Search Documents

By Chri Rule

"This paper tells the story of the rapid commercial application of stirred milling technology at Anglo American Platinum’s many Concentrators. The first stirred mill – a 10 000 litre IsaMillTM; the largest at the time, was commissioned in late 2003. The project development work was presented at SAG 2001. This operation was “proof of concept” and vindicated the decision to scale up the technology; allowing a rapid and extensive roll-out of mainstream regrind mills as well as several further flotation concentrate regrind mills, over the next six years.Currently 23 stirred mills are in operation with 64 MW of installed drive capacity – this paper describes the projects’ roll-out and the significant results achieved to date. Many operational problems have been solved along the way, some of these will be described. The introduction of the technology has seen a step change in metallurgical results and progressively decreasing operating costs."

Jan 1, 2012

By John Keay, Douglas R. Shaw, Gregory J. Olson

"The results are presented herein of on-going laboratory investigations of heap bacterial oxidation as a pretreatment method for the recovery of sulfide-encapsulated gold from ore samples of the Rhodes Mining Lahoca deposit, located in northern Hungary. The ore contains just over 2 g Ault and as much as 6% sulfide, mostly as pyrite. Laboratory aerated column tests conducted at Colorado Minerals Research Institute (CMRI) showed that mild to moderate biooxidation of the finely crushed ore occurred rapidly in approximately three months, with cyanide gold recoveries of up to approximately 60%. The results contrast cyanide gold recoveries of less than 30% from non-pretreated ore. Mineralogical examination of biooxidized residues indicated that the mechanism of biooxidation of crushed ore was related to microorganisms following pathways along structural anomalies in the pyrite grains. Such selective biooxidation is an important result to minimize the biooxidation and aeration time and effluent neutralization costs in a commercial operation.IntroductionThis paper describes the development of a heap biooxidation process for the Lahoca gold project The Lahoca deposit is situated in northern Hungary, at the site of a former copper mining area. Lahoca is a large tonnage, relatively shallow, deposit amenable to open-pit mining Lahoca has the potential to produce I 00,000 ounces of gold annually for at least ten years at its minimum reserve base.The laboratory test work conducted initially by Rhodes Mining NL demonstrated that the Lahoca refractory ore is amenable to whole ore and concentrate oxidative pretreatment and cyanidation. Capital and operating costs, however, for such milled ore treatments were considered relatively high. Rhodes Mining subsequently evaluated heap leaching methods, particularly heap biooxidation pretreatment, as a process route that promised superior economics suitable for exploiting lower gold grade refractory ores.This paper focuses on the laboratory column (simulated-heap) biooxidation test work, particularly the proposed mechanism of selective microbial oxidation, wherein only a small amount of the sulfides are oxidized sufficient to allow commercially acceptable gold recoveries by conventional cyanide heap leaching. Selective or minimal biooxidation of sulfides is considered important to minimize biooxidation time and aeration requirements, as well as acid effluent neutralization costs."

Jan 1, 1998

By Jaroslaw W. Drelich

Despite the success of DLVO and extended-DLVO models that have been developed for homogeneous and smooth surfaces, a vast majority of practical surfaces encountered in mineral ore beneficiation are typically rough at various scales; they are also typically heterogeneous. The interactions of gas bubbles with particles having rough and heterogeneous surfaces are much more complex than the commonly used DLVO or extended-DLVO models predict. The effects of surface roughness on flotation and colloidal interactions have been reported many times in the past, although a clear understanding of their origins has been lacking. To explain differences in colloidal interactions for spherical hydrophobic particles, a theoretical analysis of the interaction potential was carried out for a model rough particle interacting with a bubble surface in an electrolyte solution in this study. The attractive hydrophobic interaction potential was added to repulsive retarded van der Waals and repulsive electrical double layer interaction potentials. The rough microscopic particles were modeled as spheres decorated with nano-sized asperities. Parameters that reflect common flotation separation systems were selected for testing this theoretical model and computation of the energy barrier applicable to particle – flat bubble surface interactions. It was found that hydrophobic asperities with the height of only several nanometers can reduce the repulsive interaction energy by an order of magnitude. Theoretical analysis also reveals that surface coverage of microscopic particles by nano-sized asperities is important as well. The findings of this research suggest that manipulating and engineering the particle surface topography could lead to better control over flotation separation.

