Search Documents

By William H. Snyer

A relatively inexpensive, very fast response photo-optic/fiberoptic system has been conceived, constructed and employed by Denver Research Institute (DRI) to measure charge breakout uniformity on the surface of a very large ANFO detonation. The new equipment and technique was coined OWL (observation without leads). Its unique design provides the ability to monitor or measure detonation velocities and/or detonation breakout characteristics without fiberoptic or any other direct contact with the explosive. This system has proven to be versatile and has been used to measure surface breakout simultaneity on large ANFO detonations, munition case breakout times and velocity of detonation (VOD).

Jan 1, 1990

By Sri Sawmliana, P. Pal Roy

Blasting Gallery (BG) method was introduced in India for higher production and low cost of excavation to substitute conventional hand section and stowing methods for thick coal seam. The Singareni Collieries Company Ltd. (SCCL) adopted this method in the year 1989 and since then successfully operating at GDK-10, GDK-8 & VK-7 Incline mines in Andra Pradesh, a southern state of India. It is also successful at Chora 10 Pit Colliery of Eastern Coalfields Ltd. (ECL) in West Bengal whereas at East Katras Colliery of Bharat Coking Coal Ltd. (BCCL) in Jharkhand State, the method has been partially successful due to some geological constraints of the area.

Jan 1, 2003

By C Agreda

The Cushion Blasting Technique applied to solve the high risk case history represented by a 10,704 TM rock locate at 120 M from the hydroelectrical plants of 350 KV each, is described, analyzed and discussed. The generation and distribution of 700 KV produced by two hydroelectrical plants must not be interrupted by any reason, because the 26 district of the province of cajatambo, of the Lima department; would not have electrical power. The search of the best alternative and methodology, the drilling and blasting pattern calculations, charge design and loading, connections and initiations of the 50 blasts are described, analyzed and discussed. Finally, the excellent results from a technical, economical, enviromental and safety point of view of the 50 primary blasts are discussed and emphasized.

Jan 1, 2005

By Ruilin Yang

Blast vibration in the highwall from a cast blast in open pit mines or in the hanging walls from a stope blast in underground mines is a common concern. Vibration in such cases is a typical near-field situation where the distance from a blasthole to a point of interest varies significantly compared to the distance between the blast as a whole and the point of interest. Most existing blast vibration models are designed for far-field vibration using a single seed wave to represent all blastholes within a blast and do not simulate wave shape change over the distance. Using the site parameters from the analysis of signature hole vibrations, the present blast vibration model yields reasonable agreement with field measurements in terms of vibration amplitude and frequency. Case studies show that the model has been used successfully to assist field vibration control.

Jan 1, 2010

By Robert Hopler

DESCENT INTO A COAL MINE From “The Playbook of Metals, including Personal Narratives of Visits to Coal, Lead, Copper, and Tin Mines,” by John Henry Pepper. Published by Routledge, Wa rne, and Routledge, London, 1862 ENGINEERING NEWS New Yor k January 22, 1903 THE BEGINNING OF THE END OF DYNAMITE. In another part of this issue we have reported the results of some test results made upon one of the safety powders. It will pay every c o n t r a c t o r, miner, or user of explosives in any form to carefully re a d the article re f e r red to. Dynamite has done a gre a t work in the service of man, as did black powder before it; but its i n h e rent dangers are admitted by all and are proved by the long list of deaths and injuries, and destruction to property which annually occur through its use. Why should we continue to use an explosive that annually kills and maims hund reds of men, when others are available which are equally powerful, no more expensive and far less liable to accidental discharg e ? Dynamite when first manufacture d is pure and comparatively safe; but most unfortunately it does not always stay pure; it “rots,” and then it is exceedingly dangerous. More than this, the explosive part of dynamite is a liquid, nitro - g l y c e rine, which is absorbed or soaked up by sawdust, wood pulp or the like. So long as this liquid nitro - glycerine remains pure and remains “soaked up,” or absorbed t h e re is little danger. It has been found, however, that the nitro - g l y cerine leaks under certain conditions. During thawing it fre q u e n t l y leaks out of the stick, or if it becomes wet the water causes the n i t ro-glycerine to leak out. In either case free liquid nitro - g l y c e r i n e escapes, and in that free state it may be exploded by any very slight shock. Nor is this all, if a stick of frozen dynamite be bro k e n a c ross it has been found by tests that the frozen nitro - g l y c e r i n e w h e re thus broken is very sensitive to shocks afterward .

