Search Documents

By O. Hall

DISCUSSION AT QUEBEC MEETING MR. A. V. CORLETT: With drill holes radiating from a common point, is loading carried to the collars, and do you undertake to distribute the powder evenly? MR. R. V. PORRITT: When the collars of the holes, particularly the diamond-drill holes, are close together, two out of three holes are loaded only to within six or seven feet of the collars, and the intervening holes are loaded close to the collars. When the collars are farther apart, the holes are loaded close to the collars. No spacers are used, and the holes are filled solid with powder, this applying particularly to the diamond-drill holes, except, of course, where the collars are close together and some holes are not loaded close to the collars. MR. J. G. L. McCREA: I would like to enquire in respect to the various efforts made to reduce the cost of diamond drilling to the lowest point, what is. the relative cost of the solid bit to the standard bit? It would seem that the solid bit has the higher cost. MR. PORRITT: The non-coring or solid bit gives a slightly lower diamond cost than the coring bit. With the coring bit, the greatest diamond loss is on the inside stones, apparently due partly to vibration, but mainly to the core blocking against these stones. This condition, of course, does not apply with the non-coring bit. Our experience is that the non-coring bit, which drills out a much greater area, has a diamond consumption slightly less than the coring bit. The non-coring bit is sturdier, and is far less liable to damage in starting holes and in drilling through cracked or broken ground.

Jan 1, 1939

By S. A. Bunk, E. C. Eccleston, J. J. Amsden

Fluidized bed technology has been widely applied to mineral and metallurgical processes. Over the years, modeling of fluidization technology has progressed to a level at which basic design parameters can usually be defined based on empirical correlations. In addition, scale-up considerations have become better understood, and significant advances have been made in the area of computer simulation. Despite these advances, fluidization is a complex phenomenon, and modeling tools remain limited in their ability to simultaneously model both fluidization and chemical process parameters. As a result, almost all mineral and metallurgical applications of fluidized bed technology require pilot testing prior commercial scale design. This paper outlines pilot plant testing requirements and process development considerations for development of low technical risk commercial designs.

Jan 1, 2011

By L. Henry Smith, David C. Arthur

"The Williams Mine is Canada’s largest gold producer, with annual production of 450 000ounces from 2 300 000 tonnes of ore. Highly mechanized and automated underground mining practices are employed in order to achieve and maintain high levels of productivity and minimize costs.The mine ventilation system is modified to include a new vent raise and variable pitchvane-axial fan. This addition allows several fan installations underground to be decommissioned. A substantial net savings in installed horse power is achieved.Heating costs associated with under-ground ventilation air are a significant portion of mine operating costs. Air heating costs are substantially reduced by recovering heat from upcast exhaust air, minewater and compressor cooling circuits. This waste heat is used to supplement propane fired air heating systems for underground ventilation air. An additional benefit is the availability of a heat sink for summer cooling of the compressors.System design, energy savings data and payback calculations are presented."

Jan 1, 1996

By A. Atef

Vulnerability is a measure of the extent to which a community, structure, services or geographic area is likely to be damaged or disrupted by the impact of particular hazard. Current asset management practices focuses on studying factors that affect performance of isolated infrastructure networks and model a set of actions to control the expected performance of these networks. This approach ignores the underlying spatial and functional interdependencies among these infrastructure networks and their vulnerability. The purpose of this paper is to introduce a new method that recognizes the effect of spatial and functional interdependencies on vulnerability rating of water, sewer and road networks. The proposed method consists of: 1) risk assessment model, 2) interdependency assessment model and 3) vulnerability assessment model. The risk model is composed of two modules: 1) water and sewer risk module and 2) road infrastructure module. The water and sewer risk module will cluster these assets into three risk categories based on environmental, social, operational and economical factors. The road infrastructure module will cluster road assets into three risk categories by using rational factorial technique based on road type, serviceability index, traffic load, and freeze and thaw index. The interdependency model will deploy the risk ranking to perform geospatial analysis in ArcGIS which results in determining the interdependent layers of waters, sewers and roads. The vulnerability model will deploy fuzzy neural networks technique to determine the vulnerability rating based on spatial and functional interdependencies. The fuzzy neural networks are utilized to overcome the lack of historical data and incorporate experts? preferences for establishing the knowledge base for vulnerability assessment. The expected contribution of this framework is to aid decision makers in understanding the interdependencies between civil infrastructure assets and to which extent such interdependencies can compromise assets performance.

