Search Documents

By R. F. Dawson, A. S. Bagnall, K. Barron

"At Smoky River Coal Limited (SRCL), economic occurrences of structurally thickened coal deposits form attractive surface mining targets. These steeply dipping, structurally complex deposits require that special attention be given to pit wall design and operational practices.Where anchor support is feasible, there is potential for reducing footwall waste requirements and/or increasing coal recovery. SRCL has used rock anchors to support footwall slopes since 1985. This paper outlines design considerations and performance of rock anchor support systems at SRCL.Three case histories are included that illustrate the design process for supporting steeply dipping footwall slopes using rock anchors.IntroductionWestern Canada contains vast reserves of high grade coking coal largely located in two belts within the Rocky Mountain Foothills straddling the Alberta/British Columbia border. There are about one billion tonnes of ""clean"" coking coal reserves (Romaniuk and Naidu, 1986) situated near existing mining infrastructure. Within the reserve areas shown in Figure I, a total of six producers operate 10 large mines linked with ports situated on Canada's west coast. Al! of the producers operate conventional shovel/truck surface pits.Surface mineable reserves within some of the mountain coal mines are located on dip slopes or where the geologic structure has thickened the coal near the surface, creating low strip ratio targets. Footwall slopes in these mines are developed parallel to bedding, thus minimizing waste extraction and preventing undercutting of potentially unstable strata. The base of the mineable coal measures in both north and south regions is marked by massive quartz sandstone units (Torrens Member and Moose Mountain Member) which often form the footwall. Footwalls developed within this basal sandstone unit can attain very high unbenched heights often with little risk of instability. In cases where the footwall is developed on weaker strata above this basal unit, stability considerations control slope height when bedding dips exceed about 30°. In these situations it is desirable to assess the benefits of artificial support to increase the unbenched footwall slope height."

Jan 1, 1995

By Bahri Öteyaka, Ali Uçar, Oktay Sahbaz

"A Jet Diffuser Flotation Column (JDFC) is a newcomer flotation device whose operation principles similar with Jameson cell but it has an essential change in downcomer. By taking into account the hydrodynamic and fluid mechanic principles (Sahbaz et al. 2013) downcomer was changed as a diffuser, therefore turbulence at the end of the downcomer was reduced to provide better aggregate stability and homogenous dissipation of the bubbles in the separation tank. Thus the performance increase has been aimed for the coarse particles.According to theoretical results, obtained by the formula of Oteyaka (1993) showing the relationship between velocity gradient and maximum floatable size for the various contact angles, the d50 of quartz flotation of JFDC is about 240 µm and 310 µm for the contact angle of 50° and 60°, respectively. This result was verified by the experiments. According to the experimental results; d50 which was accepted the maximum floatable particle size of quartz flotation of JFDC was about 256 µm and 300 µm for the contact angle of 50° and 60°, respectively.INTRODUCTIONFlotation is a kinetic process used for separation of hydrophobic particles from hydrophilic particles. There are many different parameters affects the success of the flotation and particle size is one of them. While the flotation is very efficient for intermediate size, the efficiency of the process starts to decrease for both fine and coarse sizes (Trahar, 1981; Muganda et al., 2011). Therefore; researchers have tried to find a solution for the efficiency decrease in fine and coarse sizes by modifying the chemical condition and designing the new devices. For example, Jameson cell is a unique device for the fine particle flotation due to the suitable design and fine bubble producing (Jameson, 1988; Evans et al., 1995; Sahbaz, 2010). Because of this success operation the Jameson cell is applied more than 200 flotation plants in worldwide. On the contrary, the efficiency of the cell decreases for coarse particle flotation due to the turbulence occurred in the separation tank (Sahbaz, 2010; Cowburn et al., 2007). That’s why, new flotation device was designed in loboratory scale by Sahbaz, Oteyaka and Ucar in 2010s and it has been called as Jet Diffuser Flotation Column (JDFC) recently."

