Search Documents

By Cees van Rhee, Rudy Helmons

INTRODUCTION Seafloor Massive Sulphides are typically found near the oceanic ridges at larger water depths (>1km). The physical properties of SMS, as shown in table 1, are comparable to the properties of weak rock. One of the technical challenges to enable extraction from these locations is the cutting or excavation process. Experiments have shown that the energy needed to excavate the material may increase with water depth (Alvarez Grima et al. 2015). Besides that, it is demonstrated that rock that fails brittle in atmospheric conditions can fail more or less in a plastic fashion when present in a high pressure environment, as would be the case at large water depths. The goal of this research is to identify the physics of the cutting process and to develop this into a model in which the effect of hydrostatic and pore pressures is included. The cutting of rock is initiated by pressing a tool into the rock. As a result, at the tip of the tool a high compressive pressure occurs, which leads to the formation of a crushed zone. Depending on the shape of the tool and the cutting depth, shear failures might emanate from the crushed zone, which will eventually expand as tensile fractures that can reach to the free rock surface. Through this process intact rock will be disintegrated to a granular medium. For an overview of the process (figure 1). Additionally, the presence of water in the pores of and surrounding the rock influences the cutting process through drainage effects. The most relevant effects are weakening when compaction and strengthening when dilation occurs in shearing and tension. Deformation of the rock causes the pore volume to change, resulting in a under or over pressure. As a result, the pore fluid needs to flow. The magnitude of the potential under pressure is limited through cavitation of the pore fluid, limiting further reduction of the pore pressure (figure 2). The drainage effects cause the rock cutting process in a submerged environment to show a stronger dependency of both the hydrostatic pressure as well as the deformation rate (figure 3).

Jan 1, 2018

By Benoît Waquet

In a context of scarce mineral resources, coupled with an increasing global demand in metals due to the exponential growth of newly industrialized countries, the mining industry will inevitably have to deal with tomorrow?s resources: underwater deposits. Three types of offshore deposits are known to date: polymetallic nodules, cobalt-rich crusts and hydrothermal sulphides. The latter, regarding the political-economic context, is now considered most likely to be exploited in a near future. Operating a mine critically requires accurate knowledge on geotechnical properties of the ore. A question is thus to be asked: Is there a particular spatial organization of geotechnical properties in a hydrothermal sulfide mound? In the present study, geotechnical properties have been measured for 29 sulfide samples of known origin, completed by 14 measurements on Western Pacific specimens from Yamazaki et al. (1990) and Yamazaki and Park (2003). From these geotechnical data on 43 sulfide samples, we can provide some answers to this question above, crucial for future exploitation of underwater mines.

Jan 1, 2010

By Allan Spencer

In March 2007, Nautilus Minerals Inc. announced that they had commenced their 2007 exploration and development program with the mobilization of the Research Vessel Wave Mercury and the Survey Vessel Aquila onsite Papua New Guinea.

By Satya Nandan

The International Seabed Authority is currently considering regulations for prospecting and exploration for polymetallic sulphides and cobalt rich crusts. The deposits of these two types of minerals are very different from polymetallic nodules for which the Authority has already adopted regulations in 2000. The presentation will discuss the nature of the deposits, the inadequacy of information and data concerning these deposits and their environment, as well as the problems of defining the method of allocation and the size of the areas to be licensed for exploration, and those to be retained for exploitation; the current status of the draft regulations being considered by the Council of the Authority.

Aug 24, 2006

By Akira Usui, James R. Hein, Rachel Dunham

Ferromanganese crusts are found on most hard-rock substrates in the deep ocean (800-3,000 m). Their distributions on seamounts are complex and controlled by a wide-variety of factors including seamount morphology, current patterns, mass wasting, substrate rock type and age, subsidence history, and others. However, the development of this potential resource ultimately depends on this distribution, as well as on the small-scale topography, grade, and tonnage. The parameters that will ultimately be used to define a mine site are unknown, but reasonable assumptions based on 25 years of data collection can be used to bracket likely permissive characteristics.

By Luana Karvel, Lars Kullerud, Morten Sørensen, Øystein Halvorsen, Øivind Lønne, Elaine Baker, Tina Schoolmeester, Joan Fabres, Yannick Beaudoin

The UNEP Shelf Programme (USP) is the access point for a collaboration of international organizations with expertise in marine geoscience and maritime law. It was established in response to a United Nations resolution, stating that the United Nations Environment Programme (UNEP), working through the Global Resource Information Database (GRID) system, should work in conjunction with Intergovernmental Oceanographic Commission of UNESCO (IOC) and the International Hydrographic Organization, to assist coastal States, and in particular developing States and small island developing States (SIDS) with submissions to establish the outer limits of their continental shelf under Article 76 of the United Nations Convention on the Law of the Sea (UNCLOS).

