Search Documents

By Thomas E. Ricketts

Occidental Oil Shale, Inc. constructed two commercial-sized modified in situ (MIS) retorts, Retorts 7 and 8, at its Logan Wash Oil Shale Mine in February and April 1981, respectively. One of the primary objectives of this two-retort program was to examine large-scale blasting reproducibility for commercial-sized retorts. The blast design used 545 blastholes and 550,000 pounds of explosive in ANFO equivalent per retort. Each retort was blasted using millisecond delay blasting caps tied into a single round. The blasts resulted in rubble beds very close to one another and to predicted results obtained using newly developed limited void blasting technology. The heights of the remaining void rooms over the beds after blasting were within 0.3 feet of one another. This excellent reproducibility is brought into true perspective when compared to the scale of the rubble beds which were 230 feet high with volumes of over six million cubic feet each.

Jan 1, 1984

By Jason Baird, Braden Lusk, Dominique Nolan, Allen Stults

Conical shaped charges have been used to penetrate rock for many years now. Examinations have been made looking at shaped charge liner geometry, material, and standoff, as well as explosive composition, confinement and initiation. Most of the testing conducted towards penetration rather than cratering has fallen within the realm of the petroleum industry and as such been confined to specific rock types, with test apparatus that include simulated down hole (subterranean) environments. The testing conducted within this experimentation is conducted at ground level, in small scale samples, using a single standoff, against multiple rock types. The data collected from that testing is examined here and relationships between physical properties of the rock and the liner are analyzed. The analysis of that data raises the possibility of a relationship that may lead to new empirical methods of penetration prediction in rock.

Jan 1, 2012

By L. Wilson, M. Kotzel, T. Pienaar

An empirical equation is presented for the maximum airblast from unconfined charges. This has been tested at a number of sites and with charges ranging from 0.1kg to 311kg. The equation is developed to predict community response to potential explosive test range sites and the testing has added to our knowledge of the effectiveness of mitigating measures. The first site had 10m to 15m high walls that were intended to ameliorate the airblast. These walls functioned to a limited extent and reduced the airblast levels by 2dB to 5dB. The airblast was affected somewhat by topography. Noise levels at the nearest residences exceeded 130dB for charges larger than 1kg, whereas the vibration levels were very small. Formal complaints were received where the airblast level exceeded 128dB as per conventional expectations. Pedestrians and pets in the suburbs were startled by the blasts, emphasizing that the community response is much more sensitive to noise and airblast than vibration levels. The maximum airblast levels were too high for this site to be used on a regular basis. At another site, the airblast levels were significantly increased downwind by up to 10dB due to a moderate wind. A third site, at a quarry, produced unconfined airblast levels beneath the derived limits, but are much higher than the normal quarry blasting. By involving community forums there were no complaints, possibly due to desensitization by the normal blasting activities. The study has highlighted new areas for research in understanding the effect of noise, air blast and vibration on the low cost and informal housing typical in South Africa

Jan 1, 2011

By Steven Richardson, E A. Cameron, Reza "Ray" Jambakhsh

This paper outlines the design and implementation of a method to use Long hole Carbide drilling to blast an "Upper Blind Slot Raise" in the range of 12m (40 ft).

Jan 1, 1992

By Italo Onederra, Miguel Araos

"Most of the current explosives for mining blasting activities are based on ammonium nitrate (ANFO, emulsions and watergels). AN-based explosives’ detonating properties were discovered in the 50’s and since then they have proven to be reliable, safe and cost effective. However, there is no current alternative raw material to replace AN. As part of a program of research initially funded by the Australian Coal Association Research Program (ACARP), Mining3 and the University of Queensland engaged in the search for potential oxidizing agent alternatives that could replace AN in the manufacture of mining explosives. Candidates included those that are produced in large quantities and that can be cost competitive with ammonium nitrate. The initial work identified hydrogen peroxide (HP), calcium ammonium nitrate (CAN) and sodium nitrate (SN). Explosives mixtures were prepared and sensitized using void sensitization techniques. The detonation properties results showed that explosives based onmixtures of HP/CN and HP/SN as the oxidizer were able to detonate in a range of 2000 – 5000 m/s, indiameters 50 and 102 mm, and densities in the range of 0.50 – 1.40 g/ml. Although more studies need to be conducted to fully understand these explosives, if successful, these explosives would be able to offer an alternative to the AN-based explosives in the mining industry."

