Search Documents

Illumination hardware developed in conjunction with previous Contracts H024202l, H0242049, and H0242023 had not been adequately tested in actual underground work situations. The purpose of this contract was to install and monitor this equipment on mining machines and in actual working places of coal mines to gain experience with the use of the lamps and support equipment in the abusive and critical environments for which they were intended. The equipment that was to be tested consisted of the following: a. Lamps -A variety of sizes of permissible fluorescent lamps which operate from 12 volts DC power. These include the following sizes: Model 8, (9 watts) 2" diameter; Model 15/2 (14 watts) 2" diameter; Model 15/3 (21 watts) 3" diameter; Model 20 (25 watts) 3" diameter; Model 30, (28 watts) 3" diameter; and Model 40, (39 watts) 311 diameter. Representative photographs of these lamps are shown in Figure 1-1 and 1-2.

Jan 1, 1976

The works recorded in this Test Report have been performed by Rade Roncar - Electrotechnical Institute of Zagreb, SFR Yugoslavia in collaboration with Bureau of Mines. The main objective of these investigations was to investigate the possibility of fabrication of thin-walled square enclosures of satisfactory safety factor in accordance with requirements of effective technical regulations. The results and the investigations can be divided in three main fields: - investigations of thin-walled enclosures with the view of determination of pressures causing technological deformations before performing tests in accordance with effective applicable regulations, - finding the safety factor by means of tests of metal-foam pressure vents, - comparison of enclosures with and without pretreatment by technological deformation.

Jan 1, 1987

Mining men and State officials in their efforts to make mining safer are confronted from time to time with various complicated questions. In recent gears these questions have tended to increase with the use of mechanical appliances. Twenty-five years ago electricity had been used but little in mires; today there is practically no other means of transmitting power employed in American mines, except that in metal mines compressed air is used, chiefly for drilling and for operating small portable hoists. In coal mines there has been a great increase in mechanization, which tends to concentrate the work of production in small areas and to increase the local difficulties of ventilation; also, it has intensified locally the hazard from coal dust as well as firedamp in bituminous and subbituminous mines. The answers to the questions that arise are not always obvious, as is shown by the fact that even able, experienced men differ in their opinions of the best, way to overcome a particular mining hazard. The difficulty of .solving the problems is also demonstrated by the varying provisions in mine-safety rules, both in official regulations and in the rules of those mining companies that are endeavoring to do more than follow the letter of the law. Such differences of opinion as to the best way of meeting a difficult situation are often found within the same mining organization, and, similarly, varying opinions are held by different members of the Bureau of Mines staff.

Jan 1, 1937

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1988

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By R. H. Lien

The Bureau of Mines has conducted research on a flue gas desulfurization (FGD) process as part of its goal of minimizing the undesirable environmental impacts associated with sulfur dioxide (S02)-bearing waste gases. This FGD process, referred to as the modified citrate process, involves absorption of S02 in a buffered citric acid solution. The absorbed S02 is subsequently stripped from the solution using steam, which regenerates the solution and produces a wet S02 product. This product can be further processed to make sulfuric acid or liquid S02. Economic evaluations showed the process to be expensive when the stripper was operated at or near ambient pressures because of the large amounts of steam required for solution regeneration. Research was directed at reducing steam consumption in the stripper. The effect of stripper pressure on steam consumption was investigated. A process research unit (PRU) was operated with the stripper pressurized in the range of 5 to 150 psig. Test results showed that steam consumption decreased with increased stripper pressure. For example, when operating the PRU stripper at 150 psig, 4.1 grams of steam per gram of S02 was required to remove 90 pct of the S02 from a 1.0-vol-pct-S02 gas. This compares to 7.1 grams of steam per gram of S02 required for 90-pct S02 recovery at 5 psig.

Jan 1, 1982

By J. Roth

The purpose of the present study is to increase the safety of explosive storage. This was accomplished by: a) review of the histories of recent and past magazine explosions to define causes and trends; b) observation of present-day explosive storage conditions and practices at active mines; c) examination of existing Federal regulations on explosive storage to determine whether they address all conceivable safety problems, whether they contain redundant or obsolete standards, and whether their intent is clearly stated; d) recommendation, for safety improvements and for revision and clarification (if necessity) of governmental regulations. Magazine explosions are rare. A recent increase in magazine explosion frequency must be attributed to a large increase in deliberate (criminal or malicious mischief) explosions. Fires of various origins account for the remaining explosions of the past decade. During 1884-1926 several lightning-generated explosions occurred in non-metal magazines, but none recently. It appears that the contents of a well-constructed, metal magazine are immune to direct lightning strikes, regardless of whether the magazine is grounded or not grounded. Grounding a metal magazine cannot be harmful, but it may well be superfluous. Magazines were observed at 34 widely separated mines and storage problems were discussed with personnel at these mines. In general, storage conditions and practices were found to be satisfactory. Usually, only small quantities of explosives are stored on mine property since most explosives are brought in by suppliers when needed. MSHA and BATF standards on explosive storage appear to cover safety aspects adequately. However, certain revisions are recommended to clarify some of these standards and to reduce inconsistencies in their enforcement.

