Search Documents

By L. McFarlane, D. Rollwagen

"Madawaska Mines produces a uranium precipitate (83-85% u3o8) using a magnesium oxide slurry to precipitate the uranium from solution. The solution, at approximately 9""0 g/l u3o8 is neutralized to a pH of 7.0. At the Eldorado Nuclear Refinery in Port Hope, the precipitate is not acceptable as a single feed to the refinery process. It was discovered that a 2% silica impurity caused emulsion problems in the solvent extraction column.After extensive studies of possible solutions, such as two-stage precipitation and solvent extraction, an acceptable solution was found. The selective precipitation of uranium at a pH of 3.5-4.0 using Hydrogen Peroxide produces an almost silica free product of higher purity (90-93% u3o8) to that of straight magnesium oxide precipitation. Introduction Madawaska Mines Limited is located four miles southwest of Bancroft, Ontario. The annual production of u3o8 is approximately 610,000 pounds. To produce the final product or yellowcake, nine separate steps are required. These are (1) grinding, (2) dewatering, (3) leaching, (4) acid filtration, (5) clarification, (6) ion exchange, (7) precipitation, (8) washing, and (9) drying and packaging. To illustrate these steps, a complete flowsheet of the mill is displayed on page three.The yellowcake is sent to Eldorado Nuclear Limited in Port Hope, Ontario for further concentrating and refining. As part of their routine specification check, a test called the amenability test is performed. This test indicates how a particular dissolved yellowcake product reacts to solvent extraction. The Madawaska yellowcake did not pass the test."

Jan 1, 1982

By J. Mosher, G. Banini, J. Hollow, A. Villanueva

Prior to installation of High Pressure Grinding Rolls (HPGR) at PT Freeport Indonesia (PT-FI) a series of laboratory tests were carried out to determine the design parameters and also determine key performance indicators (KPIs) for the industrial unit. The design parameters derived from the lab test work were then scaled up to estimate the industrial capacity of the HPGRs to be installed. These parameters include specific power draw, specific throughput, and specific force, rolls speed, product size distribution and wear rate of the rolls. This paper compares the performance of the scale-up procedure against the installed industrial size HPGR. Overall, the specific throughput of the industrial size HPGR is higher by a minimum of 30% compared to the expected scale-up value. As a result of the high specific throughput, the specific power draw and grind sizes are below the scale-up expectations in the commercial application. The impact of these factors also contribute to a lower than expected wear rate on the industrial rolls. Installed rolls achieved a service life in excess of 18,500 hours relative to the target of 6,850 hours predicted from the laboratory testing.

Jan 1, 2012

By Morris J. Viljoen, David R. Young

"The zone of economic interest at H.J. Joel Gold Mine is the VS5/Beatrix Composite Reef, a quartz-pebble conglomerate of Archean age. The reef occurs at the base of the Eldorado Formation, Central Rand Group, of the Witwatersrand Supergroup. At least three stratigraphically distinct conglomerates form this economic zone. In order of deposition these are the Footwall, Beatrix, and the VS5/Beatrix reefs. The Footwall and Beatrix reefs are equated with the Aandenk Formation with transport directions toward the northwest, whereas the VS5lBeatrix Reef is of Eldorado age, with transport directions toward the south. The change in the drainage direction was caused by a major basin-wide tectonic event that occurred prior to the deposition of the Eldorado Formation. The Beatrix Reef was formed in a proximal, braided, fluvial environment by a process of aggrading gravel bars between channelways. The VS5/Beatrix Reef was formed by the desegregation of pre-existing Beatrix Reef with the introduction of new material containing much shale detritus and is seen to have been deposited in a more -distal, braided, fluvial environment, similar to the Beatrix Reef.The average gold concentrations are different for each conglomerate; the Beatrix at 32.1 ppm Au, the Footwall at 24.4 ppm Au, and the VS5/Beatrix at only 12.4 ppm Au. A sedimentary gold concentrating process related to higher energy braid channels was primarily responsible for these high gold grades. Not only the basal unconformity surface, but also, internal degredation surfaces, were prime sites for concentration. An understanding of the spatial distribution of these differing conglomerates and their braid channels forming the economic reef zone is necessary in predicting ore grades for future mining."

