine excavated in a stratified rock mass. In this paper the authors give explanation to the failure mechanisms and redesign the support in order to solve the recent problems of roof collapse.The mine magnesite bed is approximately 14 m thick, and runs in the E-W direction with an average dip of 18º. Due to mine constraints and the inexpensiveness of the ore, the excavation is performed in the mineral itself, avoiding the need for mining dumps and waste excavation. Rooms and drifts are oriented in the mineral bed to form an angle of 19º to the direction of the strata, reducing the roadway gradients to less than 10%. Rooms are 11 m wide and pillars are 7 m wide. They are designed to leave a 1 meter thick magnesite bed in the roof of the rooms to act as a supporting beam. More often than not there is a layer of very poor quality marly shale up to 1 m thick resting on this magnesite beam. Overlying the poor quality marly shale there is a better quality, self-supporting sandy shale.First, a characterization of the involved rock masses (magnesite, marly shale and sandy shale) is performed, collecting the geotechnical data from previous studies and performing new in situ geotechnical surveys to check the soundness of the previous data. A distinction is made between different quality zones inside the mine by means of the RMR classification, associated to the occurrence of faults.Back-analysis of some of the failed rooms and data from exploration boreholes were used to determine the failure mechanisms (associated to Voussoir type failure or occurrence of sub-horizontal joints crossing the magnesite beam). Based on an understanding of these mechanisms, the method used to design the support and to analyse the stability of the different possible thicknesses of the magnesite beams of the rooms and drifts of the mine were improved.Numerical models of the most relevant conditions found in the mine were performed in order to better understand the behaviour of the roofs and to simulate the supporting solution obtained in the previous analyses.The most relevant conclusions with regard to the main elements causing the instability of the roof include the appearance of sub-horizontal discontinuities crossing the magnesite bed, which causes total instability of the roof and usually leads to collapse; excessive thinness of the magnesite beam in the problematic rooms; and the relaxation of the deepest (around 270 m in depth) zone of the mine because of existing faults."

Jan 1, 2015

By K. Bachmann, M. Rudolph, U. A. Peuker, H. H. Duong, T. Heinig, T. Leißner, H. Schubert, Helmholtz-Institute Freiberg for Resource Technology, Technische Universität Bergakademie Freiberg

"Minerals can be liberated by random fracture of particles into smaller fragments or by detachment along phase boundaries. These two mechanisms represent borderline cases. When ores get comminuted the liberation of minerals is achieved to some extent by both mechanisms. This article describes a method to determine the extent of transgranular and intergranular fracture on surface exposure of minerals based on 2-dimensional liberation analysis.The approach uses the non-biased surface information like phase specific surface area (PSSA), phase specific free surface (PSFS) and phase specific locked surface (PSLS) of minerals and their change with comminution. The amount of transgranular and intergranular fracture on surface exposure can be calculated using the phase specific surface parameters.A sedimentary rock (apatite ore), an igneous rock (nepheline-syenite) and an artificial material (copper slags) were ground to different fineness. Based on the mineral liberation analysis (MLA) of feed and products, the extent of phase boundary fracture on the surface exposure of the minerals is studied.INTRODUCTIONMinerals can be liberated ether by comminution or by detachment (Gaudin, 1939). Liberation by comminution is a random fracture mechanism, which is not being influenced by ore texture, grain boundaries and mineral features (transgranular fracture). Liberation by detachment represents a fracture along grain boundaries (intergranular fracture). Random fracture often is named as the dominating mechanism for the liberation of ore minerals. This has been the basis to simplify models for liberation modelling (Barbery, 1991; King, 1979; Meloy, 1984) assuming that the probability of cracks moving along grain boundaries is zero. Thus, no interfacial area is lost during comminution."