Jan 1, 2016

By Chen Bang, Xia Xiao’ou, Zhang Feng

"Ores with compressive strength lower than 150 MPa are usually easy to be crushed by conventional jaw crushers and cone crushers. However, for hard ores with compressive strength exceeding 150 MPa and 200 MPa and even up to 250 MPa, such as andesite, hard basalt and olivine, it is difficult to reach satisfactory crushing size and yield or difficult to meet service life and stability use requirements of quick-wear parts by using conventional crushers. As continued increase in ore mining depth and constant generation of new type materials, equipment demand for crushing hard ores becomes increasing high. A new type inertia vibrating crusher is designed. It is powered by a high-speed rotating vibration exciter and can obtain required crushing force by adjusting eccentric mass, eccentricity and rotating speed so as to crush various ores with high hardness. This paper introduces the design process of its structure and working principle, discusses the design calculation methods of vibration excitation system, vibration damping and energy storage system and other key mechanism and provides technical references for this type of vibrating crusher.DESIGN PHILOSOPHYThe conventional jaw crusher mainly acquires extrusion force from crank motion to realize crushing. The motor drives the eccentric shaft via the transmission device to bring the moving jaw to swing relative to the stationary jaw. When the moving jaw moves close to the stationary jaw, ores between them are crushed by extrusion; when the moving jaw moves away from the stationary jaw, crushed ores are discharged from the discharge gate at the lower end between the moving jaw and the stationary jaw.The conventional spring cone crusher and the hydraulic cone crusher mainly acquire extrusion force from cranking motion to realize crushing. The motor drives the eccentric sleeve via the transmission device, the moving cone shaft generates an eccentric distance to make cranking motion under the action of the eccentric sleeve. When the moving cone moves close to the stationary cone, ores between them are crushed by extrusion. When the moving cone moves away from the stationary jaw, crushed ores are discharged from the discharge gate at the lower end between the moving cone and the stationary cone under the action of dead weight."

Jan 1, 2016

By I. Stanoev, V. S. Stoilov, I. Gradinarov, E. D. Visariev, I. A. Bonchev, Aurubis Bulgaria

"Aurubis is the leading integrated copper group and the world’s largest copper recycler. In Copper smelter Aurubis Bulgaria (Pirdop), the residual copper in the slags from Flash furnace and Converters is recovered by flotation. The slag processing comprises: pit cooling, crushing, two stages grinding (autogenous and ball) and flotation. The copper concentrate is thickened and then is filtrated by vacuum disk filter. The thickener overflow is sent to settler for additional clarification. A resent throughput increase resulted in higher solid content in the thickener overflow due to insufficient thickener area. Different scenarios to overcome the issue were evaluated (new thickener, reagents and reconstruction). An increase of the thickening area by installation of lamella modules was chosen as the most promising option. Three lamella modules (1 m3 each) were installed in conventional thickener for the test. Number of sampling campaigns was done to evaluate the effect on solid content in overflow. Parameters of the dewatering cycle were collected during sampling campaign. The products grain size distribution was defined - thickener feed, thickener overflow with and without lamella. The thickener overflow with lamella modules has 2.12 g/L less solid content. The decrease was 71.8%. According to the tests results, the whole conventional thickener was reconstructed with lamella modules. The thickener area was increased by more than 400 m2.INTRODUCTIONIn Copper smelter Aurubis Bulgaria, the copper in slag from the Flash furnace and the Converters is recovered by flotation. The scheme of slag processing is crushing, two stage grinding (autogenous and ball) and flotation. Till 2010 the grinding cycle in the plant was in two stages: the first stage was AG Mill 70×23 working with a classifier and the second stage was ball mill 3.6/5.5 working with a hydrocyclone. In 2010 a new AG Mill 65×78 with hydrocyclone was put in operation in order to increase throughput of the plant. The second stage of the grinding cycle was not changed."