By Sally Philpot, Siân E. Boyd, Hubert L. Rees, Emma Bee, Carla Houghton, Ceri James, Silvana N. R. Birchenough, S. Limpenny David, A. Coggan1 Roger, Koen Vanstaen

Every year approximately 22 million tonnes of marine sand and gravel are dredged form British waters. The eastern English Channel (EEC) contains substantial reserves, a proportion of which have been identified by the aggregates industry for potential future exploitation. The main aim of this study is to produce broadscale marine habitat maps of the EEC area. The UK aggregates industry has formed a consortium of representatives (the eastern English Channel Association), and have sponsored an initial baseline survey and follow-up sampling programmes as part of a Regional Environmental Assessment (REA) covering a patchwork of aggregate prospecting areas. To complement this effort, a large-scale geophysical survey was conducted in 2005 to place the REA in a wider spatial context and, thereby, to help assess the environmental significance of any future impacts arising from commercial aggregate extraction over the broader region of the EEC.

Sep 24, 2006

By H. Shimoda, K. Tamaki, K. Iizasa, M. Watanabe, K. Okamura

Modern Kuroko-type deposits occur in submarine calderas of island-arc fronts and back-arc rifts in Japan. They occur primarily on or adjacent to caldera boundary faults. Hydrothermal sulfides in the Myojinsho submarine caldera are one of Kuroko-type deposits, but their occurrence is different from other deposits found within the area 200 km2 around the Quaternary volcanic front of Izu-Ogasawara arc.

Aug 24, 2006

By Wonn Soh

As for Earth, where human beings live, approximately 70 % of its surface is covered by oceans. Today, advanced technology has led us to understanding the abyssal ocean floor through the use of submersibles and ROVs (remotely operated vehicles) for the last 30 years. Furthermore, the oceanic crust beneath the abyssal floor still remains an unexplored scientific frontier due to the lack of a direct approach. Exploration of this frontier is required to enhance our understanding of the mechanism of the M.8 class plate-subduction-type earthquake, of generation of the big tsunami, that caused the disaster, and of the paleo-global environmental change as well as of the origin of life as viewed in deep water thermal vents.

By In Kwon Um

The XRF Core-Scanner system performs non-destructive analysis of elements from Mg to U, in concentrations of ppm levels on split cores with digital images. Using the AVAATECH XRF Corescanner system, we conducted high resolution element analysis of deep sea sediment cores from Clarion-Clipperton fracture zone of the northeastern Pacific to reveal recent environmental changes. Comparison of data estimated by the XRF core scanner with ICP-AES showed relatively weak correlation coefficients except Mn contents. Down-core variations of most elements seem to be matched with each other and reflect changes of sediment colors. Especially Mn/Al ratio significantly change at distinct color boundaries. The variations of Mn/Al ratio with sediment colors are suggestive of changes in redox condition and further divided into two types probably affected by activities of benthic organisms. Be isotope age datings of select core (BC08-02-13) indicate that the color boundaries are approximately coincident with late Pliocene and Pleostocene also early Pliocene and late Pliocene boundary. Keywords: XRF core scanner, High resolution, C-C zone

Jan 1, 2011

By Winston Rocher Anda

Traditionally, mining activities have been developed in firm land, but technological advances and human needs have opened in the last year?s new opportunities in the maritime field. This has happened not only in the oil or hydrocarbons industries, but also in relation to the exploration or exploitation of other minerals, metallic and non-metallic. This has forced several countries to complement or create legal rules that make possible its own development and the International Law, through the United Nations Convention on the Law of the Sea, to regulate this activity in the space of its own, the calling area. Chile, as country with a long experience in mining and great advances in large deposits exploitation, possesses a special juridical frame that regulates this economic activity according if it is the geographical or territorial area in which is realizes, and it has been complemented lately with the international normative.

Jan 1, 2011

By Cheng Xiangzhou

The China's Pioneer area includes two parts. The topography in the western part is very different from that in the eastern one. The distribution of the manganese nodules in these two regions differs correspondingly China Ocean Mineral Resources Research and Development Association (COMRA) will take appropriate measures so that the next development will be adapted to the features of its potential minable area.

