Search Documents

By Dale S. Preece, Ruilin Yang

Shock wave physics is an important part of air-deck behavior since the bulk explosives in the column impart a shock into the air-deck where the air shock then passes through the air-deck at a rapidly attenuating velocity. Through both high-fidelity modeling and shock physics theory it is shown that the resulting pressure in the air-deck is two orders of magnitude less than the detonation pressure of the explosive. The induced air blast reflects from the bottom of the borehole and this reflected pressure, even though doubled, is still approximately two orders of magnitude less than the detonation pressure. Air-shocks will ring back and forth in the air-deck for a few tens of milliseconds while the adjacent explosive column(s) are detonating. Transmission of the initial shock through the air along with reflections is an intensive energy consuming process. Energy balance results in shock heating of the air and a temperature increase. However, the increased temperature of the air is also orders of magnitude less than that of the explosive detonation products immediately behind the detonation front. Replacing high energy explosives with zero energy air-decks in a blasthole will always have a negative impact on the adjacent rock fragmentation and movement.

Jan 1, 2016

By W B. Gregg

"A review, update, and expansion of Thiokol’s presentation at BAl’s Fiih High Tech Seminar titled ‘ADetonator - An Era of Precision in All-Electronic Detonators” is provided herein (and should be considered as a supplement to that publication). Thiokol is currently in the development and field evaluation phase of activities for our ACCUBLASTTM all-electronic detonator. The ACCUBLASTTM detonator uses a semiconductor bridge (an electronic match) in place of a conventional hot wire to initiate a safer, less sensitive material, titanium subhydride potassium perchlorate. The device is programmable to provide blast delays in one millisecond increments ranging from 1 to 500 milliseconds. The ACCUBLASTTM detonator combines an all-electronic programmable timer coupled with a semiconductor bridge to ensure detonation timing accuracy with +I00 microsecond precision. Initial development and field testing have been completed. These tests have verified ACCUBLASTTM detonators’ precision."

Jan 1, 1995

By Jhon Silva-Castro, Russell Lamont

Understanding the behavior of materials subjected to high strain rate conditions is of fundamental importance to the mining industry. Several stages of the mining process involve high speed loading rates including blasting, scraping, comminution, etc. Technical comprehension of how rocks deform, fracture, and fail under these loads is a fundamental first step required prior to any serious attempts at optimization of the energy utilized for pertinent activities in the mining process. A Split-Hopkinson Pressure Bar (SHPB) was designed and constructed at the University of Kentucky to study the dynamic properties of various types of rocks.

Jan 1, 2017

By P. Lozada

The objective currently demanded from controlled blasting techniques is to minimize damage to the remaining rock mass while protecting the integrity of mine walls and ensuring the quality of the fragmented material for easier extraction. Finding this balance represents one of the three main challenges faced by large open-pit mines. They must achieve mine stability by complying with slope designs while also maintaining good results in terms of fragmentation and equipment productivity. The main constraints are related to unfavorable geological conditions, water presence, limited drilling diameters and available explosive products, as well as managing drilling times and blast scheduling, among others. For slope control, in addition to presplitting, blasting designs generally include buffered rows, drilled with smaller diameters, and loaded with fewer kilograms of explosives than production holes. The objective is to reduce the powder factor (kg/t) to minimize the energetic influence on the walls and attenuate damage. However, this often requires using very short charge lengths compared to the bench height (one-third or less) and reducing the pattern geometry, which increases the number of holes per ton and drilling costs. This traditional technique of reducing powder factor in the buffered rows has the main limitation of not being able to distribute the explosive energy throughout the entire column, leading to fragmentation issues mainly in the steaming area. Measurements conducted by Orica in their operations indicate at least a 30% increase in P80 particle size in the buffer zone associated with this condition. To improve energy distribution, techniques such as decking, or vertically decoupled charges can be employed. However, these techniques cannot be applied under wet conditions, and strict control over implementation quality is required to avoid deviations, which increases loading operational times and resource required. In this sense, the use of less energetic and lower-density explosives is a better alternative. On one hand, they allow for complete charge columns in the buffered rows, ensuring homogeneous fragmentation, and on the other hand, they reduce the energetic influence on the slopes, significantly decreasing vibration levels. With less energy per kilogram of explosive (MJ/kg) and less charge per linear meter (kg/m), it becomes possible to handle higher specific charges and longer explosive columns, providing flexibility in drilling and loading design options without compromising slope stability.