Jan 1, 2016

By Tatyana Alexandrova

The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Technological aspects of processing precious metal ores are examined in two respects: enhancing gold recovery from double refractory ores; and using carbonaceous ores on a production scale. The dispersed carbonaceous matter (DCM) present in concentrates causes the adsorption of [Au(CN)2]- complex on their surface during cyanidation process. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The possibility of rare metals recovery, including rhenium, from black-shale rocks, has been examined. Comparative assessment of analytical methods of rare metals detecting has been carried out. It has been proved that neutron activation analysis is a promising technique. It has been shown that colloid-salt fraction (nanofraction) with particle size less than 1000 nm makes up to 3 wt% of black shale samples and is extracted by water under special conditions. The use of water instead of chemically active reagents provides insolubility of the mineral matrix and fully reflects the colloid-salt element of the samples. To sum up, the justification of the choice of technology for processing of carbon-bearing ores is based on examining the type of carbonaceous matter and its adsorption behavior. When the content of carbon of high degree of metamorphism is considerable, it is possible to recover platinum group elements and rare elements from this type of ores. The obtained results predetermine the general guidelines for creating new methods and techniques of processing carbonaceous material for integral development of solid minerals in the mining and oilfield areas of Russia.

Jan 1, 2016

By Liguang Wang

The froth phase in flotation has received much less attention than the pulp phase despite the fact that froth stability plays an important role in determining flotation performance. Froth stability is largely determined by the stability of thin foam films, which in turn has a strong correlation with the critical rupture thickness (Hcr) of the films. In the present work, a new approach to predicting the Hcr values of thin foam films in flotation froth phase was proposed and examined. The Hcr values were calculated using an advanced capillary wave model with input parameters being surface tension, film radius, capillary suction pressure, and intersurface force. The intersurface force was estimated by using the Stefan-Reynolds lubrication approximation to fit the measured thinning rates of single foam films formed in a Scheludko ring cell, where the film radii were less than 50 microns and were kept constant during the film-thinning process. A comparison between the predicted and experimental Hcr values was made for the films with the use of sodium chloride as background electrolyte and in the presence of various frothing reagents such as methyl isobutyl carbinol (MIBC), polypropylene glycol with an average molecular weight of 400 (PPG400), and sodium dodecyl sulphate (SDS), at different concentrations and film radii. It was found that the model correctly predicted the trends of Hcr-versus-concentration and Hcr-versus-film radius curves. Moreover, the predicted Hcr values matched well with the experimental ones of the foam films containing either SDS or PPG400. For the foam films containing MIBC, however, the model overpredicted the Hcr values. The reason for this discrepancy was discussed.

Jan 1, 2016

By N. Morrison, E. J. Rogans, A. J. Macintosh, N. Schoeman

"The design of carbon-in-pulp (CIP), and carbon-in-leach (CIL) adsorption circuits has essentially remained unchanged since the early days of the carbon process for gold recovery. For CIP circuit the pulp residence time is traditionally fixed at one hour per contactor with a carbon concentration of between 15 and 20 grams per litre, and the counter current carbon transfer rates are in the region of 15% pulp recycle. For CIL, the pulp residence time is usually three hours per contact or, with lower carbon concentrations ( 5 to 10 grams per litre).The drawbacks of using the counter current CIP/CIL adsorption circuits are discussed using modeling developed for CIP/CIL plant design. Counter current CIP/CIL, circuits are then compared with the carousel method of adsorption circuit design.The use of equipment suitable for the carousel approach is discussed which is, the AAC cylindrical and pumping (MPS) screens, the AAC pump-cell plant and launder designs.Finally, two plants at the Vaal Reefs Gold Mining and Exploration Company that use carousel adsorption circuits, namely the Vaal Reefs No. 1 Gold Plant, a CIL plant with stepped contactors, and the Vaal Reefs No. 2 Gold Plant, a CIP using a very short residence time (AAC pump-cell) are discussed."

