Search Documents

By Robin Perry, Claude Bazin

"Discrete transfer functions which use the grinding circuit feed tonnage to predict mass flowrates at reagent addition points in a flotation circuit were calibrated using a dynamic grinding/flotation circuit simulator. Predicted mass flow values are multiplied by reagent addition ratios to obtain actual reagent flow. The transfer functions are currently integrated into the distributed control system of Les Mines Selbaie.IntroductionThe development of adequate tools for the control of flotation processes is a continuous challenge. Since the early 1970s there have been numerous publications dealing with practical aspect of control of flotation processes. Most plants use a combination of feedback and feedforward controls to reduce the effect of the following flotation process disturbances (McKee, 1991):• changes in throughput;• changes in feed grade;• changes in particle floatability (size, liberation, surface oxidation ... ); and • deliberate changes of setpoint;Feedforward control manipulates variables such as reagent and/or air flow rate to attenuate the effect of disturbances such as changes of feed rate and mineral content. The feed forward strategy is driven by measurements of these disturbances. Feedback control is used to maintain process variables to targeted set-points of concentrate or tails grades. The feedback control action is driven by deviation from the set-point, caused by a deliberate change of set-point or disturbances.This paper proposes a method to improve feed forward control schemes by the addition of a simple model for solids transportation. The feedforward strategy considered in this paper is the ratio type, in which the manipulated variable is changed according to a predefmed ratio between this variable and the measured disturbance. A typical example is the ratio of the reagent addition to mass flow of ore.The paper reviews the state of the art in feed forward control strategy applied to flotation processes and describes the method used for predicting mass flow rates. The last section shows an application of the method in the Les Mines Selbaie flotation circuit."

Jan 1, 1994

By M. Jackman

"Froth stability is critically important for an effective separation of fine and ultrafine particles using column flotation. While a desirable froth stability is required to facilitate the drainage of entrained gangue particles for secondary cleaning, excessively stable froths could create problems in separation efficiency and down-stream processing. In this work, we demonstrate that a stable foam was produced using a poly (N-isopropylacrylamide) (PNIPAM) solution at the temperatures below the critical solution temperature. In contrast, very little foam was produced at the temperature above the critical solution temperature (~32 oC) of PNIPAM. We can also tune the foam stability by changing the temperature of wash water. When warm water of temperature of 50 oC was applied, the foam collapsed and diminished. This is probably attributed to the switching of PNIPAM molecules from coiled to a globule conformation as the temperature is increased. Our results indicate that the foamability and foam stability can be tuned by tempartureresponsive PNIPAM. This is the first time that thermo-responsive PNIPAM has been shown to have potential as a modifier of froth stability in column flotation.INTRODUCTIONIn mineral processing, column flotation has become a more prevalent process in the separation of fine mineral particles (typically < 100µm). Traditional flotation cells are sometimes less efficient in selective separation of ultra-fine particles (Kohmuench et al., 2009). The efficiency of flotation columns is dependent on the froth stability at the top of the cell to drain the unwanted gangue particles entrained in the froth. The greater froth height in flotation columns, compared to mechanical flotation cells, gives a longer froth residence time, allowing more of the drainage process to take place before the froth reports to the launderer. Secondary cleaning, by applying a wash water shower to the froth, enhances drainage of gangue particles entrained in the froth, and improves the recovery of the targeted minerals (Finch et al., 2007).While a stable froth is desirable to facilitate drainage of entrained gangue particles, greater amounts of fine particles have been found to contribute to excessively stable froths which could create problems for down-stream processes (Bethell et al., 2012). Operators have tried spraying additional wash water on the froth, and reducing frother dosage to destabilize the froth and to prevent backup at the launderer. The former is sometimes inefficient, and the latter results in unacceptable recovery loss. Currently, the best practice is often the installation of larger froth launderers, adding expensive defoaming agents, and/or using deaeration tanks (Bethell & Luttrell, 2005)."