Aug 1, 2013

By D. Letzig

Wrought magnesium alloys are of special interest as lightweight structural components as a result of their more homogeneous microstructures and improved mechanical properties compared to cast components. Extrusion as a shaping technology offers the possibility to produce a wide variety of magnesium alloy profiles. In this contribution we describe the role of extrusion parameters such as extrusion speed, ratio and temperature as well as the type of extrusion process on the microstructural development of AZ-series magnesium alloys and the resulting mechanical properties. The effect of microstructure on the tensile/compression deformation behavior of the alloys has also been investigated. Aspects of process optimization designed to overcome technical and economic limitations and thus establish magnesium alloy profiles for industrial applications will also be discussed.

Jan 1, 2006

By Bradford P. Simser

The theoretical capacity of various ground support components can be misleading, especially in bursting ground where the failure mode is often in the retainment system. Wire mesh screen seams often peel open rather than breaking the wire strands, fractured rock often un-ravels around the bolts rather than breaking the bars. If a weak link(s) in the system fails prematurely, then the potential capacity of the system may never be fully realized. Underground observations are used to show how some support systems behave in the field. Various combinations of wire mesh screen with friction bolts, rebar, modified conebolts, cablebolts, shotcrete and mechanical rockbolts are considered. A short case history is used to contrast the performance of ?just-intime? development in a high stress faulted area versus a tunnel subjected to multiple stress changes in a similar environment. The latter proved to be a serious ground support problem when the well developed fracture zone around the opening was subjected to dynamic loading from a large seismic event causing a severe rockburst. In such cases an improved mining strategy may be more relevant than higher capacity support systems.

Feb 1, 2008

By Greg Yuriy

This paper discusses research carried out by the Laurentian University Mining Automation Laboratory (LUMAL) in the field of discrete-event simulation of mine equipment systems and reliability assessment of these machinery using genetic algorithms. The AutoMod simulation package, from Brooks-PRI Automation Inc., is used in this research. It is a 3-D discrete-event simulation/animation software tool for creating realistic depictions of manufacturing and materials handling systems. Discrete-event simulation involves modeling of real-life systems based on variables and events which occur or change at distinct points in time. In our case, a two level, multi-drift sublevel stoping model was created in AutoMod for the simulation of the equipment fleet employed in the development cycle (drilling, explosives loading, blasting, materials hauling, ground support) of a typical underground mine in the nickel mining region of Sudbury in Ontario, Canada. The equipment primarily considered in the simulation is Load-Haul-Dump (LHD) vehicles (scooptrams), drills, explosives-loaders and roof bolters. The purpose of the simulation study is to assess the impact of equipment failures to mine?s production throughput. In more detail, using Mean Time Between Failures (MTBF) data of scooptrams derived from a reliability assessment model based on genetic algorithms, LHD failures are incorporated into the simulation model. These failures cause production interruptions to the development cycle and consequently loss of hauling capacity. This paper will indicate the significance of equipment failures to a mine?s production and suggest a methodology based on the combination of discrete-event simulation and a predictive reliability assessment model using genetic algorithms for the study and analysis of mine equipment systems.

May 1, 2003

By Curtiss O. Ehrsam, M. Naseem Mian

Alaska’s Red Dog Mine is strengthening its position within Cominco’s “Vision 2000”strategic plan by continually improving quality and quantity of production while reducing costs. Red Dog has evolved into a stable and mature operation, after six years of milling experience. A high grade, partially oxidized orebody in the severe Arctic environment, along with competing producers in a volatile metals market, are the continuing challenges facing Red Dog. The Red Dog Mine is striving to meet these challenges with emphasis on operator training combined with creative systems development and increased production. This paper describes developments in operations along with future plans.

