Search Documents

By Paolo Bevilacqua, Paolo Antonini, Lorenzo De Lorenzi

"Ceramic production requires large quantities of K-feldspar, which is commonly sourced from granites, alkali-granites, and feldspathic sands. These rocks contain other minerals, such as quartz and plagioclase, which are undesirable for ceramic production. Due to the coarse mineral grains that constitute these rocks, a reasonable liberation is achieved at a relatively coarse particle size.The feasibility of feldspar-quartz separation using a dynamic dense medium separation system has been investigated as an alternative to flotation techniques. The use of a two stages cylindrical vessel (Tri-Flo) was preferred to a conical vessel, due to the improved separation efficiency.In a full-scale processing plant, a dense medium separation process can be used as a K-feldspar preconcentration step. This reduces the amount of material to be treated in the more expensive processes, such as finer comminution, flotation or magnetic separation.A comparison between commercial raw materials for the ceramic industry and the “rich in feldspar” products of the Tri-Flo process is reported, and the validity of the process is demonstrated."

Jan 1, 2003

New technology for on-line particle size analysis of mineral slurries has opened up new applications for particle size measurement. In some cases the particle size distribution of the final concentrate is an important quality issue. This paper discusses established on-line particle size analysis technologies and presents experiences on the use of a new technique employing laser diffraction in several minerals processing operations. The main innovations in the new instrument are a simple dilution system and multiple scattering correction algorithm, which allows wide solids content variations of diluted sample in the measurement cell. Representative sample for laser measurement is produced by a simple and reliable dilution system. The applications discussed are; Blaine number measurement of Fe concentrate before pelletizing, grinding of variable batches of ore and paste thickener control.

Jan 1, 2014

By Mike Hollitt

The first decade of the 21st century was one of fundamentally changed dynamics for the minerals industry. Following intense globalization commencing in the late 20th century production is now concentrated into large businesses that can compete across geography in diverse commodities. Asian industrialization and urbanization is now the main driver of growth in demand for energy and materials. Demand for the output of these industries has risen sharply, reversing decade long trends to reduced real commodity prices. Supply responded with expansions of existing mining and processing operations, and large investment in new resource development. Development of new, lower grade or more remote resources was stimulated. Resource development by global entities in frontier environments reinforced the importance of effective forms of social contract, and of stronger environmental performance. The worst economic shock in decades provoked no significant pause despite large impacts on corporate ownership. State owned enterprises commenced unprecedented foreign direct investment in minerals and energy resources. A thrust towards resource nationalism re-emerged as governments sought to ensure that the export of state owned resources contributes more strongly to government revenue, reducing the burden of trade in scarce resources on other trade-exposed sectors. The unprecedented combination of forces at work has made future predictions difficult, with day-by-day volatility in anticipated corporate fortunes, and investment plans. The challenge for process innovation (and for exploration) has been to keep up, maintaining a lid on costs as lower grade and more challenging ore bodies are brought on quickly in a context of competition for land use, community expectations and continued care for natural and living environments. While new projects have provided the necessary platforms for implementation of innovative approaches, there is evidence that a gap may have emerged between the pace of growth and the pace of innovation. The history of a century of process innovation in the context of growth of output, declining resource grades and commodity prices is presented. The necessary conditions for accelerated process innovation are considered, and future needs and approaches are discussed. Keywords: process innovation, resource development

Sep 1, 2012

By V Radmehr

Ammonia and Amonium salts have been recognized as effective leaching agents in hydrometallurgical processes due to low toxicity and cost, easy recovery and high selective recovery of metals. New research findings of considerable advantages of leaching by these agents and elimination of problems associated with acid leaching has resulted in a new approach in the world to this method. The investigations in this field indicate more frequent use of this method for extracting copper from ore and concentrate relative to other basic metals. In this paper, we have attempted to describe the basis and different ammonia leaching methods and present the major research activities in this field for copper. We have also presented the latest findings and related novel processes. Comparative assessment of advantages and disadvantages of this method relative to acid leaching method, kinetic study of copper ammonia leaching and evaluation of Eh-pH diagrams in a system containing water and ammonia are other parts of our study. Finally, by describing the studies on copper extraction from the resulting pregnant solutions, the applicable extraction agents have been reviewed.