Jan 1, 1994

By Graham Swan

The case is presented for the development of a spray-on liner for ground support, but only in the context of a new mining system, consistent with the technical and business case advantages of liners compared to alternatives. Over the past 10 years much effort has been expended in specifying and testing the mechanical/environmental properties of various liners, without actually fulfilling any mining system requirements. The results have been generally disappointing, with no consistent and sustained application in a dayto- day production environment being achieved, anywhere. Central to this shortcoming has been the failure of mining/liner ma nufacturing companies to realise that screen/mesh or shotcrete cannot simply be replaced with thin, deformable liners: success will depend upon closely defining and evolving a new, liner- functional mining system. The paper begins with a discussion of some fundamental technical capabilities and constraints associated with 3M Canada?s liner material that has been developed in partnership with Falconbridge Limited. Intended applications for this liner include the support of bursting ground associated with deep mining conditions. With safe application and consistent performance in mind, the paper argues for a new mining system that derives in the first place from best quality drilling and blasting practices. Taking this as a given, a system for waterscaling and liner application prior to mucking out is proposed, followed by bolting through the liner while arranging for the bolts to be explicitly connected to the liner. Some logistical and equipment related challenges of such a mining system are then reviewed and discussed in the context of the business case for liners. It is concluded that this approach, if successful, will provide the greatest benefits in the areas of safer mining, due to reduction in worker exposure, and in reduced mining cycle times.

May 1, 2003

By H De Beer

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Nov 1, 2011

By G. Molloy

The purpose of this paper is to demonstrate the value of applying continuous improvement, in particular 5S and standard work, in an underground environment. 5S and standard work are two aspects of Lean manufacturing that have been applied in many industries. At Vale Canada Limited, the focus is to first stabilize the process, commonly through the use of 5S, standard work and other continuous improvement techniques. In parallel with building an engaged workforce, these approaches aim to incrementally stabilize and improve a process. 5S is an employee-driven, systematic methodology to reduce waste in all its forms through attaining, maintaining, and improving workplace organization. Identified as a foundational part of any improvement process, 5S aims to remove wastes that impact on the overall efficiency of the area. Standard work is used to formulate a common approach to how tasks are carried out to ensure consistency. Standardization involves identifying, establishing, and following the best method. The aim is to eliminate the variation that can occur when there is not a pre-defined established standard. Demonstrating the value of 5S and standard work in an underground environment will be achieved by first understanding the overall concept of Operational Excellence and continuous improvement as practiced within our operations. The paper will then cover a real application of 5S and standard work within the underground environment at Thompson, Manitoba.

Aug 1, 2013

By Miguel A. Cuba

Trends in the mean and/or variance are a longstanding challenge in mineral resource modeling. Geologic modeling and/or grade domaining are often employed to account for heterogeneities in mineral grades; however, this is only practical up to a certain point since the number of data available for reliable model construction can be severely reduced. In such cases, trends remain present in certain geologic/grade domains and directly impact the modeling methodology; the trend must either be handled explicitly or a suitable approach is adopted to implicitly account for it. This is highly dependent on understanding the source of the trend. We propose an approach that detects the source of non-stationarity, which is based on quantifying the impact of non-stationarity in the mean and the variance via the semivariogram. By expanding the methodof- moments approximation of the semivariogram, we decompose the experimental semivariogram is into three terms: 1) trend in mean component, 2) trend in variance component and 3) stationary component. We can then assess the source of trend by calculating the contribution of each component at every lag. Two cases are presented to illustrate this tool. Firstly, a synthetic reference model is simulated and different trend patterns are added; the influence of these patterns in the experimental semivariogram calculation are analyzed and discussed. Secondly, a real dataset is considered where the impact due to the presence of trends in the mean and variance are assessed. The results of this paper reveal the semivariogram to be a tremendously powerful tool in determining the source of the trend. This insight may be useful in the selection of a suitable modeling approach for resource estimation.