Jan 1, 2016

By Didier Fohlen

Three Policy Shifts to enhance IFC?s Accountability ? Comprehensive and dynamic treatment of social, health, safety and environmental risks ?Covers a range of risks encountered by clients in emerging markets ?Framework to anticipate risks and to address them as they arise ?Includes community development, biodiversity, human rights ... ? Effective principles to guide an outcomes-based approach ?By clients and IFC ?Focus on broad community support and value-added sustainable development initiatives Enhanced governance, transparency and disclosure

May 1, 2006

By M. Pötsch, W. Schubert

"The kinematic analysis of rock blocks is one part of a block stability assessment. It provides information about a block’s movability, i.e. if a block can detach from the adjacent rock mass and move towards the free space. This paper introduces an analytical method for the analysis of pure rotations of arbitrary finite polyhedral blocks. It enables the engineer to judge a block’s rotatability about a corner or an edge. The method is presented using a graphical and computational method. The application of the method is illustrated with an example. INTRODUCTIONThe kinematic analysis of rock blocks deals with the determination of the movability of blocks. Established methods typically cover: (a) translational motion (John 1968, Markland 1972, Londe et al. 1969, 1970, Goodman & Shi 1985, Warburton 1981) and (b) the specific rotational cases Toppling (Goodman & Bray 1977) and Slumping (Kieffer 1998). Mauldon & Goodman (1990, 1996) and Tonon (1998) introduced rotational kinematic analyses for three-joint pyramids and tetrahedral blocks extending Goodman & Shi’s block theory.All mentioned methods are subject to assumptions that limit the applicability to engineering problems. For example, the kinematic test of daylighting joints or intersections inherently assumes a finite block, which only can be proved by the finiteness theorem (Goodman & Shi 1985). Daylighting of an intersection or plane is not a sufficient condition for removability. Goodman & Shi’s and Warburton’s methods are limited to translational block motion. The methods for block rotations so far address tetrahedral blocks only. They also address only pure rotational modes and neglect the general motion of a rigid body. This paper introduces an analytical method for the analysis of the kinematic rotatability of finite rock blocks. It extends Mauldon's and Tonon's theory of rotatability of tetrahedra to arbitrary polyhedral blocks. A graphical method using the stereographic projection and a computational method are presented."

Jan 1, 2015

By E. R. Landry

This paper reviews the current state of electric furnace technology, with emphasis on some of the more recent developments. A large section of the paper is devoted to the use of increasingly high power inputs by arc furnace operators. Operating practices are then covered, including some of the newer techniques which have been tried.

Jan 1, 1967

By G. S. Hume

Introduction O WING to the mineral discoveries which have recently been made in the Great Bear Lake region and the possibility of the need for fuel for transportation and development, it seems.timely ro review available information regarding the oil prospects in the vicinity of Great Slave lake and Mackenzie river, where a vast area is underlain by Palreozoic and younger sediments that undoubtedly are petroliferous. Exploratory surveys were carried out in this area by the Geological Survey and others in the latter part of the 19th century, but it was not until 1920, when drilling for oil actually began, that any serious attention was paid to the oil prospects. This is readily accounted for by the remoteness of the region, the lack of quick transportation facilities, and the shore summer season. Numerous and copious oil seepages had been reported, however, from widely separated localities, and interest was stimulated by the knowledge that these occurred in Devonian strata which had given a remarkable record of sustained production of high-grade oil in the oil-fields of southwestern Ontario. . Accordingly, during the four years 1920 to 1923, inclusive, several parties sent out by the Geological Survey made as thorough an investigation of various parts of the area as seemed warranted at that time, and from these surveys most of our information regarding the details of the stratigraphy is derived. In such a large area, it is inevitable that the lithology and thickness of rocks of the same age would show wide variations, and hence it should be recognized that conditions as regards oil prospects in the vicinity of the west end of Great Slave lake are quite distinct from those that occur near Fort Norman, 400 miles farther to the northwest, and these again are in all probability quite different from those in the less well known Arctic Red River area, 250 to 300 miles still farther north.

Jan 1, 1932

By H. Higuchi

The Sumitomo Metal Mining Company Ltd. (SMM) started to produce electrolytic nickel at the Niihama Nickel Refinery in 1939. In 1992, the conventional matte electrorefining process was converted to the matte chlorine leach electrowinning (MCLE) process, which is currently in practice. SMM has mainly used two kinds of nickel matte as the raw material for the MCLE process. Treatment of new raw materials, which have different impurity contents from the original nickel matte, has become mandatory because of changes in the market. Therefore, the MCLE process has been required to increase its flexibility to treat the different impurity contents in the new raw materials. An increase in the capacity for iron removal is included in such requirements. A new iron removal circuit in the MCLE process, based on a process development study, was recently installed. The iron removal circuit is in operation, and efforts are currently underway to optimize the performance of the circuit by changing the present operating parameters. In addition to the removal of the iron, the application is also expected to improve the nickel recovery. The outline of the new circuit and the current iron balance in the MCLE process are described in this paper, together with the effect of the circuit on iron treatment capacity.