Sep 1, 2012

By In-Kuk Bae, Kwang-suk You, Joobeom Seo, Kwanghyun Bea, Hyung-Seok Kim

Arsenic in base metal sulfide ores is highly penalized owing to high costs for its control in metallurgical processing. The arsenic element in the lead-zinc ore, which is target ore in this study, has been shown to be in the form of arsenopyrite. Experimental work in this study is about arsenic rejection flotation, using depressant suitable for the removal of arsenopyrite from the Pb concentrate. The arsenic rejection flotation also included the oxidation treatment of Pb concentrate with H2O2. In this study, the Pb concentrates containing 80.7% Pb and 0.25% as was obtained with the additions of aluminosulfate as arsenic depressant. And through IR measurement, it was also known that the addition of aluminosulfate during arsenic rejection flotation formed calcium aluminosulfate hydrates on the surface of arsenopyrite particle, resulting in rendering arsenopyrite hydrophilic.

Jan 1, 2014

By Ana C. C. Pacheco, Maurício L. Torem

"The aim of this work was the study of the effect of the type (Fe3+, Al3+ and Fe3+ and Al3+ mixture) and of the coprecipitant concentration on As5+ removal by ACF. Removal of As5+ using Sodium Dodecylsulfate (SDS) as a collector was studied by Adsorbing Colloid Flotation (ACF) at laboratory scale. The morphology of the precipitate retained in the foam was analyzed by Scanning Electron Microscopy (SEM/EDS).By comparing the coprecipitant type and concentration studies it could be concluded that As5+ removal in the presence of Fe3+ (160 mg.L-1) alone, or a Fe3+ (80 mg.L-1) and Al3+ (40 mg.L-1) mixture, is equivalently effective (99,9%) and greater than in the presence of Al3+ (80 mg.L-1) alone (97,7%).Through SEM/EDS analyses, it was possible to observe that both morphology and composition of the precipitate produced in the solution and retained in the foam depend on the physico-chemical conditions of the system, that is, on the species present in the solution."

Jan 1, 2003

By Adam Jordens, Olga Kuzmina, Christopher Marion, Kristian Waters

"In order to meet the growing demand for non-Chinese rare earth suppliers many new rare earth (RE) mineral deposits are currently under development, however these deposits typically include many minerals for which there is little processing information available. One of these deposits is the Nechalacho deposit located in the North West Territories of Canada. This deposit contains multiple RE minerals including bastnäsite, zircon, fergusonite, allanite and monazite. The work presented here investigates the use of different classes of flotation collectors (carboxylic acids, hydroxamic acids, phosphoric acids) typically used in RE mineral flotation to float the Nechalacho ore directly. Flotation tests are also conducted as the final step in a beneficiation process incorporating centrifugal gravity concentration and magnetic separation. This combination of centrifugal gravity concentration and magnetic separation rejects low specific gravity gangue minerals such as K-feldspar and plagioclase and concentrates high specific gravity minerals such as magnetite and hematite. The removal of low specific gravity gangue helps to improve flotation and the removal of ferromagnetic iron oxides is important prior to flotation using certain chelating collectors."