Jan 1, 1996

By Ki-Hyune Kim

The Korea Ocean Research and Development Institute conducted its first exploration for deepsea mineral resources in 1983, and began a systematic deepsea prospecting in 1989 among Micronesian islands and in central and eastern parts of Carion-Clipperton fracture zones of eastern Pacific. With the arrival of R/V Onnuri in 1992, KORDI commenced a full-scale national program for nodule exploration. The total area surveyed by KORDI covers more than 1,500,000 km2. At the end of 1993, based on the collected data, Korea designated 300,000 km2 in the Clarion-Clipperton fracture zone as prospective mining area for manganese nodules, and accordingly, the government of Korea submitted the application in January of 1994 to the United Nations for registration as a pioneer investor and for the allocation of a pioneer area. This application was approved by the General Committee of the Preparatory Commission in August 1994. As a result, Korea became the 7m pioneer investor under the United Nations Convention on the Law of the Sea. KORDI is now carrying out detailed exploration survey and environmental studies in the registered area to fulfill required obligations to UN, and Korea will continue exploring the last frontier on earth. It is KORDI's unshaken calling to be successful in exploiting deepsea resources to provide our nation resources it lacks. It is not only a challenge to explore deepsea, but it is also our national mission to explore and succeed in our endeavor for future generation.

Jan 1, 2011

By G. Rehder, C. Hensen, P. Linke, J. Bialas, M. Haeckel, W. Weinrebe, K. Wallmann

Research on marine gas hydrate and the methane cycle has a tradition at IFM-GEOMAR. In summer 1996 during a cruise with RV SONNE offshore Oregon (USA) scientists of the former GEOMAR recovered the largest amount of gas hydrate from the seafloor. This discovery stimulated research on marine gas hydrates in Germany and induced funding of scientific programs such as LOTUS and OMEGA with numerous innovative technologies within the special program GEOTECHNOLOGIEN of BMBF and DFG. The primary objectives of ongoing and future research are to achieve a comprehensive knowledge of: • gas hydrate distribution and quantity; • variation and regulation of gas hydrate formation and dissociation as well as of the related fluid flow; • functioning of chemosynthetic communities in methane oxidation, carbonate precipitation and methanotrophy as biological barrier against methane emission and • delineating the escape routes of methane to the hydrosphere and atmosphere.

Aug 24, 2006

By Mike Woodborne

The marine diamond industry off south-western Africa is maturing rapidly. Some of the larger explorers have reached an advanced stage in their resource development and new mining operations have been started in the last year. Most of the major exploration, mining and marine engineering companies have offices in Cape Town. As a result of the increased activity and experiences to date, new approaches to marine diamond exploration and mining are now evolving. Primary factors contributing the new approaches are namely 1) the concentration of expertise in a localised area 2) the significant increase in the base of available exploration and production results and 3) parallel advances in the marine engineering design and geophysical survey equipment. The sea floor geology and setting of the marine diamond exploration areas is now better understood. Consequently the strategy for exploration and the selection of appropriate survey equipment is improved. Due to new equipment developments, different exploration alternatives now exist, depending on the programme objectives. Significant advances have also been made in the data processing and modelling undertaken to assist in the identification and targeting of potentially diamondiferous prospecting features. Similarly, the design of appropriate prospecting tools and programmes has also been improved. Following exposure to the requirements of the marine diamond industry, the design engineering and operating companies have responded with innovative designs for new prospecting tools. In recent years the availability of relevant information on marine diamond prospecting and production has increased. As a result, there is now sufficient basis for the construction of meaningful financial valuation models that can be effectively used to control and guide the exploration projects, to the benefit of both the explorer and the investor.

Jan 1, 1998

By Robert Corcoran, Piotr Jasiobedzki, Roy Jakola, Michael Jenkin

Vast mineral resources of copper, zinc, cobalt and gold have been identified off the coast of Papua New Guinea at depths exceeding 2,000 meters. Accessing them in a cost effective manner and without destroying the marine habitat requires overcoming numerous technical and operational challenges. Although there are a number of deep-sea mining operations underway worldwide, the depths encountered are significantly less than will be required to mine these ore deposits. To date, only the oil industry has developed technologies for successfully accessing reserves at depths of 3,000m.

By Alexander Malahoff

With its new continental shelf beyond the exclusive economic zone, New Zealand is a country with just 4% of its territory above water. The other 96% is submerged. New Zealand's marine territory covers an area about three-quarters the size of Australia. This territory includes large portions of the Gondwana continent from which NZ separated more than 80 million years ago. This underwater land mass extends from the shores of New Zealand to a water depth of more than 5,000 m, is largely unexplored and is almost certainly the site of many large, untapped oil, gas and mineral deposits. Underwater oil and gas drilling is now a universal activity. Underwater mining is in its infancy and will become a major activity in the future, contributing greatly to the New Zealand economy. New hydrocarbon deposits will undoubtedly be discovered under the ocean floor in regions such as the Great South Basin located off Canterbury and Otago. Mineral deposits are also undoubtedly located within the oceanic crust of this underwater NZ continent. These are as yet unknown and unexplored. The oceanic crust north of the North Island is currently being extended through the subduction of the Pacific plate into the Tonga Kermadec trench and through the growth of a line of submarine volcanoes extending north to Tonga. Active submarine volcanism has led to the growth of ocean floor mineral deposits consisting of polymetallic sulphides with iron, copper, zinc and lesser gold, silver and other metals.

