Search Documents

By J. L. Holman

The Bureau of Mines has extended its previous development of cast Mn-Cu damping alloys to powder metallurgy (P/M) consolidation of alloys containing 55 to 75 wt-pct Mn. Blends of minus 200-mesh elemental powders were compacted cold in directional and isostatic presses. With 1 pct binder, typical green densities ranged between 76 and 80 pct of theoretical when pressing at 30 or 48 tsi. Green strength increased with compacting pressure and copper content. As-sintered tensile strengths ranged to 60,000 psi fox a hydrogen, sintered 60Mn-40Cu alloy, along with 5-pct elongation. Sintered densities ranged between 90 and 96 pct of theoretical. Sintering (a as effective when holding for 1 hr at maximum temperatures of 900° to 1,040` C, dependent on composition. Strength and ductility were considerably lower than for equiva¬lent cast alloys. When aged to the damping condition, alloys containing 60 to 70 pct Mn exhibited >40 pct specific damping capacity (SDC) at 5,000-psi stress, considerably higher than values reported for equivalent cast material. Effects of 1 or 3 pct Sn or Zn additions on SDC and other properties were assessed. Trials were conducted on consolidating rings and gears of the 65Mn-35Cu alloy on industrial-type P/M equipment.

Jan 1, 1979

By L. W. Higley

It is estimated that well over 20 million lb of chromium and 8 million lb of nickel, plus other metal values, are diverted annually to furnace dusts, mill scale, and contaminated swarfs in the domestic stainless and other specialty steelmaking industry. Little inroad has been made toward the in-plant recycling of these wastes to reclaim the metal values. The Bureau of Mines has devised a process for recovering about 90 pct of the chromium and molybdenum and well over 90 pct of the nickel and iron from stainless steelmaking furnace dusts, swarf, and mill scale. Other metals such as manganese are also recovered. Initial laboratory results were confirmed and expanded to include a wide variation of stainless steelmaking waste mixtures. Later experiments have included specialty steelmaking wastes other than from stainless steelmaking. Significantly, the ease of technology transfer has been demonstrated by a number of industrial-sized (19-ton) commercial electric furnace heats, in which the pelletized wastes represented some 10 to 20 pct of the furnace charge, replacing part of the normal scrap charge. Results of these successful large-scale trials are presented. Some information is also presented on incorporation into the pellets of chromium-bearing particulate wastes originating from other than steelmaking production. Cost evaluation indicates the process is economically attractive.

Jan 1, 1982

By E. P. Ferrero

Crude oils from fields throughout the world are analyzed by the Bureau of Mines to determine the characteristics of the oils and their contribution to the petroleum resources of the world. Analyses are reported for 169 foreign crude oil samples from 122 oilfields in Africa, Asia, Australia, the Caribbean, Europe, North America, and South America. Tables show the geographic and geo- logic origin of the samples, names of companies that supplied the samples, annual production for the fields, general characteristics and analytical and computed data, hydrocarbon-type data, cumulative production of the larger fields, and references to sources of geological and field development information. The analyses were made by the Bureau of Mines routine method and comparisons may be made with more than 8,000 other such analyses.

Jan 1, 1972

By Kenneth H. Johnston

This report describes an in situ combustion project and three waterflood projects in Allen, Anderson, and Wilson Counties, Kansas, that will be visited during the 1964 annual tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the movement of heavy crude oil through the reservoir and into the wellbore with energy furnished by burning s portion of the crude oil therein. Another feature is the simultaneous injection of C02 and water, through separate tubing into input wells during early development, to increase injectivity at moderate pressures, Discussion of individual projects includes information on their early history, source and treatment of injection fluids, oil production-decline curves, and the results of water injection on oil production.

Jan 1, 1964

By Gary Friedline

As a consequence of the Coal Mine Health and Safety Act of 1969(PL91-173), the Bureau of Mines (BOM) entered into a contract with Ocean Energy Inc. (OEI) to develop, fabricate, install, and evaluate a permissible lighting system for use on a longwall coal mining operation. The program schedule is shown in Figure 1.1. The proposed regulations are contained in Appendix A. The initial part of the program involved a survey of existing longwall lighting practices in Germany and England and an evaluation of a variety of lighting components on a mockup of a longwall mining operation that was fabricated under this program. Visits made to German and British mines uncovered major differences in lighting level requirements, permissibility aspects, size, and operating constraints which identified wide disparities and essentially eliminated from further consideration any known imported lighting devices for meeting the higher lighting levels and standards proposed for US coal mines by the Mining Enforcement and Safety Administration (MESA). The longwall mockup provided use¬ful information regarding the amount of illumination required, physical size and shape of lamps, light distribution problems, cable routing, use of connectors, signaling, glare, and other important factors unique to the lighting of low coal longwalls.