Jan 1, 1983

By Ferdinand Roehlich

An evaluation of the use of manually activated, installed,. dry chemical fire protection systems on underground metal and nonmetal mine vehicles is described. In addition, an assessment of the possible health risks posed by the dry chemical extinguishing agents used in such systems is provided. Work involved installation of fire protection hardware on an operating piece of underground metal/nonmetal mine equipment and, via actual fire tests, a determination of the effectiveness of the hardware in extinguishing on-vehicle fires. Two fire protection systems were installed on a Caterpillar 988 front-end loader in St. Joe Mineral's Fletcher mine, near Viburnum, Mo. Both a fully pressurized Safety First CM-20 and a nonpressurized cartridge actuated Ansul A-101 were installed for comparative purposes. Both systems operated satisfactorily during an 8-month endurance trial period which preceded the actual fire tests. Each system was able to extinguish an 18" x 4" class B test fire placed in the engine area of the machine. The health hazards analysis of dry chemical powder consisted of a detailed search of published literature relating to these multipurpose agents. This data was verified via a controlled laboratory analysis of two monoammonium phosphate based powders (Safety First Unikem and Ansul Forey) and an analysis of air samples collected at various locations on the test vehicle during the fire tests. Although the powder was found to be nontoxic, two potentially dangerous thermal decomposition products were identified--ammonia and phosphoric acid. However, later analysis indicated that an operator would not be exposed to dangerous concentrations of either compound if he were to remain outside of the powder cloud. A "Selection and Use Manual for Manually Activated, Fixed Fire Suppression Systems on Underground Metal and Nonmetal Mining Equipment" was prepared both as an, appendix to the report and for distribution under separate cover.

Jan 1, 1977

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and maintenance costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per elm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured underground. The computer outputs for each simulation run are presented in Volume II of this report.

Jan 1, 1983

By W. E. Schroeder

Two underground installations of the sprayfan system are described and evaluated. The spray fan proves capable of reducing by 1300 percent downtime due to high methane. Spray fan face ventilation at 20 ft brattice setback is shown to give improved methane control over conventional sprays at 10 ft setback. In addition, this report describes: ? A simple method for determining the most economical application of ventilation for face methane control ? The effect of place variables (primary ventilation, auxiliary ventilation, seam height, etc.) on methane concentrations ? The correlation of methane concentrations with brattice setback. These results are utilized to suggest a safer and more economical approach to face methane control.

Jan 1, 1981

By Richard L. Fowler

An automatic steering control system was designed, installed and tested on a coal mine shuttle car. The system utilizes sensors and associated signal processing electronics developed under a previous phase of this contract. The automatic steering system performs the routine guidance functions of turning corners and straight-through tramming. The shuttle car driver retains full authority of speed, braking, load and unload functions and at any time may exercise his option with manual override or steering. Steering information is generated from signals derived from the existing Lateral Guidance sensor subsystem, and all operational features of the previously developed open-loop system are retained. Above ground system tests were conducted in a simulated mine constructed of wood panel ribs. Results were in good agreement with prior hybrid computer simulations undertaken to validate the basic control system over a broad range of conditions and to select system parameter values. The automatic steering system was successfully demonstrated in the above ground simulated mine to USBM technical representatives. Designed to meet USBM permissibility requirements, the system is ready for a Phase II underground testing program. Testing in actual underground mine environment is expected to provide additional data regarding recommended performance improvements and implementation techniques.

Jan 1, 1975

By J. Vance Batty

The Permian Red Bed copper deposits of the South Central States are a potentially important resource. Only the higher grade, near-surface ores are now exploited because conventional froth flotation does not recover oxidized copper minerals which comprise 10 to 15 percent or more of the copper content of typical ore. Laboratory-scale beneficiation studies were initiated to devise a method capable of recovering both sulfide and oxidized copper mineral. Testing established that the high clay and gypsum content of typical ore prevented effective flotation of the oxide mineral using sulfidizing, fatty-acid, or oil emulsion techniques. A modified leach-precipitation-flotation (L-P-F) procedure recovered over 90 percent of the copper, compared to a recovery of 77 percent obtained by conventional sulfide flotation. The higher costs of the L-P-F method would reduce the increased revenue from higher copper recovery. An increase in copper price and/or an increase in oxide copper content of the ore would make the L-P-F process comparatively more attractive.

Jan 1, 1970

By C. E. Wood

A special appropriation made by Congress in July 1940 provided funds for the investigation of methods for recovering manganese from low-grade [ ] domestic deposits. These funds were assigned to the United States Department of the Interior, Bureau of Mines. A committee, identified as the Technologic Committee on manganese of the National Research Council, National Academy of Sciences, was appointed to recommend the allocation of the funds for investigation of the more promising projects.

Jan 1, 1942

By C. E. Wood

A special appropriation made by Congress in July 1940 provided funds for the investigation of methods for recovering manganese from low-grade [ ] domestic deposits. These funds were assigned to the United States Department of the Interior, Bureau of Mines. A committee, identified as the Technologic Committee on Manganese of the National Research Council, National Academy of Sciences, was appointed to recommend the allocation of the funds for investigation of the more promising projects.