Jan 1, 1998

By H. Weissenbaeck, B. Nowak, M. Oesterreicher, R. Stastny

The producers of certain metals like nickel and cobalt increasingly face a shortage of easy-to-mine and easy-to-process ore bodies. Their focus is shifting towards alternative raw materials which in turn demand new, different extraction techniques. One potential route for processing a ferrous ore with a non-ferrous target metal is atmospheric leaching with hydrochloric acid followed by purification of the pregnant leach solution (PLS). For the separation of iron from the PLS, and, in turn, the extraction of the non-ferrous compounds, the following flow sheet is proposed. Pre-concentration of the PLS, oxidation of ferrous (if present) to ferric chloride, hydrolysis of ferric chloride leading to the precipitation of hematite and the evaporation of hydrochloric acid, followed by crystallization of non-hydrolysable metal chlorides by means of sparging hydrogen chloride into the solution. Hydrogen chloride required in the latter step is produced internally by super-azeotropic distillation of regenerated hydrochloric acid. The liquid filtrate from the crystallization step is recycled to hydrolysis. Depending on the specific composition of the PLS, the hematite produced contains only traces of other impurities, whereas the crystallized mix of non-hydrolysable metal chlorides – containing also the target metal in enriched form – contains ferric chloride only in an amount referring to the filter cake moisture. These crystals can then undergo further hydrometallurgical separation and extraction processes. As an example, this flow sheet is proposed for treating nickel laterite ores. Experiments related to the demonstration of crucial assumptions in the flow sheet are presented. Based on those experiments a mass and energy balance of the flow sheet was calculated and is presented here together with a table of the major consumables in order to provide a basis for an operating cost estimate and other process economics.

Jan 1, 2016

By Ian Sherrell, Michael Pirie, Riddhika Jain

"Conventionally, direct reduced iron (DRI) mixed with char from rotary furnace discharge is cooled down before separating the char via magnetic separator. The DRI must then be reheated for further downstream processing (i.e. smelting). Outotec has developed the PyroMagTM specifically to conserve thermal energy during this separation process. DRI is cleaned by feeding hot particles directly after reduction onto a rotating surface just above a stationary magnet assembly. This allows hot feeding of the clean DRI to the downstream equipment which renders the entire process more energy efficient.Continuous testing of the PyroMagTM was performed to verify design and separation. Because the use of DRI/char was not practical for test use, the pilot plant testing was conducted using a magnetite/sand mixture heated up to and beyond the Curie temperature of magnetite. The separation was efficient for both cold and hot processing with recoveries varying from 98.6% to 99.74%. As expected, the recoveries decreased to as low as 83.99% as the temperature was increased beyond the curie temperature of magnetite (585°C). Long term separation was thermally efficient and sustainable.INTRODUCTIONMagnetic drum separators are widely used in the mineral processing industry. These low to high intensity magnetic separators are used to concentrate various magnetic material, such as iron ore, and less magnetic materials, such as ilmenite and garnet from silica and other contaminantsThere are multiple classes of magnetism based on the effect that each material displays while in and out of a magnetic field. In a simplified fashion, which is more appropriate for mineral processing, the magnetic susceptibility of a mineral is used to define it as being ferromagnetic, paramagnetic or nonmagnetic. In this respect, minerals with varying degree of magnetic susceptibility can be selectively separated with different types of magnetic separation equipment in different stages of a process flow sheet. The lower strength magnets are employed early in the process to remove highly magnetic fractions. Later stages utilize greater magnetic fields for capture of less magnetically susceptible material."

Jan 1, 2016

By Janice Zinck, Ian London

In recent years, the secure supply of critical and technology metals has become increasingly important tomajor industrialized economies that seek to sustain their industrial base and develop advanced technologies, such as clean energy. Canada, with its significant reserves of rare earth element (REE) and other metals, has an opportunity to supply some of the global demand for these materials. However, to transition from promising mineral deposits to marketable products, investment in strategic research and development (R&D) and expertise is needed to address the complex technological challenges around the production, separation and processing of these metals, and to better understand the global market for these key commodities. To this end, in its April 2015 budget, the Government of Canada committed to invest $23M over 5 years to accelerate production of REE and chromite/ferrochrome. The goal of this program, developed in close association with industry, is that Canada contributes a sustainable supply of REE to the global market. The research and development program will provide the technological capacity to establish a Canadian REE industry. This paper will discuss REE R&D advances achieved in the first year of the program in areas of mineral characterization, beneficiation, leaching, separation and environmental management and will highlight the Canadian model of collaboration where industry (e.g. prospective producers, technology companies), government, academia and other stakeholders work closely to ensure that the R&D is targeted, innovative and effectively deployed and commercialized.

