Search Documents

By D. B. Taliaferro

[Recovery of core specimens from subsurface formations and their subsequent analysis are important aids in efficient development and operation of oil and gas fields. Core specimen first were obtained mainly for the geologic information they revealed; now they are on analyzed to determine many of the physical characteristics and conditions of the subsurface formations as well. Cores recovered from the producing formations may be analyzed for porosity, permeability, oil content, "connate" water content, and other physical and chemical properties of the formation, all to the end of furnishing enough data for making reliable estimates of the quantity and availability of oil and gas within reservoir and in devising efficient means for their withdrawal.]

Jan 1, 1939

By J. W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and, from the data developed, to determine: (a) Which coals, either as mined or after beneficiation by conventional preparation, are suitable chemically under present standards for producing metallurgical coke. (b) Which coals require special and more intensive treatment in preparation than is now practiced. (c) Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation. This report is one in a county series and describes the preparation characteristics of the coals of Logan County, W. Va. According to present-day standards for metallurgical coal, many believe that the sulfur content of the coal should not exceed 1.25 percent? Coal with more than this amount has been used for making metallurgical coke, especially when blended with coal containing less sulfur. In this series of reports 1.25 percent sulfur is used as a gage to determine whether or not a coal will be suited for metallurgical coke.

Jan 1, 1957

By D. D. Walker

Scheelite, the most abundant tungsten mineral in the Philipsburg region of Montana, is found in replacement deposits and along fissures and cracks in limestone at various distances from contacts with acidic igneous rocks. It also occurs at the limestone-igneous contacts, but typical garnet tactites are developed in only a few places in the region. The most favorable host rocks for scheelite mineralization are the Jefferson, Hasmark, and Madison limestones. Scheelite is exposed in float, outcrops, and surface and mine workings along a 2-mile-wide belt extending southwest from Lost Creek beyond Silver Lake, a distance of 15 miles or more. (See fig. 1.) Some scheelite is found in veins formerly mined for silver. Powellite and molybdenite occasionally are present with the scheelite. Hubnerite occurs in quartz veins in the Black Pine area 10 miles northwest of Philipsburg. These quartz veins occur in the quartzites of the Precambrian Spokane formation. Tungsten production in the region has come almost exclusively from scheelite deposits, both lode and placer. During a 6-year period beginning in 1943 a total of 142.0 tons of 63-percent W03 concentrate was produced by H & H Mines Co. In the early 1950's, the Trigger mine produced 4,000 tons of 1-percent W03 ore and the Tip Top 650 tons of 2.0-percent W03 ore and 2,906 tons of 2.2-percent ore. There has been sporadic production from some of the smaller properties in the area.

Jan 1, 1960

By William F. Jahn

Because of the' situation in Europe during the summer of 1939, with the possibility of war and consequent curtailment or loss of supplies of tin to the United States, the Bureau of Mines undertook an investigation of domestic tin resources. This was permitted by the Strategic Minerals Act of 1939, which authorized investigation of possible domestic resources of strategic minerals necessary in a national emergency. The minerals selected were in short supply, and the United States depended almost entirely on imports to meet normal requirements. The Black Hills of South Dakota were selected for investigation as one possible source of tin because of the occurrence of the mineral there has been known since 1876, although production had never been important. The Tinton area, in the northern part of the Hills, had received the most attention and contained some minor indicated and inferred tin deposits.

Jan 1, 1949

By John Paul Gries

During World. War II, when the curtailment of imports led to an unprecedented demand for domestic mica, beryl, spodumene, and other pegmatite minerals, the Bureau of Mines and the Geological Survey entered upon a program designed to expedite mining of these minerals from the Black Hills area of South Dakota. The program involved napping, sampling, and drilling of many pegmatite dikes in the southern portion of the Black Hills and beneficiation conducted in the field and in the Bureau of Mines laboratories at Rapid City, S. Dak., Rolla, Mo., Salt Lake City, Utah, and College Park, Md. This report describes the occurrence and sampling of the Beecher No. 2 pegmatite, which was investigated as part of the general pegmatite study in South Dakota. Investigation of the Beecher No. 2 pegmatite was started on November 20, 1943, and terminated in the spring of 1944. During this period, the Bureau of Mines took a series of trench samples across the pegmatite at the surface for grain-count studies and chemical analyses. The Geological Survey mapped the geology of the deposit after it was exposed by trenching and stripping.