Jan 1, 2017

By Matheson and Miller

Does anyone have any definitive information on vibration limits for damage to well casings near blasting? Also, are people using self-imposed limits when approaching cased wells? I can only tell you what I have personally done with success. Often in new construction in hard rock, the well is drilled before the foundation is excavated and before the ditch for the water line is excavated. These both require drilling and blasting. Under these circumstances when blasting for the ditch for the waterline we will drill right up to within 10 inches (not feet) of the well casing. We drill line holes the width of the ditch, then about a foot from this, another row of trim holes then as we move away from the casing holes for 1 1/4 inch stick powder for about three rows then as we get further still, we can load with ANFO. I do not have vibration data for this but my experience has been that as long as you are not displacing the material into the casing that no damage is done. These typically are steel casings for residential water service.

Jan 1, 2010

By Robert Boehnke, Bernd Mueller

This contribution presents an innovative, statistically supported method to predict blast vibrations in rock mass. For modelling the processes during and after detonation, a theory is employed which is based on linear momentum (so-called momentum theory), strongly supported by new measurement methods. During the course of the investigations, the following parameters have been found to dominantly influence vibrations: ! charge WB, includes geometrical factors such as borehole length and diameter (kg) ! detonation velocity cd of the explosives used (m/s) ! distance r between the points of emission and immission (m) and the statistically determined negative exponent n ! factor RM or RS of the rock mass which is related to the specific blast momentum and the drilling and blasting technique used and is statistically determined together with the exponent m (mm/kg or mms/kgm)

Jan 1, 2004

By Vitor Barcelos, Eduardo Elói, Gabriella Vaz, Davi Oliveira, Leandro Silveira

Following a routine production blast at Vale S.A.'s Itabira Mine in the Quadrilátero Ferrífero region of Minas Gerais, Brazil, nearby residents registered complaints about blast-induced vibrations. Analysis of the blast footage revealed that multiple blastholes were detonated simultaneously, resulting in a higher-than-expected charge per delay, ground vibration and cratering even though the electronic delay timing was configured correctly. Subsequent blasts within the mine's soft schist region confirmed the occurrence of sympathetic detonation. Mitigating or eliminating this phenomenon is critical for the mine's operation. Two dynamic pressure tests were conducted using carbon resistors together with typical VOD monitor maintaining the standard booster, electronic detonator, and a blend of 70% emulsion with 30% ammonium nitrate explosive. The tests involved increasing the distance between the central hole (detonated first) and the four surrounding holes in a five-hole sequence. Unfortunately, sympathetic detonation occurred in all these tests. To address this issue, a new explosive with a lower density and detonation velocity was tested. This approach proved promising, as no sympathetic detonation occurred. By leveraging the data obtained from this study, engineers can now identify situations at risk of sympathetic detonation and implement preventive measures, such as selecting the appropriate explosive and recommending safe minimum burden and spacing settings as well as confinement level for each blast while maintaining the desired level of rock fragmentation.

Jan 21, 2025

By Carlos Alvarado, Hernan Narea, Jhon Silva, Bryan Townsend, Katherine Gil, Brayan Caceres, Felipe Pontanilla

With the promising development of new technologies, automation in Drill and Blasting (D&B) is on the horizon. The data generated in all D&B activities, which is currently segregated, can be linked to become information and carry a logical meaning. This information can be used to identify critical activities and make decisions regarding corrective measures to accomplish the goals of D&B. Minera Caserones, supporting Alert2Gain (A2G), and Dyno Nobel, has been working on the development of a quality assurance and quality control (QAQC), system for the mine involving all D&B activities. The main variables in the model for D&B include data from the geology of the deposit, drilling, explosive products, and material loading, among others. To create the model, the mine is divided into blasting polygons. Those polygons are part of a block model. The block model is assembled following different rules, such as: • Block sizes of 4m x 4m x 15m, • Classification of the blocks to a particular blasting polygon using a geospatial intersection algorithm, • Algorithms connect all the pieces of data automatically with the minimum of human intervention and populate the block model, Because measuring data for each block is impossible, another set of rules and algorithms completes the model. Dyno Nobel generates an essential set of data for the QAQC system. Explosive truck loading rates and explosive products, among other data, are also included in the system. The system autogenerates reports every hour, and a summary of the results of each mining day (a mining shift of 12 hours) is distributed by email to all responsible persons to identify the critical tasks and then to make the proper adjustments to accomplish the goals of D&B. The information is updated every hour and available through a dashboard for easy and straightforward interpretation. This paper explains the conceptual details of the QAQC system implemented in Minera Caserones, how the data is aggregated automatically from the different sources, shows examples of the type of information in the dashboard, and presents a successful case where a deviation was detected, and the corrective measures that were implemented to keep the performance of the D&B activity. The paper finally discusses the next steps toward an autonomous D&B system based on new AI technologies, with minimum human intervention.