Jan 1, 2016

By T. S. Grewal, S. C. Gupta, H. Natarajan, T. W. McQuade, N. Nejibulloev-Mamedov

Cigar Lake is one of the world’s largest high-grade uranium mines. The ore mined at Cigar Lake is milled at Orano Canada Inc’s (Orano) McClean Lake mill. The average Cigar Lake ore uranium grade since the start of mining activities in 2014 is 17.8% U (range 8– 28%). To achieve budgeted production of 18 M lbs U3O8/yr the required average feed tonnage to the mill is about 45 kt/yr. Arsenic, occurring as arsenides and sulpharsenides, is one of the major elements of concern associated with Cigar Lake ore. The leaching process is a sulphuric acid leach under oxidizing conditions at near atmospheric pressure. The presence of arsenic in the ore consumes oxidant in leaching as well as ferric sulphate in tailings preparation for arsenic sequestration. The average arsenic grade since the start of mining at Cigar Lake is 0.57% As. Further, the ore is hosted in a matrix of sandstone and clay, which results in poor settling in CCD. The average uranium grade for the balance of Cigar Lake Phase 1 ore is expected to drop to 12.5% U and the average arsenic grade is expected to increase to 1.6 % As, with an annual average peak of 2.5%. Therefore the tonnage throughput required to sustainably meet the production target will increase to 55 kt per year. Orano partnered with Hatch Ltd. (Hatch) to perform a gap analysis study to identify key circuits and equipment in the mill that would require debottlenecking. A METSIM mass balance model of the McClean Lake mill was generated and validated with actual mill operating data. Various feed scenarios were then studied, and the outcome was a traffic light table, which highlighted feed scenarios that exceeded installed capacity of major equipment and circuits. The results provided the basis for the PDC for the pre-feasibility study. This paper will outline the results of the gap analysis, the mass balance model, the feed scenarios and the study undertaken to prepare the McClean Lake mill for the change in ore quality from Cigar Lake.

Jan 1, 2020

By E. H. Holm

"This paper is a market-oriented review of the industry's present and forecasted performance, considering some of the principal factors influencing natural resource development. The author illustrates the steady consumption growth of nickel, and stresses the need for a quantitative long-range approach to production, consumption and the supply/ demand balance on a worldwide basis. Objective consideration of this data exposes some popular misconceptions. The possibility of near-term undersupply of nickel is discussed in relation to historically rapid changes in inventories and demand patterns. What is the significance of the increasing reliance on lateritic sources? New• facilities, new processing methods and new product forms are illustrated as further evidence of the industry's determination to satisfy the needs and preferences of nickel consumers. Examples indicate how product forms must accommodate to fast-evolving end-use technology. A review of nickel's price performance is used as a base from which to explore tomorrow's price trends."

Jan 1, 1972

The recovery of fine hydrophilic gangue in flotation is related to the recovery of water. Water is carried by bubbles as a film and wake into the froth. The amount carried (entrained) depends on bubble size, gas rate and the subject of this paper, frother type. To isolate the effect of frother type from that of bubble size and gas rate, gas holdup is used as the correlating variable. Measurements were made using a bubble column (no solids) operated continuously with the overflow recycled. Continuous operation meant some foam depth was required to ensure only entrained water is recovered. Using an automatically controlled 7cm foam depth the overflow rate of water is used as a measure of 'water carrying rate'. It is shown that the common frothers can be grouped into four families based on the water carrying rate-gas holdup relationship.

Jan 1, 2006

By C. A. Pickles

Nickeliferous limonitic laterite ores contain considerable free moisture. In this research, the application of microwave radiation for the drying of this ore was investigated. The effects of sample mass, initial moisture content and porosity on the microwave drying rate were studied and the results were compared to those obtained with conventional drying. Microwave drying rates of two to three times the conventional values were achieved. Further enhancement of the microwave drying rate was realized by increasing the flow rate of air over the sample or by operating at reduced pressure. The high microwave drying rates were attributed to the inverted temperature gradient which resulted in internal heating and boiling and this in turn promoted movement of the water, both as liquid and vapour, to the surface.

Jan 1, 2005

By Michael L. Free, Shukla. Abhijeet

The short-circuiting tendency of a copper electrowinning cell (EW) based on the roughness of cathode deposits was investigated with varying parameters such as Cu concentration, guar concentration, current density, and temperature. A bench scale EW cell was set up to produce copper under conditions similar to industrial Cu EW. In addition, a statistical analysis and finite element analysis were performed to analyze the deposited thickness, surface roughness and maximum feature height. Interaction data for the cathode deposits suggest that current density and Cu concentration together affect the roughness of deposit more than the combined effect of guar and temperature. Model predictions of roughness were similar to experimental values. The predicted time to short-circuiting was similar to the measured time. This study provides an industrial relevant baseline against which new operating parameters can be compared.