Oct 1, 2009

By EJ. Reichhardf

The Molopo Farms Complex is a major, layered ultramafic/mafic, early Proterowic intrusion which is totally covered by sediments of the Karoo and Kalahari Fonnations and situated in southern Botswana and northeastern South Africa. The approximately 3000 m thick, generally fine- to medium-grained ultramafic and mafic cumulates are intrusive into equivalents of Thmsvaal Supergroup sediments and lavas. Multiphase defonnation resulted in tilting and segmentation of the Complex into individual tectonic blocks. Sr isotopes document at least two chemically distinct parental liquids which interacted in a complex manner to form an approximately 1000 m thick rhythmically layered succession which straddles the ultramafic/mafic boundary. Repeated mixing resulted in a complex cryptic layering pattern and numerous sulfide-enriched layers which contain significant PGE+Au concentrations.

Jan 1, 1994

By Bonnie Cooper

3D printing by fused deposition can be used on lunar soil. The soil can be precisely size-separated to make the 3D printing process work efficiently. Using a MASER instead of a LASER would allow us to use the finest fraction of lunar soil, AS-IS, to manufacture things on the Moon.

May 1, 2013

By J. H. Curran

Agenda ? Challenges of developed world mining ? Software aids for creative and practical engineering ? Rocscience software philosophy ? Rocscience suite of geomechanics programs ? Case study ? design of de-stress slot Mining Challenges of the Developed World ? Dwindling reserves ? Great depths ? Strict operating and environmental regulations ? Competition from lower cost operations in developing countries

Apr 1, 2005

By J. C. Ingles

"A survey of possible methods for controlling cyanide concentration indicated that the simplest method would involve the use of a potentiometric technique. Such a method was suggested by a paper from the laboratory of Mines Safety Appliances, which described a method for determining hydrogen cyanide in air. In this application, the cyanide was absorbed in caustic and a silver electrode immersed in the caustic solution provided a measure of the cyanide concentration. However, our attempts to use the silver electrode in this simple manner to measure the cyanide concentration of solutions were not very successful. A study of the mechanism by which a silver electrode responds to cyanide concentration made it evident why this simple procedure is not satisfactory.Basically, the silver electrode provides an indication of the free silver ion concentration of a solution, and generally speaking, ignores the other ions' present. It can be used to measure an anion if this anion complexes silver. This technique has been used in complexing studies to determine the activities of such anions as acetate, citrate, oxalate and chloride. To do this, the electrode has to be placed in a solution which initially contains a known concentration of free silver ions. Addition of the complexing anion causes a drop in the free silver ion concentration and hence a change in the potential of the silver electrode. The change in potential can be expressed in terms of the concentration of the complexing anion, and used to indicate its concentration in the solution being analysed. The determination of chloride-ion by a silver-silver chloride electrode is an example of an application of this technique. The solubility of the silver chloride with which the electrode is coated provides the initial free silver-ion concentration. Depression of this free silver-ion concentration by the presence of the excess chloride ion of the sample solution results in a change in the potential of the electrode which is proportional to the chloride-ion concentration."

Jan 1, 1965

By Colin E. Dunn

Abstract-Plants have a remarkable ability to select, use and store metals derived from the substrate. Each species is unique in its requirements for and tolerances to the full spectrum of chemical elements in the Periodic Table. Studies to define the chemical characteristics of common trees and shrubs of the temperate forest are providing insight to their use for exploration, i.e., biogeochemical exploration. Examples of surveys over gold deposits in British Columbia show the effectiveness of sampling various tissues from different species in a range of biogeoclimatic environments. At the Nickel Plate mine in the Montane-Spruce zone, outer bark of Lodgepole pine was effective in defining a large area of metal enrichment; at the Carolin mine in the zone of Coastal Mountain Hemlock, analysis of twigs of western hemlock and Pacific silver fir provided an exploration target considerably larger than that defined by lithogeochemistry; at the Mount Washington gold deposit in the Mountain Hemlock zone, twigs of mountain hemlock and rhododendron were used to outline the mineralization; and in the Interior Douglas-fir zone at the QR deposit analysis of Douglas-fir tops collected by helicopter provided a rapid and effective method of identifying a gold-rich area.