Jan 1, 1950

By Krishna P. Sinha

An investigation was made to determine the creep behavior of oil shale at elevated temperatures. During the first phase of the investigation, work done on creep behavior of geologic materials was reviewed and triaxial creep tests on oil shale were planned. Tests at temperatures up to 250°C and axial stress up to 3000 psi were conducted at no confinement and at confining pressures equal to 1/3 and 2/3 of axial stress. Wide variations in the elastic properties as well as creep characteristics are exhibited. Creep deformation is more pronounced at elevated temperature but no definite quantitative remarks can be made regarding effect of grade of oil shale due to wide scatter and limited number of data paints. Primary creep can be described by a power law. Secondary creep seems to be an experimental function of deviatoric stress. Teritary creep was not observed within the test duration (24 hours in most tests).

Jan 1, 1983

By Linneas Laage, Thomas Weber, William Pomroy

"Underground mine fires can significantly influence mine ventilation airstreams, in some cases throttling or even reversing airflows. As a result, the performance of a metal and nonmetal mine stench fire warning system, which depends on the ventilation to carry the vital warning signal, under fire conditions is different from performance under nonfire conditions. The safety of underground miners can be jeopardized if the warning signal is delayed. This Bureau of Mines report describes research to investigate fire and stench warning system interactions. A computer model is presented that permits quantitative analysis of stench warning signal delays as a function of fire location and intensity. The results of a case study involving computer simulations of stench distribution in a hypothetical mine network subject to various fire exposures are also discussed. This case study illustrates a technique for identifying the areas within a mine that are subject to unacceptable warning signal delays, thereby enabling preemptive action by mine personnel, such as redeployment of stench injectors. INTRODUCTIONFires are an ever-present threat to the safety of underground miners. Since the smoke and toxic gas produced by a mine fire can be spread rapidly by the mine's ventilation system, mine evacuation must be accomplished as quickly as possible in the event of fire. In metal and nonmetal mines, the most common means of passing the fire warning signal to each miner is the stench system. The typical stench system utilizes ethyl mercaptan, a highly odoriferous organic compound, injected on the surface into the compressed and/or ventilation airstreams. Upon smelling the stench, workers evacuate the mine according to an emergency preplan.Although the stench system has been used successfully for over 60 yr, it has several serious shortcomings, owing to certain chemical properties of ethyl mercaptan and to certain performance characteristics and limitations of present injection systems.Recent Bureau research succeeded in upgrading the overall safety and effectiveness of the stench system through the use of a superior stench odorant and the development of improved stench injection equipment (1).4 This research has also investigated a specialized computer simulation model capable of calculating the precise concentration of stench in any mine ventilation network branch at any time after stench release (2). An adaptation of the computer model now enables the analysis of stench system and ventilation system interactions under the influence of a mine fire."

Jan 1, 1987

By Michael E. Henderson

Presented in this report are the experimental results of coarse coal slurry degradation data obtained from the Hydraulic Transport Research Facility (HTRF) at the Pittsburgh Research Center (PRC), Bruceton, PA. The facility is operated by Boeing Services International, under Bureau of Mines Contract No. J0333956. Presented in this report are the experimental results of coarse coal slurry degradation data obtained from the Hydraulic Transport Research Facility (HTRF) at the Pittsburgh Research Center (PRC), Bruceton, PA. The facility is operated by Boeing Services International, under Bureau of Mines Contract No. J0333956. This particle degradation report is a summary of the particle distribution data obtained at the HTRF for the period 26 November 1982 to 1 October 1983. The testing covered herein is for coarse Pittsburgh Seam coal in the 6-in (150 mm) and 12-in (300 mm) pipelines, at velocities ranging from 5 to 18 ft/s (1.5 to 5.5 m/s), and at concentrations by weight ranging from 15 to 55 pet. Particle size distribution samples were taken systematically throughout the testing.

