Search Documents

By Roger A. Dworak

This report describes in detail the work done on the development of the Time Domain Reflectometry Microcomputer (TDRM). Modifications to the FMC-Model 302A Cable Fault Locator is described in Appendix D. The TDRM unit uses an 8080 microcomputer to accurately locate major faults in low capacitance cables to within ± 1 foot when properly calibrated. Major faults in high capacitance cables are usually located within ± 5 feet. The upper limits of fault detection are <1 kilohm shunt fault and >7 ohm series fault. In practice fault detection limits are reduced to <300 ohms shunt fault and >30 ohms series fault because of discontinuities caused by cable repair.

Jan 1, 1977

By Michael J. Beus, Stephen Iverson

BACKGROUND A mine shaft is the lifeline to underground mines. Mine operators depend on safe, uninterrupted, and efficient movement of workers and materials. The shaft and hoisting system provides access to the network of openings used to recover the underground resource, provides vertical transport of miners and materials, and serves as an escapeway in case of an emergency. Accidents involving hoisting can be catastrophic. Such was the case in 1973 at the Markham Colliery in Derbyshire, UK when the conveyance overwound and fell to the shaft bottom, resulting in 17 deaths. Hoist and elevator machinery must meet the requirements specified in the Code of Federal Regulations (CFR), Parts 57 and 75. According to the Mine Safety and Health Administration (MSHA) data, many shaft-related accidents in the United States are associated with the hoisting cycle. MSHA statistics show that there were about 1500 shaft- related accidents in the 5-year period between 1992-1996. Most of these accidents resulted from the action, motion, or failure of the hoisting equipment or mechanism and involved movement of the conveyance which includes cages, skips, ore buckets, and elevators. A hoisting hazard may be characterized as an "unsafe hoist operating condition caused by insufficient or inaccurate information available to the hoist operator" (authors&apos; quote). Earlier investigators have defined safety features and operating and maintenance standards for hoists, and reported on monitoring and control systems and sensors for hoists and conveyances [Farley, 1983; Ward, 19931. However, despite the considerable technological progress and hoisting control improvements in recent years, safety- related issues that require further investigation still remain. The hoist operator must constantly be aware of two important hoist-operating conditions: the position of the conveyance and the tension in the hoist rope. If this information is not available or is inaccurate, the hoist becomes unsafe. Current technology provides this information indirectly from sensors and indicators in the hoist room. However, unlike a building elevator hoistway, mine shaft hoistway problems often include: 1. poor ground conditions and excessive shaft wall and guide displacement; 2. rock bursts in deep mines (resulting in large rock movements and fragments blocking the hoist way); 3. water, ice, and salt buildup (impeding the smooth flow of the conveyance); 4. severe vibration from hoisting (resulting in loose guide support brackets, broken welds, or other alignment and conveyance mechanism malfunctions). The second issue relates to dynamic rope loads applied during normal winding, particularly during loading, acceleration, and stopping. Safety factors on wire rope are based on static load. They are artificially high to account for all cases of dynamic loads, even though the total load history on the rope (static and dynamic) during service is unknown. Therefore the tension, and thus the compliance with wire rope load safety factors, is unknown to the hoistman.

By R. V. Lundquist, H. Leitch

Sodium aluminate is the principal aluminum compound formed in the sinters prepared by the lime - soda sinter process for recovering aluminum from silicate source materials . The properties and characteristics of this compound were studied to improve the efficiency of the process . Crystalline sodium aluminate was prepared by sintering stoichiometric quantities of soda ash and calcined alumina for 1 hour at 1,250 ° C. The extent of aluminum extraction from sodium aluminate was determined in water and in solutions of NaOH and Na₂ CO3 . Nearly complete extraction of aluminum from sodium aluminate was achieved only in solutions containing free NaOH in excess of that supplied by the salt through hydrolysis . About 42.2 to 68.8 percent of the aluminum was extracted in water or in solutions of Na₂ CO . The precipitation of alumina trihydrate from sodium aluminate solutions was shown to be part of a continuous , reversible reaction according to the equation Al (OH ) A1 (OH )3 + OHThe reverse reaction dissolves alumina trihydrate in NaOH solutions to produce sodium aluminate . Approximate equilibrium concentrations were determined for the reaction at 30° , 50 ° , and 70 ° C. False apparent equilibrium conditions for the dissolution reaction appear when only a small excess of alumina trihydrate is present in the NaOH solutions . A large excess of alumina trihydrate must be present before the true equilibrium point is assured . The engineering significance of the data is summarized , showing controls that should be exercised for a successful and efficient process .

