Search Documents

By Cathy Aimone-Martin, Kristin Dunlap Kolden

Blasting was conducted for the Army Corps of Engineers (Corps) in the Columbia River near Saint Helens, Oregon during 2009 and 2010 to deepen the navigation channel as a final phase of a dredging project to accommodate larger container ships. The Columbia River Channel Improvement Project (CRCI) required 4 months to blast and dredge 300,000 yd3 (229,366 m3) of basalt from the bottom of the channel to allow Post-Panamax vessels with drafts up to 50 ft (15.2 m) access to the Ports along the River. Explosives charges were limited to 90 lbs (40.8 kg) per delay for the protection of fish and marine life in the area. A fish mortality study and marine mammal monitoring program was also required by the Corps. Underwater overpressure monitoring was required for each blast and peak overpressures measured 10 ft (3.1 m) above the river bottom 140 ft (42.7 m) from the closest blast hole were not to exceed 70 psi (483 kPa) with a cautionary level of 40 psi (276 kPa). Specifications required sampling rates of 500k S/s and PCB Peizotronics tourmaline pressure sensors. The Corps granted permission to co-locate additional ceramic-type sensors at different sampling rates to design redundant monitoring systems 140 and 300 ft (42.7 and 91.4 m) from blasting and develop a site-specific overpressure attenuation model for the project. This paper presents the correlations of overpressure with cube-root scaled distance factors, a comparison of measurements using three different pressure sensor systems, and a discussion of blast design influence on overpressure measurements.

Jan 1, 2014

By Pierre DePasquale, Ricardo Chavez

Lowering of quarry energy consumption participates to answer both environmental and financial issues. The “EE-Quarry” European project, supported by the European Commission (EE stands for Energy Efficient), develops a new and highly effective modelling and monitoring Energy Management System technique to improve Energy Efficiency and move to a low CO2 emission rate in the nonmetallic mineral industry. Within this global quarry project, blast design, as the first link in the chain, has to be optimized in order to satisfy requirements of downstream operations. The authors have been developing and implementing an operational methodology using continuous field measurements and field adaptation methods for blast design. It drives the drilling and blasting work, aiming at a more energy efficient and environmentally friendly operation. Based upon actual local conditions (rock-mass assessment, face geometry, borehole deviations, etc.), blast patterns are optimized through a specific hole-by-hole blast design software. It provides a better and more consistent energy distribution, to achieve a better rock fragmentation, while avoiding explosive overconsumption. The software also calculates total energy inputs and the drilling and blasting contribution to Greenhouse Effect. Coupled with methodical fieldwork and variable density explosives, it has been leading to a real reduction in energy costs and greenhouse gas emissions. As the project is now reaching its final stage, demonstrations were conducted in various quarries around Europe. Several simulations were carried out and compared to the site data, in order to propose enhancements for the different phases (extraction, loading, hauling, crushing and transport) while bearing in mind the environmental impact of the quarry. This blasting methodology allows to assess the carbon footprint of drilling and blasting in conjunction with the downstream operations, thus to evaluate the global carbon footprint of quarrying. Copyright ©

Jan 1, 2015

By Andrew Ritter, Victor I. Montenyohl, Stephen R. Winzer

Thirty-seven open pit production blasting operations have been monitored using high-speed cameras running between 500 and 7000 frames per second. Analysis of the resulting films reveals irregularities in timing including sequencing errors and crowding (holes firing less than 8 ms apart), confirming results of laboratory testing of ms delay blasting caps (Winzer, 1978). Where blasting parameters are otherwise constant and within recommended guidelines (stemming, spacing, burden, etc.), timing problems dominate the overall performance of the blasting operation. Model tests in layered Homalite 100, designed to simulate joint or bedding planes in rock, indicate the importance of the stress waves generated by the explosive in developing the crack network which is ultimately responsible for the fragmentation seen in the resulting muckpile. These mechanisms are strongly supported by high-speed film studies at Pinesburg, Maryland. Experiments in controlling relief in deep shots (where depth approaches the lateral extent of the bench blasted) using borehole geometry and hybrid initiation systems (electronic timer and pyrotechnic delays) were carried out. The results suggest that the 1 me/ft. of burden guideline developed by Bergmann et aI., 1974 is too short, and that much longer times are necessary to optimize fragmentation and muck digability. Longer times are found to reduce noise, vibration, and flyrock.

