Search Documents

By Michael S. Wieland

Underground coal-mine explosives (permissibles) can be substantially degraded by the underground stress waves from the explosion of neighboring borehole charges. This cross-borehole interaction generally yields the worst receptor (impacted) charge performance when the borehole separations are too close. For explosives which recover, the receptor degradation is worst when the delay until firing is small. Except for a poor quality muck pile or unreacted cartridge fragments, degraded charge malfunctions of this type are difficult to detect in coal-mine delay blasting. A simulator which reproduces the underground wave/receptor charge interaction and special underwater donor/receptor tests were utilized to study this transient desensitization problem. Test results revealed reductions in receptor energy output, delayed transitions into detonation, inferior reaction rates, or sympathetic reaction responses from the impaction. Tests on detonators showed reduced tip-strength, abnormal functioning times, or sympathetic firing as a result of transient impaction. The cross-borehole desensitization and sympathetic reaction response problems warrant concern because they are logical mechanisms for raising the risk of hazardous mining conditions, including blown-out shots, flyrock, charge deflagration, and methane/coal dust ignitions.

Jan 1, 1987

By L. Russell Payne

The use of shock tube in the blasting industry is relatively well characterized and understood within the realms to which it is used. Non-conventional uses of shock tube within the EOD and the Aerospace Industry however has not been as widely researched and published. Characteristics of shock tube such as its reliability, simplicity and its non-electric nature make it ideal for functioning or driving mechanical mechanisms, detonators, and timing devices. Outlined in the text are the performance characteristics of shock tube in an array of atmospheric environments including pressures ranging from ambient to 100,000 ft equivalent atmosphere. In addition the useful exit work energy or impulse of the shock tube for driving these various EOD and Aerospace mechanisms is published as a function of tube lengths and atmospheric pressures. Of particular interest to these devices is the required length of shock tube needed to produce the steady state detonation energies and the accompanying properties of the shock tube at these lengths. Various sources publish an arbitrary run distance for steady state detonation and output some where between 20 cm and 1.0 meter. Statistical and experimental evidence with in the text show these numbers to be low and provides an updated reference for shock tubes usage in nonconventional situations.

Jan 1, 2008

By Robert L. Martin, Brian W. Stump, David P. Anderson, David Gross

In an attempt to better understand the impact that large mining shots will have on verifying compliance with the international, worldwide, Comprehensive Test Ban Treaty (CTBT, no nuclear explosion tests), a series of seismic and videographic experiments has been conducted during the past two years at the Black Thunder Coal Mine. Personnel from the mine and Los Alamos National Laboratory have cooperated closely to design and perform experiments to produce results with mutual benefit to both organizations. This paper will summarize our activities, highlighting the unique results of each.

Jan 1, 1997

By Gour Sen, Peter Bellairs

Blasting conducted in rock temperatures greater than or equal to 55°C (13 1 “F) and / or in rock containing sulphide minerals and their oxidation products can result in unplanned detonations. Blasting practices involving the identification of the affected areas together with the use of speciality explosive products and rigorous attention to quality control are required to safely blast in these types of environments. Sulphide dust explosions occur in some underground mines where the primary blast results in a secondary explosion of the sulphide rock dust which propagates some distance from the primary blast area. This phenomena results in considerable damage and the generation of significant volumes of toxic gasses delaying re-entry to the affected area of the mine thereby increasing both costs and safety concerns. The exothermic reaction between ammonium nitrate based explosives and rock types containing partially oxidised sulphides have resulted in numerous high risk blasting incidents. These reactions can occur at ambient temperatures and often result in premature detonations / deflagrations causing a great deal of consternation at the affected minesite resulting in lost production and considerable expenditure to solve the problem. Rock masses at elevated temperatures can also result in unplanned detonations unless appropriate precautions are taken. This paper discusses each of these hazards, cites some case studies and details appropriate generic safe and efficient blasting techniques for each of the above applications using appropriately formulated explosive products.