Jan 1, 2014

By J. Béland

"Three stages, each characterized by a particular sedimentation, magmatism, mineralization and deformation, are recognized in the geological history of Gaspe. The first stage led to the formation of the Taconian orogen, the second to that of the Acadian orogen and the third stage to the accumulation of a post-orogenic cover. The Taconian orogen includes volcanic and detrital rocks of Late Precambrian or Cambrian and Lower to Middle Ordovician ages in which ultrabasic intrusions have been emplaced. Folding is severe. Mineralization is of the Cr-Ni-Cu type, related to the igneous facies.The rocks constituting the Acadian orogen include two distinctive sequences corresponding to two successive sub-stages. The second substage began in Early Devonian time with the first pulses of the Acadian orogeny. The rocks of the first substage grade southward from a nearly platformal sequence to an assemblage implying less stability and spotty volcanism. The second substage was one of synorogenic deposition of elastic rocks, first in a marine environment and later under terrestrial conditions. Granitic intrusions, surrounded by aureoles of skarn and hornfels in which Cu-Pb-Zn mineralization is found, accompanied the Acadian deformation. The second-stage"

Jan 1, 1969

The concept and practices of co-extraction of coal and methane have emerged in recent years to improve coal mining safety and productivity, utilise methane resources, and reduce fugitive emissions in environments that involve multiple coal seams with low gas permeability. The system of co-extraction integrates two previously separate operations of coal extraction and methane drainage. The coal mining operation reduces the coal seam gas pressure and creates strata fractures that enhance gas migration and capture from mine workings and surrounding coal seams. An effective methane drainage operation produces a consistent and quality clean energy product and, at the same time, reduces the methane concentration in underground workings and the methane content and pressure in the adjacent coal seams. This is a significant benefit in preventing gas explosions and outbursts, and promotes a safer and more productive coal mining environment. In addition, the co-extraction with enhanced utilisation of coal mine methane directly leads to a reduction in greenhouse gas emissions. Presented in this paper are key results and outcomes of a major Asia Pacific Partnership project carried out from 2008?2012 by the Commonwealth Scientific and Industrial Research Organisation in collaboration with Huainan Mining Industry (Group) Co. Ltd., to develop and demonstrate advanced technologies at Pansan mine, Huainan, that promote the concept and practices of co-extraction of coal and methane. A comprehensive approach was adopted to assess fundamental strata and coal seam methane conditions during mining, and optimise mining sequences and coal mine methane capture systems. The project has not only demonstrated a practical approach and procedures of advanced co-extraction of coal and methane systems but also delivered significant benefits and outcomes in improved mining safety and efficiency, increased methane capture and utilisation, and reduced fugitive methane emissions at the Pansan mine. The total mine gas drained increased from 25.36 Mm3 in 2007 to 47.0 Mm3 in 2011, and the mine gas utilisation increased from 4.94 Mm3 in 2007 to 21.15 Mm3 in 2011. The improved methane capture resulted in reduced coal and gas outburst risks and methane concentration levels at the mine workings, provided a safe working environment for coal production, boosted the mining efficiency, and eliminated methane related incidents over the last few years at Pansan mine.

Aug 1, 2013

By Mihaita Matei

An adaptive approach to control the deformation in tube hydroforming process is presented. This requires: the use of an existing non-linear FE software (ABAQUS) that incorporates a user material model (VUMAT), the development and implementation of an adaptive control strategy to coordinate the internal pressure and the axial load so as to prevent fracture and wrinkling failures (knowledge-base controller) and the application of the developed adaptive simulation approach for finding the optimal loading path required to hydroform a defect-free part with as uniform thickness distribution as possible (user's load subroutine (VDLOAD). In order to validate the approach, the case of conical hydroforming and the case of bending followed by hydroforming component is discussed.