Jan 1, 2004

By A T. Spathis

The 11th International Symposium on Rock Fragmentation by Blasting (FRAGBLAST 11) was held in Sydney, Australia, between 24-26 August, 2015. The 93 papers, including six keynote presentations, covered exciting and practical topics in 20 sessions within 12 themes. Just fewer than 300 delegates from 27 countries attended. Four workshops were conducted on the weekend prior to the symposium, with three field visits after the symposium to Sydney region quarries, the Hunter Valley coal mining region, and the Kalgoorlie gold mining region. Delegates had the opportunity to visit the exhibition areas that showcased the latest products, software, hardware and systems in blasting technology. The keynote addresses were held in plenary sessions and set the tone for the parallel sessions that followed. They spanned the dynamics of the mining industry, the detonics of explosives, the interaction of stress waves and fracture mechanics in fragmentation, wall control blasting, and the importance of education and engineering for full process optimisation.

Jan 1, 2015

By Ron Ketterling

Donna Summer wrote and recorded a song in 1983 with Michael Omartian called, “She Works Hard for the Money.” The song was inspired by her encounter with an exhausted rest room attendant, Onetta Johnson, who is mentioned in the song by name, and featured on the album’s back cover. ISEE President James Daley, in the May/June 2019 in The Journal of Explosives Engineering discussed the Six Pillars related to the ISEE. We will use the Internal Processes pillar to frame this discussion. The Internal Process Pillar includes five separate sub-committees – we will see how this concept applies to both ATF Explosives record-keeping compliance and business process compliance in general. We will discuss electronic and paper record keeping, what works and what doesn’t. We’ll review record keeping in light of those five sub-committees: Audit, Awards, Constitution, Ethics and Planning. You’ll come away with concrete steps you can use to improve your record keeping processes. This paper will show you how to make the hard work of inventory management and ATF record keeping work hard for you.

I had the opportunity recently to visit a magazine site of a major explosives company. It was fun to see the storage areas again and it was really interesting to see one of the old magazines that probably dated back before my time. Now that’s an old one. As son Tom says, “When Dad was young the Dead Sea was just sick.” While the magazine has been upgraded with a modern lock to match today’s standards it still has the old tumbler lock that is opened with the large bronze key. Those old tumbler locks were just about standard on magazines years ago. Those bronze keys were heavy and would make a good display item today or maybe a substitute for a blackjack. I don’t think the old locks would stop the modern criminal but then in those days we were all less sophisticated. And maybe I shouldn’t say this but honesty was a bit more prevalent then. Maybe ‘cause old fashioned police brutality still prevailed.

Jan 1, 2004

By Jay Rodgers

There has been a longstanding acceptance that burden plays a major role in the magnitude of ground vibration amplitudes generated from surface blasting. Much of the data that this belief is based upon is empirical in nature and may or may not represent an example of false inference. Recent published reports have rightly questioned the influence of burden and confinement on blast vibration amplitude, suggesting that the fracture condition of the rock mass is a better indicator. The increased investment in electronic detonators as a tool to control ground vibration amplitudes demands an understanding of vibration production detailed enough to make use of the vastly improved timing accuracy that they provide. A more accurate relationship may be found if we strip away the assumptions of the past and search for the underlying mechanism of vibration production in surface blasting. We must answer the question: What happens at or near the borehole when an explosive charge detonates that produces ground vibrations?