Jan 1, 2016

By Jan E. Nesset, L. Paul Staples

"High Gradient Magnetic Separation (HGMS) technology, although developed over 2 decades ago, has not been widely applied to the separation of sulphide minerals. Under conditions of strong magnetic field gradients, weakly magnetic minerals such as chalcopyrite (CuFeS2) and marmatite (Zn(Fe)S, sphalerite with iron in solid solution) behave paramagnetically and can be effectively separated from diamagnetic minerals such as galena (PbS). The application of this technology to the separation of Cu-Pb and Zn-Pb bearing streams in the treatment of fine grained complex sulphides may in some cases be more effective than separation by flotation. A 2 TPH Sala HGMS pilot plant was operated at Brunswick for a nine month period, ending in March 1995. The testing demonstrated the mechanical reliability of the technology, the consistency of operating results and the scale up from laboratory testing. HGMS is seen as a complimentary technology to flotation, best suited to performing those separations of galena (and other diamagnetics) which flotation does not do as well.IntroductionBackgroundSince the turn of the century, the magnetic character or magnetic susceptibilities of minerals have been determined with increasing precision and accuracy. Figure 1 illustrates specific magnetic susceptibilities of some common minerals. As long as susceptibility ranges do not overlap, separation is possible.In 1937, the principle of using a magnetizable matrix material in a magnetic field to increase both magnetic flux density gradients and number of capture sites for susceptible minerals was first applied (Frantz). It was not until the 1970's, however, that the genuine development of wet high gradient magnetic separation began with the introduction of very fine matrix materials to the magnetized volume of large solenoid magnets. Today, dozens of HGMS units purify, filter and separate minerals, primarily for the removal of iron stained minerals from clays used in the paper coating and china clay industries and for the recovery of fine titanium and iron oxides in the iron ore industry. Only the Garpenburg mill in Sweden is currently applying a continuous HGMS machine to separate complex sulphide minerals; upgrading a lead concentrate since 1988."

Jan 1, 1996

By Szilvia Szabo, Jozsef Paulovics, Ljudmilla Bokanyi

"Waste recycling is one of the most important challenges of the XXI century. The recycling of wastes is closely related to and bases on the mineral processing. Many mineral processing techniques and equipment are applied in this field. The principles of the characterisation of wastes and design of technologies is rather similar to the classic mineral processing. Nevertheless, the diversity of the wastes and their complex composition and properties, as well as their environmental impact requires a special approach.Solar elements have sandwich structure of glass substrate and cover, as well as a very thin semiconductor layer. CdTe semi-conductor can be recycled by flotation. Within the RESOLVED (LIFE European Framework) R&D project on the recycling of solar elements the surface properties of pure CdTe semiconductor and pure glass were investigated by the measurements of zeta-potential using Zeta PALS Brookhaven instrument at University of Miskolc. Applied surfactants were: potassium ethyl xanthate; the anionic oxhydryl Aero Promoter 825 or Flotinor SM 35; the cationic Armoflote 43 or Armoflote 64, as well as Hostaflot LET (dithiophosphoric acid diethyl ester) and Hostaflot M91 (mercaptobenothiazole). The tested electrolyte was sodium-silicate. Zeta-measurements were carried out in full pH-range. Interfacial interactions were detected and interpreted. The basic results were verified by the flotation kinetic tests.Finally, the flotation technological experiments were carried out at a semi-technical scale using the real obsolete solar elements. The particle size at the liberation degree of 98% was as fine as below 5 µm. A special flotation cell providing the generation and distribution of very fine air bubbles was built. The pre-concentrate for the manufacturing of the test solar module was performed and transported to the BAM Institute (Berlin), the principal co-ordinator of the Project, and then further to the First Solar (USA) where a new panel was manufactured using recycled semi-conductor."