Jan 1, 2024

By C E. Johnson, S Hosein

Previous researchers have put forward two different theories as to the origin of air overpressure from quarry blasting. In 1980, Siskind et al postulated that the initial face movement gave rise to the displacement of air and that this resulted in the air overpressure pulse. However in 1990 McKenzie et al carried out research that indicated that the air overpressure pulse came into being as a consequence of the shock wave created by the detention of the explosive charge in a blast hole. In an attempt to evaluate these hypotheses, an investigation was undertaken over a 4-year period with the aim of determining the precise origin of air overpressure. The research was carried out at a chalk quarry in the North of England.

Jan 1, 2017

By A. Torrance

A better understanding of the detonation performance of an explosive charge can be gained by directly measuring pressure, temperature and velocity of detonation (VOD). This is particularly important with commercial explosives because their performance is directly influenced by the degree of confinement given by the borehole diameter and the surrounding rock mass. A project funded by the Australian Coal Association Research Program (ACARP) was initiated in early 2009 with the view to design and build cost effective prototype instrumentation to measure the relative differences in detonation pressures and temperatures of commercial mining explosives. The project’s primary focus was on low density explosives. Low density (also referred to as low shock) explosives have been available in various forms for nearly 20 years. Identifying the pressure release patterns of both conventional and low density explosives under different geotechnical conditions should provide the necessary information to both validate detonation codes and better define input parameters for breakage and fragmentation models. This paper gives a general description of the prototype instrumentation developed and reports on the results obtained to date in testing the proposed instrumentation in laboratory scale conditions.

Jan 1, 2011

By Stephen Mansfield, Nathan West, El Khalil Seyed

In October 2017, a multi-bench failure occurred in the east wall of the Guelb Moghrein copper and gold mine in Mauritania. The failure extended 100 m (328 ft) vertically and horizontally and resulted in the sterilisation of ore, but no equipment or personnel were put in danger. The remediation plan successfully removed the failed material and the cutback resumed to a modified pit design, leaving ore reserves behind. In 2021 after completion of mining in another part of the pit, a plan was formulated to develop a narrow cutback behind the failed wall and recover the sterilised ore. Infill drilling defined a resource of approximately 2.9 Mtonne (3.2 Mton) of ore at 0.78% Cu and 0.67 g/t Au at a strip ratio of 5.5:1. The high strip ratio meant that it was necessary to mine thirteen benches of waste, or 156 m (512 ft) vertically, over a two-year period before reaching the first ore, with the cutback only being economically viable if all ore could be depleted at the end of the third year. The high economic risk of the project required a holistic approach to mitigate the risk of another wall failure, by addressing the following areas: 1. Pit Design: with help from an external Geotechnical Consultant, the pit design was optimised to include increased factors of safety, reduced stress points, lower overall slope angles and straight lined walls were replaced with curved walls. 2. Geotechnical Management: the site Geotechnical Superintendent worked closely with an external Geotechnical Consultant to better understand the structural geology. Slope monitoring was improved through an expanded network of prisms, regular in field inspections and the use of a slope monitoring radar. 3. Drill and Blast: new drill and blast designs were developed from first principles, consisting of production, wall control and presplit designs. Blast master polygons and bench development sequences were developed with consideration of the structural geology and the influence of the initiation designs. 4. Mine Operations: improving operational discipline was a critical factor that ensured the accurate execution of drill and blast designs and excavation to bench levels and pit limits. This holistic approach has enabled the safe development of the cutback down to the 936 RL (relative level), two benches below the point at which the previous wall failure occurred. Extraction of ore has occurred from the 960 RL, and due to faster than planned excavation rates, the cutback is expected to be completed ahead of schedule.

Jan 21, 2025

By Tom Watts

The practice of pumping bulk blasting agents is regulated by many agencies around the world. The explosives manufacturers have done an excellent job of hazard and operability studies allowing criteria to be established for the safe pumping of water based blasting agents. The challenge of a Bulk Trucks or Mobile Manufacturing Units (MMUs) manufacturer is to take the objectives of the regulatory agencies and the explosives manufacturers and responsibly design and build MMUs that are safe, compliant, and cost effective without compromising serviceability.

Jan 1, 2011

The following situation was submitted as an ethics case study for inclusion in the Journal. To the best of our knowledge, they are based on actual circumstances encountered in the field. Blowing the Whistle Protecting Confidentiality or Doing the Right Thing? This case centers around a construction job and involves a contractor, subcontractor/blaster, and a farmer/homeowner who lives near the job site. It is essentially a study of professional ethics versus morality, our professional code of conduct versus what is right or wrong.

Jan 1, 2007

By Brad Bockey

Whether you are a driver, blaster, or are in charge of filing, you must recognize the importance associated with DOT-required recordkeeping. As various agencies become intertwined with rules governing the explosives industry, the records we produce must be as accurate as possible. The time is right for reviewing your paperwork process from start to finish.