Jan 1, 1979

By D Maxwell Ellett

This report presents an evaluation of knowledge concerning a process used in predicting ground motion resulting from large scale conventional explosive detonations, The shots were set off in Arizona in connection with copper ore recovery activities.

Jan 1, 1976

By Ralph E. Burnham, J. Kelly Ratliff

"The words “dynamite,” “TNT,” “explosives,” and “blasting” typically cause the general public, andjurors, apprehension and fear. Although blasting operations conducted by well-trained, skilled, andexperienced blasters rarely cause damage or injury, the public’s perception of blasting is that it isdangerous, disruptive, and results in damage to nearby properties. As a result, blasting operations have always resulted in complaints, claims, and lawsuits. However, in recent years, the public perception combined with an increase in public opposition, social media, more stringent regulations, predatory plaintiffs’ attorneys, and the application of strict liability to blasting claims has resulted in an increased threat of litigation to blasting companies and individual blasters. Consequently, many blasting companies find themselves receiving more complaints, involved in more litigation, and facing an alarming number of frivolous claims, which can result in increased insurance costs and other financial tolls. Accordingly, today’s blasting companies must be prepared for litigation and take steps to eliminate accidents and claims before the first shot is detonated on a job. The best way to accomplish this is standard operating procedures that incorporate best management practices, industry standards, and regulations in daily operations. This paper outlines some of the considerations that a blasting company should incorporate into its standard operating procedures before, during, and after the shot."

Jan 1, 2016

By Joshua Micah Hoffman, Lifeng Li, Jhon Silva-Castro

Since millisecond detonators were first introduced, at least two variables among others have been more closely considered when timing a mining blast; the accuracy and the precision of the initiation system. Unfortunately, those variables are often ignored when designing timing for mining blast. Despite the lack of consideration of the characteristics of the initiation system, in some situations, e.g., firing a blast hole with one deck and two detonators, changes in the blasting sequence can be the results of the overlapping between blasting charges. The consequences of such overlapping involve flyrock events, fragmentation and diggability problems, and other difficulties affecting the operation of the mine.

Jan 1, 2015

By Jason Rock, Rob Thompson, Lee Julian

Reactive ground is ground that undergoes a spontaneous exothermic reaction after it comes into contact with nitrates. This is commonly caused by inert rock hosting sulphide minerals, such as pyrites that act as the reagent. The presence and subsequent rate of reaction with nitrate based bulk explosives can be difficult to predict. Once identified, only explosives that are tested and proven to be compatible with the reactive ground may only be used. These typically take the form of inhibited ammonium nitrate emulsion blended with a limited volume of ANFO or porous prilled ammonium nitrate (PPAN) to ensure that all AN prills in the blend are wholly encapsulated and thus protected from the reactive ground. The requirement for high emulsion content bulk products limits the suite of products available for use to high energy, and high expense products. Further, if chemically sensitised products are used, charged holes must be left unstemmed to allow for gassing to occur, adding delay and exposing the blast crew to an unconfined charge in reactive ground. A range of inhibited products has been developed that are solid sensitised and can be bulked to as low as 0.9 g/cc (56.2 lb/ft3). The use of a solid sensitiser enables stemming to occur immediately after each hole is charged, confining any unplanned detonation more safely within the rock mass. The effective and precise manufacture of bulked inhibited products required a new and innovative Mobile Processing Unit (MPU) design. This MPU required the ability to blend two solid raw materials (AN prill & sensitiser) along with two liquid ingredients (AN emulsion and process fuel). This MPU has been designed, manufactured and has used successfully to manufacture low density inhibited explosives. This paper presents an innovative shift in inhibited bulk products with specific reference to their manufacture and application.