Jan 1, 2016

By Changmiao Liu, Dong Dong

"Magnesite is a major mineral resource in China, whose output and export are massive and quite important to the world. Flotation performances of eight anionic collectors on magnesite were studied to find the proper ones. Micro-flotation results indicated that collectors of HOl, SDBS and AEP had outstanding flotation performances on magnesite, with the recovery ratio all reaching above 90% in a wide range of alkaline pulp. Solution chemistry calculation, Zeta potential and FTIR measurements were employed to reveal the interaction mechanism between anionic collectors and magnesite surfaces. Solution chemistry analysis indicated that the main active components of HOl, SDBS and AEP were anions and association complex anions in alkaline pulp. Magnesite surface was negatively charged in the alkaline pulp. The active sites on magnesite surface were mainly the components of MgOH-, Mg (OH)2, and MgCO3 when the pulp pH was over 8. Anionic components of HOl, SDBS and AEP reacted with Mg in magnesite surface to make the insoluble anionic salts. And the chemical adsorption was confirmed by the FTIR measurement evidences.INTRODUCTIONAs an important industrial mineral, magnesite has been widely applied in metallurgy, building materials, chemical industry, agro-pasturage and other fields (Hu et al., 2006). It is a major mineral resource in China with abundant reserves. Its output and export are massive and quite important to the world. Liaoning province is rich in magnesite, whose reserves and production both come first in China. So far the proven reserves have reached 2.91 billion tons, accounting for more than 90% of total reserves in China, and more than 25% in the world (Li et al., 2012).Magnesite ores in Liaoning province mainly contain crystalline magnesite, and the gangue minerals of quartz, dolomite, talc, tremolite, chlorite and carbonaceous materials. Some ores also contain a little pyrite, chalcopyrite, hematite and apatite. Most of the ores must be preprocessed to separate the useful parts from the large amount of gangue minerals, so that their value and industrial application can be enlarged and promoted.Flotation is commonly used to process the magnesite ores, and the conventional flotation methods include anionic and cationic flotation. In the former, gangue minerals of silicates were separated by using amine type cationic collectors. After the impurity minerals were removed, high qualified magnesite concentration could be gained. For the cationic flotation method, it had some drawbacks of lower recovery ratio and poor performance in the lower temperature pulp (Li et al., 1995)."

Jan 1, 2016

By V. Panayotov, M. Panayotova

"Finding a reliable relationship between fundamental properties of minerals of non-ferrous metals and their ability to float is extremely important. The approach presented in this work allows us to draw predictive models for an effective flotation, suitable choice of reagents regime and expected technological results before the minerals enter the flotation process. Attempts to adjust the technological regime in already begun flotation are often unsuccessful because the basic physicochemical processes have already taken place. Mineral processing can be optimized on the basis of objective and basic parameters, decisive for the efficiency of the process - the state of the surface of the mineral; assessment of: minerals flotation ability, the need to apply and the type of needed pretreatment, and expected technological results. The theoretical foundations of such an approach are presented in the work, as well as supporting them experimental results, and information on practical implementation in lead-zinc and copper-pyrite ores selection.INTRODUCTIONIncreasing impoverishment of ores of nonferrous metals incoming to the flotation and rising costs for obtaining the final product lead to the inevitable question - will the mineral processing process be beneficial economically, technologically feasible and environmentally safe and what is the way to improve its efficiency. Some of the possible solutions are already in practice - new more efficient and less energy consuming flotation machines and equipment, new - more efficient and selective reagents, new combinations of flotation regimens, and so on.Finding a reliable relationship between fundamental properties of minerals of non-ferrous metals (sulphides and oxides - most of them with semiconductor properties) and their ability to float is extremely important. This is the subject of research, started in the 60s of the previous century and continuing to the present day. Such dependence would enable a realistic assessment of flotation ability (flotability) of minerals before their flotation processing. The basic dependence, displayed by the researchers as Hoberg (1975), Chanturia and Shafeev (1977), Chanturia and Lunin (1983), etc., represents a relationship between bulk properties of minerals and their flotability, considering especially the concentration of the main charge carriers, namely electrons or holes. The bulk properties are practically constant for minerals from a given field. But the 'main arena' of the flotation process is actually the mineral surface (Carta, 1970; Rao, Labonte, & Finch, 1992; Panayotov, 1999; Rao, 2003; Hu, Sun & Wang, 2010). Therefore, we introduce a methodology for studying the surface of minerals, which methodology gives the degree of semiconductor bands bending on the surface and respectively - the charge of the mineral surface and its ability to interact with reagent-collector. The latter can be used to select the most optimal reagent for the corresponding mineral."