Jan 1, 1985

By R. R. Sayers

Mine operators and managers for a number of years have known that the maintenance of health among the workers has an appreciable financial value, In order to maintain the health, it has been found ne cessery to imow; 1. The health hazards existing in the industry as a whole and the specific hazard in the individual mine. 2. The physical condition of applicants for employment as well as that of the old employees. This can be determined only by systematic physical examination of all applicants and of regular employees at intervals of at least once a year thereafter. 3. All cases of sickness that occur among the workers. No operator or manager, or personnel, medical, or safety organization can control or prevent sickness without knowing where, when, and under what conditions the sickness actually occurs. In order to obtain information as to the hazards of industry, investigations have been and are being made of the effects of the condi- tions both in the field under usual working practices and in the laboratory. In the field several factors are generally present which affect the health. The effect of these factors may be determined by studying each of them separately in the laboratory. However, both the field and the laboratory studies are limited in value in that such studies usually have been made over a comparatively short period. While we have some information as to their immediate effect, we do not know to what extent extreme heat, humidity, the presence of dust or other health hazards are the cause of disability. Mortality statistics are probably the most easily available indices as to the hazards of industry. As an example, a study of such statistics among coal miners of Indiana shows a marked increase in the death rate in 1918.

Mar 1, 1923

The Bureau of Mines has reviewed those portions of the "Tariff Schedules of the United States Annotated 1963" that are of interest to the minerals industry. This study shows to what extent rates of duty were altered (increased of decreased), and provides a bridge where possible from the old Schedule A classification system to the new TSUS system of statistical reporting of import data. In general the new tariff has corrected previous classification defects and inconsistencies, but the rates of duties have not been materially changed.

Jan 1, 1965

By K. E. Soroka

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,0000 C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first held field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the 1900's and was surface mined in the 1940's. In the winter of 1961-62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report is the fifth in a five-part series that describes the Calamity Hollow Mine Fire Project. The first report, part 1, describes the design and construction of the field installation. Part 2 will present the results of a continuous 4-month burnout operation. (Because part 2 involves the analysis of a substantial body of data, it will not be published until after publication of parts 1, 3, 4, and 5.) Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and this part (part 5) describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is sufficient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water-injection-fume exhaustion quenching procedure are planned.

Jan 1, 1986

By Charles Will Wright

This paper has been written to aid the owner of a small gold mine or prospect in preparing a report on his property for the purpose of interesting capital. If an owner can afford to do so, he should employ a mining engineer of recognized standing and experience to examine and report on his property, but many owners of small -mines and particularly of prospects cannot make the expenditure required for this. Further, many of them do not know how to prepare a description which will cover those features of a deposit on which a potential investor promises his opinion as to its worth. If such an owner is convinced that he possesses an orebody of sufficient grade and size to warrant the required expenditure for a thorough investigation and wishes to present his property to prospective investors, then the following suggestions concerning the proper way to sample his deposit, estimate the tonnage of developed and probable ore, and prepare a report may be of assistance.

Jan 1, 1933

By Hillary W. St. Clair

Mining activity began in colonial times with ironmaking operations scattered along the eastern seaboard. Iron furnaces and forges manufactured iron implements from bog iron ores using charcoal from the extensive forests as a fuel. Lead ores were mined in the Mississippi Valley and copper ores in the Lake Superior region. However, the real beginning of the American mining industry did not occur until the 19th century. The history of American mining is organized around three epochal events. The first was the discovery of gold in California in 1848, which marked the beginning of a period of apprenticeship in mining and metallurgical techniques. The second was the discovery of the fabulous Comstock Lode in western Nevada in 1859, which expanded mining throughout the Far West and led to large-scale underground mining and the development of smelting techniques for lead, silver, and copper ores. The third event was the building of a transcontinental rail-road system after the Civil War, which brought about the consolidation of the industry from a large number of independent mines, mills, and smelters into integrated operations run by large corporations. Thus developed the mining industry that today supplies the energy and critical materials for the great-est industrial complex the world has known.