Jan 1, 1995

By Engin Burak Anil

Objective, accurate, and fast assessment of damage to buildings after an earthquake is crucial for timely remediation of material losses and safety of occupants of buildings. Laser scanners are promising sensors for collecting geometrical data regarding the damaged states of buildings, as they are able to provide high coverage and accuracy at long ranges. Yet, we have limited knowledge on the performance of laser scanners for detecting earthquake damage, and requirements of such data collection. This paper focuses on characterizing the performance of laser scanners for detecting thin cracks for damage assessment of reinforced concrete frames. We identified a series of crack parameters based on the state-of-the-art damage assessment codes and standards. Similarly, we identified parameters, which affect the performance of laser scanners for detecting cracks, based on prior research in this area. We studied the width, depth, and orientation of cracks; sampling interval of the scanner, and the range of the laser beam from the surface. Effects of these parameters on the detection of the minimum crack size were determined in an experimental setting. An automated algorithm was used to analyze the data. The results show that it is possible to detect as small as ~1mm cracks.

Aug 1, 2013

By Sadan Kelebek, S. O. Fekete, Gerhard W. Heinrich, Peter F. Wells

"For many years, rejection of pyrrhotite at the milling stage has been a viable method for sulphur dioxide abatement. Pyrrhotite rejection options have included the use of selective pyrrhotite depressants in flotation; a depressant which has recently come into use is diethylenetriamine (DETA). This reagent has been the subject of recent research and development efforts in the processing of nickel-copper sulphide ores.In the present study, adsorption trends for DETA have been monitored under the dynamic conditions of flotation using a spectrophotometric method which has been adopted for this purpose at Falconbridge Limited. The results indicate that the adsorption of DETA is quite fast and in the majority of cases, accounts for the disappearance of 75-95 % of this reagent from pulp's liquid phase. The adsorption decreases linearly with an increase in the DET A dosage from 100 git to 600 git. The tailings produced in flotation tests were subjected to washing with deionized water at 60 °C to examine the desorption of DET A. These results indicate that the amount desorbed increases with increasing DETA dosage used during flotation but is less than 7 per cent of that adsorbed. It was found that adsorption of DETA alone, even at relatively high levels, does not always cause depression of pyrrhotite. A new combination of reagents identified in the metallurgical laboratories of Falconbridge Limited utilizes sulphur dioxide with DETA. These reagents together are capable of efficient depression of pyrrhotite on a consistent basis."

Jan 1, 1995

By M. Takebayashi, K. Takenaka, S. Matsubara, T. Yoneyama

The cathode production of Toyo Smelter and Refinery, owned by Sumitomo Metal Mining Co., Ltd. reached 450,000 tons per year in 2016 with three tank houses. Niihama tank house commenced operations in 1919 with conventional sheet cathode technology. Approximately 100 years of operation experience and the technical development enabled that the current density of Niihama tank house and the Toyo tank house #1 increased to 320 A/m2. These operation techniques were utilized at the Toyo tank house #2 which started in 2005, and its current density reached up to 350 A/m2 with permanent cathode technology. In order to achieve high current efficiency under condition of 350 A/m2 operation at Toyo tank house #2, continued efforts had been made to verticality of anodes and permanent cathodes. To improve verticality of anodes and cathodes, reduction of short circuit ratio by changing the shape of the anode, optimizing the anode pressing machine and off-line process for rectifying the distortion of permanent cathodes was carried out. In addition, concentration control of electrolyte and expansion of Ni removing ability from the electrolyte prevented passivation. Finally, more than 96% of the current efficiency was stably confirmed. INTRODUCTION Today, Toyo Smelter and Refinery of Sumitomo Metal Mining operates three tank houses in Japan, namely, Toyo tank house #1, Toyo tank house #2, and Niihama tank house with a total capacity of 450,000 metric tons of copper cathodes. Figure 1 shows the trend of cathode copper production and the current density at three tank houses over the last 10 years. Cathode production by Toyo Smelter and Refinery reached 450,000 tons per year in 2016 with three tank houses.