Jan 1, 2014

By M. M. Yahyaei

The Sarcheshmeh new concentration plant uses a 32 ft×16 ft constant speed (10.5 RPM) SAG mill with two 5500 hp motors which could rotate in two directions. The mill liners are chrome-molybdenum steel casting type with a Brinnell hardness between 325 and 375 with the lifter face angle of 14° and lifter height of 152 mm. The shell liner consists of 120 (two 60 rows) pieces with a High-High configuration in a rail design. A specially designed liner wear profile measuring device enabled fast and accurate measurements inside the mill during the mill shut-down periods. The measurements indicated that the liner wear profile along the liner length is non-uniform and the highest wear occurs between 1.25m and 2.75m of the mill length. The average weight of liners at the time of removal was 47% of the original weight indicating a significant metal loss. The modification of liner shape was undertaken with the aim of having a uniform profile at the liner removal time. The proposed liner unlike the pervious type did not have a uniform shape with a lifter height of 187mm at the section where the wear rate was high. It was believed that this new profile could arrive at a uniform profile at the liner change out time. A study was also directed to the possible change of charge motion due to the liner profile modification. The dynamic behaviour of charge was investigated through the analysis of forces acting on a single ball using mill characteristics such as mill diameter, rotational speed, lifter height and release angle. The simulation of charge motion with this method and Milltraj TM software indicated that the impact position of charge will change only one degree due to the maximum increase of 35 mm in the lifter height. This assured that the installation of the modified liner would not have any adverse effect on the mill because of ball impacting the mill shell. It was predicated that the amount of scrap metal will reduce to 30% from the current value of 47% beside 1500 h increase in the liner life time.

Jan 1, 2014

By Mario Gerards, Marco Steinberg, Jan Huben

"Wet high intensity magnetic separation or WHIMS is a widely used technical process for the recovery of magnetic susceptible iron ore particles, mostly for fine and ultrafine grain sizes. The JONES® WHIMS - Wet High Intensity Magnetic Separator, has been used for many years and in countries all around the world. This paper outlines the physical principles utilized for the separation inside the unit, as well as some of the recent changes and developments on the design. It will also give an outlook on the theoretical potential of different alternative yoke materials. The aim of this paper is to analyse the suitability of different yoke materials to improve the equipment. This will be done comparing the magnetic and mechanical parameters and analysing availability and price to find the best compromise regarding cost and benefit. As far as the different kinds of materials are concerned, a special material has been identified as suitable during the comparison exercise. After running the economical calculations, especially with respect to the reduction of the total power consumption of the equipment, a tremendous reduction of the total power consumption has been determined. In addition, to the theoretical exercises and due to the promising results of the same, the Pilot Unit P 40 of the JONES® WHIMS has been manufactured with the special material in order to get practical results as well. Finally, this paper outlines the theoretical and practical results focused on the power consumption. The results are showing that the total power consumption can be reduced tremendously. Hence, the way for a new generation of JONES® WHIMS - environmentally friendly - has been paved."

Jan 1, 2014

By Masakazu Niinae, Kenji Aoki

"Electrokinetic soil remediation by electroosmosis and ionic migration is restricted to soluble substances. At a higher pH, the soil particles sorb more heavy metals than at a lower pH and the precipitation of heavy metals are promoted. Both mechanisms make heavy metals immobile, rendering cleanup more difficult and electrokinetic extraction inefficient.In this study, the effectiveness of introducing a complexing agent to enhance the removal of cadmium from kaolinite in the region of neutral pH by ionic migration is examined. The complexing agent selected was ethylenediaminetetraacetic acid (EDTA). The investigation was carried out in a laboratory-scale column containing kaolinite contaminated with cadmium. As the results of the study, cadmium migrates toward the anode without accumulation of cadmium and is successfully removed at the anode reservoir."

