Search Documents

By Rapheal Trousselle

For over 5 years, Davey Bickford has been developing and testing an electronic detonator blasting system. These new-technology detonators provide more accurate timing than conventional systems that rely on the combustion speed of a pyrotechnic composition.

Jan 1, 1997

By Michael Mann

Two house trailers and a modem modular house, all pillar-supported with cantilevered perimeters, were monitored for structural response to vibrations from surface coal mine blasts. Due to the large blast site distances, peak particle velocities measured in the ground beside the houses did not exceed 0.32 ips, and airblasts did not exceed 106 dB. However, the structures responded significantly to the ground vibrations, with maximum high-comer amplification factors as high as 8.5 in the horizontal directions. Vertical structural responses were as high as 10 times the vertical peak particle velocities in the ground, but appeared to be driven more by horizontal ground motions. No measurable airblast responses were observed. The natural frequencies of the structures ranged from 5 to 10 Hz.

Jan 1, 2000

By Sang Ho Cho, Masaji Kato, Masaaki Yamamoto, Masaaki Nishi, Katsuhiko Kaneko

This paper presents a numerical simulation method to predict rock fragmentation and to verify a fracture mechanism by bench blasting. The rock fragmentation, which has been used as a means of the index to estimate the effect of bench blasting, affects the expenses for loading, conveyance and crushing of blasting muck piles. The developed numerical simulation method is based on the finite element method and fracture mechanics and includes the re-meshing procedure to express the fracture process of the rock mass. This paper discusses a procedure for a determination of size distributions of the results, which were calculated by numerical simulation, including the tines.

Jan 1, 2002

By Paul Downing

A typical day for a blasting company includes what seems to be an infinite list of tasks dealing with numbers. Whether determining the exact amount of explosives material in inventory, the number of holes in the shot, the exact distance from the blast site to the nearest exposure, or the capacity of bulk hoppers, the accuracy of numbers is key to ensuring the safety of the public, property and personnel.

Jan 1, 2008

By Mike Boissonneault

It was three years ago when the “storm of the century” had taken a firm grip over the Pacific West Coast and inland areas. At the Big Sky ski resort in Montana on Christmas morning two ski patrollers set out to perform an explosives “hand charge” avalanche control mission that would see only one return. It has been difficult to determine exactly what happened. Investigators do know that there were three separate and consecutive attempts to light a safety fuse, when it had apparently been burning since the first attempt. Time ran out after the third attempt. Although this accident has had a profound impact on North American avalanche control programs, I am sure it pales in contrast to the shock and grief experienced by family members who lost a loved one.

Jan 1, 2001

By Adam Gray, Emery Gray

State-of-the-art seismographs can be employed to assist the blasting engineer in understanding the propagation of vibration waves generated by blasting. Wave traces and frequency plots are used to adjust shot loading and timing, especially around close or near- field structures. Successful close-in blasting vibration monitoring requires careful consideration of the following: Geophone locations Mounting of geophone both on structures and in the ground Differences between ground motion and structural response This presentation will discuss methods used to control and monitor blast-induced ground and structure motions. Case histories are presented to illustrate seismic monitoring used as a tool to control vibrations and guide the blaster in the design process.

Jan 1, 2005

By Larry Schneider

I n the simplest application of a shock tube initiation system, the tubing acts as a “relay line” which passes a detonation signal from borehole to borehole. When the signal arrives at each borehole, it causes the detonator attached to it to fire. Such a single path constitutes a progressive series where each unit must function properly in order to activate the following units. Any application error, malfunction, or mistake in connecting any surface unit will stop the progression of the detonation signal through the system and result in a “cutoff” or misfire of the following charges.

Jan 1, 1995

By Robert Lee, Jeff Corace, Rob Cyr

Blasting in the heart of the historic Byward Market District of Canada’s capital, Ottawa, presents a unique set of challenges. The obvious difficulties arising on projects requiring blasting within 3 m (10 ft) of 125 year old buildings in various states of disrepair have been encountered and successfully dealt with countless times before. The complexities increase exponentially when tenuous property boundaries, unknown structural details, litigious histories and the need for encroachment agreements lead to individuals with competing interests all able to impact the same operation. Blasting on three projects in the Market was started in early 2005 after months of negotiation. Ultimately, the potential for the projects to proceed hinged on the ability to successfully disseminate blast data to the various stakeholders. As part of the agreements drawn up, property owners demanded immediate notification of the measured vibration levels with contract provisions including clauses such that any exceedance of the USBM criteria immediately triggered project shut down and complete blasting program redesign, and approval by all parties. With stakeholders located in various cities and, in some instances, on various continents, a conventional attended monitoring strategy would not satisfy the requirements. In response to the critical reporting need, Explotech Engineering Ltd. installed unattended monitoring stations around the sites, all incorporating wireless telemetry. After each blast, data was automatically transferred from the monitoring stations to a web-linked server via the wireless network, where it was immediately available to project stakeholders through a password protected website. The solution required a unique blend of data acquisition, telemetry, database, and security technologies, all married to produce a reliable system that was easy to maintain and use. While these types of systems were originally developed for use as permanent monitoring networks in operating mines and quarries, monitoring professionals are increasingly benefiting from the technology on temporary building projects that have typically been the realm of attended monitoring strategies. Globally, this has emerged as a solution to provide more timely access to data for stakeholders, and to minimize the legal exposure from multiple violations of vibration limits. As this trend is likely to continue, the regulated vibration control industry is likely to see a continued shift in technology development to leverage wireless networks and the Internet to continue to improve data transfer, archiving and distribution.