Jan 21, 2025

By Ali Kahriman, D. Adiguzel, R. Ulger, U. Akkaya

The environmental problems arising from ground vibration has been faced and discussed frequently in various industries such as quarry, mining, civil works, shaft, tunneling, pipe line and dam construction etc. where the blasting operations are unavoidable. This paper presents the results of ground vibration analysis induced by blasting during the construction of the Istanbul Kadiköy-Kartal metro tunnel. Different rock formations in this tunnel route which is 21.6 km in length were encountered during the excavation process by blasting. As a first stage, Hoek’s Geological Strength Index (GSI) values of rock units were determined by using inverse distance weighting method. The GSI values which were obtained from boring data were used when evaluate the data. GSI values were estimated by inverse distance method (figure 3) along with the tunnel route. Afterwards, ground vibration parameters induced by 21 shots which were made in different locations was monitored and passing routes of vibration waves determined. Weighted averages of GSI values were calculated according to distance of the regions where vibration waves passed. Multi regression analyze were made with using frequency, charge per delay, GSI and the distance between the shot point and monitor station. The main goal of this study is to investigate the relationship between ground vibration frequency induced by blasting and GSI.

Jan 1, 2011

By Christopher Jon Preston, Troy Williams, Daniel Roy

There has been significant progress made with narrow vein gold mines in which a second option for crushing has begun to attract attention. To ensure the profitability of a mine that has based its economics on the absence of a crusher station, more than just best blasting practices are required. Using a blasting operation itself as a primary crusher would undoubtedly save enormous capital costs as well as eliminate some of the costs of crushing ore with the result that considerable savings might be realized. The challenge would be to define the conditions necessary to make this type of operation feasible by providing consistent blasting methods that result in a significant paradigm shift with respect to both blasting and current underground crushing methods. A break model has been developed and applied as a technique in designing blasting patterns based on a unit charge blasting geometry and stress reflection from free faces. There are four components to this model and these are 1) unit charge, 2) thermodynamic/energy, 3) stress reflection, and 4) radial break. Some important changes in timing between holes and rows based on rock properties and the percentage of burden moved were also used. On-site testing at a narrow vein gold mine in Quebec Canada, provided measured parameters for the model. No underground crusher was planned - relying only on the fragmentation profile generated by ring blasting. The specification for muck was that the fragmentation profile needed to be 100% < 400 mm (16 in) with no overbreak - with dilution less

Jan 1, 2019

By Paul Worsey, Gillian Worsey

Description of Project:The basic blasting class underground lab at the Missouri S&T experimental mine in Rolla, o., shows the students how to drill, set up, load, and shoot a shot underground. In this case the shot was part of a new ramp to a second level.

Jan 1, 2014

By Ron Woolf, Corry Goumans

With increasing traffic volumes experienced thro u g hout North America, a common goal for Highway officials is to keep traffic flowing as much as possible and to keep disruptions to the flow to a minimum. Our experience throughout the US and Canada has shown that all Departments of Transportation are under extreme pressure from the private sector to keep highways open for various reasons, convenience and revenue being the most common. For example, on Highway 99, from Vancouver, BC to the Whistler resort area, local merchants, homeowners and ski hill operators exert extreme pressure on the Ministry of Transportation to keep the highway open, and in Pennsylvania, the Turnpike Commission requires traffic to flow on a continual basis. Loss of revenue in these two cases is the main impetus to keep the traffic moving.

Jan 1, 2003

By Roger G. Sprague

With the passing of time, changing marketplaces and years of hard service, coupled with new machines, increased productivity, rapidly improving technology, equipment which used to be the latest in modern mining have now slipped into obsolence. Mining companies need reliable, productive equipment in order to compete in today's market. In Western coal mining, as coal seams become deeper, older equipment must be replaced with that which can do the job more efficiently.

Jan 1, 1998

By Lizbeth A. Escobar, Phol M. Llanos, Maritza Y. Avila

The present research develops the estimation of critical parameters such as the distances and times between holes to avoid failure due to dynamic pressure in electronic detonators based on the near-field ground vibration model of Holmberg & Persson and the hydrodynamic model of Neyman.

Feb 1, 2020

By Tyler Rockley, Cara Rosen

Blasting at a granite quarry in eastern Maryland produces elevated air blast readings that can fall into the cautionary zone for the state of Maryland environmental regulations on a semi-regular basis. When designing blast patterns in this quarry, challenging geology creates rough and uneven blast faces that can be difficult to capture with 2D laser profiling fully. Utilizing several methods known to manage high air blast results like pattern adjustments, decking, and timing changes have not achieved consistent outcomes.