Jan 1, 2000

By Sergio Segovia Parra, Victor Hernan Sheen Uriol

This contribution of the concept of mass blasting both closing and production allows breaking paradigms, to limit the number of tons to thunder. The areas of geotechnical different mining large mining companies worldwide and especially from the National Copper Corporation (CODELCO, Chile) has been declining volumes closing blasting and production, with the misconception to protect the end walls of the pit, before any geotechnical risks caused by various types of faults; especially the circular faults. A blasting of small tonnage can do more damage to a wall when it is not properly sequenced, leading to the coupling of the wave train and therefore the exponential damage in/s (peak particle velocity, PPV) on the wall of the Tagus. Blasting closing mass production and contribute technically and operationally in the dynamics of the following operations: loading, hauling, crushing, processing and preparation of the final product; eliminating delays to return to thunder small volumes where one must stop all mine equipment, incurring high costs and especially losing valuable time in the continuity of the following unit activities.

Jan 1, 2015

By O E. Jr Crenwelge

Recently promulgated regulations governing blast induced ground vibrations in the mining industry contain a frequency criterion as one option for verifying compliance. This criterion is based upon an oversimplified method which assigns the entire peak particle velocity amplitude to one frequency. Depending upon the nature of the vibration time history, it is possible that this frequency may not even be one of the predominant frequencies of the signal. In addition, the criterion does not specifically define the data analysis approach to be used by the industry for obtaining either the amplitudes or the frequencies of the vibration components. And because personnel in this industry generally have little understanding of vibration phenomena, a number of different approaches are currently being used for satisfying the criterion. This paper presents a method for obtaining both the Fourier amplitude-frequency spectrum and the integrated predominant amplitude-frequency components for the vibration record. The method is both physically and mathematically correct and is in common use in a number of other industries. Therefore, it should be of help to regulators, blasters, and consultants charged with developing, enforcing, or implementing ground vibration criteria.

Jan 1, 1988

By Elias Poulakidas, Marco Arellano

The impact of a higher copper price on the open pit metal mining sector has derived in a faster and safer way in which the mining operation of broken and mineralised material is carried out. In this regard, a good control of bench stability allows a lesser extra removal of material and so more safety to get the planned ore. The stability is ensured through an efficient drilling and blasting, applying the current technology and available know-how. An efficient use of energy through low-density explosives which are the most adequate for the existing solid rock releasing energy in a smoother way through a deterministic detonation sequence which is the application experience presented here. This application experience has two main technological factors; the adequate type of explosive for the kind of rock, in terms of velocity of propagation (Vp) together with the use of a determined detonation sequence and the appropriate designs, which allow to reduce the level of damage to the walls and to maintain a minor backbreaking through quantification with vibration modelling carried out at the near field. The reductions achieved were 30% lower in peak particle velocity.

Jan 1, 2008

By Lina Lopez, Jose Sanchidrian, Jean Du Mouza, Essaieb Hamdi

This paper evaluates the actual energy delivered by the explosives used in the fragmentation of rock during blasting vs. the available theoretical explosive energy. The evaluation of the fragmentation energy of the blast is first done. Fragmentation by blasting can be seen as a process in which creation of new surfaces within the rock mass is made by generation of new cracks or extension of pre-existing ones. From this idea, the fragmentation blast efficiency can be assessed as the fraction of the available explosive energy used for creation of new surfaces. The evaluation of new cracks area created by the blast is based on the SIMBLOC methodology and the corresponding fragmentation energy is then obtained by the Griffith theory. Secondly, the amount of energy delivered down to a certain pressure or volume along the detonation product expansion process, given by the useful work, is calculated. This is done by first determining the CJ state of the reacted explosive and subsequently performing an adiabatic expansion calculation of the detonation products from that state. W-Detcom code has been used for the calculations using the BKW equation of state with the Sandia parameter set. The fragmentation energy and the useful work are calculated for blasts performed in two mines in Spain. Multiple regression is applied to the results in order to give an assessment of the better description of the explosive energy .

