Search Documents

By Fred N. Kissell

In This Chapter [The explosibility of methane gas mixtures Effect of pressure and temperature on explosibility Less common sources of methane ignitions The amount of methane stored in coal Forecasting the methane emission rate Layering of methane at the mine roof When the recirculation of mine air is hazardous The importance of higher air velocity in preventing methane explosions and Mine explosions, barometric pressure, and the seasonal trend in explosions] Dealing with methane in mines and tunnels requires knowledge of the circumstances under which dangerous accumulations of methane are likely to occur. This knowledge involves the properties of the gas itself, an awareness of where these accumulations are likely to occur, and facts on how methane mixes safely into the mine air. The other chapters in this handbook address the handling of methane under a variety of specific circumstances, such as at continuous miner faces or coal storage silos. This chapter addresses some broad concepts that serve as a foundation for the suggestions provided in other chapters. THE EXPLOSIBILITY OF METHANE GAS MIXTURES Methane entering a mine or tunnel often enters as a localized source at high concentration. Figure 1–1 depicts a cloud of methane being diluted into a moving air stream. In this illustration, methane enters the mine from a crack in the roof. As the methane emerges from the crack, it progressively mixes with the ventilation air and is diluted. In the event that this progressive dilution reduces the concentration from 100% to 1%,2 as shown in Figure 1–1, the methane passes through a concentration range of 15% to 5%, known as the explosive range. In the explosive range, the mixture may be ignited. Above 15%, called the upper explosive limit (UEL), methane-air mixtures are not explosive, but will become explosive when mixed with more air.

Jan 6, 2006

By William H. Lewis

Energy Research Corp., under contract to the Bureau of Mines, has developed a new miners' caplamp battery. The new battery is based on nickel-cadmium technology and offers significant improvements in performance with reduced size and weight when compared to the conventional lead-acid battery presently in use. This report describes the design and fabrication of the nickel-cadmium battery, which utilizes a roll-bonded electrode structure. The final battery design has a 15-A-h capacity in a 2-112-lb package, which is over 2 lb lighter than the present lead-acid caplamp battery.

Jan 1, 1983

This report presents the results of studies of Kennecott Copper Corporation's tailings embankment at Magna, Utah. The stability studies described were performed on only one cross section of the embankment, utilizing; data obtained from drilling, sampling, and testing, which was limited in nature. The main objective of the data collection was to provide background information to support the overall research effort. Because of this limited scope, it is not possible to evaluate the degree of safety or adequacy of the embankment or disposal system, and the information and data contained in the body of this report must be judged in that light. The first part of this report contains discussion of site geology and seismicity, pertinent information on the refuge disposal system, a discussion of the tailings materials characteristics, a summary of the engineering analyses, and A bibliography. The second tart (appendices) contains basic geologic and engineering data supporting the discussions in the first part of the report.

Jan 1, 1974

By Dennis E. Jensen

Field studies were performed during blasting operations for strip coal mining above the room and pillar workings at Jenny mine in eastern Kentucky. The study is part of the Bureau of Mines program to develop criteria for the proximity of surface blasting to underground mines. Measurements and observations were made to identify physical changes in the mine. No change in the frequency of roof falls or any other indication of apparent damage was noted. Recordings of blast induced vibrations were made using sensors on the roof and floor of the underground mine and at the ground surface. A maximum particle velocity of 17.5 in/sec was recorded on the mine roof. The vibration data were analyzed and comparisons were made between roof vibration levels and those recorded on the mine floor and at the ground surface. Results are compared with previous blast vibration studies. Recommendations are made for further study toward developing criteria.

Jan 1, 1979

By Robert L. Lagace

A whole-mine experiment to assess the practical feasibility and utility of the dedicated-wire technique for overcoming poor trolley carrier phone system performance at a large underground coal mine was designed, performed, and evaluated. The technique involves the use of a single, low-loss, properly terminated and branched auxiliary wire placed in the rail haulageway. This auxiliary dedicated wire allows signals to electromagnetically couple to the trolley wire/rail transmission line, and thereby significantly decrease the overall signal attenuation rate on the trolley wire/rail line. The in-mine dedicated-wire demonstration program and its results, conclusions, and recommendations are described. The dedicated-wire technique is shown to be a valid and practical one for significantly improving carrier phone system performance in coal mines.