Jan 1, 1977

By G. G. Huggins

A demonstration project has been completed to reduce the operator sound level of an underground service vehicle, a personnel dispatch wagon, to go dB(A) or less. The program objective was to implement quieting recommendations made on an earlier study for the USBM n diesel-powered mine equipment. The manufacturer and mine to which the vehicle was going actively participated in the program to ensure a product that was not only quiet, but useful. The key element of the quieting package is an engine part a1 enclosure, which, with several complementary noise control components, reduced the operator sound level 14 dB, from 101 dB(A) to 87 dB(A). The vehicle underwent a 4-month trial period, with no degradation in the quieting package. Mine personnel reported no maintenance difficulties, and were enthusiastic about the dispatch.

Jan 1, 1975

By P. L. Michael

Several evaluations were made by Modified Rhyme Test (MRT) word lists transmitted through various simulations of the Trapped-Miner Communication System being developed by the U.S. Bureau of Mines. The tests were performed in a "single blind? situation so that the evaluators would not be biased by knowing the characteristics of the system being simulated. A computer program was developed to provide a simulation of the electrical aspects of the communication system and to provide an evaluation by calculation of the articulation index (AI). The study indicates that communication through the presently proposed system will be somewhat unreliable at depths as great as 300 metre even with the system operating at maximum effeciency.

Jan 1, 1977

By G. L. Bartlett

"INTRODUCTION The major objective of our research is to help reduce the incidence and severity of coal worker's pneumoconiosis (CWP). To that end, this project is designed to improve our understanding of the processes that lead to pulmonary dysfunction following mine dust exposure, and how those processes might be interrupted or attenuated. The response of the lung ' to inhaled particles is complex, and the course of development of disabling CWP is slow and unpredictable. From among the numerous cellular and molecular interactions involved in the pulmonary response to inhaled particles, this project is focussed on the role that the pulmonary alveolar macrophage (PAM) may play in regulating the activity of fibroblasts.The PAM is the lung cell that has the most immediate and the most obvious interaction with inhaled particles. Within a short period after particles are arrested in the alveolus of the lung, they are phagocytized (engulfed) by these specialized cells. The PAM then has a diverse potential repertoire of subsequent activities. Which reaction actually ensues is determined, in large part, by the nature of the phagocytized _particles. Activated PAMs produce a variety of products that may affect adjacent lung tissue, including superoxide free radical, elastase, collagenase, prostaglandins, platelet activating factor, etc. Those may well be important in the pathogenesis of CWP, but they are beyond the scope of this project. Background information that is cogent to this project has come primarily from investigations using animal models of silicosis and asbestosis. PAMs that have ingested silica particles synthesize and release molecules that control the behavior of surrounding cells. One such mediator is interleukin-1 (IL-1), a molecule that plays a central role in many aspects of the response to injury. It can stimulate fibroblasts (the cells that help to hold tissues together) to release the enzyme collagenase, resulting in breakdown of the structural collagen fibers that support the lung tissue. IL-1 also stimulates fibroblasts to undergo mitosis and to proliferate, which is an initial stage of fibrosis. Certain stimulants cause PAMs to release fibroblast growth factors (FGFs) that are distinct- from IL-1. Under other circumstances activated PAMs synthesize and release molecules that stimulate fibroblasts to accelerate synthesis of collagen fibers, thus contributing to fibrosis. Although these observations provide a valuable precedent for analysis of the mechanisms involved in CWP, their relevance to CWP cannot be assumed since most of those studies involved macrophages or fibroblasts obtained from tissues other than the lung, and because almost none of them have used CMD as the stimulating particles. Therefore, the goal of this project is to learn how exposure to CMD affects the behavior of PAMs, and in turn how products of dust-exposed PAMs affect fibroblasts and the process of fibrosis in the lung."