By Joel Warneke, Cristian Caceres, Ed Mchugh

NIOSH researchers collected basic data from two blast rounds at the SSX-Steer Mine as a component of a larger study on controlled blasting, the goal of which is to reduce injuries from falling rocks in underground mines. Drilling and blasting procedures at the mine were observed. Rock mass property data were collected, a program of seismic monitoring and analysis was conducted, and 3-D laser survey scans of the workings before and after each blast were performed. The geologic data showed that the rock mass quality was characterized as poor to very poor. It was essentially uniform within the panels examined. The recorded seismic data indicated that fill material acted as an effective damper to seismic energy. The pre- and post-blast laser scans showed both over-break and under-break conditions, highlighting the problems associated with blasting a weak rock mass. By comparing the achieved results to the intended design, potential improvements in the drilling and blasting practices can be identified. Comparison of these data with similar data from other mines will help define how various combinations of rock and fill behave during blasting. Through studies such as these, data collection procedures and analysis techniques can be refined. An ultimate goal is to develop blast procedures tied to rock mass characteristics that can minimize damage to rock in the perimeter of the opening, limiting the amount of loose rock and improving the safety of miners.

Jan 1, 2008

By Larry Schneider

In the construction field and to a lesser degree in mining, flagman are often necessary to move traffic and or pedestrians through work zones. Everyone readily recognizes that they are essential for the safety of the general public and the employees on the job. What is not often considered is the safety of the flagmen themselves. Actually, let’s call these employees “flaggers” recognizing the fact that there are as many women as men doing this job. The first problem we need to overcome is the misperception that flagging is a low skill function that can be done by any untrained employee. The reality is that the flagger works in a very hazardous position with serious responsibility for the safety of his fellow employees and the public at large. And to do this job properly re q u i re s that the flagger receive sufficient training before being sent out to the highway. It is also necessary to convince the flagger of the value and importance of their job in order to motivate them to do a professional job.testing, documentation of both, and accurate re c o rdkeeping are key aspects of HM126F. Of course, training and documentation requirements will vary depending on the type of operation involved, and there may be some differences in the application of requirements depending on your jursdiction. Nonetheless, failure to train and properly document such training can result in heavy fines and/or penalties.

Jan 1, 2004

By Peter Duniam, Vivian Patz

History of the ExEx 1000 CAB system. l What we’ve learned using electronic timing. l Requirements for a second generation. EDD system. l The ExEx 2000 system - simple, versatile and cost effective

Jan 1, 1997

By Diego Quezada, Carlos Munoz, Marco Arellano

It is well-know that the presence of fine materials in mining has a direct impact on the plant processes with a great influence in the total amount of ore production and recovery. In Cu mining heap leaching is affected negatively by the presence of fines material (< 100 # Ty) in leaching piles, where a decreasing in Cu recovery is achieved in a lot of cases. D&B practices used normally in mine operations can generate fines > 4% in blasted piles, but the principal effects are reflected in the downstream processes where pre-conditioning post-blast materials release greater quantities of fines.

Jan 1, 2010

By Nan H. Lee, Christopher J. Hunter, Stephen H. Chung

Several factors affect the productivity of mining operations. The geological structure of a mineral deposit and the fragment size of blasted material are considered to be most influential. It is well known that productivity varies with mucking cycles and that this is related to the explosive energy produced by a blast.

Jan 1, 1991

By Saeed Karimifard, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Frank Chu, Caitlin McKinnon, Tetiana Konstantynivska, Glen Turner

We propose a particle size analysis solution for haul trucks that does not impact current operational workflows. Using artificial intelligence (AI) and 3D imaging technology, our solution reliably localizes and identifies haul trucks as they drive by, then accurately calculates the particle size distribution of the visible material in each truck load. In this paper, we identify the challenges of designing and implementing the proposed solution and explain the strategies we employ to overcome these. We also discuss a method for boulder detection that leverages the existing deep learning architecture to significantly reduce crusher downtime caused by oversized rocks

Feb 1, 2020

By Joshua Micah Hoffman

While it is easy to state that meaningful involvement of the community can play a critical role for a successful blasting operation, following through with this involvement is not an easy task. Structured Public Involvement (SPI) is a developed protocol for involving communities in project planning decisions and could be readily applied to the blasting industry. SPI was developed for the purpose of collecting quality public input about public transportation projects. The purpose of SPI is to bring about stakeholder satisfaction with potential projects by allowing controlled input from the stakeholders. It was designed and intended for democratic societies that have come to expect a voice in public projects. While blasting operations are not always in the domain of public projects, the fundamental process outlined by SPI can be useful for collecting feedback from the immediate public around blasting operations.