Jan 1, 2011

By William Reisz

Managing the blast site at almost any operation can be a daunting task. There are so many details that must be observed, understood, and acted upon. It goes without saying that there are no two locations that have the exact same challenges and concerns. The level and the extent of these challenges can vary widely.

Jan 1, 2014

By Jane Wright, Brent Blanchard

Question: When it comes to demolition projects, what could be more demanding than asking a blaster to explosively demolish a stubby, heavily-reinforced concrete structure in the heart of a third-world country? Answer: Asking them to fell only half. Such was the charge recently put forth to Controlled Demolition Group (CDG), Yorkshire, UK when they were called to Casablanca, Morocco to provide a stunning demolition effect for the upcoming Universal Pictures film Spy Game, starring Robert Redford and Brad Pitt. Director Tony Scott (True Romance, Enemy of the State) contacted the renowned demolition firm after seeing their work on television and receiving recommendations from explosives manufacturers. The film’s producers then asked the CDG team if they could bring down half of an apartment block as part of a dramatic suicide bomber sequence.

Jan 1, 2002

By William Reisz

In our line of work,like many other professions, there may be times when circumstances or a series of events may arise, contributing toward unacceptable risk. When multiple parties are involved, there will almost inevitably be differences on how best to deal with these situations. Unless approached in an intelligent and these differences may often have the potential for costly and unexpected results.

Jan 1, 2014

By William Reisz

The explosives and blasting industry has a commendable safety and security record, especially over the last several decades. This is due in large part to our newer technologies, better training and education, engineering practices, corporate initiatives, our professional organizations, and whether we like to admit it or not - our regulatory agencies.

Jan 1, 2012

By Steve Dillingham

A blast site incident has just occurred. Tensions are high, and, as the blaster, you’re in charge of the crisis at hand. Your mind is reeling, your thoughts frantic. The main areas of concern for you at the scene are to deal with immediate problems...aid the injured, take a head count, assess the damage, call emergency response, contact company headquarters, calm the neighbors, update your customer, and respond to the press on site. You feel as if all the bases have been covered...but, then again, have they? One of the biggest mistakes blasters and their companies can make is not including their Insurance carrier in the critical on-site accident procedures and emergency call list. Unfortunately, many companies believe that they are immune to the perils that can often, within a matter of minutes, create chaos that only happens to someone else.

Jan 1, 2002

By Robert Hopler

Torpedoing Wells. – On the completion of the drilling, or when the production is found to decrease, it is usual to “torpedo” the well to increase the flow. This process was patented in 1862 by Colonel Roberts, who believed, with many others, that the oil was contained in crevices in the rock, which might not have been tapped by the bore-hole. He therefore proposed the use of nitroglycerine, gunpowder, or other explosive, to break up the rock at the bottom of the well, so that these rich “pockets” might be brought into communication with the well.

Jan 1, 2007

By Ricardo Dr. Chavez, Mathieu Lachamp, Rob Dr. Farnfield

Pueblo Viejo is an open pit gold mine in the Dominican Republic which is always looking forward to implement the newest technology in the industry to improve all processes. Focusing on one of the pillars of the department and our company, digitalization, we’ve been looking for the technologies that allow us the automation of data generation, supervision and process innovation. That’s where a new Drill and Blast software takes place, helping to integrate the process from the beginning to end, right after the pattern is designed until it’s blasted, allowing us to track results like vibration, fragmentation, performance, cost and inventory of each blast in a single platform. The software helps engineers to generate back analysis by blast, bench, pit, month and many other ways, in a timely friendly manner. Therefore, we can catch business opportunities and improvement for the drilling and blasting process.

Jan 1, 2019

By Edward P. O'Hern

The importance of the so-called explosives and the increasing extent of their use are evident from the fact that the production in the United States for the year 1910, as shown by the United States Census reports, amounted to the enormous total of approximately 480,000,000 pounds, this being more than double the production of 1905 and more than three and one-half times that of 1900

Jan 1, 2015

By James Stuart

A man died when the primed charge he was holding against his chest exploded. He was doing legitimate explosive work, and he was following all the safety procedures he had been taught. He and his colleagues had done this, thousands of times previously, with no ill effects.

Jan 1, 2007

By Ashley Haslett

A European Directive on Identification & Traceability of explosives came into effect on the 4th of April 2008. This directive is intended to establish a harmonised system for the unique identification and traceability of all packaged explosives, detonators, reels of detonating cord and primers used in civil applications across the European Union. The directive must be adopted into the national legislation of each European Union member state by the 5th of April 2009 with compliance achieved throughout Europe by the 5th of April 2012. The requirements of the Directive apply to all explosives manufactured, used and imported into the European Union from 5th April 2012.

Jan 1, 2010