Jan 1, 2019

By Angela L. Paveley

Economic viability of base metal mining is complicated by a volatile market that can cause fluctuations in the growth and stability of the mining industry. Nickel is mined primarily for use in manufacturing industrial stainless steel and plating materials. It is essential that nickel production be sufficient to respond to current and future market demand. A Post-Pillar cut and fill mining complex is currently producing nickel sulfide in Northern Manitoba. From 2006 this area has shown a steady increase in the annual production, rising from 11 million pounds to 25 million pounds in 2010, and accounting for 33% of the total production for the Manitoba Operations. It is expected that fine-tuning the mining process can safely enhance ore recovery, improve production consistency, and increase economic viability of the deposit. The Post-Pillar Optimization study was initiated by the local technical and operational departments at the mine and analyzed from July 2010 to March 2011. The purpose of this study was to determine if portions of non-recoverable pillars can be slashed without jeopardizing pillar strength. This ideal case would optimize ore recovery and reduce variability in the ore mining rate. Numerical modeling and geo-mechanical material properties analyses, completed by the rock mechanics group, define the maximum drift width at 32 feet and the minimum pillar width at 18 feet. Thus, it was suggested that up to 3 feet could be slashed from two sides of the standard 24 foot pillars without damaging ground integrity. The field data collected indicates that additional ore could be recovered without compromising the safety of the workplace and the integrity of the complex. Consequently, technical and operational groups work jointly to achieve pillar optimization. Approximately 500,000 pounds of nickel was extracted from the complex via pillar optimization from July 2010 to March 2011. Economic analyses show the pillar optimization method developed for the mining complex is a proven, value-added opportunity. The mining complex remains a safe workplace and has retained ground integrity.

Nov 1, 2011

By Neri Roux, Ross Gilders, Yemi Oyediran, Leo Cheung

Quest Rare Minerals Ltd. is developing their Strange Lake B Zone REE deposit located in Northern Quebec. An extensive batch bench scale testing program was launched to investigate open circuit rougher flotation performance under different conditions. The objective of the flotation study was to demonstrate the effectiveness of rejecting gangue minerals to flotation tailings while concentrating rare earth elements as well as yttrium, zirconium, and niobium into a concentrate suitable for further hydrometallurgical processing. Mineralization of interest at Strange Lake occurs within peralkaline granite-hosted pegmatites and minor aplite. The REE and high field strength element (HFSE)-bearing phases are hosted primarily in pegmatites as relatively fine-grained phases or pseudomorphs. The gangue phases comprise of quartz, feldspar, amphibole, and pyroxene. Potential ore minerals comprise predominantly of kainosite, gerenite, gadolinite, zircon, pyrochlore, and gittinsite. These complex mineralogical characteristics increase the difficulty for processing and provide a challenge for choosing the correct reagent scheme in rougher flotation. Process options including reverse flotation to reject the gangue minerals and de-sliming prior to the direct rougher flotation were investigated. Optimization trials were conducted using various reagent regimes and under different flotation conditions. Encouraging results were found using a combination of collector reagents supplied by Cytec Canada Inc.