Jan 1, 1964

In 2004, a total of 741 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA). These mines (e.g., potash, gypsum, salt) comprised 5.1% of all operations.

Sep 1, 2007

By H. R. Pierce

A gas well has a certain definite capacity to deliver gas from the gas sand through the producing string of pipe. This capacity depends upon the pressures in the sand; that is, a well will deliver gas at a rate of flow which is determined by the formation or "shut-inn pressure in the sand and the back pressure at the face of the sand in the well. The three factors, rate of flow, formation or "shut-in" pressure, and the back pressure, for a given well, can be written into a fundamental relation which is strictly applicable only to that well. This relation can be used to determine the capacity of the well to deliver gas from any formation pressure against any back pressure held at the f ace of the sand in the well. Studies have been made of the deliveries of 400 gas wells operating under different conditions of pressure, Most of the wells which have been studied are in Osage County, Okla.; however, several representative studies have been made on wells in southern Louisiana, southern Texas, the Texas Panhandle, and West Virginia.

Jan 1, 1929

By A. B. Pederson, G. E. Bartlett

As a part of our study of how coal mine dusts injure the lung we have studied the effects of dusts and dust-exposed pulmonary alveolar macrophages (PAMs) on the growth of lung fibroblasts (LF). Fibroblasts were cultured near confluence in low-serum medium, either alone or in the presence of dusts, dusts plus PAMs, dust leachates or superriatants of dust-exposed PAM cultures. We report here provisional conclusions, based on initial observations. Rat LF were relatively unresponsive to direct effects of dusts, showing weak stimulation in only a few cultures, and there was no evidence that dust-exposed rat PAMs had released any growth-regulatory products. In contrast, guinea pig cells were more responsive to the dusts. The pattern of responses was quite complex. Three of the dusts stimulated LF directly (with no mediation by PAMs). Two dusts were essentially inert when added directly to fibroblast cultures, either with or without PAMs, but their leachates were active: 867 leachate was inhibitory and RF leachate was stimulatory. Dust 1361, either directly in the cultures or as an aqueous leachate, was stimulatory, and it activated cocultured PAMs to stimulate LF growth; however, supernatant products of 1361-stimulated PAMs were inhibitory. Direct exposure to 1192 stimulated LF, but its leachate was inert; cocultured PAMs exposed to 1192 had weak stimulatory effects, but supernatants of 1192-exposed PAMs were mildly inhibitory. MP3-3 had effects similar to 1192, except that the cocultured, dust-exposed PAMs had no effect on growth. We conclude 1) that guinea pig lung cells are more responsive to dusts than are rat lung cells, 2) that dusts can influence growth of LF by four kinds of interaction (by direct dust-cell interaction, by release of soluble dust components into the culture medium, by activating P AMs to exert direct cell-cell interactions, and by activating P AMs to release growth regulatory products into the culture medium), 3) that each kind of interaction may be neutral, inhibitory or stimulatory, depending on the dust tested, 4) that four of the dusts tested were neutral, inhibitory or stimulatory, depending on the assay (the fifth <lust was either neutral or stimulatory), and 5) that the effects of soluble mediators (leachates or products of activated PAMs) frequently did not correspond with the direct dust-cell or PAM-fibroblast effects. These results suggest that the nature of the dust-lung interaction at the level of cells and molecules is exceedingly complex. These observations need to be confirmed and extended to determine what characteristics of the dusts determine the nature of the cellular responses, and to determine which patterns of responses are detrimental and which are beneficial in the overall health of the dust-exposed lung.

Mar 1, 1989

By W. S. Landers

Nine high-volatile bituminous Utah coals were carbonized singly and in blends with low-and medium-volatile bituminous coals. Of the 9 coals, 2 are in commercial use as the base coals in blends that produce industrially accept-able metallurgical coke, while 7 are regarded as weakly coking and are not used commercially in coking blends. The carbonization tests were made in a la-inch diameter, cylindrical retort, using 50-pound charges. Sunnyside coal blended with autogenous char generally produced larger and stronger coke than was yielded by straight Sunnyside coal. The volatile matter of the char and the concentration of the char in the blend appear to be important parameters influencing coke size and strength. A blend of 10 per-cent autogenous char of 7.2-percent volatile matter with Sunnyside coal yielded coke that was larger, stronger, and of higher apparent specific gravity than coke produced from an industrial coke oven blend consisting of 15 percent medium-volatile coal and 85 percent Sunnyside coal.