Jan 1, 2006

By Anthony J. Konya

"This paper was written during part of the author’s student co-op with Cargill Salt at its Avery Islandunderground salt mine in Louisiana. Blasting salt is a unique type of blasting that is different than blasting other rock types. The plastic nature of salt, along with its large swell factor make salt a challenge to blast. The Cargill salt mines use and have tested a variety of different methods for breaking salt in an efficient manner, however these blasting methods are rarely used in other operations nor talked about today."

Jan 1, 2016

By John Watson

New Technologies, New Challenges and New Opportunities For quite some time now, numerous explosive manufacturers have spent untold man-hours and millions of dollars trying to develop a blast initiation technology that would “once and for all” provide users with what was once believed to be only a theoretical possibility...nominal timing. Zero “cap scatter” (the amount of variation of delay timing from the targeted nominal) has been the industry’s goal ever since delays were first introduced into the marketplace. Just as adding delay time between blast-holes improved blast performance since their introduction, having the wrong delay or a poorly timed blast has proven to be very inefficient and in many cases hazardous. The question of how precise a blast initiation system needs to be still remains unanswered, but electronic detonator systems being used today indicate that significant improvements can be achieved over conventional pyrotechnic detonators. These systems can typically provide single digit millisecond ranges of variability, if not sub-millisecond in some cases.

Jan 1, 2003

By Alex Chapman, Cam Thomas, Bryan Karney

"During the early summer of 1989, Ontario Hydro removed a concrete portion of the North Channel Dam at Crystal Falls Generating Station by blasting and excavating in marine conditions. Because of the severity of underwater blasting and because the site was in close proximity to the replacement dam, there was concern that hydraulic shock waves generated by the detonation could damage either the new dam or its control structures. This paper examines the data associated with the hydraulic shock waves generated by underwater blasting, and studies the effectiveness of an air curtain in reducing the peak pressures. In previous trials using the air curtain technique, a rule-of-thumb factor was used to estimate that only 10% of the original pressure pulse would propagate across the air curtain. However, this value had little basis in theory. A theoretical formulation of the problem by Karney in 1989 indicated a provisional value of 0.18 for this factor, but was heavily dependent on confirmation from in-field testing. Data provided by Ontario Hydro from an actual blasting procedure indicate that a more conservative value of 0.32 may be more appropriate. Thus.although the air curtain did provide considerable reduction of peak pressures, the data at Crystal Falls indicates its performance was below the anticipated level. However, due to problems with the instrumentation and some inconsistencies in the resulting data. it is recommended that this value be further refined as additional data become available."

Jan 1, 1992

By W B. Gregg

The rock blasting and mining industries use a system of detonators and explosives for mining operations. Many detonators use small metal bridgewires, which are heated by passing a current through the wire, heating and igniting the pyrotechnic powder in contact with the wire. Typical bridgewires require a current of at least 3 amps, applied for a few milliseconds, for an explosive output. The semiconductor bridge (SCB), in comparison, initiates an explosive in 0.01 to 0.1 of a millisecond.

Jan 1, 1994

By Steven Putt

Seismic While Drilling (SWD) is a newly developed technology in the mining industry. Improving upon Measurement While Drilling (MWD) systems, SWD measures mechanical properties of the rock at incremental depths down a blast hole at a much higher resolution. SWD is also immune to common failures and inconsistencies of MWD such as operator and drill specific variation. Seismic While Drilling records the velocity and elastic modulus of the rock with centimeter accuracy in real-time. These properties measured while drilling blastholes are then used as a proxy for density which can be used for: • High resolution geologic modeling • 3D ore control • Drill and blast optimization • Drill to mill tracking One of the distinct challenges with SWD systems is the sheer volume of information acquired. With thousands of measurements per blasthole, the data can be overwhelming for even an experienced engineer. To overcome this complex challenge, the latest cloud computing and analytics models have been simplifying and organizing the data. These newer technologies can amplify an engineer’s capability by delivering actionable insights into their drilling and blasting workflows. The paper presents new results from Datacloud during recent Seismic While Drilling trials in iron ore, metallurgical coal, and hard rock mines around the world. The measurements are compared with wireline geophysical logs, core data, drill cuttings, and conventional measurement while drilling (MWD) systems to validate the technology and show how the data can be used.