Jan 1, 2006

By C. D. Smith

Numerous studies have shown the potential of air rate profiling to significantly improve the flotation performance of a bank of cells. To date many profiles have been implemented; balanced, increasing, decreasing and combinations of these. Previous work has typically shown using an increasing air rate profile, where the air rates are increased proportionally to each cell down the bank, yields a higher grade for a given recovery compared to other profiles. Air rate profiling can then be thought of as having two distinct components; determining the correct distribution of a given volume of air and, perhaps more importantly determining the correct total volume of air to add to the bank. To date no method for this second component has been established. In an alternative technique the air rate to each cell is adjusted in order to optimise the air recovery from that cell. Air recovery is the fraction of the inlet air which overflows the weir of a cell as unburst bubbles. The peak in air recovery (PAR) is a robust measurement that indicates optimal performance for the operating conditions in the cell, and sets the PAR air rate. By doing this for each cell in the bank, the optimal total air rate to the bank and the optimal distribution of that air can be simultaneously determined. In this study plant trials evaluated different air rate profiles, and profiling based on PAR. The total air rates to the bank for all profiles tested were approximately equal, allowing direct comparison. The results showed that the highest cumulative mineral recovery was achieved by operating at air rates which gave the PAR for each cell down the bank. Different distributions of the same total air rate to the bank gave the same cumulative upgrade ratio, but lower cumulative recoveries. In this study, the increase in cumulative mineral recovery, at the same upgrade ratio, was more than 33%. Peak in air recovery (PAR) based optimisation of air rates to banks of cells and to the individual cells has been shown to significantly improve flotation performance as it simultaneously determines the optimal air rate to the bank, and the optimal distribution of that air.

Jan 1, 2009

By John Drobe, Robert M. Cann

"Abstract - The Minas de Oro Cu-Au skarn and replacement deposits are located in the highlands of central Honduras, 90 km north-northwest of the capital of Tegucigalpa.The deposits formed in Cretaceous volcano-sedimentary rocks following the emplacement of an early Paleocene granodiorite to dacite intrusive complex. Three types of skarn (Type IA, IB, and IC) and a low-temperature replacement mineralization (Type II) are recognized. Type IA skarn consists of massive brown-green andradite and lesser magnetite and pyroxene. Type IB skarn has magnetite + hematite as the main constituent and garnet <50%. Type IC skarn comprises >50% pyrrhotite + chalcopyrite with interstitial garnet or pyroxene. Au and Cu occur in potentially economic concentrations in all skarn types while other metals such as Ag, Pb, Zn, and Mo are locally present in significant quantities. The highly variable distribution and nature of the skarn deposits is controlled by: (1) intrusive activity, (2) composition of host rocks, (3) faulting and fracturing, and (4) attitude of host carbonates.Type II Au-Cu-As mineralization occurs in calcareous sandstone and conglomerate 2 km distal from skarns and comprises clots of Cu sulfides hosted within a zone of brecciation and quartz flooding. Garnet and/or magnetite skarn is not present and the mineralizing event appears to have been a low-temperature replacement type.The similarity of coeval Au-Cu-Fe skarns in central Guerrero, southern Mexico to Minas de Oro skarns, and the similar local stratigraphy is consistent with the generally accepted theory that the Chortis block originated from southern Mexico and during the Tertiary moved southeast to its present position."

Jan 1, 2000

By J. H. Archibald

"This paper describes the use of vector analysis for determining the intersection of mineral deposit veins. The mathematical evolution of the analysis is outlined.IntroductionMany mineral deposits can be characterized by sets of intersecting veins. Often a vein will have a steep dip and may intersect with another similar vein. Finding the intersections of these veins is usually done by graphical means. Structural geologists, by the methods of descriptive geometry, can usual ly predict where intersections of veins will occur. This method normally requires accurate drafting and layout of the problem and does not always lend itself to solution in the field.Another method for solving this problem involves the use of vector analysis, which is easily adapted to hand-held programmable calculators. It is assumed at the outset that the reader is familiar with the dot and cross products used in vector analysis. Two excellent references are cited at the end of this note for convenience.A plane, in general, is defined by three points. The points of interest here are the points where three vertical drillholes penetrate the vein, or plane, in question. The elevations of these three points are best referred to sea level. This requires knowing the elevation of the collar of the drillhole above sea level and the drillhole depth from the collar to the vein. The elevation of the intersection point is then found by subtracting the hole depth from the collar elevation. These three points now define the plane of the vein. A similar set of three points will define a second vein, and it is our object to show analytically their intersection if it exists."