Jan 1, 1981

By J. M. Mutmansky, C. Lee

"IntroductionRecognition of Coal Workers' Pneumoconiosis (CWP) as a major occupational disease has affected various aspects of the coal mining industry in the United States as well as in almost all major coal producing countries, Regulations related to the control of coal mine dust forced mine operators to modify their mining and ventilation practices. As the coal production record of the last 15 years shows, this had both direct and indirect impacts on the productivity and production costs.To identify the causes of CWP, many research efforts have been made throughout the world. Most of these studies were epidemiological in nature, attempting to pinpoint exposure and seam variables that affected the incidence of the disease. Other studies have been oriented toward the elemental and mineralogical composition of the coal dust in the mine atmosphere and in the miners' lungs. These studies indicate that there may exist some relationships between the characteristics of the coal mine dust and the prevalence of the disease. Some of the variables that are thought to affect the occurrence of CWP are the mass of the dust in the working place, the rank of the coal, the existence of certain trace elements, the free silica content of the coal, and the existence of other minerals in the respirable dust. A more complete description of these previous research studies has appeared elsewhere (Mutmansky and Lee, 1984).The behavior of particles in the human lung is known to be governed by their aerodynamic diameter, which is defined as the diameter of a hypothetical spherical particle with unit density that exhibits the same settling velocity as the given particle. Because of this fact, the aerodynamic size distribution of coal mine dust is one of the parameters to be determined along with the other physical, elemental, and mineralogical characteristics. The objective of this paper is to establish a strategy for providing coal mine respirable dust samples for characterization purposes using instruments that classify according to the aerodynamic diameter. In addition, several findings concerning characterization methods will be presented"

Mar 1, 1989

By W. R. Hardwick

This paper describes block -caving methods and practices of the Bagdad Copper Corp. in Yavapai County , Ariz . It is one of a series being prepared by the Federal Bureau of Mines on mining methods , practices , and costs in various mining districts of the United States . The story of the Bagdad caving operation is of particular interest because the ore body was not as thick as at other mines where the method had been successful . At Bagdad the caving method worked very well as a smallscale operation of 300 tons per day but was abandoned when production was increased to 2,000 tons per day . The Bagdad mine is in western Yavapai County , Ariz . , about 22 miles northwest of Hillside , a station on the Phoenix -Ash Fork branch of the Atchison , Topeka & Santa Fe Railway system ( fig . 1 ) . Copper ore now is mined by open -pit methods . The ore is concentrated , and the concentrates are trucked to Hillside and shipped by rail to a custom smelter . Some molybdenum sulfide is produced as a byproduct . This report gives a brief history of the district , describes the ore de- posit , and outlines the methods of prospecting , exploration , and estimation of ore . Development and former underground mining , including stope preparation , stoping , and transportation , are described . Extraction of ore , production rates , miscellaneous operations related to mining , wage and contract systems , and method of concentration are described . The final section discusses mining costs . The underground mine was visited by the author several times between 1937 and 1942 , and some information has been drawn from personal notes . The property again was visited in June 1957 , and maps and plans for this paper were furnished by the company at that time ; they have been edited to conform with Bureau of Mines format . The underground mine could not be visited then because it had been closed in 1948 when open -pit mining was begun .

