Search Documents

By Juan Pablo Segovia, Alonso Pereira, Fernando Concha, Daniel Sbarbaro, Samuel Vergara

A robust theory of sedimentation-consolidation evolved and was accepted by researchers worldwide in the last two decades of the 20th century. This theory provides a reliable method of thickener design, simulation and control. However, a process model, simple or sophisticated, empirical or phenomenological, is useful only if it is possible to determine, in an objective way, its experimental parameters. Although it is important for a mineral processing plant to perform periodical laboratory test to determine thickening parameters, and in this way adjust the operation, not always these tests represent the behavior of the material in the process. It is important to be able to determine these parameters directly in the thickeners. Research workers at the University of Concepción developed new instrumentation, algorithms and software for the determination of thickening parameters. In this paper, two new instruments for the on-line determination of the settling velocity and the compressibility of the sediment are presented and results of tests in a major mineral processing plant in Chile are described.

Jan 1, 2014

By Chao Li, Kym Runge, Saeed Farrokhpay, Dee Bradshaw

"It is well known that froth phase has a controlling influence on the overall flotation performance. Froth recovery is expected to be affected by froth transportation behaviour. The latter has been represented by different volume balance and energy balance based models. In froth transportation models based on a volume balance, the froth phase is divided into different zones. The total froth residence time is the sum of the time spent in each zone and is dependent on the cell geometry, bubble burst rate and the position that bubbles enter into the froth phase. Alternatively, the froth transportation model based on an energy balance treats the froth phase as a block. In this model, froth height above the concentrate lip is being predicted by minimising the energy of the system which is dependent on the froth geometry, froth stability and froth rheology. The froth height can be used to calculate the froth efficiency of delivering mineralized bubbles from the pulp to the concentrate lip. This paper critically analyses the current models of froth transportation in flotation, and examines the limitations of these models. The importance of froth rheology, which is the resistance to the froth flow towards the discharging weir, in determining froth transportation, is also highlighted."

Jan 1, 2014

By Alex Heath, Andrew Barycki, Baladron. Javier

"Efficient flocculation is important to thickener performance, affecting the overflow clarity, solids settling flux, underflow density and operability. Many factors affect flocculation; from the material/flocculant type, dilution of the feed and flocculant solution, mixing, to the shear rate and shear history. The flocculant addition point (or points) can be used as a tuning method to alter the effective flocculation time in a feedwell, with addition further up the feed pipe increasing the residence time but making the aggregates more prone to breakup if they experience high shear later in the process. Conversely, adding the flocculant later, eg under the feedwell shelf decreases the mixing time but allows some free (unadsorbed) flocculant to be available at the feedwell exit. An extensive trial has been performed on an operating thickener comparing seven individual different flocculant dosing positions through a Vane feedwell, and some combinations of two dosing points simultaneously. Measurements of the velocity, solids concentration and aggregate size were made throughout the feedwell at the different positions, with the dosing points significantly changing the aggregate size and clarity, and also affecting the solids concentration at some positions. The results are accessed in terms of flocculation kinetics and used as CFD validation data."

Jan 1, 2014

By F. Bello, R. Yanez, M. Pinto, T. Errazuriz

"Throughout its operation, Minera Esperanza (ME) will deposit one of the largest tonnages rates of high density tailings in the world with a solids concentration of close to 67% by weight. The tailings presently being deposited have a solids concentration of approximately 62% - 64%, and so cannot be used to directly characterize the flow and deposition characteristics of the higher concentration tailings. To increase the knowledge of the behaviour of their tailings, ME, with the support of Golder Associates, developed a large scale tailings deposition test with a capacity of 30,000 tonnes per day (1,200 m3/h). The test was carried out by depositing tailings into two large cells or paddocks in five stages. Multiple spigots were used to allow different flows to be deposited. At each stage, topographical surveys of the natural terrain and the geometry of the deposited tailings, as well as continuous flow measurement and periodical rheological characterization of the discharged tailings were conducted to create a data set against which beach slope models could be calibrated and then used to predict performance of the higher concentration tailings under different deposition scenarios. This study adopted the beach slope prediction model proposed by A.L. Li (Li, 2011). The model was successfully adjusted to the observations made during this large scale field test by applying the values measured in-situ. This paper presents the application of the model, the results obtained, the findings, and the analysis of possible future scenarios. The model was applied, using the discharge flow rate, the geometrical characteristics of the discharge area, and the rheology with its variation along the beach to estimate the development of the beach formation and the steady state of the beach slopes. Through the use of dimensionless variables, the model was applied to higher solids concentration scenarios, obtaining results that would allow beach slope estimation at different deposition stages in multiple scenarios of varying parameters such as flow, rheology and geometry of discharge area."