Jan 1, 2011

By Justin C. I. Baulch, Robina Sharpe, Steven J. Downey, John P. Feenan, Kate M. Perrin

Since becoming a public company in October 2005, Neptune Minerals has continued to advance its primary aims. Major achievements in the last year have been: • Successful completion of two simultaneous New Zealand exploration programs, Kermadec 2007 (K-07) and Colville-Monowai 2007 (CM-07); • New discovery of an inactive SMS field on the Rumble II West seamount; • Focused exploration license applications over quality areas of known SMS mineralization in arc and back-arc settings in Japan, Vanuatu, Papua New Guinea (PNG), Northern Marianas Islands (CNMI), Palau, and Italy; • Granting of licenses covering some 200,326 km2 of arc and back-arc within the EEZ of PNG and the Federated States of Micronesia (FSM); • Targeting of an additional mineralization style with extensive applications in PNG covering Conical Seamount-style Au-rich epithermal mineralization; • Welcoming Newmont Mining, one of the World’s largest mining companies, as a major shareholder; • Commissioning a scoping study to investigate options for mining and processing of SMS; Marine Minerals of the Pacific: Science, Economics and the Environment UMI2007 · The University of Tokyo, Japan Baulch 2 37th Underwater Mining Institute · 15-20 October 2007 • Invitation to contribute to, and participate in, the Meteor M73/2 Tyrrhenian Sea research program. The Company has granted exploration licenses covering 263,000 km2 in New Zealand, FSM and PNG, and a further 362,000 km2 under application in Japan, PNG, Vanuatu, Northern Mariana Islands, Palau and Italy.

By P. C. Hollick

Two marine diamond deposits on concession 2b off Namaqualand along the South African Coast, have been systematically mined over the past year by the mv Moonstar. The two deposits, Smith?s Ulcer and Wedge Point Basin, are comparable in morphology, straddled the same water depths and have similar geology yet have given very different recoveries when compared to their respective grade models. These differences are best ascribed to the different style of mineralisation observed within the two deposits which has been directly controlled by the bedrock morphology. The smith?s Ulcer deposit has been formed in a metagreywacke bedrock displaying a strong north-south trending foliation which dips steeply to the west. Consequently the mineralisation is confined to narrow north-south linear trends with limited lateral extent (less than 5m) making extraction extremely difficult and somewhat variable. RE factors (recovered grade versus estimated grade) for this deposit range from 0.5 to 1.1. The Wedge Point Basin deposit is formed in a micaceous metaquartzite with a conjugate southwest northwest joint set, the southwest lineation being the more prominent, and structural foliation dipping gently to the west. The resultant style of mineralisation is confined to basinal features defined by topographical lows and is fairly lateral in extent (in order of 50m). Extraction of the mineralisation from this deposit is less arduous with recoveries more uniform, RE factors are frequently in the range 2 - 3. This style of mineralisation is more in line with what is to be expected from marine alluvial deposits, the nugget effect of diamond concentration being responsible for the high RE factor. The long narrow linear trends observed in Smith?s Ulcer demonstrably require a specialised approach in successfully sampling, modeling and ultimately mining.

Jan 1, 1998

By U. Schwarz-Schampera, P. Stoffers

The main characteristics of the 2545 km Tonga-Kermadec subduction system are the subduction of the Pacific Plate and its sedimentary cover in the Tonga-Kermadec trench and the extension and rifting of the lithosphere behind the active island arc in the Lau basin - Havre Trough back-arc systems. The subduction of the Louisville Seamount chain at 25.6°S affects the tectonic and volcanic system and separates the island arc into the Tonga arc and the Kermadec arc, respectively. To the west, a Miocene island arc is represented by the Lau-Colville ridge. The crustal extension between the Lau-Colville and the Tonga-Kermadec ridge started at about 6 Ma, and induced their separation and the onset of the southward rifting since about 5 Ma. Characteristics of the Tonga-Kermadec arc system include (i) the fourthfold decrease of the subduction rate from 24 cm/a in northern Tonga to 6 cm/a in the southern Kermadec trench, mainly north of 23.5°S; (ii) the development from fast spreading in the Lau basin (16 cm/a) to slow rifting (2 cm/a) in the southern Havre Trough with the transition from spreading to rifting at 23.5°S; (iii) variations in the composition and the volume of the subducting sediments and rocks (detritus from the Samoan hotspot at the northern Tonga arc; the aseismic Louisville ridge at the southern Tonga arc; increasing terrigenous sediments from New Zealand at the southern Kermadec arc); (iv) a number of active volcanic centers younger than 1 Ma and characterized by significant shallow submarine hydrothermal systems.

Aug 24, 2006