Jan 1, 1988

These inspection standards have been prepared for use in the Federal inspection of bituminous and lignite mines. They are a revision of "Tentative Coal-Mine Inspection Standards," published as Bureau of Mines Information Circular 7204 in February 1942 and employed a guide for Federal inspections. Numerous changes have been made in the original standards owing in part to recognition of shortages of some types of safety equipment due to the war, in part because of need of additional standards to cover certain mine conditions' arid' practices, and in part to conditions not foreseen when the original standards were prepared. About one-fourth of these standards are marked with an asterisk (*) as being of particular importance in preventing accidents in many coal mines; however; failure to carry out the suggestions made in such of the other standards as are applicable may also' lead' to the loss of lives.

Jan 1, 1943

By John W. Nebgen

This report contains findings from a U.S. Bureau of Mines study concerning the inhibition of acid mine drainage formation from underground coal mines. A series of experiments was performed in which three different pyritic materials (wastes from coal production plants) were evaluated using several candidate inhibiting agents. Data obtained from the inhibitor-treated pyrites were compared with data from control experiments in which untreated pyritic wastes were used. The experiments were conducted by placing treated and untreated pyrite in columns, passing moist air through the columns to promote oxidation of pyrite, and washing the columns weekly to collect oxidation products for analysis. Experimental results indicate that quantities of acid mine drainage can be substantially reduced if soluble iron III (ferric) ion is controlled. The best inhibitors are neutral or alkaline siliceous materials such as fly ash, blast furnace slag, portland cement, and cement kiln dust. These materials appear to insolubilize iron III species to make them unavailable for reaction with pyrite. The data strongly suggest that the soluble ferric ion aqueous is a key oxidant for pyrite to produce acid mine drainage. The role of aqueous ferric ion as an oxidizing agent is substantiated further by data obtained using metallic iron (nails) as an inhibitor. The iron nails tended to keep the soluble iron in the iron 11 (ferrous) state. Experimental results indicate that sulfate and acidity levels are reduced when pyrite is in contact with the metallic iron.

Jan 1, 1979

By C. W. Davis, M. W. Von Bernewitz, S. C. Lind

During the past few years our possible domestic resources of platinum have attracted much attention . On account of the extensive use of platinum during the World War , and the practical elimination of the Russian supply , the price of this metal rose to new high levels , as shown in Table 1 ; and though it since receded to some extent , the price is now nearly six times that of gold .

Jun 1, 1923

By A. B. Needham

In November 1940, the Bureau of Mines started exploration of the Three Blacks manganese properties - Black Diablo. in Pershing County and Black Eagle and Black .Rook in Lander County. The purpose was to determine possible reserves of manganese in the deposits. It is reported that a small amount of manganese was mined from the Black Diablo during World. War 1. No mining except that necessary for assessment work had been done on the Black Eagle. Shipments were being made from the Black Rock deposit to a concentrator at Vain, Nev., while the Bureau's development work was progressing. The Black Diablo deposit consists of one patented claim owned by the Charleston. Hill National Manes Co. Mary L. Clough of Winnemicca, Nev., president. The deposit is about 20 miles by a gravel and dirt road southwest of Golconda, a town on U. S. Highway 40 and the Southern Pacific Railway, Pershing County, Nev. The deposit lies at an elevation of about 5,600 feet on the east flank of the north-south trending Sonoma Range. The property was leased by Messrs. Hollis Chatwin, T. E. Chatwin, and R. H. Richards of Salt Lake City and Mammoth, Utah. The lessees installed a crusher and erected an ore bin below the open cut on the deposit and mined and, shipped about 5,000 tons of about 30 to 52 percent manganese ore to the Columbia Steel Co., Provo, Utah.

Jan 1, 1950