Jan 1, 2014

By Sam Taoum, Omar Riahi

Few tools allow for accurately tracking ore dilution after blasting. Existing methods often rely on data analysis or linear interpolation of velocity, which can be imprecise and less effective in varied geological settings. A promising alternative is the use of numerical simulations, which involve complex mathematical calculations incorporating real physical data about explosives and geological characteristics. These simulations can model blast-induced fragmentation and subsequent ore dilution with greater accuracy, providing detailed insights into blast dynamics by considering factors such as explosive type, blast pattern, and rock properties. Numerical simulations integrate data from sources like seismic sensors, blast monitoring equipment, and geological surveys, offering a holistic view that single-method approaches cannot match. By simulating different scenarios, mines can predict the outcomes of various blasting strategies, optimize blast designs to minimize ore dilution, and maximize recovery. Advanced numerical simulations enhance the prediction of fragmentation distribution and size post-blast, crucial for effective dilution control and maximizing ore recovery rates.

Jan 21, 2025

By Jorge Alvarez

In a large-scale open-pit mining operation, continuous efforts are made to control damage to the slope walls. An essential tool in this effort is determining the PPVc (critical peak particle velocity) in areas of interest. By knowing this value and generating criteria, drilling and blasting designs can be established to reduce vibrations that affect wall construction. It is crucial to understand that the PPVc changes as different mining phases develop, especially due to exploitation on the benches, which leads to vertical inherited damage. Therefore, it is imperative to regularly update the PPVc based on field tests that provide accurate data. With this information, vibration damage criteria can be established, and drilling and blasting techniques can be designed to minimize the impact on the remaining rock mass. This document presents a methodology for generating scaled criteria that best represent the reality of the rock mass.

Jan 21, 2025

By Francisco Sena Leite, Raquel Sobral, Vinicius Gouveia de Miranda, Céu Jesus

"This document investigates a newly developed technique with the objective of improving terrain triangulation models (horizontal/sub-horizontal and vertical/sub-vertical terrains), mainly blast free faces. The algorithm uses multi-linear regressions to generate the best point cloud projection plane by applying the residues modulus minimization so as to create the finest 3D triangulation model. A change of base is required to create a new set of coordinate axis and generate completely new projection planes. The projection plane residue analysis is inferred in order to avoid or reduce the outlier points. The dataset is composed of 12 terrain models obtained from photogrammetry and a 3D Laser equipment thatgenerates georeferenced cloud points. This new technique is validated by the analysis of the obtainedcritical burden by the improvement of the general aspect view of the terrains and the capacity of outlier’s detection. The result and the quality of the algorithm demonstrates the improvement in the triangulation mesh, reducing errors in the calculation of over/under burden, free face volumes, cavities and, therefore, in the estimations of clearance/safety distances."

Jan 1, 2017

By Andrew Theobald, Peter Dare-Bryan, Trevor Byers

The use of advanced modelling techniques and the timing flexibility of electronic initiation systems allows for unprecedented control over blast outcomes as shown in several complex blasting problems experienced by the open pit operation Xstrata Ernest Henry Mine (EHM) in north-west Queensland, Australia.

Jan 1, 2010

By Amanda Verno, Danilo Coppe, Andrea Reggiani, Adolfo Bacci

The methodological example that comes from the demolition of the Genoa grain silos, should not been considered as an auto-celebration of a difficult project successfully executed, but should serve as an example of a new generation of demolitions where different technologies, often in competition, come together to obtain the optimal solution of a problem. Dynamite, diamond wire and hydraulic excavators overcame the most impressive building in town, working in very little spaces and on a geotechnically difficult site; moreover, a study on the dynamics and the effects of the impact of the structure, an analysis of the presence of potentially explosive dusts and an extensive vibrometric monitoring supported the design and the development of the operations.

Jan 1, 2005

By Nathan Rouse

This blast mitigation study examined the effects of a barrier wall on explosively driven pressures. This area of blast mitigation is of interest due to the many different applications involved in protecting a target from an explosive attack.

Jan 1, 2012