Jan 1, 2002

By Miguel Araos

The aim of this study was to understand clearly how VOD of emulsion-based gassed explosives is influenced by parameters such as nitrate salt composition in the oxidizing phase, product density, blend composition, gassing rate, type of sensitization, etc. Also some VOD testing was performed on watergel-based gassed explosives in order to compare the results with those obtained for emulsions. VOD measurements were conducted in the surface blasting facility at the Research and Development laboratory of ENAEX SA (Calama, Chile). Despite the fact that the influences of some parameters on VOD of emulsion-based gassed explosives are easily predicted, there was found to be an unexpected correlation. Although it is commonly believed that the VOD of gassed explosives depends on the density, this study found that the VOD depends on the both size and the amount of gas bubbles incorporated into the product as well as type of sensitisation, regardless of whether the explosive was straight emulsion or a blend. Density is just a consequence of the incorporation of voids into the explosive. Future work in this area may examine variation of other parameters, in order to obtain a greater knowledge of detonation properties and therefore to design more efficient explosives.

Jan 1, 2002

By James H. Redyke

In August, 1980, while finishing construction of the new stack, one of the flues mysteriously collapsed, killing three people and injuring several others. Several months later a British international steeple-jack company was hired to demolish the remaining portion and make a detailed inspection of the balance of the chimney. During this contract almost one hundred core samples were taken from all parts of the structure including the 32-inch thick base. As the result of these tests and the investigation, the Power Company decided to demolish the complete structure. Because of the critical time element, the decision was made to use explosives in the removal of the structure. To give you some perspective as to the size and dimension of the stack, it was 900 feet tall, 80 feet in diameter at the base, and 70 feet in diameter at the top. The two remaining flues were 25 feet in diameter and extended 30 feet beyond the top slab of the chimney. The outside of the structure was referred to as a wind shield. The lower 120 feet were 32 inches thick and the remaining 780 feet were 12 inches thick. The decision was made to prepare and shoot the chimney at the 120-foot elevation because the debris from the collapsed flue was confined in the base section and could not be easily removed. After extensive and costly engineering, we determined it was necessary to construct steel columns to bear on the lower 120-foot section, which would act as a hinge and guide during the dropping of the structure.

Jan 1, 1982

By Y. Hirosaki, H. Hamashima, Y. Itoh Kato, S. Tanaka

The emulsion explosives show non- ideal detonation behavior, and its detonation velocity can be controled by selecting the size and adjusting the quantity of voids involved. To establish the technology to control the detonation characteristics of the emulsion explosives, some experiments have been carried out using resin balloons of five different sizes ranged from O.OSmm to 2.42mm in the average diameter. Detonation velocities of the emulsion explosives containing resin balloons of different size and quantity were determined for the charge diameter of 20-50mm. The detonation velocity at infinite charge diameter was compared with calculated ideal detonation velocity. The emulsion explosives containing large (0.5mm or larger) balloons showed big discrepancy between the measured and calculated detonation velocities, and the fraction of ammonium nitrate reacted in the reaction zone was estimated to be significantly low. It was shown that the reaction zone length was proportional to the size of voids involved. The critical charge diameter was determined for the emulsion explosives containing different resin balloons at the various explosive densities. It is large for the emulsion explosives containing large voids, and it was shown that the critical diameter is proportional to the distance between the void surfaces, not to the void spacing, the distance between the centers of the voids. The reaction rate of the bulk emulsion matrix seems to be the major factor that affects the critical diameter than the specific surface of voids. Good relationship between the critical diameter and the reaction zone length was observed.

Jan 1, 2000

By Chuck Kliche, Bill Clements

This paper relates some of the experiences, good and bad, of blasting adjacent to residences of the primary author during his 15+ years of field blasting in the Northern Great Plains region. During this highly-rewarding blasting career, the author has become aware of two major issues in residential blasting: 1) What we call “Risk/Reward Ratio.”Some questions that must be asked by the blaster prior to taking on any blasting job include: - Can we eliminate or minimize the risk? - Is the reward worth the risk? - Do I have a measure of “nervous confidence” about the shot? 2) Public Relations. Two key elements to public relations are: - Notification - Education All the education in the world to the adjacent populous of what’s happening, of blasting in general, or of what to expect from the blasting does little good without notification. Good public relations is a key to controlling the cost of liability in a litigious society.