Jan 1, 1996

By SangHyeok Han

Selecting the best possible cranes and identifying spatial conflict-free locations on sites can result in productivity and safety improvements for large-scale industrial construction projects. In the current practice, experienced lift engineers select cranes based on the heaviest lift and/or the largest lifting radius of the identified crane. This practice is relatively time-consuming, and optimization of the crane?s use and location is also difficult. There are many factors which need to be considered during the crane selection process, a reality which further complicates the process. This paper presents a framework which aims at developing a decision support system to enhance the crane selection process and collision-free path planning for large-scale construction projects. This paper utilizes an innovative crane selection matrix in order to establish a process for optimized crane selection for construction projects. The study considers more than 40 different factors in order to reduce time and improve safety for crane operations. Following finalization of crane type (mobile crane versus tower crane), a visualization model to simulate crane operation and identify collision-free crane operation paths is proposed. This process can assist project managers to plan the lifting process more effectively and efficiently. A case study-based approach was utilized to demonstrate the proposed methodology. The methodology was tested in the planning and construction process for boiler house structures in Mannheim, Germany. The project entailed numerous challenges: one of the major tasks was to lift a 102-ton load on the top of the boiler structure through crane collaboration; space limitations on site also presented several challenges related to crane selection, location, and operation processes. Based on the project constraints, the proposed crane selection framework, and the visualization models, two tower cranes were selected and successfully implemented in the case study.

Aug 1, 2013

By N. Depountis, Th. Rondoyanni, N. Sabtakakis, K. Kavoura, G. Tsiambaos

"Some typical landslide phenomena in Western Greece, in terms of the geological composition and structure of the affected materials, induced by heavy rainfalls are thoroughly studied and analyzed. The studied cases involved composite landslides on Flysch and Neogene weak rock materials that constitute the most critical landslide prone geological formations in Greece. The studied cases named Platanos, Platanitis and Karya include representative landslide sites as regards to the geological composition and structure of the displaced formations. Thus: (a) flysch formation includes different lithological units as shales, marls, siltstones, sandstones and conglomerates and is closely related to the Alpine orogenesis, suffering intense past tectonic movements and (b) the Plio-Pleistocene sediments include clayey marls, marlstones and siltstones. The investigated landslides , affecting mainly transportation routes, are closely related to heavy rainfalls induced by extreme meteorological events and are controlled by active fault tectonics. Long term movement monitoring using borehole inclinometers and surface benchmarks showed that landslides control was effective only when the proper stabilization measures were taken.INTRODUCTIONLandslides represent a major threat to human life, property, infrastructure and natural environment in most regions of the world. They are recognized by the scientific and politic authorities as having a major socio-economic impact and they represent a significant hazard for the population and the properties in particular locations. Landslide hazard expressed as the probability of occurrence within a reference time period and is a function of the spatial and temporal probability (Varnes, 1984; Guzzetti et al. 1999; Lee and Jones, 2004). The spatial probability of landslide initiation (susceptibility) is mainly related to static causal factors (slope inclination, material properties, etc.), while temporal probability is mainly related to dynamic causal factors such as rain input, increased groundwater levels and drainage, earthquakes, etc. (Van Westen et al. 2005)."

Jan 1, 2015

By W. Schubert, N. Radoncic

"The term “squeezing” is frequently used, although it is ill defined. Definitions like “large and long lasting displacements” raise the questions about the threshold values for the magnitude and duration of displacements. Large displacements during tunnelling frequently are observed in fault zones with high overburden. Whether this causes problems very much depends on the design approach used. On the one hand, the magnitude of expected displacements has to be predicted prior to excavation to provide for enough allowance for the displacements without violating the clearance profile. On the other hand, the support characteristics must be compatible with the expected imposed strains. As the magnitude of the displacements and thus the strains in the support depend on the support capacity and its characteristic (yielding potential), only well engineered systems will be successful.Experience in Alpine tunnels over the last decades has shown that closed shotcrete linings can sustain a strain of approximately 0.8% to 1% without failure. Any strain above this value inevitably leads to failure of the lining, and thus a loss of resistance, causing additional displacements. Based on a large number of simulations, a criterion for a critical overburden depth up to which closed linings can be used has been developed. Traditionally open gaps in the shotcrete linings have been used to allow for larger strains. To enhance the efficiency of the linings, yielding elements have been developed, which are integrated in the shotcrete lining, allowing large strains and controlled development of support resistance (Figure 2). When designing such yielding support systems, the development of the displacements, as well as the rheological behaviour of the supports must be considered. As the development of displacements to a large extent depends on the face advance, also the advance rate has to be considered, to be able to compare the time-dependent strength of the lining to the stresses developing as a result of the imposed strains. Another issue is the compatibility of the rock bolts with the large strains. With standard grouted bolts, there is a potential that the “fresh” grout is sheared due to the initially large strain rates. Special rib designs of the bolts allow for a higher strain tolerance.For successful tunnelling through fault zones quality monitoring and up-to-date data evaluation is of crucial importance. With advanced evaluation tools, changes in the ground conditions ahead of the face can be reliably predicted. With the help of empirical relations, the development of the displacements for different advance rates and supports can be predicted, allowing for the determination of the required overexcavation.The paper presents a review of the development of ductile elements, methods of analysis, and monitoring data interpretation."