Jan 1, 2016

By James A. Deeks

"Motor failures and equipment bearing failures are responsible for reduced productivity.With the introduction of computers and data acquisition systems, users are now able to monitor, report and trend deteriorating conditions and take corrective action before a critical shutdown occurs.This paper discusses the monitoring and trend analysis of&apos; motors, and motor and equipment bearings. With today&apos;s digital electronics technology users are now able to monitor their equipment, detect deteriorating or abnormal conditions quickly, alarm the condition locally and or remotely, and decide if immediate corrective action is necessary or if it can be delayed until the end of a work Shift. All of this can be done long before any damage is done to the equipment.Monitoring Trend AnalysisIt is no longer necessary to compromise in selecting products, since state-of-the-art designs allow the adjustment in such small increments that the users are able to detect minute changes in a system&apos;s performance.Monitoring and trending of motors and equipment bearings is now available in economical packages which can be expanded as a system grows. Simply select the information you need, set the parameters, choose the scan time, and decide on the degree of reporting.Buffer storage of short-term monitoring of a number of analogue channels permit the user to view the recent history of motor data such as: motor average load, unbalance, motor current, ground fault, reserve thermal capacity, plus all of the settings of the protective device.A decision can be made to freeze the stored information after the motor stops or after the motor starts. Then the user is able to recall the conditions and diagnose the performance and the cause of the abnormal condition. Typical scan times range from ¼ second to 5 seconds ."

Jan 1, 1992

By P. Erskine

"Hyperaccumulator plants can be utilized as ‘metal crops’ in agromining operations. This emerging technology produces ‘bio-ore’ by growing ‘metal crops’ on sub-economic ore materials, such as natural ultramafic soils. In a typical application plant material is periodically harvested, followed by air-drying and incineration to produce the bio-ore intermediate. The bio-ore is of very high grade (>15 wt. % nickel), and of high purity, and may be processed into a number of different products (including nickel metal, nickelbased catalysts and pure nickel salts). Current research efforts from our team focus on Mediterranean climate field trials (Albania, Spain) and tropical climate field trials (Malaysia, Indonesia). Field-scale demonstrations are required to provide evidence of real-life performance and of economic viability. If the trials are successful, agromining may in the near future support local livelihoods with income opportunities as an alternative type of agriculture: to farm nickel.INTRODUCTION AND BACKGROUNDHyperaccumulators, plants with the exceptional ability to uptake and concentrate trace elements in their shoots, can be utilized as ‘metal crops’ in agromining operations (Van der Ent et al., 2013a; Chaney et al., 1998; 2007; Baker et al., 2010). Agromining produces ‘bio-ore’ from harvested ‘metal crops’ grown on unconventional resources such as natural ultramafic soils (Van der Ent et al., 2015a). The bio-ore is a high purity and very high-grade (>15 wt. % nickel) product intermediate that may be turned into a range of different nickel products (nickel metal, nickel-based catalysts and pure nickel salts). The potential for agromining is greatest in tropical regions (Asia-Pacific Region: Indonesia, Malaysia, Philippines, Papua New Guinea and New Caledonia) where very large expanses of ultramafic soils exist (Van der Ent et al., 2013b). Agromine operations may replace existing marginal agriculture on poor ultramafic soils, for example oil palm plantations that require high fertilizer inputs to be profitable, or take place under a cocropping regime. The ability of ‘metal crops’ to achieve high nickel concentrations in biomass (and hence in harvested bio-ore) from soils with just <0.5 wt. % nickel, makes it possible to access non-conventional resources, not accessible by traditional mining techniques. For example, agromining could be implemented both on the large ‘halo’ around the mine leases, and as part of the progressive rehabilitation process after conventional resource extraction. As with all methods for resource extraction, agromining will be finite due to the diminishing concentrations of nickel in the zone accessible by plant roots (Chaney et al., 2014). Nevertheless, considering soil materials with 0.2 wt. % nickel and ‘metal crops’ with a yield of 100 kg nickel ha-1 the agromining venture may be sustainable for decades (Van der Ent et al., 2015a)."