Jan 1, 2009

By John Kemeny

There are many methods used to predict blast fragmentation, including empirical and numerical models, field trials, and experience from ongoing blasting. All of these methods require an accurate measurement or prediction of the rock mass properties. These properties include the characteristics of the rock fractures, including fracture density, friction angle, orientation, length, roughness, fill, etc. They also include the hardness of the intact rock, water content, and other parameters. This paper describes three new technologies that can be used to automatically or semi-automatically obtain rock mass properties: digital image processing, 3D laserscanners, and drill monitoring systems. Each of these technologies is described, including the current state of the art, current limitations, and their future potential. Each of these three technologies has advantages and disadvantages. These new technologies, however, have the potential for providing accurate rock mass information in an automated and real time fashion. This information can then form the basis for a new generation of real-time, database driven blast fragmentation models.

Jan 1, 2004

By Josephine Bones, Robb Larson, Daniel Miler

Avalanches are commonly mitigated through the use of explosives at ski resorts and above transportation corridors. Surprisingly, very little research has been conducted on snowpack response to explosive inputs, and efforts to model this response have been limited. The purpose of this ongoing research project is to ascertain an understanding of the dynamic snowpack response in relation to explosive size and height above the snowpack, coupled with snow conditions, to enhance avalanche control. A system of sensors and computer-controlled data acquisition components has been created to record the movement of snow resulting from the charge detonation. The system records acceleration vertically and radially within the snowpack at two distances from the point of detonation as well as blast air pressure at one location during explosive events. The data at two locations allows inferences to be made about the transmittance and attenuation of shock waves through the snowpack radially as well as vertically. The data shows that raising charges above the surface results in increased snowpack dynamic response when compared to surface detonations. Applying power function regression to accelerations for individual charge elevations, it was determined that both radial and vertical rates of attenuation were not dependant on charge elevation. Additionally, raising the charge also resulted in increased dynamic response at depth within the snowpack

Jan 1, 2012

By W. J. Birch, R. Farnfield, G. D. Rangel-Sharp

It is widely recognised that complaints from members of the public relating to blasting operations are related to both ground vibration and air overpressure. It is also known that a complaint is more likely to be generated if the person is inside of a structure at the time of the blast. Reports relating to such complaints often refer to ‘noise’ inside the structure with terms like ‘rattling’ commonly being employed. Such acoustic response is widely perceived within the blasting industry to be directly related to high levels of air overpressure although there appears to have been very little research carried out specifically related to this effect.

Jan 1, 2007

By Jason Baird, Seokbin Lim

Run up is a factor in Linear Shaped Charge (LSC) cutting for which an account must be made. It occurs on the initiation segment of the charge, and the cutting performance during this period is significantly lower. Previous investigations by the UMR Explosives Group observed that similar effects occur not only with LSCs but a wide range of other explosives applications, including explosive-driven flux-compression generators. Prior to this investigation, it was believed that the main contributing factors to run up were from the combined effects of explosive run up (detonation pressure), lack of confinement at the free, initiation end of the charge, and penetrator transition from segmented pieces to a long-rod penetrator blade. As an initial step to understanding the mechanics of LSC run up, a series of investigations was performed in which the testing series was divided into several sub-categories (explosive detonation pressure run up, lack of confinement and long-rod penetrator concept) in order to reveal the effect of each on the run up. Predominantly, commercially manufactured LSCs were used for the investigation, and the entire testing was completed by the UMR Explosives Group.

Jan 1, 2006

By Thomas Leonard, Philip R. Berger, Bryan E. Papillon

Bardon Trimount Inc., a large producer of aggregate, crushed stone, and concrete, was experiencing significant public opposition to its five quarries in the Boston area. It was believed by the authors that this opposition could be significantly lessened if the total number of blasts per week were reduced. Although the blasting company at these quarries, Austin Powder Company, contended that this could easily and safely be accomplished by increasing the size of the blasts, regulations precluded this alternative by limiting the total amount of explosives that could be used per blast.