Jan 1, 2016

By Jacques Nantel

Mechanical-electrical personnel are present in all phases of the mining industry; the coverage is broad and diversified. Concepts of energy accounting are reviewed to pinpoint the sectors with a large energy consumption. Four sectors are reviewed: underground hard-rock mines, underground soft-rock mines, open-pit mines and mineral processing. In each sector, five or six technical innovations are analyzed as to their contribution to a more efficient use of energy.

Jan 1, 1979

By Dirk Claessens

The term ?cost? is too small when describing the destructive power of safety incidents for mining companies. Breaches in employee or environmental safety are felt way beyond the bottom-line: human life can be taken; ecosystems tarnished; the ire of peoples, media and government inflamed; significant halting of production; and high levels of legal and financial challenges. According to a recent survey of Mining executivesi, ?ensuring workforce safety? was the most important issues identified above any other, with a plurality of 31 percent, reigning above capital projects, product efficiency, and equipment reliability. We accept that safety is a most paramount issue, yet for many reasons we keep approaching the problem the same way we have in the past. We need to stop doing the same things decade over decade and try something new. New innovations are significantly changing the fundamentals of how mining companies explore, excavate, produce, refine and distribute their valuable commodities. Technologies such as visualization, analytics, location awareness, and gaming simulation are making these enterprises smarter. Now, attention turns to an area we?ve long held as integral to our business: safety. By using the same breakthrough technologies that are changing our business, we can now boldly imagine ? and credibly strive for ? a world of zero incidents.

Aug 1, 2013

By M. Bourassa, R. del Villar, S. St. Arnaud, J. Valenzuela

"Autogenous grinding is used quite frequently for mineral comminution as a result of its lower capital and operating costs. However, it is more difficult to control than conventional grinding, particularly when the autogenous or semiautogenous mill is the only comminution stage (i.e. no secondary grinding is available). Analysis of the control strategy used then becomes extremely important, a task that is greatly simplified by the use of an empirical dynamic simulator:This paper presents the methodology used in the development and the calibration of such a simulator for the autogenous grinding circuit of an iron are concentrator: The various steps are described: industrial data acquisition, preliminary treatment of the gathered information. and empirical modelling of the process. Finally, both the actual and the proposed control strategies are compared using simulation results.This exercise has shown that the variability of some of the controlled variables could be reduced through a better handling of the water addition and the use of filters on some of the signals used for control purposes. The reduction in variability of critical variables, such as power draw, would allow their average value to be increased without the risk of exceeding their safety values. Some advanced control techniques were also tested, with interesting results."

Jan 1, 1995

By Randolph A. Pax

"The internal operation of a tumbling mill is a very hostile environment and precludes the sustainable operation of internal sensors to measure the mechanisms of charge motion and breakage events. Instead indirect methodologies are required to expand the current understanding developed within a framework of perfect mixing of the mill contents. A number of measurement approaches have been successfully used to explore the operation of SAG mills including strain instrumented lifter bolts, mill shell strain measurement and thermal (energy balance) of operating mills.Early acoustics measurement was developed by Hardinge using a 'microphone' located close to the expected toe location. This signal was an indicator of the mill fill. Improvements were implemented with the use of two microphones straddling the toe location to try to increase the sensitivity of the measurement and reduce ambiguities. Further improvements included a filtered signal indicative of steel interactions. Unfortunately, the mechanisms of signal generation and the complexity of the processes do not provide a consistent signal.In recent years, advanced acoustic measurement using arrays of microphones utilising signal processing techniques have been implemented as SmartNoise and validated on over 30 mills. This paper will discuss the results obtained with signals such as water holdup, mill shell steel hits and two each of the toe and shoulder angles. An estimate of the internal mill component wear rates is also accessible.Advanced acoustic measurements with wide bandwidths when combined with physics models and process understanding has achieved a step change in the understanding of the dynamic internal operation of a tumbling mills on time scales of 80 ms. These techniques have been used extensively on SAG mills, but have also been applied to FAG and ball mills. Acoustic measurement is used for the rapid diagnosis of mill conditions and holistic control for optimisation and stability."