Jan 1, 2016

By J. Ji, A. Shi, B. Grcic

Floating copper minerals selectively against iron minerals such as pyrite has been challenging for most copper and copper/gold deposits, and many operations continuously strive to maximise copper recovery whilst meeting target concentrate grades. Maximising grade is achieved by selectively floating copper minerals and rejecting pyrite. This challenge is to minimise copper and gold losses in the roughers if this approach is used. A flotation testing program was conducted by Bureau Veritas Minerals on a high-level pyrite bearing copper/gold ore sample to establish the potential to reject pyrite in the rougher stage, but also maximise copper and gold recoveries, and ultimately final product grades. The test program included feed characterization, rougher and open-circuit cleaner flotation as well as locked cycle flotation tests. The main variables tested for achieving selective flotation of copper and gold were collector type and pH control, through lime addition. Grind sizes used in the rougher and cleaner tests had been established from previous test work. The collectors tested were SIPX, Aerophine® 3418A, Aerophine® 3421, Aerophine® 3422, Reagent S-11192 Promoter, Reagent S-11193 Promoter and FloMin C4150. The two best performing collectors were then tested in open-circuit cleaner tests, with the optimum conditions examined further in locked cycle tests. INTRODUCTION Bureau Veritas Minerals Metallurgical Division was retained by Eldorado Gold Corporation to perform a metallurgical testing program on a high-level pyrite bearing copper/gold ore sample from a gold- copper porphyry deposit to optimize flotation reagent scheme to improve gold and copper recoveries and copper content in the concentrate. The test program included feed characterization, rougher and open-circuit cleaner flotation as well as locked cycle flotation tests. Initially, various collectors were screened in kinetic rougher tests, and over a pH range of 8.5 (i.e the natural ore pH) up to 11.5, using a primary grind size of 80% passing 120 µm. The collectors tested were SIPX (sodium isopropyl xanthate), Aerophine® 3418A, Aerophine® 3421, Aerophine® 3422, Reagent S-11192 Promoter, Reagent S-11193 Promoter and FloMin C4150. The enrichment ratio, which is the ratio of copper to sulfur in the concentrate to that in the feed, was used as proxy for rating selectivity (i.e. degree of pyrite rejection or depression).

Jan 1, 2019

By V. Caps

Gold has been often used as an alloying component in order to increase or modify the catalytic properties of an active metal. For example, in the hydroconversion of methylcyclopentane, Riahi et al [1] shown that the addition of gold to palladium or platinum enhances the activity which becomes greater than that of the pure metals whereas the selectivity towards products resulting from ring expansion increases. Molenbroek et al [2] presented a detailed study on Ni-Au catalysts which exhibit activity for steam reforming and have been proved to be more resistant toward carbon formation than the pure Ni catalysts. Blocking of highly reactive Ni edge and kink sites by Au atoms is assumed to be the reason for the increased robustness of the Ni-Au catalyst. Nevertheless, the own catalytic properties of pure gold have been almost ignored up to the pioneering work of Haruta et al [3] which demonstrates the high activity of gold for CO oxidation at low temperatures. Other reactions such as WGS reaction, propylene epoxidation or benzene total oxidation have then been shown to be catalyzed by gold [4]. This discovery induced the publication of papers devoted to analyze the different factors controlling the activity of gold catalysts. Among them the most relevant appears to be the gold particle size, the nature of the support [5] and the preparation methods [6]. Clearly distinguish between support and size effect is not straightforward. Indeed, the calcination step often needed to synthesize supported catalysts on different supports, leads to different particle sizes showing that particle size and support are interdependent. To circumvent this difficulty, Au-based supported catalysts have been synthesized by using laser vaporization and low energy cluster beam deposition. The as prepared catalysts have then been characterized and tested in CO oxidation reaction.

Oct 1, 2003

By Zorigtkhuu Davaanyam, Fisher Wang, Bern Klein, Amit Kumar

"The High Pressure Grinding Roll (HPGR) is an increasingly popular energy efficient solution for comminution of competent ore deposits that primarily competes with conventional crushers and tumbling mills. A significant barrier to increased adoption of HPGRs is the requirement for large amounts (one tonne or more) of sample for pilot testing which may not be feasible for most early staged projects.Various researchers have worked towards developing piston-die and JK drop weight tests to model and predict the energy requirements for an HPGR. Two small scale laboratory test procedures (the SMC test (Morrell, 2009) and the piston press tests (Davaanyam, 2015)) have been developed in recent years to provide necessary information to size an HPGR.These two methods were used to estimate the required specific energy for an HPGR unit and compared to HPGR pilot scale test results from a copper deposit. The comparison provides insight into the benefits and limitations of these tests.INTRODUCTIONHigh pressure grinding rolls (HPGR) have gained popularity in recent years because of their energy efficiency in comminution. Various researchers have suggested that approximately 50–80% of the total energy consumed in a mineral processing plant is used by the comminution equipment (Haque, 1999; Abouzeid & Fuerstenau, 2009; Wang, 2013). Haque (1999) showed that the efficiency of grinding equipment can be as low as 1%. Due to the energy intensive nature of comminution, mining industry has been forced to explore alternative energy efficient processes.An HPGR based circuit has been shown to be 10–25% more energy efficient than a conventional SABC circuit (Von Michaelis, 2009; Wang, 2013). A significant barrier to the increased adaptation of HPGRs is the requirement for a large amount of sample for pilot testing (up to 5 tons), even on a prefeasibility level. Numerous studies have been performed to utilize piston press test to analyze the performance of the HPGR circuit and to predict the energy consumption for an industrial application. This paper uses two small scale laboratory test procedures, the SMC test and a piston press test, to compare the energy requirement to the pilot HPGR data."