Jan 1, 2015

By D. G. Cerigo, D. M. Bryce, P. H. Jennings

This paper summarizes the results of an experimental and economic study undertaken to evaluate the feasibility of treating an oxidized orebody of about 10 million tons, grading about 0.75 per cent copper, by agitation leaching and by percolation leaching.

Jan 1, 1968

By M. Kellner

Due to continuously growing resource demands and increasing requirements for sustainability, safety and environmental protection on the other hand, the mining industry is being subjected to these additional requirements. Over the past few decades progress has been made in all topics. In 1987, the United Nations published the following in the Brundtland Report: ?development that meets the needs of the present without compromising the ability of future generations to meet their own needs.?[5] The term ?Blue Mining? means to work sustainably, economically, ecologically, and efficiently while also improving ergonomics, for example by increasing automation. An example of how mining can actively be involved in energy management will be shown. Initial evaluations of underground cavitites were done for purpose of energy storage. The planning and construction of underground pump storage plants both in active and inactive mining operations was also investigated.

Aug 1, 2013

By J. D. Jones

The geographic occurrence of economic mineral deposits presents a variety of problems in modern tailings disposal operations. This paper presents case histories in several sectors of the mineral industry as well as the several stages of operations planning required for new designs, system expansion, reactivation of abandoned systems and upgrading to present environmental standards.

Jan 1, 1978

By Ralph L. Rutherford

Introduction During the past twenty-five years we have seen considerable exploration for oil on the plains of southern and east-central Alberta. This exploration has to some extent gone on in cycles, with periodic starts, stops, and occasionally some reversals. Each major attempt is usually supplemented by the application of some new method of exploration and, following each period of exploration, drilling tests are made. Whereas oil-bearing horizons are the ultimate objective of these explorations, the preliminary investigation frequently aims at a discovery of structure based on the long accepted belief that accumulations of oil and gas are to a marked degree structurally controlled. At the inception of this general exploration for oil, it was natural that attention should be directed to areas where there was surface evidence of deformation of the underlying strata, but, as the programme progressed, it was found that these surface manifestations of structure were often deceptive when attempts were made to project them to depth, to involve the deeper strata. Drilling of test wells was the only satisfactory method of obtaining exact information.

Jan 1, 1946

By W. L. Uglow

In recent years, the microscope has come to be recognized as a valuable aid to engineers whose business is the discovery, development, concentration or reduction of metallic ores. In many of the large treatment plants microscopical research has already an important status; and in the hands of efficient operators the microscope has indicated methods of solving ore problems resulting in the saving of thousands of dollars that otherwise might have been lost in tailings, or expended in freight rates or smelter charges. Failure to procure all the information that the microscope can supply concerning the physical and mineralogical characteristics of complex ores has in many cases led to the construction of unsuitable concentrators, just as the failure to investigate in detail the geological conditions of an ore deposit has often results in the squandering of money on shaft sinking, and mechanical installations which subsequent development of the deposit failed to justify. The great progress recently made in the selective separation of minerals by means of the various processes of flotation and leaching brings strongly to our attention, the scope of the field in which microscopical methods may be advantageously employed. The microscope enables one to observe the minute details of rock, ore, gangue, concentrate, tailing, matte, slag and metal, that are invisible to the naked eye. Furthermore, the technique of microscopal research has been so highly developed that a microscopist can not only observe, but deter-mine the compositions and measure the diameters of the mineral constituents in the ore to be treated. Magnifications of these constituents up to 3,000 diameters may be produced by the proper combination of eyepiece, objective, and projection apparatus, and the images thus viewed may be photographed through the microscope, and permanent records made of them.