Jan 1, 2014

By Magnus Evertsson, Rebecka Stomvall, Josefine Berntsson

"Understanding the effect of particle shape on dry rheology is considered to be an important aspect in order to replace natural sand used in concrete with manufactured sand. Crushed particles from solid rock are normally less rounded and have less equally shaped dimensions compared to natural sand. Thus, the flowability and workability of the concrete will be different. In previous research, it has been demonstrated how different crushing techniques affects the shape of the particles. In many cases it is believed that Vertical Shaft Impact (VSI) technology is a way forward to replace natural sand. To be able to study the effect of VSI at the smaller fractions (63-2000 µm) sufficient measurements methods to determine particle shape are required. Optical tools to analyze the aggregates would make it possible to study a large amount of particles at small fractions. The determination of particle shape of aggregates is challenging since the shape is highly irregular and the size span of particles are very large. This study aim to evaluate one of the available optical tools, the Camsizer, for digital imaging determination of shape and size distribution. The available default shape parameters of the Camsizer are studied to understand the meaning of the parameters and their suitability for determining the quality of manufactured sand. To evaluate the capacity to determine particle shape, tests are made with 35 different materials. The results are compared with the dry rheology measured with the standardized "flow cone" test. Dependence has been previously proven between particle shape and the mass flow rate in the cone. Three different shape parameters, aspect ratio, sphericity and symmetry, are studied with the Camsizer and the results are compared with the mass flow rates in the cone. The results indicate a strong linear relationship between the optical parameters and the flow cone test."

Jan 1, 2014

By Egbert Burchardt

"Some of the challenges faced by the mineral industry in the future are the need to process low grade ores at the lowest operating cost, to deal with elevated energy cost and to address scarce water resources in some regions of the world. These challenges will increase the demand to develop highly energy-efficient and less water-consuming mineral processing systems. Experience from other industries suggests that HPGRs could help to achieve these goals, due to their high energy efficiency and their ability to be used as dry grinding systems. Historically, HPGRs have been used mainly as tertiary crushers in mineral applications for the production of ball mill feed. In the cement industry, however, HPGR systems have been successfully applied for grinding limestone, clinker and slag to a final product fineness (p80) of between 30 and 90 µm without the need of downstream ball milling. The total energy consumption of HPGR finish grinding systems in the cement industry has been found to be 30 to 50 % lower than in ball mill systems. This leads to the question of whether the same methodology can be adopted in the mineral industry. Such a step would require the use of dry rather than wet grinding systems. Traditionally, dry grinding systems have been only an exception in mineral processing, since most post grinding processes are wet. However, there are successful - mainly ball mill based - dry grinding examples in gold, nickel or iron ore. Experience from some of these dry grinding references are summarized in this paper. In addition, this paper explores two future-orientated questions: What opportunities does HPGR finish grinding offer the mineral industry? What are general conditions and challenges for adopting this technology for mineral applications?"

Jan 1, 2014

By Cheng Gan, Gui Xiahui, Li Shulei, Cao Yijun, Liu Jiongtian, Wu Lun

Flotation rate constant is an essential parameter in the flotation process. The fine coal sample utilized in this investigation is anthracite from the Shenhuo mine in eastern China. Fine coal flotation rate tests were conducted to compare the flotation rate constant at constant power input with that at gradually increasing power input. Results indicate that the flotation rate constant decreases with the flotation process and increases as the flotation energy is increased. In addition, the flotation rate constant is close to the maximum value. The increasing trend of the flotation rate constant gradually slows down as the flotation energy input increases.