Jan 1, 1967

By P. A. Cox

Guidelines are provided for the design of explosion-proof electrical enclosures that will meet MSHA certification requirements according to Part 18, Title 30, of the Code of Federal Regulations, and fulfill their intended service underground. The guide covers only those aspects of design which affect enclosure strength, ruggedness, endurance and flame path, i. e., the enclosure ability to properly contain an internal explosion. Internal static and explosion pressures, external impact and thermal heating load are treated as well as the proper selection of materials and welding procedures.

Jan 1, 1985

The combined production value of natural abrasives, which consist of tripoli, special silica stone, garnet, and emery, decreased in 1985. Shipments of processed tripoli increased slightly in quantity but decreased 6% in value, Production of garnet, an abundant iron-aluminum silicate, increased 24% in quantity and 20% in value. There was an 11% increase in the quantity and a 7% increase in the value of refined garnet shipped when compared with 1984 shipments, a new record high. Production of crude special silica stone decreased 10% in quantity and 14% in value, and shipments of finished special silica stone products decreased 85% in quantity and 68% in value. Both the quantity and value of special silica stone finished products sold or used were the lowest since 1981. Production of emery, an impure aluminum oxide, decreased 56% in quantity and 61 % in value of product mined and shipped. [ ]

Jan 1, 1987

By S. B. Bealko

Mining haul trucks comprise the majority of the equipment used in underground limestone mining operations and are known to emit high levels of noise. A previous study conducted by the National Institute for Occupational Safety and Health (NIOSH) indicates that 70-90 percent of all miners have a noise-induced hearing loss (NIHL) great enough to be classified as a hearing disability by retirement age. These results demonstrate the public health need to protect the hearing of workers in the mining industry, including haul truck drivers. Cab enclosures present an opportunity to isolate the haul truck operator from both truck and other noise in the mining environment. A total of twenty-five haul truck cabs were studied which were divided into three style (treatment) categories determined by soundproofing features and technology for noise reduction: old-, new-, and retrofitted-style. This study examines the contribution of cab acoustics, operator performance, and maintenance to noise reduction for each cab style. Dosimeters were used to measure 8-hr time weighted average sound pressure levels (TWA8 SPLs) inside and outside the cabs to determine if different acoustical treatments affect cab attenuation. Adherence to the Mine Safety and Health Administration (MSHA) Permissible Exposure Limit (PEL) of 90 dB TWA8 (with a 90 dB threshold) was used as the main indicator of overall noise reduction achieved. Dosimetery results indicate only 2% of the samples exceeded the PEL, but samples could still be reduced much further. Descriptive and comparative statistics indicate that noise levels inside the new-style cabs are significantly lower than the other two cab styles. Also, data suggest that there is no difference in noise exposures when comparing the old-style to retrofitted cab styles. Operator influence (opening doors and windows) was a significant factor for increasing noise exposure. This paper demonstrates that properly designed cabs can achieve major noise reductions, but noise levels could still be reduced much further below the MSHA PEL. New-style cabs, equipped with modern noise-reduction treatments, exhibit much lower noise exposures than the other two cabs styles, and the effectiveness of the current noise-reduction treatments for retrofitted cabs is questionable. Haul truck driver observations indicate that improved noise exposure reduction training is needed. Finally, specific targets for future noise reduction research are suggested that will further contribute to the prevention of hearing loss for haul truck operators.