Jan 1, 1924

The reliability of mining systems is generally low due to their harsh working conditions. Currently, efforts for improving mining system reliability are often made in isolation. This practice could substantially limit the effectiveness of the efforts on overall reliability improvement of the mining system. To enhance the overall reliability of mining systems, an integrated improvement approach is necessary. In this paper, we developed a framework for integrated mining system reliability improvement to address this issue. In this framework, there are five major components including data integration, business process integration, hardware integration, software integration, and analysis/decision integration, but we only focus on the integrated reliability analysis which is important to the analysis/decision integration. The reliability analysis considers the interactions between machines, and the impacts of design, operation, maintenance, automation and working environment on the overall system reliability. These multiple interactions present a big challenge to accurate reliability prediction. In this paper, we for the first time systematically investigated integrated reliability analysis approaches for dealing with this challenge using novel models and methods, including covariate hazard models, intelligent reliability prediction approach, and complex system modeling methods. While these models and methods have found some successful applications in other industries, they in general have not been effectively used for the reliability analysis of mining systems. Our study results show that the system integration approach is applicable to mining systems and can be used for developing a computer aided integration system for the implementation of the integrated reliability improvement approach.

Aug 1, 2013

By G. Lafont

Aug 1, 2013

By Karen M. Moffitt

Developments in mining methods and rates have led to an increase in the frequency and size of waste dump failures that have not been adequately predicted or explained in terms of conventional slope stability analysis. Monitoring data and visual observations suggest a unique mode of failure responsible for large runout events. A numerical model has been developed to capture commonly observed patterns of deformation, and investigate the formation of the ensuing failure mechanism. The analyses have yielded a good correlation with observed field behaviour and have provided significant insight into the coincident stresses and deformations within the dump. Results indicate that while creep effects in the waste dump could have a significant effect on the magnitudes of displacement, the overall dump stability is governed by the strength of the foundation soils underlying the toe region. Consideration of both the stress and velocity fields leads to factors of safety for various dump heights and foundation slopes that are considerably less than predicted from limit equilibrium analysis. The results suggest that conventional limit equilibrium analysis techniques may not be adequate when assessing the stability and design of waste dumps on steeply sloping terrain.

May 1, 2001

By James A. Finch, Yue Hua Tan, Wei Zhang

"The paper is part of our study of the frother structure-property relationship using bubble rise velocity. Single bubble rise velocity profiles were determined in a 350 cm column for surfactants from the polypropylene glycol (PPG) family. Using velocity at 300 cm, the concentration to reach minimum velocity (CMV) is determined. The CMV is shown to decrease as alkyl chain length (n, number of carbons) increases and as the number of propylene oxide groups (m) increases. Linear correlations log CMV vs. n and m were observed. Taking literature data for critical coalescence concentration (CCC), linear log CMV vs. log CCC correlations were also noted. Mechanisms are briefly discussed, and prediction of CCC made for a commercial polypropylene glycol.INTRODUCTIONAs one of the great enabling technologies of the 20th century, froth flotation is a highly versatile method for physically separating minerals by exploiting differences in wettability (hydrophobicity). Over the last century, flotation reagents have undergone significant developments (Khoshdast and Sam, 2011). One important group of reagents is frothers which are used to reduce bubble size, slow bubble rise velocity and help stabilize froth (Klimpel and Isherwood, 1991).Frothers, originally derived from natural sources (e.g., pine oil and cresylic acid), are largely replaced today by synthetic products which provide more consistent properties. Polyglycols, based on PEO (polyethylene oxide), PPO (polypropylene oxide), or PBO (polybutylene oxide) groups, were first described by Leja and Nixon (1957) and have attracted wide use since then (Farrokhpay 2011). The chemical structure of polyglycols can be represented by a general formula: R(X)mOH, where R = H, or CnH2n+1 and X stands for EO (-C2H4O-), PO (-C3H6O-), or BO (-C4H8O-). The polypropylene glycol ethers (CnH2n+1(PO)mOH) are the most common of these reagents (Pugh, 2007) and the focus of this study.In general, the chemical structure of frother molecules comprises two parts, a non-polar hydrophobic hydrocarbon (alkyl: CnH2n+1) chain and a polar hydrophilic head. By introducing the ether -Olinkage, which acts as another polar site, the propoxy group (-OC3H6-) in the structure makes the frother readily soluble in water (Somasundaran and Wang, 2006), facilitating the industrial use of these frothers. Available as by-products, Dow Chemicals introduced as series of polyglycols, e.g., Dowfroth (DF) 200, 250, 263, and 1012, the most familiar being DF250 (CH3(PO)4OH), a polypropylene glycol methyl ether. While no longer available from Dow, these and other polyglycols are still widely used."

Jan 1, 2016