Jan 1, 1975

By Wilbert J. Huff

This is the sixth of a series of annual reports describing the work of the Explosives Division, Bureau of Mines, United States Department of the Interior.3/ It deals particularly with the activities of the division from July 1, 1940 to June 30, 1941. The studies outlined in this and preceding reports of the series have been conducted under the direction of the author and the respective unit leaders, to whom specific credit is given.

Jan 1, 1942

By Wilbert J. Huff

This is the sixth of a series of annual reports describing the work of the? Explosives Division, Bureau of Mines, United States Department of the Interior.3/ It deals particularly with the activities of the division from July 1, 1940, to June 30, 1941. The studies outlined in this and preceding reports of the series have been conducted under the direction of the author and the respective unit leaders, to whom specific credit is given.

Jan 1, 1942

By Robert C. Steckley

A study of joints in Marathon County, Wis., was made to determine the orientation of regional paleotectonic stresses and to develop a method of using optical diffraction analysis (ODA) in studying joint orientations and spacings. Standard geologic and petrofabric techniques employing the use of a geologic compass and a Schmidt net were used in gathering, describing, and reducing joint orientation data. Analysis of selected outcrops with ODA indicates that ODA can be applied to study both joint orientations and spacings. ODA is shown to be a rapid method that can be used to complement standard petrofabric techniques, especially in the study of joint spacings.

Jan 1, 1972

By Joan Weinberg

Seasonally adjusted new factory orders for primary metals declined in January, February, and March, especially in the steel industry. The decline was part of an apparent slowdown for the entire manufacturing sector. Orders for all durable goods, including not only primary metals, but also clay, glass, and stone products, fabricated metal products, machinery, and transportation equipment, fell in January and February. In March, orders rose a slight 0.8%. According to the U.S. Department of Commerce, the downturns in durable goods orders in January and February were the first back-to-back declines in 3 years. They were largely attributed to a drop in orders for transportation equipment, mainly auto-mobiles and aircraft, while the small gain in March was due to a surge in aircraft orders. Higher interest rates may be partly responsible for the slowdown in durable goods orders over the past 3 months. The higher rates have also hit the construction industry--another major end-user of minerals. Construction of new homes and apartments fell by a seasonally adjusted annual rate of 5.4% in March, following a 12% decline in February.

Jan 1, 1989

By Alfred Wild

The Kraftile Co. plant, Fremont, Alameda County, Calif.--the largest producer of glazed, structural wall units west of the Rocky Mountains-- maintains modern processing facilities to evaluate and blend a wide variety of clays from several sources to produce quality products. The report desribes the prospecting, exploration, and test methods used to locate raw material sources and covers processing methods, cost factors, and trends. Also, the geologic and ceramic factors are considered in a general discussion of the economics, potentials, and requirements of clays as raw materials for ceramic tile manufacturing.

Jan 1, 1963

By Laird Crocker

A goal of the Federal Bureau of Mines is to minimize the undersirable environmental conflicts and impacts associated with mineral processing operations. To help reach this goal the Bureau operated a citrate-process pilot plant for the removal of sulfur dioxide from lead smelter sintering machine waste gases to test the process. The process uses a carboxylate solution such as citric acid to absorb sulfur dioxide from waste gases. The absorbed sulfur dioxide is subsequently reacted with hydrogen sulfide to precipitate sulfur and regenerate the solution for recycle. Nominal capacity of the pilot plant was 1,000 scfm of 0.5 vol-pct sulfur dioxide gas. The pilot plant was operated for over 5,400 hr and produced about 55 net tons of sulfur. The operation demonstrated that (1) 99 pct of the sulfur dioxide could be removed from lead smelter sintering machining waste gases containing from 0.1 to 0.6 vol-pct sulfur dioxide, (2) sulfur precipitation and solution regeneration with hydrogen sulfide in conventional stirred vessels was readily controlled, (3) precipitated sulfur could be continuously recovered as a 99.S-pct-pure product by flotation and melting, and (4) 78 dry-vol-pct hydrogen sulfide gas could be produced from pilot-plant product sulfur, natural gas, and steam.