Jan 1, 2003

By Mike Lovitt

New Gold Inc. had commissioned Orica to assist with the design of the drawbell blasting at New Afton Underground copper/gold block cave at Kamloops, British Columbia, Canada. Orica have had much success in developing the single-shot drawbell method at Freeport Indonesia in 2001 in the Deep Ore Zone and they will be using it exclusively in their new Grasberg Underground Operation. RioTinto Northparkes have also used the single shot drawbell blasting in their Second Lift E26 Project and even in the E48 orebody which is a post undercut block cave, realising the safety and operational benefits of this blasting method.

Jan 1, 2013

By Ajoy K. Singh, B Mohanty, P K. Singh

A study was conducted to investigate the damage potential to underground multiseam openings caused due to vibration generated by open-pit coal mine blasting. The objective was to recommend optimal explosives weight per delay to be detonated in open-pit blasts to ensure the safety and stability of underground openings. Sixteen blasts with varying charge weights and initiation sequences were conducted at Samleshawari open-pit mine and eighty four blast vibration data were recorded in the Hingir Rampur underground colliery in India. Analysis of vibration data showed that roof of the underground openings vibrated with much higher amplitudes compared to those in pillars and floors. The amplifications of vibration in the roof at the junction were upto 4.3 times the pillar vibration. It was observed that coal chips detached from roof when the peak particle velocity reached 131 mm/s or higher. The vibration magnitude recorded was higher in upper-seam openings than in belowseam openings. Rapid attenuation of vibration was recorded in below-seam openings at similar locations. Appropriate particle velocity-charge weight-distance equations were established to calculate the safe explosive weight per delay to be detonated in open-pit mine for the safety of multi-seams workings of underground mine. The support for the galleries and junctions were further modified for the working seams to ensure greater safety.

Jan 1, 2011

By Rob Domotor

This paper tells the story of using controlled surface and underground blasting methods to excavate hard rock in three areas on Australia’s largest road infrastructure project; the Airportlink Project in Brisbane; worth a total value of AUD $4.8 billion. The project used blasting methods including design, modelling, drilling and loading of the explosives that had never been used before in Australia, some of these were probably unique in the world.

Jan 1, 2012

By Gabsoo Kim, Rulin Yang, Dave Kay

Blast vibration data, such as PPV are usually scattered. In many cases, plots of PPV versus the charge weight scaled distance are so scattered that useful trends from different blast designs cannot be identified. The scattering of the data may be attributed to the inaccuracy of the PPV measurement, the definition of the scaled distance from a multiple-hole production blast, and the measurement of distances and charge weights. The error from vibration measurements is one of the major contributors to the scattering of the plots. If accurate monitoring is conducted, improved design options may be identified. This paper documents two case examples that compare different vibration sensor couplings. The first case shows mounting accelerometers at spots that protrude from the ground, compared with the sensors that were mounted on a flat ground surface. The second case compares data from loose-sand buried geophone with that from sensors coupled to the ground using concrete blocks.

Jan 1, 2014

By Alan: Moore Richards

Effective control of airblast requires that significant factors be identified and satisfied by blast design and careful implementation. Significant factors include charge mass, distance, face height and orientation, burden, spacing, and initiation sequence, stemming height and type, topographical shielding, and meteorological conditions. This paper utilizes case histories of blasting in Australian open pit mines to demonstrate techniques that have been used to control airblast to applicable limits.

Jan 1, 2006

By Wang Xuguang, Zhang Xiaozhi, Li Guozhong, Xiong Daiyu

The emulsion explosive is a new kind of water-based industrial explosives that was developed at the end of 1960s. In the 1970s, BGRIMM invented EL-series emulsion explosive that created a new era of water-based industrial explosives technology and products in China. From single type to varieties, the perfect BGRIMM emulsion explosives technology has been formed, which consists of 9 series, over 30 types explosives and related production equipments and processes such as cap-sensitive rock emulsion explosive, opencast emulsion explosive, coal permitted emulsion explosives, low-temperature-resistant emulsion explosive, high-temperature-resistant emulsion explosive, high power emulsion explosive, bulk emulsion explosive for loading truck and powder emulsion explosive. From the early 1990s, BGRIMM successfully developed opencast emulsion explosives and the computer controlled continuous production line of small-diameter cap-sensitive emulsion explosive which raised emulsion explosive production technology of our country to a new lever. With the successful development of powder emulsion explosive and related computer controlled continuous production line, on-site mixed emulsion explosive and loading truck as well, the category of industrial explosives is getting more complete and reasonable. This paper pres ents the history, achievement and development of BGRIMM emulsion explosive technology, also forecasts the future of linked technology.