Jan 1, 1942

By J. J. Wallace

This report describes the initial phase of Bureau of Mines research in the hydraulic mining of bituminous coal. The mining site and equipment are described, and the test procedures and results obtained with a bar-mounted monitor are given. Tests showed that hard Pittsburgh-bed coal can be mined hydraulically from a solid face at water pressures of 4,000 pounds per square inch.4 Coal was penetrated to a depth of 4 feet in 20 seconds with 225 gallons of water per minute coming from a 3/8-inch nozzle at 4,000 pounds per square inch pressure. Some difficulty was encountered in cutting the binders occurring in the coal; it was not possible Lu penetrate directly the overlying draw slate.

Jan 1, 1961

By William N. Patterson

Drive systems for mining machines are usually sized to accommodate anticipated peak loads. Usually, the average power requirements are considerably less. Energy storage and power averaging are attractive concepts for mining machinery and could have far-reaching implications. The purpose of this program was to: ? Identify truly feasible concepts, ? Identify advantages/disadvantages, limitations, and constraints, ? Evaluate feasibility based on today?s technology, ? Identify anticipated safety problems, and ? Provide the designer with a comprehensive literature base. Concepts evaluated include flywheels, high energy batteries, gas charged accumulators, inductive storage, capacitive storage, springs and counterweights, thermal, closed cycles, internal combustion engines, trolley systems, and hybrid systems. A comprehensive reference index is provided. Included is an appendix containing abstracts of the pertinent literature.

Jan 1, 1980

By E. P. Youngman

In the absence of any subsequent enactment of mining legislation, the Turkish mining law in effect in 1914, when Iraq became a British mandate, is still operative. The Constitution, or Organic Law, of Iraq, adopted by the Constituent Assembly on July 10, 1924, in articles 113 and 114, provides that:3 Ottoman en laws date and thao remained and lave pub- lished on or after that date and which have remained in force in Iraq u to the time of the publication of this law shall remain in force in Iraq' so far as circumstances permit, subject to any modi- fication or repeal in conformity with the proclamations, regula- tions, and laws referred to in the following article, and until they are altered or repealed by the legislative power or the High Court issues a decision rendering them null and void in accordance with the provisions of article 86. (Art. 113.) All proclamations, regulations, and laws by the Commander-in- Chief of His Britannic Majesty's Forces in Iraq, the Civil Commis- sioner, and the High Commissioner, and those issued by the Govern- ment of His Majesty King. Faisal, during the period between Novem- ber 5, 1914, and the date of the coming into force of this Consti- tution, shall be considered to be valid as from the date on which they came into force... (Art. 114.) 4 According to a German authority, it is the Turkish law of March 26, 1906, that, with a few modifications, is still in force. This law (similar to the French law of 1810) is discussed in a separate section of this paper.

Jan 1, 1933

By Henry C. Meeves

The Bureau of Mines, between 1956 and 1963, examined 18 major pegmatite districts in Arizona, Colorado, New Mexico, South Dakota, Utah, and Wyoming to evaluate their content of beryllium, a material in short domestic supply that has become increasingly important to modern industry. This examination report includes the salient statistics on the production of pegmatite minerals other than quartz and feldspar; and brief descriptions of 170 specific pegmatite deposits.

Jan 1, 1966

By James H. Rowland

The Mine Improvement and New Emergency Response Act of 2006 (MINER ACT) established a Technical Study Panel (The Panel) to provide recommendations on the utilization of belt air and new technology that may be available for increasing the fire resistance properties of conveyor belt used in underground coal mines. The Panel Report recommended use of the Belt Evaluation Laboratory Test (BELT) as the method for testing and approval of flame resistant conveyor belts used in underground coal mines. The research conducted to establish the correlation of the BELT with large-scale belt fire flammability tests was done using 36- to 42-in wide conveyor belt. Due to today?s coal haulage capacity, the mining industry is using 72-in and wider conveyor belts. The National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine if the BELT will also qualify wider belts as fire resistant for use in underground coal mines. This paper describes the results of recent experiments comparing results from using the BELT and the large-scale tests for six different belts.

Jan 1, 2010

By Lisa A. McDonald

The environmental compliance process affects all aspects of hardrock-mining operations, from exploration through post-closure. The primary components of the environmental compliance process are requirements under the National Environmental Protection Act of 1969 (NEPA) and the permitting requirements associated with various other federal, state and local laws. This study considers the Greens Creek Mine and the development of two other projects (Alaska-Juneau & Kensington). These mines were used as the foundation for a case study of the impacts of the environmental compliance process on hardrock-mining activity in Southeast Alaska. The case study presents the institutional and legal requirements, followed by a discussion of the impact of this process on the production and timing of the three mines. The results of this preliminary study reveal some interesting findings, some expected and others unexpected, regarding the impact of the permitting process on the exploration, development and (proposed) operation of the three mining projects in the Juneau area. Determining the cost of compliance with these requirements is an important step in evaluating the appropriate course of action to protecting the environment while providing the necessary raw materials needed for society. This preliminary study highlights the initial starting point for such an analysis.

Jan 1, 1992