Jan 1, 2014

By Braulio Fernández, Gonzalo Montes-Atenas

The mechanisms taking place during the leaching of chalcopyrite when it is in contact with other sulphide minerals, particularly pyrite, is still a matter not fully solved. The GalvanoxTM process has been suggested as a technical solution to extract copper from chalcopyrite at commercial level inhibiting passivation phenomena widely reported in the field of hydrometallurgy. Although there are some rules of thumb to implement the process in fully flooded stirred conditions such as the optimum pyrite/chalcopyrite mass ratio should range between 2 and 4, among others; not many research studies have been focused on studying the effect of the surface contact area between chalcopyrite and pyrite to reach best copper extraction conditions. The aim of this research work is to determine the effect of the mass and surface area ratio between the minerals and the surface area of each of the mineral species effectively exposed to the leaching solution. Different particle size distributions of pure pyrite and chalcopyrite were contacted in a small column and subjected to leach tests using sulphuric acid in concentrations close those used in industrial leaching processes. The mass and surface area ratios which optimize the extraction of copper were obtained. It was found the best leaching conditions were attained when reducing the particle size distribution of pyrite regardless the particle size distribution of chalcopyrite. Further analysis concerning the impact of this conclusions on large scale operations is presented and discussed.

Jan 1, 2014

By Cristian Melipichun, Leopoldo Gutierrez

The effect of the presence of fine particles of kaolinite and montmorillonite on the induction time for attachment of bubbles to particles of a copper concentrate rich in chalcopyrite was evaluated in this study. The results obtained from induction time measurements were correlated with data of concentrate recovery achieved from micro-flotation experiments. The effect of the presence of fine clays on the stability of air-water foams was also studied through measurements of the foam volume generated in a glass column under different conditions of air flowrate and MIBC concentrations. The experimental results showed that induction time values increased under the presence of fine clays. These data agreed with results obtained from micro-flotation experiments that showed that copper concentrate recovery decreased when clay particles were added. Although a complete explanation for these results is not available, the fact that experimental observations indicated that fine clay particles tend to adsorb on gas bubbles, suggests that the interactions between fine phyllosilicate particles and air bubbles have to be taken into account when studying the effect of clays on froth flotation. Foamability tests showed that the presence of fine clay particles increased the foam volumes only at high additions of clays and low dosages of MIBC. The results obtained at higher dosages of MIBC showed that the foam volumes decreased with the addition of clays under all the experimental conditions tested.

Jan 1, 2014

By Muammer Kaya, Sait Kursunoglu

"Energy is the major concern for society. It is expected that developing country economies and populations will grow and consume more energy. Interest in nuclear power is rising, while the world looks for non-depletable energy source that will not contribute to global warming. However, it still has concerns of nuclear proliferation, radioactive waste and safety. It is necessary to overcome these concerns if nuclear energy is expanded to developing countries. Thorium (Th) utilization as nuclear fuel will be an opening key of these difficulties because Th produces less Plutonium (Pu) and less radioactive waste with enhanced safety. Research into the use of Th as a nuclear fuel has been taking place over forty years, through with much less intensity than that for uranium (U) or U-Pu fuels. Nuclear industry is currently using only 0.7% of the available energy from mined U. With huge resources of Th and relatively little U, Turkey has made utilization of Th for large-scale energy production a major goal in its nuclear power programme. Thorium fuel is plentiful and inexpensive. Energy is major concern for developing Turkish society. Turkey, today exports more than 70% of its energy as fossil fuels. In the last 50 years, Turks are skeptical, anxious and indecisive about having nuclear energy for electricity production. In the last 10 years, Thorium is brought into Turkish government’s attention and national discussion as a new, safe, clean, affordable, CO2-free, alternative, strategic and domestic nuclear energy fuel. Turkey recently contacted four VVER-1200 type Russian Nuclear Power Reactors using U as a fuel in Akkuyu (Rosatom) and another four units will be established in Sinop in the next decade by Japan (Mitsubishi-Westinghouse). Turkish nuclear programme must envisage use of domestic Th as a fertile material. This paper briefly reviews the developments of Th-fuel cycle for nuclear energy from global and Turkish perspectives. Previous Th reserve development and recovery studies from Turkish bastnasite ore are summarized in this paper."