Feb 1, 2020

By Tyler Rockley, Cara Rosen

Blasting at a granite quarry in eastern Maryland produces elevated air blast readings that can fall into the cautionary zone for the state of Maryland environmental regulations on a semi-regular basis. When designing blast patterns in this quarry, challenging geology creates rough and uneven blast faces that can be difficult to capture with 2D laser profiling fully. Utilizing several methods known to manage high air blast results like pattern adjustments, decking, and timing changes have not achieved consistent outcomes. Accurately capturing and modeling this geology is the key to controlling high air blast. 3D modeling and profiling by drone is the solution to understanding accurate face profiles and real minimum burdens. Using 18 months of blasting data and air blast results to establish a baseline, the comparisons between blasts designed with 2D profiling and blasts designed with drone 3D profiling show improvement in air blast levels. Additionally, shots with completed drilling were drone profiled to understand precise amounts of burden for each borehole. This 'audit' of a blast allows for custom loading of explosives, accommodating the amount of burden present on the blast face. 3Dprofiling is not a new tool in the blasting industry, but a drone alleviates some of the restrictions ground systems face. Controlling and managing air blast, as it pertains to face burdens, requires an understanding of those burdens from all angles. A drone provides that distinct level of insight. The results of this study indicate that drone profiling is managing the customer's air blast readings, allowing the customer to maintain their license to operate within the community.

By Dale Preece, Steven Case, Cassidy McAllister

Simplot Phosphates produces high quality phosphate fertilizer through open pit mining. The operation near Vernal, UT began as a three-pass mining process carried out with drill and blast followed by the combined effort of shovel-truck and dozer material removal. The first two passes removed the overburden and the final pass mined the relatively hard phosphate ore for processing at the mill. Vertical blastholes were employed in all of the mining passes.

Jan 1, 2012

By Frank Hirthammer

Since the introduction of the Explosives Track & Trace in Europe in 2014 for manufacturers and 2015 for end-users, a lot has changed in all areas of the supply chain and the use of explosives. The regional associations, manufacturers' organizations, and trade associations have proven that it is possible to overcome a hurdle, that looks almost impossible in the beginning, through consistent cooperation. The paper gives an insight into the problems involved in introducing such a requirement, identifies ways and solutions, and concludes them. When looking at the current situation, the paper describes the process by which a prescribed change in business processes are transforming into a solution that increases productivity, security, and handling. It shows examples from daily work, in which possibilities for optimization, improved quality assurance, and work facilitation are explained. It presents the resulting potential by comparing process flows, before and after the introduction of Track & Trace solutions. What challenges will we face in the future concerning the use of T&T solutions? Will the tracking of explosives become the norm worldwide? What are future hardware and software developments to be expected? What impact will this have on the global supply chain?

By Jorge Cárdenas, José Luis Hurtado

The critical distance determination test through direct recording for the mine in Phase 03 was carried out in January 2024, and in it the vibration and pressure models were obtained for the Sedimentary breccia unit. The method of obtaining the records is based on the capture of individual pressure waves generated by distant loads, sequenced in periods of 600 ms for easy identification. The test set up corresponds to a variation of that used to obtain the vibration model, and uses 08 wells for loads and 04 for instrumentation. The results apply a safety factor of 1.2 and 1.5, being 16,000 PSI and 13,250 PSI respectively. The values are valid for any distance greater than 5.5 m, this being the minimum established between wells for loads according to the configuration defined in the field, also considering that in 5.0 m of instrumentation the section of the drill hole with the sensor called S1 collapsed. The results of the analysis of the test, generated with Heavy Anfo 82 explosive, with a final density of 1.15 g/cc, are presented. The results of the modeling and generation of the graphs and tables presented show behavior in line with the concept of scaled distance. It is important to consider that in water conditions there is a high impact by the condition, which causes the records to be higher than those expected in dry conditions and present less variability. It is for the above reason that the row corresponding to distance with safety factor 1.5 is declared valid. The results are only valid for the rock analyzed, whose medium is homogeneous and constant in terms of lithological composition and that present similar resistance characteristics, fracture frequency and water table levels. As future steps, the objective is to quantify the increase in pressure generated between wells by analyzing time and sequence factors. This analysis aims to explain the occurrence of dynamic pressure events in areas where critical safety distances are observed.

Jan 21, 2025