Jan 1, 2003

By Brad H. A Brown, J Paul Tidman

To design a blast, one must give consideration to safety, economics, geometry, geology, production needs, and a variety of other requirements. To compare designs requires the time to develop alternatives, analyze, and then improve on them. A number of tools are available to assist with the first set of requirements, however they are poorly integrated. SHOTPlus is a program to improve the efficiency of blasting operations, by combining measurement and blast design tools, and offers the user the time and means to modify designs and explore alternatives.

Jan 1, 1997

By John Capers

•The IME is the Safety and Security Association of the commercial explosives industry in the United States and Canada. •Founded in 1913 •Board of Governors •5 Standing committees- 1. Technical 2. Environmental Affairs 3. Legal Affairs 4. Safety & Health 5. Transportation & Distribution

Jan 1, 2006

By Enver Alan, MerkeziYapı

People are migrating because of economic, social, natural and political reasons. These natural and humane factors effects the distribution of populations. The need for tunnels has grown in order to provide a comfortable life and reduce losses such as waste of time, labor, energy, efficiency and so on. It is inevitable to carry out excavations in rock tunnels (shears, platforms, lines, connections, wastewater, distribution, energy, transportation etc.), that will be built by excavating with conventional method, by controlled blasting regarding with constrains. In this study of applied explosives engineering the blasting applications are evaluated, which were carried out for research and development purposes at Yenisahra Station tunnels in Kartal Formation which was built with the aim of solving İstanbul's transportation problem within the framework of the Kadıköy-Kartal Metro Project. Twenty-four shots were made by using explosives in 60 blastholes that were drilled in the tunnel faces, which were located between and outside of two different faults. Six microphones were used to measure the air shock and eight geophones were used to measure the parameter values of the vibrations (particle velocity, frequency, displacement, acceleration, amplitude, wavelength etc.), which were placed at predetermined points of the surface, occurred during the blasting applications. Data from the geophone and microphones were recorded on six seismographs. The coordinates and the distances between the shot points and the measurement stations are determined by an electronic theodolite. The total number of seismic records, recorded in seismographs, is 118. The number of records of vibrations that crossed the faults is 42 and the number of records of vibrations that did not cross the fault is 76. The particle velocity, frequency, amplitude, acceleration, displacement and wavelength were measured in transverse, longitudinal and vertical directions. The total number of measurements is 354. By evaluating all seismic records, the effect of delay intervals, faults and scaled distances on the particle velocity, frequency, amplitude, displacement, acceleration, wavelength and air shock were investigated. When the vibrations formed during the Research & Development (R&D) blasts were examined, it was determined that the parameter values of vibrations that crossed the faults are lower than the ones that did not cross the faults. In addition, when the particle velocity values of all vibrations are examined according to the present circumstances, it is determined that the waves did not cross the fault in all delay intervals are superposed in all directions, and that the least superposing occurred in the 50 ms delay range.

By Conny Postupack

To make money in mining coal you have to sell it for a lot more than it cost you to get it out of the ground. And yet, every year it cost us more and more to stay inbusiness, while the price we get for coal does not increase at the same rate.

Jan 1, 1990

By Douglas Bartley, Jay Elkin

The state of Pennsylvania was at one time one of the leading coal producing states in the east. However, legislation and industry trends over the last 10 years have adversely affected the amount of bituminous coal mined in Pennsylvania and the whole eastern United States. The application for and approval of a new mining permit is a very costly and arduous task. When a new mining operation is established it is crucial that nothing within the operator’s control causes the operation to stop producing. This paper discusses the action taken by a small mine in Pennsylvania when their blast induced vibrations rose to levels that typically would have resulted in a total mine shut down by the regulatory body governing such operations.

Jan 1, 2003