Jan 1, 1959

By A. U. Miller

Definite progress has been made in accident prevention in Illinois during the past few years; the State Department of Mines and Minerals is receiving excellent cooperation from coal companies and employees, the companies are making greater effort to maintain their mines in good condi- tion, and the employees are eliminating more unsafe practices. As a result, some coal companies have made commendable safety records that prove that coal can be mined with a comparatively low accident rate. However, there is need for further improvement, as the accident rate of the State as a whole is much higher than it should be. During the 55-year period 1882-1936, in- clusive, reports of the State Department of Mines and Minerals show a total of 7,005 (an average of 127.36 per year) men killed in and around the coal mines. Of this number, 6,425 (91.7 percent) were killed underground, 346 (4.9 percent) in the shaft, and 234 (3.3 percent) on the surface. Of the fatalities underground, 3,300 (51.3 percent) were killed by falls of roof, sides, or face coal, 1,167 (18.1 percent) by haulage, 639 (9.9 percent) by handling explosives, 579 (9 percent) by explosions, 151 (2.3 percent) by electricity, and 589 (9.1 percent) by other means. Of the fatalities in the shaft, 171 men (46.5 percent) were killed by falling down the shaft, 14 (41.6 percent) by the cage, and 31 (8.9 percent) otherwise. On the surface, 113 (48.2 percent) of the fatalities were due to railroad cars, 51 (21.7 percent) to machinery, and 70 (29.9 percent) to other causes. The fact that 7,005 lives (an average of 127.36 per year) were lost during 1882-1936 is sufficient evidence that in the past too little interest has been taken in safety by either the management or workers. A realization of this deplorable loss of life should act as an incentive to the industry to make greater effort to prevent accidents in the future. After an accident occurs, the facts pertaining to it become history, and anything that may be done afterward cannot change in any way the damage that has already been done, such as loss of life, personal injury, and destruction of property. The main benefit that can be derived from an acci- dent is that suitable procedure may be adopted and some lesson may be learned to aid in preventing a similar accident in the future. All accidents, par- ticularly serious ones, therefore should be investigated and an effort made

Apr 1, 1938

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Robena No.4, located near Waynesburg, Pennsylvania. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. With present instrumentation, the spectrum can be covered from 40 Hz to 400 kHz. It is recorded using broad-band analog magnetic tape, and the noise data are later transformed to give spectral plots. The other technique records noise envelopes at several discrete frequencies for a sufficient amount of tine to provide amplitude probability distributions. The specific measured results are given in a number of spectral plots and amplitude probability distribution plots. The general results are that at frequencies below 10 kHz, power line noise within the mine is severe. Impulsive noise is severe near arcing trolleys, and at lower frequencies near any transmission line. Carrier trolley phone signals and harmonics are strong throughout the mine whenever the trolley phone is in operation. Additional information beyond that included in this report may be obtained from the authors, who are with the Electromagnetics Division of the National Bureau of Standards.

Jan 1, 1974

By Roy E. Peterson

The Bureau of Mines conducted bench-scale research to evaluate materials which showed potential as low-cost reductants for use in the ironmaking industry. These materials were lignite, subbituminous coal, coal char, tree trimmings, refuse--derived paperboard, used crankcase oil, and peat. To compare their effectiveness, the materials were tested in the reduction roasting of nonmagnetic taconite and, except for oil and peat, in the reduction of iron oxide pellets to metallized pellets. Reduction was conducted in a 18-cm-diameter, rotary drum, which was externally heated in an electric furnace. Over 92 pct of the iron was magnetically recovered from a nonmagnetic taconite after roasting with any of the reductants, but greater quantities of reductant were required to achieve this when the waste materials were used. The fossil fuels were also more effective for metallizing pellets, although metallizations above 90 pct were also obtained with tree trimmings and refuse paperboard. However, refuse paperboard had to be frequently recharged to the furnace because it depleted rapidly.

Jan 1, 1983

By G. R. Peterson

To determine the availability of aluminum from world bauxite resources, the Bureau of Mines investigated 139 bauxite deposits worldwide and evaluated the potential production of aluminum based on the demonstrated resources of bauxite ore from 91 mines and deposits in 22 market economy countries. The demonstrated resources of the bauxite mines and deposits included in this study represent an in situ resource of 20.2 billion metric tons of bauxite. Total identified bauxite resources in market economy countries amount to roughly 31.9 billion tons. Of the demonstrated resource, some 18.8 billion tons of bauxite considered minable provide a production potential of 3.6 billion tons of primary aluminum. Given the wide geographic distribution of bauxite deposits, stable supplies of bauxite for aluminum production seem assured well into the next century. However, a tight market situation could develop during the 1990's unless the real price of aluminum increases enough to stimulate massive new investments in production capacity, particularly in refining and smelting. This study indicates that a real price of at least $0.85 per pound (in January 1980 dollars) would be necessary to stimulate the required investments and provide a sufficient rate of return on invested capital.