Jan 1, 1996

By Robert C. Fouchard, Gordon Chalmers, David E. G. Jones, Ivana Alilovic, Phillip D. Lightfoot

There have been numerous international instances over the last several years in which pumping emulsion explosives has resulted in accidents, apparently as a result of increased thermal sensitivity under these conditions. The key questions for the explosive industry are (1) what are the parameters that influence the sensitivity of emulsion explosives and, (2) how do these various parameters interact. To address the sensitivity of emulsion explosives to various parameters, a study was undertaken using an accelerating rate calorimeter (ARC) and a heat flux calorimeter (HFC). The effects ofthe addition of ammonium nitrate (AN) prills and different grades of aluminum (Al) on the thermal behaviour of emulsion explosives were determined. Additionally, changes in pressure, atmosphere (inert or oxidizing) and sample vessel material were assessed for their impact on thermal sensitivity. Addition of AN prills, fine granular Al or atomized Al did not affect the onset temperature for exothermic decomposition, so that the maximum “safe” temperatures for emulsions containing these additives will be similar. There were differences in the rates of self heating, however: AN prills decreased the rate of self heating, whereas atomized Al increased it. The emulsion formulations containing atomized Al produced small holes in titanium vessels. This phenomenon did not occur in Hastelloy C vessels, providing a reminder that materials of construction need to be carefully considered for equipment used to manufacture or handle emulsion explosives.. Both ARC and HFC experiments gave lower onset temperatures in air than in argon. We attribute this to oxidation of the oil phase by air. This result is significant for dry-running pumping conditions, where emulsion is heated in the presence of excess air.

Jan 1, 2000

By B Mohanty

Full-face blasting rounds have been used to excavate a 4.6-mdiameter shaft at Atomic Energy of Canada Limited's Underground Research Laboratory near Pinawa, Manitoba. Both standard pyrotechnic delay detonators and the newly developed electronic delay detonators (EDD) were used on the project. The full-face blasting technique, employing 89-mm-diameter relief holes and 38-mm diameter blast holes, NG-based explosives, and the regular long period delay detonators, has been standard practice at the site, giving excellent wall control and fragmentation results. The comparison blasts using pyrotechnic detonators and EDDs were carried out to test the operational logistics, timing accuracy and blast results obtained with the latter. The long period pyrotechnic delays ranged from O to 18, with the nominal delay varying between 350 ms and 800 ms. The EDD blasts used the same number of periods, with the respective delay interval between successive periods set precisely at 190 ms and 210 ms for the two blasts. Based on a broad range of critically assessed parameters, the EDD blast results proved to be signficantly superior to those obtained with regular pyrotechnic detonators. The results have been analyzed in detail and the relative merits of the two delay systems have been determined. Alternative designs to derive maximum benefits from EDDs in shaft and tunnel blasts have also been suggested.

Jan 1, 1990

By Greg Mclellan, Mark Johnson, John Pepper

Several large quarrying projects recently occurred in Miramar, Florida. These were closely monitored by the Seismologist of Record and Broward County in accordance with County and City regulations. In addition to this monitoring, the City of Miramar employed The Pepper Engineering Group, Inc., to provide additional spot check monitoring and to review the records of the other two parties on a routine basis. Broward County ordinances require that the location of each shot and the nearest protected structure be recorded along with seismograph measurement of each shot at the nearest protected structure. The positions of the blasts and nearest protected structures were determined using GPS. The blast vibrations were measured by seismograph. Over 600 shots, which are the subject of this study, were measured both by the County, the Seismologist and, on many occasions, The Pepper Engineering Group. As such, the vibration data was constantly cross-checked for consistency. The blasting contractor also provided blast designs for each shot. In this paper, the measured vibrations are plotted in terms of Resultant Peak Particle Velocity (RPPV) versus Scaled Distance (SD) on logarithmic scales. The data curves are fitted with least squares and upper 95% and 99% prediction limits are provided. Equations are presented to predict the RPPV based on scaled distance and prediction level using power fits. Statistical information concerning the derivation of the various limits is presented. The raw data used to develop this paper, along with other information concerning the shots, will be posted on the Internet for use by other researchers.

Jan 1, 2000