Jan 1, 2014

By J. Chao, C. Tan, N. Stubina

"Since J978, Falconbridge Limited has operated two electric furnaces at its nickel-copper smelter in Sudbury. As part of its S02 Abatement Program, the smelter has undergone many changes over the last seven years.This paper describes the impact of these changes on the operation of the furnaces. Some of the topics to be covered include: the installation of sidewall copper coolers; current operating conditions; and furnace heat and mass balances. HistoricalFalconbridge began smelting ores in the Sudbury area in 1930. The original smelter consisted of a 1.3 m by 3 m blast furnace and two 4 m by 6 m converters. The blast furnace was supplied with untreated mine are and molten slag/matte was discharged into a round settler.In 1933 the smelter began treating flotation concentrates. The concentrates were mixed with fine magnetic ore and flue dust, then sintered on down-draught Dwight Lloyd machines. This provided an agglomerate suitable for furnace burden which was charged to the blast furnace while still hot.Between 1930 and 1954 nickel production was increased by lengthening the 3 m furnace to 4.6 m, then to 6 m, and later by constructing additional furnaces. By 1958, the plant consisted of one 7.5 m blast furnace, a settler, and three 4 m by 9 m converters."

Jan 1, 1994

By Colin E. Dunn

Plants have a remarkable ability to select, use and store metals derived from the substrate. Each species is unique in its requirements for and tolerances to the full spectrum of chemical elements in the Periodic Table. Studies to define the chemical characteristics of common trees and shrubs of the temperate forest are providing insight to their use for exploration, i.e., biogeochemical exploration. Examples of surveys over gold deposits in British Columbia show the effectiveness of sampling various tissues from different species in a range of biogeoclimatic environments. At the Nickel Plate mine in the Montane-Spruce zone, outer bark of Lodgepole pine was effective in defining a large area of metal enrichment; at the Carolin mine in the zone of Coastal Mountain Hemlock, analysis of twigs of western hemlock and Pacific silver fir provided an exploration target considerably larger than that defined by lithogeochemistry; at the Mount Washington gold deposit in the Mountain Hemlock zone, twigs of mountain hemlock and rhododendron were used to outline the mineralization; and in the Interior Douglas-fir zone at the QR deposit analysis of Douglas-fir tops collected by helicopter provided a rapid and effective method of identifying a gold-rich area.

Jan 1, 1995

By K. Konigsman

"Representatives of various industries and the Canadian coast Guard formed a Bulk Cargoes Committee three years ago. In 1976 and 1978, I have attended the meeting which take place once per year here in Ottawa as representative of the Canadian Mineral Processors, Dave Hendricks from Granisle accepted the charge in 1977. Our Secretary, Bob Bruce, has suggested repeatedly that I report to the Membership on the deliberations to this group. Twice I found good excuses; this year I did not. I was reluctant to address you since the Committee's deliberation proceeded at a pace which might be identified as Government squared. The Committee advises a Government agency which in turn negotiates with foreign Government agencies.At the outset, I will describe the developments which led to the formation of the Committee and its purpose.The Canadian Mining Industry ships annually millions of tons of products to overseas customers; be it iron ore, coal, fertilizer, or base metal concentrates. Most loadings are in vessels of foreign registry and all will be directly affected by Canadian or International regulations of the transport of such bulk commodities. The major shipping nations are members of an Intergovernmental Maritime Consultative Organization (IMCO). This organization elaborates regulations which govern shipment of all cargo, bulk materials and concentrates included. At IMCO'S deliberations, Canada has one vote, one voice on the Consultative Committee and is represented by our Coast Guard. The Coast Guard has over the years been in contact with industries when discussions concerned shipment of bulk cargoes. In the early sixties, a ""Concentrate Committee"" did exist. It consisted of metallurgists from a number of mining companies and Government representatives. This committee was instrumental in the development of what became known as the ""Concentrate Code"", legislation which has evolved into the Canadian Bulk Cargoes Code as it is known today. The concepts of the flow moisture point and transportable moisture limit originated from its work. Incidentally, both criteria are widely accepted and utilized world-wide. The Concentrate Committee faded away once the Concentrate Code has been adopted."

Jan 1, 1979