Jan 1, 1983

Agenda 1.Energy consumption and energy costs ?focus and failings 2.Energy efficiency methodologies, people and supporting tools 3.Energy cost saving case studies from three minerals processing plants 4.The operations team and the supporting role of Operations IT 5.Conclusion: Reducing energy consumption and energy costs There are many good Energy Efficiency Methodologies ?Energy and GHG Emissions, Management Guidance Document, The Mining Association of Canada ?Energy Savings Toolbox ?An Energy Audit Manual and Tool, Canadian Industry Program for Energy Conservation (CIPEC) ?Lean and Energy Toolkit, Achieving Process Excellence Using Less Energy, www.epa.gov/lean ?Energy Efficiency Opportunities Assessment Handbook, www.energyefficiencyopportunities.gov.au

May 1, 2010

By M. S. Moats, F. Elnathan

"The effect of current reversal on two commercially manufactured electrodes (RuO2-TiO2 and IrO2-Ta2O5 coated Ti) in a chloride bearing electrolyte was evaluated. Accelerated lifetimes were found to decrease with increasing current density and increasing reversal frequency. Ru: Ti coated electrodes exhibited longer lifetimes than Ir: Ta coated electrodes even though they had one-third as much precious metal content. Chloride concentration did not affect lifetime in the range examined. Using energy dispersive X-ray spectroscopy (EDS), scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS), the failure mode of the electrodes was determined to be coating dissolution leading ultimately to passivation by the presumed growth of a highly resistive oxide at the coating/substrate interface.INTRODUCTIONCatalytic titanium anodes (CTAs) were developed in the 1960’s to replace graphite anodes in chlor-alkali cells. CTAs exhibited much better dimensional stability than graphite leading to lower operating potentials by promoting smaller electrode gaps and better operational efficiencies as they had to be replaced less often. CTAs are simply Ti substrates coated with precious metal oxides (such as IrO2 and RuO2) mixed with other components (such as TiO2 and TasO5) (Trasatti, 2000).CTAs are used in many other electrochemical industries, including water disinfection, wastewater treatment, cathodic protection and metal plating. RuO2 based coatings are typically used for chlorine evolution. IrO2 based coatings are for the most part utilized for oxygen evolution (Comninellis & Nerini, 1991; Forti, Olive, & De Andrade, 2001; Kotz, Stucki & Carcer, 1991; Trasatti & Lodi, 1981)"

Jan 1, 2016

By R. F. Dawson, A. S. Bagnall, K. Barron

"At Smoky River Coal Limited (SRCL), economic occurrences of structurally thickened coal deposits form attractive surface mining targets. These steeply dipping, structurally complex deposits require that special attention be given to pit wall design and operational practices.Where anchor support is feasible, there is potential for reducing footwall waste requirements and/or increasing coal recovery. SRCL has used rock anchors to support footwall slopes since 1985. This paper outlines design considerations and performance of rock anchor support systems at SRCL.Three case histories are included that illustrate the design process for supporting steeply dipping footwall slopes using rock anchors.IntroductionWestern Canada contains vast reserves of high grade coking coal largely located in two belts within the Rocky Mountain Foothills straddling the Alberta/British Columbia border. There are about one billion tonnes of ""clean"" coking coal reserves (Romaniuk and Naidu, 1986) situated near existing mining infrastructure. Within the reserve areas shown in Figure I, a total of six producers operate 10 large mines linked with ports situated on Canada&apos;s west coast. Al! of the producers operate conventional shovel truck surface pits.Surface mineable reserves within some of the mountain coal mines are located on dip slopes or where the geologic structure has thickened the coal near the surface, creating low strip ratio targets. Footwall slopes in these mines are developed parallel to bedding, thus minimizing waste extraction and preventing undercutting of potentially unstable strata. The base of the mineable coal measures in both north and south regions is marked by massive quartz sandstone units (Torrens Member and Moose Mountain Member) which often form the footwall. Footwalls developed within this basal sandstone unit can attain very high unbenched heights often with little risk of instability. In cases where the footwall is developed on weaker strata above this basal unit, stability considerations control slope height when bedding dips exceed about 30°. In these situations it is desirable to assess the benefits of artificial support to increase the unbenched footwall slope height."