Jan 1, 2016

By H. T. John

"The objective of this paper is to demonstrate how the optimum cut -off grade can be calculated for typical large tonnage openpit mines. In the examples, it is assumed that the concentrator tonnage is fixed and that there are no market restrictions. The mining rate is assumed to be variable. This is usually the situation at an operating property.ModellingA model of the ore body is required to examine alternate cutoff grade strategies. The model must be accurate in its relationship between grade and tonnage. Table I shows a typical relationship between ore tons and grade for various cut-off grades. The average strip ratio is also shown. For higher cutoff grades, the ore tonnage is decreased and the ore grade is increased. Strip ratio increases with the cut-off grade.Using the relationship between ton s and grade, and assuming a homogenous, long life orebody, a simple calculation of the optimum cut-o ff grade can be made. The objective is to maximize the present value of cash flows. For the long life homogenous orebody example this objective is satisfied by maximizing present cash flows.Cash flow is calculated by subtracting operating cost from revenue . Operating cost will increase with the cut -off grade as the strip ratio increases."

Jan 1, 1985

By Stavros A. Argyropoulos, Radhakrishna Valiveti, Bernard Closset

"The use of microprocessors in metallurgy is currently increasing at a very fast rate. A large number of companies are offering systems ""off the shelf"" which are aimed at the data acquisition and process control market. There are two main drawbacks to these systems: first, they are usually quite expensive, and second, they are not completely compatible with the target metallurgical application. An alternative is to develop a microcomputer-based system "" in lab "".A dedicated microcomputer system has proved to be very useful in many metallurgical research applications(1,2)). However, in this system the analog input signals had to be transferred over long distances , and significant noise was introduced despite the use of shielded cables. In order to overcome this problem a network of low pass-filter s was designed and built. The usage of the abovementioned system brought the need to digitize the analog signals in-situ and transfer the digital signals, which are much less susceptible to noise over very long distances. This distinctly different design philosophy has become a reality with the evolution of microprocessor technology over the last few years. This design philosophy is utilized in this development."

Jan 1, 1984

By J. Mizera, B. Adamczyk-Cieslak, K. J. Kurzydlowski, A. Dobkowska

"AZ31 is the one of the most popular magnesium alloy using in the modern industry. It is well known, that compared with steel, magnesium alloys posse better properties, such as light mass, high specific strength or thermal conductivity. It should be noted that their application is limited by poor corrosion resistance. In this work the corrosion behavior of AZ31 magnesium alloy as cast and after heat treatment were described with the use of testing in neutral salt spray atmosphere.To characterise corrosion resistance and describe layers built on the surface it was necessary to do the metallographic observations with the use of optical microscopy. After that influence of heat treatment for AZ31 corrosion resistance was examined. Measurements were conducted by electrochemical impedance spectroscopy (EIS) and by neutral salt spray tests in artificial atmosphere. Surface and cross section morphology after removal of corrosion products were observed with the use of scanning electron microscopy (SEM).The weight loss measurements show that there is no significant difference between alloys as cast and with following heat treatment.INTRODUCTIONMagnesium and magnesium alloys are popular in modern industry because of the low density and good formability. Magnesium alloys are described by few properties which have got significant influence for their application in transportation and electronics industries (Feliu & Liorente, 2015). Their wide application is limited by poor corrosion resistance. As it is well known Mg is one of the chemically most active metal. Corrosion resistance of Mg alloys depends on several factors, such as impurities, chemical composition or working conditions (Cheng, Qin, Wang, & Zhang, 2009). That all causes that there are many different ways to find well defined and good solution of magnesium alloys processing to improve their corrosion resistance.There are many different versions about the influence of aluminum on the corrosion resistance of magnesium alloy. It is known that intermetallic compounds such as Mg17Al12 due to ß-phase content plays the minor role for corrosion resistance. It is proved ß-phase acts as cathode and it has good ability to build passive layer in broad pH ranges. However it should be noted that mentioned behavior depend on size and distributions of ß-phase in the microstructure (Singh, Singh, & Das, 2015)."