Jan 1, 1979

By H. L. Anthony, A. C. Richardson, G. D. Coe

"INTRODUCTION The Warrior View mine of the Seaboard Coal Corporation is located in Tuscaloosa County on the Warrior River about 14 miles northeast of Tuscaloosa, Ala. The Brookwood bed at this point yields a coal with fair coking qualities, and the product from neighboring mines on this bed has been used for the manufacture of blast furnace coke. The output of the Warrior View mine, however, is used exclusively for domestic and steam-raising purposes.This paper continues the series° of reports on the washability of Alabama coals which are based upon the study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal mining companies. This paper contains screen-sizing and float-and-sink tests of a representative sample of run-of-mine coal, and flakiness and crushing tests on certain sizes.Published information on the Brookwood bed is very meager. Fieldner6 gives the proximate and ultimate analyses for a number of seam samples taken from representative mines working this bed. Gandrud and Britton7 show sections of this bed taken at Searles, Ala. They also give the specific gravities of the coal, the bone, and the shale partings.Table 1 give the proximate and ultimate analyses for the 3/4 to 3/16 inch size of raw coal. Table 2 gives the sulphur content and the ash fusibility temperatures of the float-and-sink fractions for this same size. The character of the coal is very uniform throughout the range of sizes produced and, as it was not convenient to have these analyses on all sizes, this size was chosen as being representative of the coal. From the information available it is evident that the coal preparation problem is restricted to one of ash reduction.SAMPLING AT THE MINEAt the Warrior View mine the run-of-mine coal is dumped from the mine cars upon a 3-inch grizzly. The oversize is crushed in rolls set at 24 inches and joins the undersize before being elevated to the raw-coal bin ahead of the jig. The sample was caught at the point where elevates discharges into the raw-coal bin, by taking a proportional amount of the coal at 10-minute intervals over the period of a day's run, The total sample amounting to 2.7 tons was shipped to the laboratory at Tuscaloosa for the washability studies."

May 1, 1932

By Kenneth H. Johnston

This publication describes a thermal-recovery project and two waterflood projects in Carter, Garvin, and Stephens Counties, Okla., that will be visited during the 1966 annual tour by the Bureau of Mines in cooperation with the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects arc (1) the movement of heavy (15° to 28° API gravity) crude oil through the reservoir and into the well bore with energy furnished by burning a portion of the crude oil therein; (2) the use of an inverted nine-spot pattern with dually completed injection wells, to produce oil from deep (8,200 to 10,200 feet) reservoirs; and (3) the flooding of five sand lenses separately by using controlled water injections through multizone completed injection wells. Discussion of the individual projects includes information on their early history, method of completing and operating wells, source and treatment of injection fluids, oil production decline curves, and the results obtained from the development.

Jan 1, 1966

By Kenneth H. Johnston

This publication describes a thermal-recovery project and two waterflood projects in Carter, Garvin, and Stephens Counties, Okla., that will be visited during the 1966 annual tour by the Bureau of Mines in cooperation with the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects arc (1) the movement of heavy (15° to 28° API gravity) crude oil through the reservoir and into the well bore with energy furnished by burning a portion of the crude oil therein; (2) the use of an inverted nine-spot pattern with dually completed injection wells, to produce oil from deep (8,200 to 10,200 feet) reservoirs; and (3) the flooding of five sand lenses separately by using controlled water injections through multizone completed injection wells. Discussion of the individual projects includes information on their early history, method of completing and operating wells, source and treatment of injection fluids, oil production decline curves, and the results obtained from the development.

Jan 1, 1966

By W. W. Adams

"The seventh National Safety Competition, that for 1931, conducted by the United States Bureau of Mines, was participated in by 350 mines and quarries operating in 34 States. Tables 1 to 5 show the relative standing of the various plants, Bronze trophies, known as the ""Sentinels of Safety,"" which were provided by The Explosives Engineer magazine to be awarded annually by the Bureau of Mines were awarded to five companies, each company having established the best accident—prevention record within one of the five classes into which all companies were divided — namely, anthracite mining companies, bituminous—coal mining companies, metal—mining companies, operators of nonmetallic mineral mines other than coal mines, and quarries or open—cut mines. The trophies are awarded for one year and are then transferred to the winners of the succeeding year's contest.The outstanding feature of the contest of 1931 was the operation of a bituminous coal mine without a lost—time injury to any employee. While accident—tree records had previously been made by certain quarries, metal mines, and nonmetallic mineral mines, never before has such a feat been accomplished by a bituminous coal mine in the National Safety Competition. Whether or not such a record has been made by a bituminous—coal mining company not enrolled is the competition the writer does not know, but it is believed that the case referred to is unique among large coal—mining companies. The mine to which reference is made is No. 1 mine of the Phelps Dodge Corporation, at Dawson, N. Mex. To that company belongs the distinction not only of being the first coal—mining company among those enrolled in these yearly safety contents to operate its mine without an accident but also of occasioning the 'Sentinels of Safety' trophy for a bituminous mine to take its first journey west of the Mississippi River. For the past six years the trophy has been in West Virginia, Alabama, or Pennsylvania."