Jan 1, 1995

By J. Robitaille, P. Cousin

"Agnico-Eagle Mines Ltd, Laronde Division, is a gold operation processing ore containing copper and zinc. Copper is recovered as a concentrate prior to gold cyanidation.Copper concentrate grade was improved with the implementation of an on-stream analyzer. Further improvements to the copper concentrate grade could be achieved throughefficient zinc depression.High cyanide cost linked to the copper content in the flotation circuit tails, prompted some modifications to the flotation circuit. Economics and environmental issues were considered. A Maxwell cell was retrofitted with an Outokumpu HG cell mechanism stabilizing it's operation. Secondly a flotation column was added to increase circuit capacity.This paper will address flotation circuit operation difficulties, successes and results achieved before and after modifications.RESUMELes Mines Agnico-Eagle division Laronde sont considéré comme étant un producteur d'or. Le minerai révèle toutefois des teneurs appréciables en cuivre et zinc. Un circuit de traitement combinant des étapes de flottation du cuivre et de cyanuration de l'or a été adopte. Le rejet de la flottation est lixivie pour son contenu en or.La teneur moyenne en cuivre du concentre final fut augmentée suite a l'implantation d'un système d'analyse en continu. Une séparation plus efficace de la sphalérite se devra d'être obtenue afin d'améliorer davantage la qualité du concentre produit.Le contenu en cuivre au rejet du circuit de flottation influence directement la consommation en cyanure. Pour cette raison, certaines modifications à la flottation sont devenues nécessaires. Des facteurs d'ordre économique et environnemental ont été considérées. Une cellule existante fut transformée en cellule HG d'Outokumpu, stabilisant son opération, et une colonne de flottation fut ajoutée au circuit afin d'accroitre sa capacité.Le présent document se veut une rétrospective des problèmes d'opération vécus, des solutions apportées ainsi que des résultats obtenus et de leurs implications suite aux améliorationseffectuees."

Jan 1, 1995

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Froth depth or interface level is an important control variable in column flotation which can influence both grade and recovery. A common method of locating the level is based on sensing the hydrostatic pressure at one or more points along the column. The level indicated can be in considerable error, largely because of variations in froth and collection zone bulk densities. A portable conductivity probe has been developed to detect the position of the interface from conductance measurements across the interface. The location of the interface corresponds to the position where a large change in conductance is observed, which is primarily a consequence of the difference in gas holdup between the collection and froth zone. This probe detects the position of the interface to an accuracy of ± 5 cm. The probe can be used while the column is in operation, which allows for on-line recalibration of the level detection system. Results obtained in its application in a pilot-scale column (0.91 m in diameter) are described.

Jan 1, 1990

By B. R. Casement

"Managing safety on the basis of after-the-fact reaction to accidents, can never be more than partially successful. Injuries will occur as long as the underlying potential for them still exists. Unless unsafe actions and conditions are systematically decreased, no program can have more than a short-term success.The pro-active Bullmoose loss control process, instead, focusses on heightening awareness of work habits, to prevent incidents by reducing their potential.Any safety program will be doomed to failure if the development of safe work habits depends on the safety supervisor or a safety committee. At Bullmoose the focus is on the critical actions out of which losses emerge. The successful application of performance-related feedback is achieved by taking safety, health, and environmental concerns into consideration on every level, and, by doing the right thing in every job done.What is an Exceptional Loss Control Program?If an accident in an organization creates a flurry of interest, resulting in ""cracking down"" on violations for a short period of time then an ""exceptional"" loss control program exists. Unfortunately, exceptional here does not refer to the effectiveness of quality of the program but to the fact that the organization is managing loss control by exception. The degree of management attention in an ""exceptional"" safety program varies over a period of time, remaining low as long as the rate of losses stays within management&apos;s acceptable control limit (Fig. I). When the losses rise above this, management becomes motivated to begin ""exceptional"" efforts to manage losses. When the rate falls again to within the accepted limit, efforts to control losses take a back seat.Such a strategy guarantees that losses will be tolerated or ignored as long as the actual rate is below the acceptable limit. Simply to lower the limit would not reduce losses, but would result in an increased number of flurries of management attention to loss control. This ""on-again, off-again"" style of management teaches supervisors and others that basic loss control is not as important as are statistics."