Jan 1, 2011

By S. Banisi, M. Maleki-Moghaddam

Direct observation of charge shape and its motion in industrial mills is not possible; therefore, a combination of analytical and physical studies is used to determine charge trajectory. Software packages, which predict charge motion consider only the outermost layer of charge (single ball) and ignore the charge and the interactions of grinding elements. In the new version of the GMT (Grinding Media Trajectory) software, the effect of liners specification and bulk load on charge shape and trajectory are considered. The charge trajectory was measured in a laboratory mill with the diameter of 100 cm and length of 21.5 cm with the transparent end and compared with that of the old version of GMT. Four types of polyurethane rings were accurately machined to scale down the liners arrangements at two industrial mills. The model mill was operated at 55, 70 and 85% of the critical speed for five levels of mill filling (10, 15, 20, 25% and 30% by volume). The experiments indicated that the end walls effect was negligible for the model mill with the length of 10.8 cm and beyond. The proposed relationships to correct the trajectory and charge shape were validated by using the new liner of the Gol-E-Gohar iron ore company AG mill. The positions of shoulder, toe, toe departure and impact points were predicted with the relative errors of 5, 0.7, 2 and 0.2%, respectively. The GMT software was updated with the new relationships. The results of GMT simulation indicated that when the lifter face angle increased from 7 to 30°, the distance between the charge impact point and the toe decreased from 40.1 to 11.2° for 30% filling. The change in the position of the impact point meant increasing the probability of charge impacting the toe, not the liner which favored more efficient comminution practice.

Jan 1, 2016

By F. J. West

This paper deals with Jones & Laughlin Steel Corporation's new Adams mine, near Kirkland Lake, Ontario. After a brief discussion of ore structure, type, reserve tonnages, etc., the main body of the paper discusses the establishment of an open-pit limit based on economic considerations. The method used by J & L to arrive at an economically sound open-pit boundary its outlined fully. Physical limitations to open-pit boundaries are mentioned briefly. The paper concludes with a few remarks on the mining equipment in use and on its productivity

Jan 1, 1966

By R. M. Porter

PILLAR extraction at the Sullivan Mine bas been in progress for over twenty-five years and bas .involved progressively larger pillars. The largest pillar blasted to date exceeds one million tons and is described in this paper. This blast is believed to be one of the largest to take place entirely under-ground. The Sullivan Mine, owned by The Consolidated Mining and Smelting Company of Canada Limited, is located in the southeastern corner of British Columbia on the east flank of the Purcell range overlooking the twenty-mile wide Rocky Mountain Trench (Figure 1). The orebody is a bedded replacement deposit in argillites, varying in thickness up to 300 feet, but averaging about 80 feet. Above the 3900 Level, the dip varies from nearly horizontal to 40 degrees; be-low the 3900 Level it varies from 45 to 20 degrees (Figure 2). Pillar extraction follows a plan of retreating outward from caved areas. The size of each blast is determined by the effect which the removal of support

Jan 1, 1961

By T. M. Ahmed

Sherritt International Corporation experienced corrosion failures with the 316L stainless steel tubing in a high-pressure still condenser employed for ammonia recovery. A detailed failure analysis was conducted on the condenser tubing to determine the mode and the root cause of the failure. The analysis included both optical and scanning electron microscopy (SEM) of the inner and outer surfaces of the tube as well as characterization of the corrosion products using energy-dispersive X-ray spectroscopy (EDX). Results revealed that the corrosion attack was confined to the first ?100 mm of the tubing at the inlet where the tube was connected to the top tubesheet. The tube suffered both external stress-corrosion cracking (SCC) and crevice corrosion from the shell side (water side), and wall thinning of the inner surface (the tube side) due to erosion corrosion. It was evident that failure of one of the tubes occurred due to SCC that penetrated the whole wall thickness and resulted in a leak failure. Some prevention measures are proposed to avoid this type of corrosion attack in the future.