Jan 1, 1983

By D. D. Southworth

In 1981, 1982, and 1983, the Bureau of Mines examined the potential for lode deposits of platinum-group metals (PGM) in the Goodnews Bay ultramafic complex, Alaska. The complex consists of the Red Mountain, Suzie Mountain, and Smalls River ultramafic bodies and displays concentric zoning of rock types similar to complexes in southeast Alaska, British Columbia, and the Ural Mountains in the U.S.S.R. Results of the study indicate that platinum is preferentially associated with chromite and magnetite in the dunite core of the complex, and palladium is preferentidlly associated with sulfide minerals in the outer clinopyroxene-rich zones. the most promising targets for PGM lode deposits are the chromite-rich dunite at the heads of Fox Gulch and Squirrel Creek and iron-nickel and iron copper sulfide-bearing magnetite clinopyroxenite and hornblende-rich rocks outward of the dunite core, also in the Fox Gulch-Squirrel Creek area. Significant placer reserves are present in the unmined, deeply buried placer ground in the lower Salmon River Valley, and also in tailings from previous dredging.

Jan 1, 2011

By B. W. Gandrud

[This report presents the data of one of a series of investigations of the washability of Alabama coals as indicated by float-and-sink tests mode by the Bureau of Fines at the Southern Experiment Station in cooperation with the University of Alabama and Alabama coal producers. The Klandyke mine, operated by the Blocton Mining Co., is about 1 mile eat of Vest Blocton, Bibb County, Ala., floor the southwestern, extremity of the Cahaba coal field. The Bureau of Mines already has published three reports that deal with the, washability of Cahaba coals - one a washability study of the Clark bed at Marvel4/ one on the tabling of fine coal from the Thompson and Woodstock beds5/, and the third a washability study of the Henry Ellen bed at Acmar6/.]

Jan 1, 1939

By W. A. Calhoun

The purpose of this investigation was to develop economical mineral dressing processes for removing objectionable quantities of impurities, such as quartz and pyrite, from refractory clay deposits in east central Missouri. The presence of excessive quartz in these clays causes crazing. Pyrite causes bloating and unsightly dark blobs on the surface of fired refractory brick. The iron concentration in the proper state of oxidation may also act as nucleation centers for carbon crystal growth which can result in bursting of the refractory. Numerous deposits, representing a very large tonnage, have been examined and prospected by various refractories companies and found to contain impurities in objectionable quantities. Upgrading these clays would greatly extend our reserves of high-quality refractory clays. Wet-tabling and wet-cyclone concentration were found to be effective for removal of impurities from clays. Of the two methods, wet-cyclone concentra¬tion would be cheaper and more effective. Although wet-tabling improved the refractory properties of each clay, beneficiation by wet-cyclone produced clays of superior quality. Clay recoveries by wet-cycloning ranged from 56.1 to 81.8 percent of the weight of the crude samples, and the beneficiated clays contained from 71.9 to 94.4 percent of the total alumina. The pyrometric cone equivalent (PCE) was increased from 1 to 3 cones by wet-cycloning. The beneficiated clays also met the reheat shrinkage requirements on refiring to 1,400° C. Missouri is one of the major domestic sources of fare clay. In addition to deposits of high-grade refractory clays, there arc many deposits that contain small percentages of impurities, which render the clays unfit for the production of high-heat-duty firebrick. Development of methods to beneficiate these submarginal clays to usable materials would greatly increase commercial fire clay resources.