Jan 1, 2014

By Nani Pajunen, Kari Heiskanen

"Products filling our societal needs, like communication and transportation needs, are becoming more sophisticated and efficient. The cost has been an increased complexity of material combinations. The same trend is also seen in investment goods. As an example, different crusher types have almost doubled the power to weight ratio in a relatively short time while producing even higher crushing rations. This has been possible by high performance materials and advanced designs. Another example is new hybrid materials in prefabricated high-strength steel structures in construction with the aim to lighten the products and obtain energy savings in the use phase e.g. in transportation. This development in general has made the end of life phase obscure. Recycling is often understood as the first phase of the material cycle. This has been supported by the material centric point of view. When, say indium, has been collected and mechanically treated to a concentrated fraction, it is assumed as recycled. This is not the case. The same applies to special steel alloys where one tends to lose some of the alloying elements to slag or even into the gas phase in the melting and refining stage, not in the earlier steps of recycling. At present there is no clear understanding of recycling of hybrid materials and no clear willingness to create new functional recycling systems. As the EU directives and most of legislation worldwide are based on the material centric thinking and implemented even on total mass recovery basis there is neither legislative incentive nor very strong economic incentives to work out the problem. In our research, we focus on industrial design towards sustainability from a product centric point of view from product collection to final metallurgical steps. It is vital, in the design phase of product, to understand the effects of decisions on recyclability to a saleable raw material. Main goal of our work is to create the fortunate circumstances in supply chain - to pass the barriers and find the effective and fruitful drivers - for reasonable use of raw materials and recycling co-operation with industry. The boundary conditions in the work are extractive metallurgical performance and the economic viability of all the steps. It can be shown from our work that small design alterations may have a large impact on the recyclability. The earlier the decisions are made in the product life chain the more positive impact they will have. It can also be shown, that a strong processing and metallurgical industry is vital to any meaningful recycling of the modern EoL products. Finally, it is also question of the individuals and values: supply and demand. Are you ready to take up the gauntlet: demand recyclable products."

Jan 1, 2014

By Sanja Miskovic, Manjunath Basavarajappa

Numerical investigation of fluid flow characteristics and mixing efficiency of different impeller designs, based on the mixing characteristics of a passive scalar/tracer, is conducted using CFD for lab scale flotation cells of diameter D and height H equal to 300 mm. Fine computational mesh containing close to 1.6 million cells is used to obtain fully resolved steady state flow field close to the impeller. Unsteady scalar mixing simulations are performed on a relative coarse grid consisting of approximately 450,000 cells. Based on detailed numerical simulations, flows are fully characterized for four impeller designs at two off-bottom clearances C of 50 and 25 mm (D/6 and D/12). Passive scalar is injected from the cell bottom and the time required to attain uniform concentration distribution inside the cell volume is taken as the mixing time by monitoring scalar concentration at four discrete locations. The effect of varying agitation speed and off-bottom clearance on mean flow characteristics is also investigated. The scalar mixing results reveal regions of low mixing efficiency and are used to understand mixing process in greater detail. Through the previous research work, it was found that the main flow pattern undergoes transition from double-loop to single-loop configuration with decrease in off-bottom clearance below a certain critical height for stirred tanks using flotation impellers in the absence of stator. The inclusion of stator is found to alter the mean flow behaviour by preventing the jet from transitioning to axial type flow for lower clearance. Power numbers for different impeller designs are calculated based on the torque generated on impeller blades, and also from the total turbulent kinetic energy dissipation in the overall fluid volume. Power number is found to exhibit a significant dependence on off-bottom clearance based on the CFD results.

Jan 1, 2014

By Andrey Kozlov

The results of mineralogical?technological studies of PGM mineralization in zoned mafic?ultramafic complexes of the Ural?Alaskan type are given. The most important technological specificity of PGM mineralization hosted in dunites is its occurrence only in the form of free mineral species with predominance of Fe?Pt alloys (ferrous platinum, isoferroplatinum, and tetraferroplatinum). Technological properties, grain size, and good opening of PGM ore in grain size class +80 µm make it possible to concentrate ore using gravity methods with stadial comminution and between cycle separation of relatively large grains and nuggets into high-grade concentrates at the early stage of disintegration. Keywords: platiniferous dunites, PGM mineralization, mineralogical?technological studies and processibility research, recovery technology, gravity methods

Sep 1, 2012

By W. S. Eu

Reduction of weathered mineral ores can initiate phase transformation which can affect either their activation or deactivation, subsequently influencing the extent of extraction of desired metals in a leaching reagent. The reduction of ilmenite ores for one occurs as a series of parallel, solid state reactions which at present has no known mechanisms, although the evidence of their effects is abundant. Understanding these reactions may well be the key to uncovering the mechanism of ilmenite activation, hence enabling precise control of its reaction process to maximize yield of TiO2 extraction. However, documenting the solid state reactions in the reduction of ilmenite is challenging due to the ore complexity, the number of simultaneous reactions and the difficulty of capturing critical intermediate reactions and phase transformations during processing. The phase transformations of ilmenite minerals reduced at temperatures up to 850°C were investigated in this study. Mineral transformations were studied in-situ using synchrotron radiation based X-ray powder diffraction with temperature resolved tests. The effect of the extent of reduction and specific mineral transformations were verified by leaching reduced ore with sulphuric acid. The re-sults suggest that transformation of major mineral phases occurs within of specific window of operation and thermal treatment appears to influence the extent of activation and leachability of ilmenite minerals.