Jan 1, 2003

By Yang Zhao, Tao Xiu-xiang, Chen Song-jiang

"China is rich in low-rank coals that account for 45.68% of existing coal reserves in China. The clean and efficient utilization of low rank coals is of great significance for ensuring the effective energy supply and promoting economic development and environmental protection. In order to solve the difficult problem in flotation of low rank coal, it has become the focus of research in the related field that oily bubbles instead of air bubbles are taken as a carrier in flotation to improve the attachment efficiency and recovery of low rank coal. In this paper, low rank coal slime collected from Shendong mining area was used as the experimental material, and it focused on the characteristics of oily-bubble flotation process of low rank coal. Additionally, difference in conventional flotation and oily-bubble flotation was discussed. The induction time between air bubbles, oily-bubbles and fine low rank coal particles was measured. The results indicated that the induction time between oily-bubbles and coal particles was obviously lower than that of air bubbles. By comparing the foam height of air and oily bubbles, it was found that the amount of oily bubbles is less than air bubbles, causing relative low flotation rate of oily-bubble flotation at initial stage. Besides, the maximum foam height and half-life of air bubbles and oily-bubbles were measured respectively. The results showed that the stability of oily-bubbles was higher than that of air bubbles, which is benefit for the enrichment of concentrates. The clean coal water recovery of oily-bubble flotation is lower than that of air bubble flotation, which indicated oily-bubble flotation is lower in water entrainment. INTRODUCTION China is the largest energy consumer in the world, accounting for 23% of global energy consumption in 2016 and 27% of global energy consumption growth. Whereas coal is taken as the major primary energy source and its share of China’s primary energy consumption is 62% in 2016, in which the low rank coals, such as lignite, long-flame coal, weakly caking coal, and non-caking coal, accounted for about 50% of total coal production capacity (China’s energy market in 2016, BP). Moreover, the exploitation and utilization of low rank coals and other coals that are difficult to float have been an important strategy for China’s sustainable development of the coal industry (Liu et al., 2014). However, the combustion of low-quality coals leads to a serious environmental pollution. In addition, the deterioration in geological conditions of coal resources, and the increasing improvement in the mechanization for mining significantly caused the increased amount of fine coal."

Jan 1, 2018

Pure camsellite samples were prepared through crushing, sorting and grinding the high-grade iron-containing camsellite ores from Fengcheng, Liaoning, China. The flotation behaviour of camsellite was studied via a systematic investigation of camsellite flotation re-covery changes as a function of choices and dosages of collectors and depressants at different slurry pH. The results showed that at pH 8.5 to 9.5, the recovery of camsellite reached the maximum at 90%~93.5% using dodecylamine as the collector, while under the same condition a recovery of 84%~86% could be achieved with sodium oleate. The adsorption of dodecylamine was not affected by the addition of sodium hexametaphosphate, but the adsorption of sodium oleate could be significantly depressed. This implied that sodium metahexaphosphate could be used as an effective depressant for the other associated minerals during the dodecylamine flotation of camsellite. When starch was used as the depressant, the flotation of camsellite by sodium oleate was almost completely depressed in the alkaline conditions. Significant depressions were also observed when calcium chloride was added in the camsellite-sodium oleate system. The higher the slurry pH is, the stronger the depression. Zeta potential measurements indicated that the flotation was mainly initiated by the electrostatic adsorption of the collector on camsellite. X-ray photoelectron spectrometer (XPS) analysis showed that the adsorption was originated from the electrostatic attraction between the N atom in dode-cylamine and B atom in camsellite. Dodecylamine had a higher coverage on the camsellite surface than sodium oleate.

Jan 1, 2014

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisingerm

"As deposits of high-grade base metal sulphides become depleted, attention must be focused on the treatment of complex sulphides, which contain significant fractions of precious metals such as gold and silver. Acid pressure oxidation is a promising process for these materials and the recovery of silver and gold will improve the economy of the process. Gold can be recovered from the oxidised residues, however, silver is incorporated into the jarosite specie and the cyanidation of the resulting residue yields very low recovery.Pressure oxidation of various complex sulphides was carried out at 110-150°C in sulphate media with additions of potassium iodide under conditions similar to industrial autoclaving. The resulting residues were subjected to cyanidation. High recovery of silver, up to 98%, was achieved because its incorporation into lead-hydronium jarosite during the pressure oxidation was minimised, while its deportment into the cyanide-soluble silver iodide was favoured. Silver recovery decreased slightly at high temperatures (140° and 150°C) because of the enhanced stability and kinetics of lead-hydronium jarosite, but this could be overcome by increasing acidity and iodide concentration of the autoclave slurry."