Jan 1, 1961

By R. S. Dean

In general, the Division conducts investigations relating to the treatment of ores and metallurgical products from the condition to which they are mined to the refined metal. At the object of conserving natural resources and eliminating waste by furnishing information on current methods of metallurgical practice making fig fundamental studies of metallurgical processes and developing new processes and alloys to the point of demonstrating their or value. Office of the Chief Engineer The functions of the technical units of the Office of the Chief Engineer are indicates

Jan 1, 1941

By Terry McMahon

This Bureau of Mines report describes the rock burst problem and measures being taken for its alleviation in the deep underground mines of the Coeur d?Alene Mining District in northern Idaho. The geologic features that contribute to rock bursting in that area are discussed and briefly compared with similar features in other burst-prone mining districts throughout the world. Early investigations to understand and control rock bursting are reviewed, and the mechanics of bursting are discussed in terms of the seismic events that produce them. Sources of strain energy, rock failure mechanisms, and the conditions necessary for the release of seismic energy are covered in detail. Rock burst research in the Coeur d'Alene District is described. Included are discussions of the microseismic method as both a research tool and as a rock burst monitoring system, rock destress blasting and preconditioning methods for rock burst control, and stoping methods currently being developed to reduce rock burst hazards.

Jan 1, 1988

The Minerals Data Source Directory is a compilation of descriptive information on the availability, content, and location of minerals data in the Federal Government. It is intended to assist Government personnel and the general public in locating and acquiring minerals information. Included in the Directory are descriptions of data bases, publications, information systems, and information offices containing data pertaining to all aspects of mineral production, consumption, trade, and related information. These mineral data sources include the Federal agencies such as the Department of the Interior's Bureau of Mines and Geological Survey whose major mission is the collection and dissemination of mineral information. Also included are agencies such as the Departments of Agriculture, Commerce, Labor, State, and Treasury, and the Central Intelligence Agency, whose primary mission is the collection of data in non mineral subject areas, but in which the mineral industry is a component.

Jan 1, 1982

By Terry S. Cory

This report covers magnetic field strength measurements vs range and frequency In low-medium coal mines. Both quasi-conductor-free and conductor-proximity areas were Investigated. The program covered 5 mines, 4 seams, 6 measurement sets, and 3 geographic areas, The results have been summarized In terms of maximum communication range expected per seam and noise condition. Scatter gain Is further explored as a simple measure of energy coupled to conductors.

Jan 1, 1978

By John A. Organiscak

Enclosed cabs are a primary means of reducing equipment operators? silica dust exposure at surface mines. The National Institute for Occupational Safety and Health experimentally investigated various factor effects on cab air filtration system performance. The factors investi­gated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind effects on cab particulate penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that intake filter efficiency and recirculation filter use were the two most influential factors on cab penetration performance. Use of the recirculation filter reduced cab penetration by usually an order of magnitude over the intake air filter alone because of the multi­plicative filtration of the cab interior air. Intake air leakage and filter loading affected the cab penetration to a lesser extent, while wind had the least impact on cab penetration between the calm and 10-mph wind velocities tested. Adding an intake pressurizer fan notably increased intake airflow and cab pressure with only minor changes to cab penetration. A mathematical model was developed that describes cab penetration in terms of intake filter efficiency, intake air quantity, intake air leakage, recirculation filter efficiency, recirculation filter quantity, and wind penetration.

Jan 1, 2008

By John A. Organiscak

Enclosed cabs are a primary means of reducing equipment operators? silica dust exposure at surface mines. The National Institute for Occupational Safety and Health experimentally investigated various factor effects on cab air filtration system performance. The factors investi­gated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind effects on cab particulate penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that intake filter efficiency and recirculation filter use were the two most influential factors on cab penetration performance. Use of the recirculation filter reduced cab penetration by usually an order of magnitude over the intake air filter alone because of the multi­plicative filtration of the cab interior air. Intake air leakage and filter loading affected the cab penetration to a lesser extent, while wind had the least impact on cab penetration between the calm and 10-mph wind velocities tested. Adding an intake pressurizer fan notably increased intake airflow and cab pressure with only minor changes to cab penetration. A mathematical model was developed that describes cab penetration in terms of intake filter efficiency, intake air quantity, intake air leakage, recirculation filter efficiency, recirculation filter quantity, and wind penetration.

Nov 1, 2008