Jan 1, 2016

By Paul E. Mather, Matthew J. M. Krane

Anode or fire refining is the final pyrometallurgical step in the production of copper anode. Part of this process purifies liquid copper by reducing its dissolved oxygen with a natural gas-steam mixture. Until now there have been no transient models of this process coupling the injected gas jet mass transport with its chemical reactions. A transient, 1D flow, chemical reaction model was made to estimate the time-dependent behavior of anode copper composition, soot formation, and the transient gas jet composition along its height. Model estimates were made for reduction rate, soot emission rate, and exergy loss and destruction distributions for two melt temperatures and a range of steam addition rates. It was found that increases to melt temperature and steam addition rate increased reduction rate and decreased soot emission, while having little effect on exergetic performance. Estimates for reduction histories were compared to industrial data. INTRODUCTION Anode/fire refining is the final pyrometallurgical step in the production of copper anodes; it is essential for removing dissolved gases which cause porosity in cast anodes. Despite its significance, the open literature appears devoid of any transient models of the entire process; furthermore, there are very little published process data with which to validate any models made. This dual dearth of modelling work and process data inhibits studies of the tradeoffs between process and performance changes, desirable for decreasing reduction time and soot formation as well as quantifying changes in the exergy losses and destructions of the process. This work introduces a reduced-order, transient model of reduction during fire refining, examines performance trends with operating conditions, and compares model estimates with industrial data. Overview of anode refining The purpose of anode refining is to produce liquid copper which can be cast with minimal gas porosity, which disrupts the downstream electrorefining process. Dissolved sulfur is removed first, then oxygen, by reactions with different injected gases. The removal of oxygen (the reduction step) is the subject of this proceeding and is effected by the bubbling of natural gas, typically mixed with steam, through the melt from tuyeres. A typical refining run reduces dissolved oxygen from 3000 ppm to 300 ppm in 2–3 hours (Schlesinger, King, Sole, & Davenport, 2011). The refined copper is then cast as anodes. Figure 1 shows a schematic of the furnace vessel.

Jan 1, 2019

By D. E. Gill, A. Piche, S. Dufresne

"SOMMAIREUne méthodologie de prévision des coûuts de forage en galeries est proposée. Cette méthodologie a été élaborée pour les perforatrices pneumatiques manuelles. Elle est composée de quatre modèles: (1) un modèle de pénétration conduisant à la prévision du temps de forage; (2) un modèle d'estimation de la durée de vie des fournitures; (3) un modèle d'estimation de fa quantité d'énergie consommée; et (4) un modèle de calcul de couts. Elle fait intervenir la résistance en compression uniaxiale de la roche du massif foré, le diamètre des trous, Ie type de perforatrice utilise, fa pression d'air d'opération, la longueur des fleurets, les temps morts associes au forage ainsi que le rendement des compresseurs, des perforatrices et du réseau de distribution de l’air comprime. L 'application de la méthodologie est illustrée à l’'aide d'un exemple, suivi d'une courte analyse de sensibilité et d'une brève discussion. ABSTRACTA drilling cost estimation methodology for underground headings is described. This methodology has been developed for percussive hand-held drills. It comprises four models: (1) a drillability model used for the prediction of the drilling period; (2) a model for the prediction of bit and rod lives; (3) an energy model; and (4) a cost model. It makes use of the uniaxial compressive strength ofthe rock drilled, hole diameter, drill type used, operating air pressure, drilling rod length, dead times that may occur during the drilling operation as well as compressor, air distribution network and drilling machine efficiencies. The application of the methodology is illustrated with an example, followed by a short sensitivity analysis and brief discussion."