Jan 1, 2014

By K. Hori

In this study, the determination of optimal conditions for jig separation has been investigated with a TACUB jig separator. The TACUB jig, from which a Batac jig originated, is a useful gravity separator that is effective to separate crushed solid wastes as well as coarse ores. A mixture of crushed polyethylene (specific gravity 1.3) and polyvinyl chloride (specific gravity 1.5) was separated by a batch TACUB jig by varying the frequency (wavelength) and the amplitude (pulse stroke length). It was found that the sample particle layer in the separation chamber was fluidized without turbulence by the rising water pulse resulting in the separation. However, a too strong water pulse reduced the efficiency of the separation of the particles. The results indicate that the specific velocity of the rising water is necessary to fluidize the particle layer without turbulence to separate the particles. The expansion ratios of the thickness of the particle layer in rising flows were measured in a cylindrical column. The pressure losses by the particle layer were calculated from the expansion ratios and the velocity of the rising flows by Ergun?s equation. The curve of the pressure loss vs. the velocity of rising flow showed a maximum point corresponded to the point of fluidization. The velocity of a rising flow on the point of fluidization provided the optimal separation condition.

Jan 1, 2014

By Aldo Cipriano, Fernando Estrada

The mining industry is in search of control strategies that allow considering a global optimization of their processes, ensuring their stability. This has led to the application of recently developed control techniques on large-scale systems in the mining processes. One of the most important process of the mining industry is the mineral grinding, as the product particle size impacts, in a significant manner, the recovery rate of the valuable mineral in the separation stages. As a solution, a centralized hybrid model predictive control (HMPC) is presented; this control approach maintains the product particle size on a defined range and minimizes energy consumption, maintaining the grinding plant in a stable operation. As a comparison, a conventional model predictive control with an expert system to handle discrete events was developed, showing HMPC is a suitable solution that can used in the grinding process, with the benefit that it handles in the same controller both discrete and continuous dynamics and events.

Jan 1, 2014

By G. V. S. Murthy

Beach Placer Ilmenite is an important source for production of titanium metal, titania slag and pigment grade titanium dioxide. Besides, these well known applications for which Ilmenite is mined and processed, there are other emerging processes that are being tried for obtaining highvalue products. Synthesis of Ilmenite based materials for varistor applications and direct electrochemical reduction of Ilmenite to produce ferrotitanium are two such attempts being discussed in this work. In this paper, recent efforts undertaken to study the electrical and magnetic characteristics are discussed. Ilmenite, FeTiO3, is one of the mixed-valence transition metalbearing minerals, inwhich Fe can be in two different oxidation states, Fe2+ and Fe3+.. Similarly, Ti can be in Ti3+ and Ti4+.Ilmenite is inherently suitable for making Varistors, which are devices, used for limiting the transient voltage surges in a circuit. Varistors produced from Ilmenite can withstand harsh environments seen in nuclear reactors and outerspace. Electrochemical reduction of Ilmenite can be used to prepare ferrotitanium directly without any reductant. The process essentially involves removal of oxygen from the mineral through electrolytic action using calcium chloride as electrolyte and graphite as anode. At a temperature of 950°C, it is shown to be possible that all the oxygen can be removed from the Ilmenite sample, which passes through the electrolyte, to form CO/CO2 at the anode. The process has immense potential for cost effective production of titanium metal as well. Results of the above developmental works are presented in this paper. Keywords: beach placer ileminite, varistor applications

Sep 1, 2012

By Takashi Furuyama, Sukeyuki Mori, Tetsuo Ikejiri, Abel Bissombolo, Yoshitsugu Koga, Masamichi Hata