Jan 1, 2016

By A. J. W. Law

"This paper deals with the organization of the central office technical areas and the role played during the feasibility studies, construction and operating phases of Les Mines Selbaie.HistoryThe Engineering Department was originally formed as a part of the Exploration Department, to examine the feasibility of advanced exploration prospects being brought to the company. In 1968, with the discovery of the South Bay property in northwestern Ontario, the department became part of a Mining Division and was expanded, so that it could provide more advanced mine feasibility studies, control of construction engineering and procurement and initial mine design. As is generally the case, the mine design function was handled with in-house capability, while plant, mill and const ruction functions used outside consultants.The 1974 discovery of the Selbaie deposits, started a period o f growth in the capabilities o f the department. The complex nature of these deposits, required that skills were added in the mining, metallurgical and plant areas. During the early feasibility study period these skills were provided by the engineering company of the parent group, but when it was realized that production from the deposits was likely, permanent staff was added."

Jan 1, 1990

By Gerhard Kircbner, Boen Tan

"IntroductionThe Key Lake uranium-nickel ore deposits are located in the Athabasca Basin of northern Saskatchewan, Canada (Fig. 1). Many papers have been published on Key Lake in the past (Dahlkarnp and Tan, 1977; Kirchner and Tan, 1977; Kirchner et al., 1980). Immediately after its incorporation in 1968, Uranerzbergbau GmbH, a German holding company, set up exploration subsidiaries in Australia, the United States and Canada. This account reviews those exciting years starting with the concept to explore the rim of the Athabasca Basin in Saskatchewan, and leading up to the discovery of the deposits in 1975 and 1976.A few summary statements can be made:• The discovery of Key Lake resulted from a very systematic exploration approach and the persistence of Uranerz, the operator. • Cluff Lake and Rabbit Lake had been discovered some seven years before, but it was the discovery of the Key Lake deposits which brought Saskatchewan to the forefront to become Canada&apos;s foremost uranium producing province.• The experiences gained at Key Lake, which were subsequently published, triggered the discovery of many other deposits of similar, or even larger, size than Key Lake. The spatial relationship of those deposits to graphitic conductors and hydrothermal alteration zones are presently the most effective indicators for locating new deposits - indicators which were first recognized at Key Lake.• Key Lake is, and will remain for some years to come, the largest producing high-grade uranium mine in the world."

Jan 1, 1994

By C. B. Webber, L. S. Diaz

"The paper presents the approach taken by Craigmont Mines to grinding circuit control. A detailed description is given of a fully automatic control system which bases its control actions on the continuous measurement of particle size in the cyclone overflow stream. The control system holds a specified particle size in the cyclone overflow, and grinds rod mi 11 ore feed at increased rates. The principles of operation of the system used for continuous measurement of particle size are described, end the improvements in mill throughput and copper recovery over several months of continuous operation are presented.INTRODUCTION Craigmont Mines Limited is located in the south-western interior region of the province of British Columbia, approximately 230 road miles north-east of Vancouver, and ten miles west of the town of Merritt. A moderate climate, good roads and service facilities provided by the Canadian Pacific Railway, Inland Natural Gas Company, and the B.C. Hydro and Power Authority, have provided a very favorable mine and plant site.The preliminary metallurgical design of the Craigmont mill was based on the test results of samples obtained from the original 2500' level drift during 1959. Pilot plant runs and other research testing for design pur¬poses were conducted at the Canadian Exploration Ltd. Laboratory, at Salmo, B.C. The design flowsheet was altered in progressive stages from 2,000 to 3,000, and finally 4,000 tons per day as the ore reserves became better defined. Construction work on the 2,400' level mill site commenced in late 1960. The official opening of Craigntnt Mines Limited took place on September 15, 1961, a little over two years from the time of the metallurgical assessment of the original ore samples.Mill throughput to date has varied widely both on a daily and a monthly basis, due to the varying hardness of the mine ores. The grindability af the ore appears to be related to the oxide iron content, which varies from lows of 9% to highs of 20%. Daily tonnage has ranged from 5,000 tons per day with 10% iron in the feed, to 6,000 tons per day with 20% iron feeds."