Jan 1, 1994

By T. Boiselle, C. Gielen, P. Henry, J. M. Bier

"Hydrometal is specialized in the production of zinc sulphate from complex secondary raw materials. Electric Arc Furnace (EAF) dust is one of the more interesting potential sources to produce zinc sulphate. In order to minimize waste quantities generated from EAF dust treatment, our R&D team has developed and patented a new process to recover the Fe contained in the dust as iron oxide product to be used and sold into the pigment market. The process is based on a specific reductive leaching step of the zinc ferrite contained in EAF dust, followed by a purification step to remove impurities (Ni, Cr, Cu...) and finally the controlled precipitation of the iron oxide. The aim of the iron precipitation step is to obtain the right shape and length of crystals in order to guarantee the right color and tinting strength of the pigment. The innovative aspects of the process results in the controlled oxidation of the iron to get the right crystal size and good purity material. The iron product can be valorized as red or yellow pigment often produced by the Penniman-Zoph process.INTRODUCTION A Few Words about HYDROMETAL Hydrometal SA (Engis, Belgium) is a subsidiary of Jean Goldschmidt International SA (JGI) in Brussels. JGI is mainly involved in metal trading activities (Goldschmidt, 1995). In 1985, JGI acquired the leaching circuit of a Belgian electrolytic zinc producer located in Engis, a few kilometers south of Liège, near the river Meuse and it was decided to name this plant: SA HYDROMETAL. Hydrometal is well connected by water, rail and road from its central location in the industrial region of Liege, in the heart of Europe. The company received in 1997 an additional license to process and recycle toxic and hazardous waste. Figure 1 shows a picture of the plant."

Jan 1, 2016

By L. Li

Iron removal is a common procedure in hydrometallurgy of non-ferrous metallic ores. Chemical precipitation and solvent extraction are currently the main methods employed for separation of iron from copper leach solution. However, chemical precipitation methods have the problem of producing large amounts of iron precipitates, and/or requiring high temperature and high pressure conditions for precipitation. The precipitates are difficult to separate from the solution. Emulsification is a general problem for solvent extraction, which causes loss of extractants and contamination of the electrolyte. A common problem for solvent extraction and chelating ion exchange processes is the difficult iron stripping process. Therefore, finding an efficient and environmentally friendly method for iron removal is of great significance. In this paper, new processes of using ion exchange resins to remove iron from copper leach solution have been investigated. Salicylic acid, amino carboxylic acid, amino phosphonic acid and hydroxy-oxime resins were employed to adsorb iron from a simulated copper leach solution containing 40 g/L of Cu2+ and 36 g/L of Fe3+. It was found that a hydroxy-oxime resin, named Z-Fe, has excellent adsorption selectivity on Fe3+. Desorption behavior of the resin was studied by two step elution using dilute H2SO4 and oxalic acid solution, respectively. After optimizing the adsorption-elution processes, the extent of removal of iron from the simulated copper leach solution using resin Z-Fe was 90%, while copper recovery could reach 100% in closed circuit processing.

Jan 1, 2016

By Gerhard W. Heinrich, Gerald V. Schroeder, Daniel A. Murphy, Daniel F. Suarez, Jamie B. Beauchamp

"Washwater 'Finger' sprays were installed and tested in the copper/nickel separation circuit at Strathcona Mill to improve flotation capacities and related metallurgical performances. The new spray design features submerged sideways introduction of wash water into the flotation froth through nozzles at the end of vertical pipes which are suspended from a header above the froth. This maximizes the effective cross sectional area of flotation vessels while maintaining effective froth cleaning and a desirably high density of the concentrate slurry. The plant tests gave increases of copper concentrate production rates of 17% to 20% for conventional cells and 16% to 20% in column flotation at target grades of 29% to 30% copper and of less than 0.5% nickel. Basic considerations and concepts of tests and evaluation procedures are described.IntroductionMeeting flotation concentrate grade targets at maximum production rates and recoveries is a challenge all too familiar to operators of base metal ore concentrators. Frothwashing is an option to improve grade/recovery performance by minimizing entrainment of impurities into the concentrate, which is commonly known since the sixties (Kaya & Laplante, 1989). It has been recommended for the flotation of sulphides and industrial minerals alike (Kaya & Laplante, 1989; Miller, 1969; Heinrich, 1989) and has found its ultimate application in flotation columns (Finch & Dobby, 1990). The washwater addition in a flotation column is most evenly distributed over the column's cross-sectional area thus ensuring almost complete displacement of feed water from the froth by a countercurrent washwater flow -provided, a positive bias is maintained. Therefore, flotation columns are ideal for cleaning flotation. However, there is usually less room for boosting the concentrate production capacity by increasing airflow or slurry level then with conventional cells because of the smaller cross-sectional area available."

Jan 1, 1994