In Japan, the increasing number of automobiles newly put into circulation is followed by a larger amount of end-of-life vehicles from which valuable metals are being recovered in shredder and related plants. Nevertheless, the processing of these scrapped automobiles which has reach a recycling rate of about 75%, generates a huge volume of waste, locally known as .shredder dust., which is commonly dumped on landfills. The saturation and depletion of valuable disposal sites in the near future, as well as the social and environmental problems related to the accumulation of these residues disposals are a major challenge for the automobile shredding industry. To promote an alternative way for the management of these disposals, the authors have initiated and developed a system for their processing, on the basis that more than 90% of these residues are combustible materials that could be used as refuses derived fuel. The developed processing system points out the mechanical/physical separation of shredded automobiles residues into two streams by means of an ascending airflow passing through a vertical zigzag separator and, the compaction of the light-density fraction of materials (that is about 60% of auto shredder residue recovered as float products and mainly composed of cotton, sponges and light plastics) to form a refuse derived fuel (RDF), the density, calorific value and ignition loss of which are 1.19 g/cm3, 4470 kcal/kg and 60.7%, respectively.

Jan 1, 2003

By M. Minagawa, G. Granata, C. Tokoro, T. Kato

"In this work, we studied the mechanochemical activation of chalcopyrite by vertically stirred ball milling (VSBM) to enhance the dissolution of copper. By using x-ray diffraction (XRD) and laser diffraction particle size analysis, we investigated the effect of milling and milling conditions on particle size and phase composition of the chalcopyrite concentrate. To elucidate the efficiency of VSBM towards the mechanochemical activation of chalcopyrite, we also conducted leaching experiments in sulfuric acid-ferric sulfate media. Under all investigated milling conditions, the VSBM determined a dramatic decrease of particle size from over 100 µm of P80% up to about 13 µm. Furthermore, the XRD of the ground chalcopyrite specimens highlighted a partial oxidation of the mineral. In leaching, upon grinding by VSBM, the increase of copper extraction ranged from a minimum of +10% to a maximum of +40%, depending on the grinding conditions. In order to elucidate whether the dissolution enhancement was a consequence of the decreased particle size or of an induced mechanochemical reaction, we performed leaching experiments on activated and non-activated chalcopyrite sample having the same particle size. In addition, we determined the activation energy of leaching before and after vertically stirred ball milling. The leaching results on samples with the same particle size highlighted a greater copper extraction and higher dissolution rates upon mechanochemical activation. Whether performing grinding by VSBM or not, the leaching kinetics was found to be controlled by the chemical reaction on the surface of the chalcopyrite particle. By grinding the chalcopyrite concentrate by VSBM, the activation energy of leaching slightly decreased from 66 to 58 kJ/mol. INTRODUCTION Due to the increasing demand of copper, low grade ores and refractory minerals like chalcopyrite are expected to become the main copper source in the next years (Klauber, 2008). As a low-grade sulfide, chalcopyrite shall be processed hydrometallurgically. However, due to the formation of a protective layer of elemental sulfur during the oxidizing leaching, the dissolution of copper is slow and/or incomplete (De Bernardi and Carlesi, 2013). Therefore, the development of new technologies to enhance the extraction of copper from chalcopyrite is highly required."

Jan 1, 2018

By Kaustubh Joshi, Pradip, Beena Rai, Kesri L. Menaria, Venugopal Tammishetti

"Beneficiation of alumina rich iron ore slimes is a major challenge for the Indian iron ore industry. High alumina is deleterious for the performance of both blast furnace as well as sintering plants. Slimes generally contain 5 - 10% alumina, and hence despite assaying as high as 60% Fe, those are dumped in tailing ponds. The slimes are typically less than 37 microns. Selective flocculation of iron ore slimes using highly selective reagents is thus an option worth exploring. Our research is directed at employing state-of-the-art molecular modeling techniques for the selection/design of selective reagents for this separation. We have earlier reported our results on starch as a selective flocculant for iron ore slimes. In this paper, we present our results on the selective dispersion-flocculation of natural iron ore slimes using guar gum flocculant. With careful selection of various process parameters such as flocculant dosage, dispersant dosage, pH and settling time, we were able to obtain a concentrate assaying >66% Fe and <3.5% Al2O3 with an yield of 65 to 68% (recovery of iron values more than 70%) from a natural iron ore slime sample assaying 58% Fe and 7% Al2O3."

Jan 1, 2014