Jan 1, 1973

By R. Phillips, A. G. Doll, D. J. Barratt

"The Bond low energy impact (crushing) work index test is specified to be performed on rock specimens between 50 mm and 75 mm in effective diameter. NQ-diameter drill core, frequently used in mineral exploration programs does not meet that specification, it being 45 mm diameter or less.This paper reports the effect of performing the impact test on contiguous sections of HQ diameter and NQ diameter core, exploring the hypothesis that the contiguous intervals give equivalent results in spite of the core diameter difference."

Jan 1, 2012

By J. Bouchard, R. del Villar, A. Vazirizadeh

"Industrial flotation is a continuous and often multistage process, where particles of a given mineral species (usually the targeted one), present in different sizes, encounter a large amount of gas bubbles (normally air) to produce mineral–bubble aggregates, which are removed from the flotation device (cell or column) as a valuable product (concentrate). The bubble content inside the cell is characterized by the prevailing hydrodynamic conditions (known as gas dispersion variables), which in turn are known to influence the flotation performance. Although most researchers and practitioners agree that the relationship between the hydrodynamic variables and flotation performance exists, the lack of an adequate method foronline measuring the average bubble diameter has prevented such studies.The aim of this study is to apply appropriate hydrodynamic variables for flotation kinetic modeling (as a key feature of flotation performance) for a given introduced particle size distribution (PSD). In this regard, experiments were conducted in a laboratory flotation column (5.6 cm internal diameter for a total height of 650 cm), and mixtures of quartz (hydrophilic gangue) and talc (naturally hydrophobic mineral), classified in four different size fractions. The correlation between the flotation rate constant and given hydrodynamic variables were analyzed. Results suggest that the relative importance of hydrodynamic variables for flotation rate modeling depends on the PSD. Finally the suggested hydrodynamic variables for each of the various particle size-classes considered were used to produce single variable models for the flotation rate constant. INTRODUCTIONIndependently of the prevailing flotation conditions, the mechanisms for bubble-particle aggregation and the residence time of the phases inside the device must also be considered. In this regard, one of the most used approaches to represent the overall flotation process is as a pseudo-chemical reaction between a particle and a bubble, whose rate (at a given time) is proportional to the amount of remaining floatable species. The proportionating constant is called the kinetic constant or the flotation rate constant."

Jan 1, 2016

By David Minson

On many occasions, operators have seen that high density and paste thickener performance does not meet the initial design expectations, and the installed equipment produces lower than expected thickener underflow solids content. This lower-density tailings slurry leads to more water and lower beaching angles being seen at the tailings storage facility (TSF). This not only reduces storage capacity, but also increases the risks of non-compliance with environmental permit constraints. Reasons for the shortfall in performance can be many, but perhaps the main problem is inadequate understanding of the critical components of thickener design and operation, with too much reliance placed on standardised design terminology; such as tph/m2. This paper discusses additional factors that influence high-density thickener operation and presents test work that defines “Dynamic Slurry Fluidity”, “Bed Compaction Rates”, and “Natural Slump Angles” for these high yield stress/viscosity slurries. Finally, the paper uses this data to define thickener geometry, drive torque, floor slope(s), rake blade configuration and how this can be used to provide engineers with more tools for in depth evaluation of a High-Density thickener design. INTRODUCTION Generally copper mines are high tonnage operations, with copper flotation concentrators producing high volumes of tailings slurries of milled solids and water. As a result, Tailings Storage Facilities (TSF) become very large and this, along with potential scarcity of water, favours a design that maximises storage space. In theory, the use of filtration equipment that achieves immediate water recovery, high TSF in-situ densities and high stacking angles are preferred for this duty. However, large tailings filter units are uncommon, and have high operating and capital costs that favour the use of thickeners. The use of high-density thickeners to produce a thick or near-paste like slurry with high un- sheared yield stress values above 100 Pascals, is becoming more common. The higher thickener underflow is required to not only maximise water recirculation within the mill, but to also increase beaching angles, maximise tailings storage capacity and minimise evaporation losses arising from large areas of superficial water. However, the reliability of this equipment is also under scrutiny and there is perhaps a need to better define these designs.

Jan 1, 2019