Jan 1, 2003

By John A. Herbst

The Mineral Processing Industry needs accurate Production Simulators for the design of future plants and expansions. To achieve this, these simulators should not only provide an accurate portrayal of the dynamics of individual pieces of equipment they should include the impact of discrete stochastic events such as scheduled and unscheduled maintenance so the relationships between availability, equipment sizes, and plant capacity are understood. To provide such a tool accurate dynamic Population Balance Models need to be combined with solid discrete event modeling. The current paper provides a description of how these two disparate modeling techniques were combined and the associated benefits from this combination. Keywords: dynamic plant simulation, population balance models, discrete event models, prefeasibility and feasibility studies, plant design and expansion

Sep 1, 2012

By F. A. V. Guimarães, A. M. Costa

"The moisture in sintering is a very important parameter for the performance of the process. It allows that the granulation takes pace in an efficient way making the water bridges between the bigger particles used as nucleus and the finer particles that perform the coating of those coarse particles. The formation of the micro pellets is extremely important to prevent loss in permeability of the bed in the sintering grate, avoiding excessive fuel consumption and producing a quality sinter. The aim of this project is to use some of the methodologies for determine the saturation degree on ores and coal to determine the optimal moisture for sintering. In the sinter pot grate series, 3 to 4 assays in a series of 10 are required to determine the optimal moisture for the process. The saturation degree curve test has shown that is really viable to use this technique to skip those tests and go directly to the series to determine productivity and the coke / anthracite consumption. In an industrial scale can be used to adjust the water addition in the conventional mixing methods used in the sintering plants to increase productivity in the process.INTRODUCTION Sintering Sintering is a high temperature agglomeration process in which iron ore fines are partially melted and bonded together using fluxes and a source of fuel, usually coke breeze. The agglomerated product, sinter, has improved metallurgical properties making it an ideal ferrous burden that enable the passage of hot gases in the iron-making blast furnace. The sintering process is normally carried out over three basic stages: granulation, ignition/sintering, and product sizing. In the granulation stage, iron ore fines (usually a blend of selected ores), sinter return fines, fluxes and fuel, and are mixed with water and micro-pelletised in a drum or disc before being introduced in the main granulation circuit. (Wang, Teng, & Wang, 2017)."

Jan 1, 2018

By Avinash Tripathi

It is now well known that the size distribution of the particulate solid has a significant effect on the breakage behavior of particles in the wet as well as dry modes of ball milling operation. In the context of the size discretized batch grinding kinetic model, grinding behavior of particles is characterized by the breakage rate parameters, k, and breakage distribution parameters, B. Understanding the nature of variation of these two sets of parameters with particle size distribution is important for simulation and control of operation of production mills. However, so far it has not been possible to track the variation of both the set of parameters with grinding time simultaneously. In this paper an attempt has been made in this direction by using a modified functional form approach with time dependent constants. Keywords: dry and wet ball milling, breakage rate and distribution parameters, effect of particle size distribution

Sep 1, 2012

By Sarthak Kaushik

Zeta potential measurements show that the isoelectric point of crandallite, in aqueous solution of 10-2 N sodium chloride is at about pH 5.5. Measurements of turbidity confirm the point of zero charge or crandallite. Calcium ions specifically adsorbed on the surface and thus changed the zeta potential and turbidity. From the measured data, it is confirmed that starch acts as a flocculent for crandallite. Oleic acid, which is a collector used in phosphate ore processing is weakly adsorbed on the surface of crandallite. This results in hydrophobic coagulation of particles resulting in a lower turbidity.