Jan 1, 2005

By C. Lapointe

"IntroductionTen years ago, when nuclear fission became practical, the element uranium, until then a not very desirable by-.product of the radium industry, became overnight the strategic material par excellence. One of the several important problems that had to be solved at that time was the rapid and precise determination of uranium in ores and concentrates.GeneralThe chemical analysis of uranium ores is a long and difficult business and is complicated by the presence in most ores of a large number of interfering elements. True, much progress has been made, during the past few years, toward simplification of the analytical methods, but the chemical determination still remains the job of a skilled operator. For this reason, the chemical method has been replaced, whenever possible, by a physical determination based on the measurement of the radiations emitted by the elements of the uranium family. There are several types of instruments suitable for these measurements, but of all the radiation detectors known to the physicist, such as ionization chambers, crystal detectors, scintillation, proportional counters, and the like, the Geiger-Mueller counters have proved to be the most satisfactory for routine determinations, because of their simplicity.The Geiger-Mueller counter is a very versatile instrument; it can be constructed to detect any type of radiation, corpuscular -0r electromagnetic. Here, however, we are interested in these counters because of their ability to detect the beta and the gamma radiations, both emitted by some members of the uranium family. The beta radiation is corpuscular, and is composed of fast electrons, while the gamma radiation is electromagnetic."

Jan 1, 1950

By R. A. Kipp

THE dry concentration of ores and minerals is a subject on which there is very little engineering literature available. With the advent of flotation, practically all milling research was turned to this development as it held the answer to large-scale economic operations. However, there are many concentration problems that can be more adequately and economically handled by the dry methods that have been developed, and, consequently, I believe it is very advisable for mining men to become fully 'conversant with just what can be done in the dry state. Therefore, today, I should like to give a brief summary of the processes that are available and, in a general way, how they can be a p-p lied. I shall confine my remarks mainly to two dry processes: THE Am FLOTA'l'ION TABLE AND THE ELECTROSTATIC SEPARATOR Dry Magnetic Separators should probably also be included, but I am

Jan 1, 1961

By Stanley Davidson

"The ore deposit mined by Falconbridge Nickel Mines, Limited, is one of the numerous nickel-copper sulphide bodies marginal to the large oystershaped mass of differentiated norite in the Sudbury district, famous as the world's most important nickel producing field. The unique character of the ore deposits of the district has resulted in its intensive geological study over a period of more than 50 years. The results of these studies have given rise to a voluminous geological literature and to a great deal of controversy as to the genesis of the ores. This description of the structural geology at the Falconbridge mine is presented in the hope that it may form a small part of the chain of evidence leading to a reasonably satisfactory explanation of the ore genesis.The mine, named after Falconbridge township in which the deposit occurs, lies along the southeast margin of the norite mass, which, however, is h::re concealed beneath a deep mantle of glacial sands and gravels averaging over 100 feet in thickness. As a consequence, the deposit was not discovered by the early prospectors, and it was not until 1916-17 that E. J. Longyear, of Minneapolis, located the ore by drilling(ll). The discovery was foreshadowed in 1899 by the work of Thomas A. Edison, who found indications of the deposit by what is believed to have been a combination of magnetic and electrical geophysical surveys. He sank a prospect shaft over what has to date proved to be the largest and richest ore section in the mine. A wet quicksand layer at the rock surface proved impenetrable, however, and the 'Edison' shaft never reached bed-rock.The Falconbridge property was acquired by the Lindsley interests in 1928, and ore output, since its inception in 1929, has gradually risen from a modest beginning to the present 2,000 tons and more daily. Total production in this period is 7,500,000 tons of ore averaging 1.72 per cent nickel and 0.89 per cent copper, together with a small but valuable content of precious metals, principally of the platinum group."

Jan 1, 1954

By P. L. Wright

"This is a brief history of the development of the mining project, with a description of the proven geology. The paper describes how the experiences gained progressively demanded change in the mine design. The equipment used is described, together with methods of working. Interesting facts have been proved regarding gas emissions and roof. supi;iort. The. working cycles evolved are completely flexible m operation and lend themselves to maximum utilization of the most productive units. The two underground mines are compared, showing the variance in conditions already experienced. Programs currently in operation to improve standards and production are: the training of miners, maintenance men and officials; experiments in floor consolidation and continuing roof support trials; and the effect of comparative stability of working crews on the performance of the operation."

Jan 1, 1973