Jun 1, 1932

By H. P. Greenwald

Cooperation between the Bureau of Mines of the United States Department of the Interior and the Safety in Mines Research Board of Great Britain dates from 1924. It has been intimate and has involved exchange of personnel and. equipment as well as information. Correlation of divergent results obtained in large-scale tests of the explosibility3/ of coal dusts made in the respective countries was one of the first problems to be studied. The purpose of this paper is to show to what extent such correlation has been achieved. COMPARISON OF TEST METHODS The first research accomplished Jointly by the two organizations was a comparison of large-scale methods of determining the explosibility of coal dust. Large samples of coal were exchanged and subjected to test in the Bureau's Experimental coal mine and in the Board's steel gallery, 38 inches

Jan 1, 1939

By H. P. Greenwald

Cooperation between the Bureau of Mines of the United States Department of the Interior and the Safety in Mines Research Board of Great Britain dates from 1924. It has been intimate and has involved exchange of personnel and. equipment as well as information. Correlation of divergent results obtained in large-scale tests of the explosibility3/ of coal dusts made in the respective countries was one of the first problems to be studied. The purpose of this paper is to show to what extent such correlation has been achieved. COMPARISON OF TEST METHODS The first research accomplished Jointly by the two organizations was a comparison of large-scale methods of determining the explosibility of coal dust. Large samples of coal were exchanged and subjected to test in the Bureau's Experimental coal mine and in the Board's steel gallery, 38 inches

Jan 1, 1939

By Philip K. Hopke

A systematic study of the mechanism of interaction of 218Po(RaA) armed by the decay of 222Rn with airborne particulate matter has been made. The rate of attachment of RaA to particles in the diameter range of 0.1 µm to 10.0 µm has been measured as a function of particle size, concentration, and composition, radon concentration, time of interaction, relative humidity and temperature. It was found that under the conditions in these experiments the attachment rate was proportional to the square of the particle diameter and varied with temperature and relative humidity. The composition of the particles apparently has no effect on the attachment. The variation in attachment rate was related to a sticking probability coefficient of approximately 0.02 that varies systematically with temperature and humidity. In addition, the rate of deposition of RaA on the wall of the attachment kinetics system was measured and also found to change with temperature and relative humidity.

Jan 1, 1980

By Chas. F. Jackson

The work of the Mining Division is divided among seven sections, each in charge of a supervising engineer, as follows: 1. Metal-mining methods section, the supervising engineer of which is also supervising engineer of the Southwest Experiment Station at Tucson, Ariz. 2. Metal-mining research section. 3. Nonmetal-mining section. 4. Coal-mining section. 5. Mine-ventilation section. 6. Mineral-industries survey section. 7. Electrical section. The names of the sections indicate broadly the fields covered by each, and in the following, pages the objectives and type of work of each section will be summarized briefly and their active problems listed. The work clone during the fiscal year 1937 will also be summarized.

Jan 1, 1937

By William C. Cooley

This study Identifies and evaluates deposits of noncoal minerals in the U.S. which are most amenable to be mined underground hydraulically and transported hydraulically. A method was developed to screen and compare mineral deposits including economic comparisons. The most applicable minerals for hydraulic mining by borehole monitor jets from underground entries are soft uranium sandstones In Wyoming in locations where water is available. This method with hydrotransport could improve the safety, health and economy of underground uranium mining. Soft oil-bearing sandstones in California and Texas could be mined and transported by this method more safely than by other underground mining methods. Other weak sandstones may be hydraulically mined economically. Man, minerals are too hard to be mined by monitor jet but are amenable to hydraulic transport and hoisting. Uranium sandstone in New Mexico is of interest because of potentially improved health and safety in transport and lower transport cost, Increases in mine output for potash, in New Mexico and trona in Wyoming can be achieved most economically by adding hydraulic hoisting when existing skip capacity is at its limit. Research is recommended to obtain site-specific data on the feasibility of mining uranium ores by monitor jets.

Jan 1, 1981