Jan 1, 1993

By Bryan Tisch

Goal of GMGE ??To advance mine reclamation through the beneficial use of organic residuals for the sustainable establishment of bioenergy crops and other productive land uses Objectives ??To advance the current ?standard? of mine reclamation by demonstrating that mining lands can safely become agriculturally ?productive? through the use of organic residuals. ??To generate and compile sound scientific data that can be utilized by stakeholders to better assess the environmental impacts of utilizing these materials. ??To complete a manual of best practices regarding the utilization of organic residuals on mine lands. *Considerable effort to be placed on operations/implementation side of utilizing residuals ?rather than just pure research

May 1, 2011

By N. Haghdadi, D. M. Maijer, A. B. Phillion

B206 is a recently-developed high-strength Al-Cu casting alloy with reduced Ti and Fe, as compared to the well-known AA 206 alloy, for improved hot tearing resistance. In the current study, the solidification kinetics of this alloy as a function of cooling rate from 1 to 15 K/min were studied using differential scanning calorimetry (DSC) and microscopy. Specifically, the evolution in fraction solid, grain size, and secondary dendrite arm spacing have been characterized. The DSC results show the occurrence of three peaks during cooling from the liquid state, which are related to the formation of primary aluminum, a pre-eutectic intermetallic, and the eutectic phases. Thermal analysis also indicates that while the liquidus temperature is not sensitive to the cooling rate, the temperatures at which the pre-eutectic and eutectic phases form are strongly coupled to the rate of heat extraction. A decrease in the latter temperatures was observed when the rate of solidification was increased, leading to a lengthening of the freezing range of the primary phase. The results will be useful for improving B206 casting processes, specifically through modification of mould cooling conditions.

Jan 1, 2014

By W. J. Mcgaughey, R. G. McCreary, S. C. Maxwell, R. P. Young

"Seismic tomography is a process for obtaining images or maps of seismic velocity or other seismic properties of a rock mass. Seismic velocity images reveal variation in elastic moduli which, in tum, are related to several properties required in the geological or geomechanical assessment of a rock mass. Seismic velocity is sensitive to lithology, discontinuities, and in situ stress. Spatial or temporal variation of these properties may be indirectly assessed. Tomographic measurements are sensitive to volumes of ground, rather than determinations at points, or along lines or surfaces, as in conventional geological or geomechanical measurements or mappings.Tomography surveys are complementary to conventional measurements as they have the capability to interrogate a substantially larger volume of ground. They are thus useful in discerning trends or patterns in regions between or surrounding conventional ""point"" measurements of lithology, rock quality, stress, or other parameters of interest. Seismic velocity images give broad indications of trends in velocity; their spatial resolution of ground properties is typically on the order of five to ten per cent of the nominal survey dimension.Research in seismic tomography has been carried out for several years, and the capabilities and limitations of the technique in mining environments are beginning to be understood. This report reviews the present capabilities of seismic tomography surveys in mining, emphasizing rock mechanics applications. Six case studies are used as examples to demonstrate the capabilities of the method in assessing lithological variation, density and orientation of discontinuities, and the effects of stress."

Jan 1, 1994

"Cambior currently has nearly 80 exploration properties, acting as operator on about 60 of these. The company&apos;s exploration budget has increased to over $11,100,000 for 1990. On-going efforts recently yielded a new gold discovery on the Douay- Vezza property, a joint venture project with Inco and Vior. Cambior continues to seek out new opportunities, recently acquiring an option agreement on the Sleeping Giant project in Quebec and four new exploration agreements in the United States, through its Reno office. Other nearly-concluded joint venture agreements have also given the company entries into Indonesia and Guyana.SummaryWhen it acquired SOQUEM&apos;s assets on August I, 1986, Cambior also acquired interests in 45 exploration projects. The subsequent mergers with Aiguebelle Resources and Sullivan Mines in 1987 brought the total number of exploration projects to 83, most of which are concentrated in northwestern Quebec. Cambior&apos;s strategy emphasizes gold exploration, and exploration activities were, therefore, initially limited to the Val d&apos;Or and Rouyn-Noranda mining camps, where Cambior has a large portfolio of properties. Approximately $25.8 million has been spent on surface exploration in this area since the formation of the company, resulting in the discovery of the Mouska deposit and four sub-economic zones on the Porcupine, Forbex, Bloc Sud and Flavrian project s. In 1988, Cambior became involved in projects in the United States to which the company expects to allocate about 38070 of its 1989 exploration budget."

Jan 1, 1990