By Stuart Brashear, Eddie Colburn

The Birmingham Coal and Coke – Knight Mine is a single seam coal mine in central Alabama. As pit development progressed in 2013, concerns over increasing vibration levels resulted in modifications to the blasting program that inhibited shot size and coal recovery. By January 2014, while still over 1,400 feet (427 m) from the regulatory seismograph, vibration levels climbed above 70% of the mine permit limit, even with triple decking of holes and reduced burden and spacing. At this time the decision was made to commit to the use of signature waveform analysis and precision programmable electronic detonators to minimize vibration and maximize the amount of coal that could be recovered before vibration levels reached permit limits.

Jan 1, 2015

By Nolan Eckroade, Nigel Pereira

Wireless electronic blasting systems are a new technology that enable truly wireless initiation through rock, air and water. This is achieved using low frequency magnetic induction waves to wirelessly send a firing command to groups of in-hole primers. Fully wireless initiation not only removes the limitations imposed by a wired connection to each primer in a blast, but also enables users to alter the paradigm of conventional mining techniques to advance operational productivity and reduce personnel exposure to high-risk activities. While initially deployed in underground applications, wireless electronic blasting is now being used in the open cut environment. To capture the early impacts in surface mining operations, case studies conducted at three surface mines evaluated blasts utilizing a wireless electronic blasting system against baseline blasts using conventional, wired initiation systems. The purpose of this paper is to outline the specific learnings associated with wireless electronic blasting in surface mining to date. The paper will include references to these specific case studies as well as benefits realized and applications for the future.

By Agne Rustan

The 9th International Symposium on Rock Fragmentation by Blasting was held in the Granada Conference Centre, Granada, Spain from the 14th - 17th September 2009. The Symposium was preceded by a 1 ½ day Workshop on “Vibrations from Blasting” organized by the initiator Dr. Alex Spathis and his colleague M. J. Noy, both employed at Orica Mining, Australia. Prof. Josè Sanchidrian at the “Universidad Politécnic de Madrid” in Madrid, Spain was the main organizer for both the Workshop and the Symposium. A record number of participants came (292) from a record number of countries (41). There were a total of 14 papers in the Vibrations from Blasting Seminar and 96 papers and 2 Keynote Addresses in the Fragblast 9 Symposium itself. The aim with this paper is to present some results from Fragblast 9 which are of interest for a large target group. One very important result from the Fragblast 9 meeting was that it was decided there that Fragblast 10 will be held in November 2012 New Delhi India.

Jan 1, 2009

By J. Lindenau

One of the significant benefits of electronic detonators is their safety, especially their relative insensitivity to extraneous electrical energy. The various brands of electronic detonators on the market have different resistance to electrical stimuli, but all have safety structures designed to afford a significant level of protection. A common source of extraneous electrical energy is lightning. This paper discusses the nature of the energy that occurs with a lightning strike and the resistance offered by electronic detonators. Four actual cases of exposure of electronic detonators to lightning strikes are considered. Electronic detonators, like other initiation systems, are vulnerable to very close or direct lightning strikes. The incidents are a reminder that all blast patterns need to be vacated on the approach and during the progress of a lightning storm. 1. Orica

Jan 1, 2008

By William Reisz

Over the years as surface mining operations have become more sophisticated, angle drilling has become a more popular blast design technique, especially in areas where overburden and stripping ratios have increased. Another method of blast design is the staggered pattern, which greatly improves explosives distribution within the blast. While both methods present some engineering challenges, this paper will discuss how the two methods can be combined to enhance fragmentation, improve cast percentage, drill production ratios and highwall control. A practical engineering approach will be presented as well as a discussion on the discipline required to maintain a quality blasting plan.

Jan 1, 2002

By James W. Reil, Douglas A. Anderson, Steven L. Burchell

A total of 26 full-scale production blasts at three sites were extensively monitored with sophisticated instrumentation systems to determine the benefits of more accurate detonators. The new and more accurate MS electric Masterdet detonator was tested against conventional detonators to determine any increase in productivity outputs. All blast design parameters between paired blasts were kept as constant as possible with the only difference being the inherent accuracy of both detonator systems.

Jan 1, 1986

By Jack Eloranta

This paper documents the relationship between material handling and processing coete compared to blasting cost. The old adage, "The cheapest crushing is done in the pit", appears accurate in this c!ase study. Comparison of the accumulated cost of: powder, selected wear materials and electricity; indicate a strong. inverse correlation with powder factor (lbe powder/long ton of rock). In this case, the increased powder cost is more than offset by electrical savings alone.

Jan 1, 1995