Sep 1, 2012

By Markus A. Reuter, Albert Scholte, Ewoud V. Verhoef, Gerard P. J. Dijkema

A dynamic, interactive map has been developed of the life cycle of a number of metals, from mining through to minerals processing, metal production, product manufacturing, recovery and waste management. Whilst the existing metal process network and waste management infrastructure provide substantial scope for (product) design, these also limit change due to the complex interdependence of metals, both in production and recovery, and the strong path dependency of industry and infrastructure development. Therefore, models for dynamic simulation were constructed that allow the specification and evaluation of the metal process network and waste management infrastructure ‘products’ over a longer time span. The model has been constructed using a bottom-up approach, to enable assessment of the environmental aspects of metallurgy and to simulate changes in the system structure and technology, i.e. from reactor or individual process step up to integrated material cycles. The model comprises hierarchical mass balances and linear models of individual processes and sub-processes. Thus, at lower system aggregate levels an increasing level of technical detail is represented. Data reconciliation has been used literature data on process feed, products and residue composition to calculate representative and reliable split factors around each (sub-)process. World production figures on process capacity and recovery rates are be used to calculate the relative contribution of processes. The dynamic map is illustrated with a case on the introduction of lead-free solder.

Jan 1, 2003

By Jihoe Kwon, Daeyang Lee, Mario Fujimura-Kashiwagui, Heechan Cho

"Calcium carbonate is one of the most widely used mineral in today's industries such as plastic, paper and pigment. There are many essential physicochemical properties required by each industry field but the most common requisite is size. One way to achieve appropriate size is grinding. Grinding is typically an energy intensive process, consuming about 40% of total energy cost in mineral process. Due to that reason, optimization of grinding process is a critical element to achieve price competitiveness. Two different type of grinding apparatus were hired to find out optimum condition in terms of energy efficiency. Utilizing samples containing 10, 20, 30 and 40% solids concentrations, a 1l batch type attrition mill was operated as the first grinding step at various operating speed with 1? to 5? grinding media in order to study the optimum operating conditions to reach submicron particles. Next, a 0.15l vertical beads mill was tested as next step with 100? to 500? grinding media to study the optimum conditions in the submicron range. Net energy and the specific energy input was measured to reach stated size ranges. Also, using a back-calculation based on the population balance model further operating conditions were studied. There were several competitive combinations which showed significant energy efficiency improvement when compared with the single step grinding."

Jan 1, 2014

By Alejandro Uribe-Salas, Fabiola Nava-Alonso, Gloria Dávila-Pulido

This paper presents results of an experimental study performed on the role of calcium sulfate present in flotation water on sphalerite flotation in the Pb/Cu circuit (non Cu-activated sphalerite) and in the Zn circuit (Cu-activated sphalerite). In the Pb/Cu circuit calcium ions adsorb on the negatively-charged sphalerite favoring xanthate adsorption and therefore making sphalerite floatable; experimental measurements show sphalerite contact angle increases with calcium concentration while xanthate adsorption onto sphalerite increases with the increase of pH and calcium concentration. Gypsum (CaSO4·2H2O) eventually present due to calcium sulfate precipitation is not detrimental to flotation at this stage since it is negatively charged at pH 9 and therefore, does not adhere onto the surface of negatively-charged sphalerite. In the zinc circuit, Cu-activated sphalerite decreases its negative charge (or even becomes positively charged) and develops some hydrophobicity due to the polysulfide produced by Cu-activation. At this stage calcium ions do not interact with the mineral surface and therefore do not favor xanthate adsorption; nevertheless, precipitated gypsum particles do adhere onto the mineral surface, greatly affecting its floatability (e.g., contact angle). Addition of sodium carbonate to dissolve gypsum and to precipitate calcium as calcium carbonate, which disperses in the bulk of the suspension, effectively restores mineral hydrophobicity. SEM observations coupled with EDS analysis clearly illustrate and support the above sequence of events.

Jan 1, 2014