By Miyuki Morioka, Michael J. Griffin

Discomfort, annoyance, or interference with activities due to exposure to vibration is only expected if the vibration exceeds the threshold for the perception of vibration. When there is more than one vibration input to the body (e.g. at the hands, seat and feet), the sensation is first experienced at the location with greatest sensitivity. Knowledge of differences in the thresholds of perception for vibration at the hand, seat, and feet should assist the identification of sources of discomfort caused by vibration. Perception thresholds for vibration have been determined in several studies, but only a few studies have investigated perception thresholds in the horizontal direction for hand-transmitted vibration 1, 6 or whole-body vibration 4-5, and there has been little consideration of perception thresholds for the foot resting on a vibrating surface. This study determines absolute thresholds for the perception of sinusoidal lateral vibration, examining the effect of vibration frequency (8 to 315 Hz for the hand and foot; 2 to 315 Hz for the seat) and the effect of input location (the hand, the seat and the foot). Methods Three groups of twelve males aged between 20 and 29 years participated in the experiment. Subjects in each group attended an experiment to determine perception thresholds for lateral vibration via either a rigid handlebar (30 mm diameter) at the left hand (left hand), or a rigid contoured seat (250 mm x 150 mm), or a footrest at the left foot (30.5 mm x 10.5 mm with 10-degree inclination). For the non-exposed hand (right hand) or foot (right foot), a stationary handle and footrest with the same dimensions as the vibrating handle and footrest were provided so that the same body posture was adopted among the three groups of subjects. An up-down (staircase) algorithm was employed to determine thresholds in conjunction with a three-down one-up rule. A single test stimulus (2.0 seconds) was presented with a cue light illuminated during this period. The task of the subjects was to indicate whether they perceived the vibration stimulus or not. The threshold was calculated from the mean of the last two peaks and the last two troughs, omitting the first two reversals. Results The median absolute thresholds of the 12 subjects determined at each frequency for the hand, seat and foot are shown in Figure 1. A frequency dependence of the threshold contours within the investigated frequency range is evident, with similar shape to the threshold contours

Jan 6, 2006

By Edward L. McHugh, Stanley M. Miller, Jeffrey K. Whyatt

The point estimation method can be applied to the safety factor (SF) equation for any specified rock slope failure mode (such as plane shear, step path, or wedge) to obtain reliable estimates of the mean and standard deviation of the SF probability distribution. A gamma probability density function is recommended for modeling this probability distribution, because it allows only for positive values and is flexible enough to provide symmetrical shapes and right-skewed, exponential-type shapes for the SF distribution. The mean and standard deviation define this distribution, which then can be integrated numerically from 0 to 1 to obtain the probability of sliding, PS (portion of the SF distribution where SF < 1.0). The overall probability of failure, PF, for the potential slope failure mass is the joint probability that the rock discontinuities are long enough to allow kinematic failure (PL) and that sliding occurs along the rock discontinuities (PS); that is, PF = PSPL. This method for estimating the probability of sliding is extremely efficient computationally, and thus, expedites slope stability simulation routines used by NIOSH software to stochastically describe rock slope behavior and assist the engineer in designing catch benches for large rock slopes. Enhanced bench design translates into increased operational efficiency and safer working conditions in open pit mines and quarries.

Research personnel from the Bureau of Mines, representatives of the Mining Enforcement and Safety Administration (MESA), and members of the mining industry met with other Government and Industry representatives at three seminars held in Pittsburgh, Pa., November 4, 1975; St. Louis, Mo., November 6, 1975; and Denver, Colo., November L1, 1975, to discuss the results of Bureau-sponsored research on coal mine illumination. The program, aimed at developing suitable illumination systems fur the working; places of underground coal mines, covered hardware development and field evaluation and the status of proposed MESA standards and proposed MESA enforcement procedures. These proceedings contain the opening remarks to the seminars and eight technical presentations an various aspects of coal mine illumination.

Jan 1, 1976

By Sean Gallagher, William S. Marras, Alan S. Litsky, Velimir Matkovic, Deborah Burr, John Landoll

Study Design. Survival analysis techniques were used to compare the fatigue failure responses of elderly motion segments to a middle-aged sample. Objectives. To compare fatigue life of a middle-aged sample of lumbosacral motion segments to a previously tested elderly cohort. An additional objective was to evaluate the influence of bone mineral content on cycles to failure. Summary of Background Data. A previous investiga¬tion evaluated fatigue failure responses of 36 elderly lumbosacral motion segments (average age, 81 ± 8 years) subjected to spinal loads estimated when lifting a 9-kg load in 3 torso flexion angles (0°, 22.5°, and 45°). Results demonstrated rapid fatigue failure with increased torso flexion; however, a key limitation of this study was the old age of the specimens. Methods. Each lumbosacral spine was dissected into 3 motion segments (L1-L2, L3-L4, and L5-S1). Motion segments within each spine were randomly assigned to a spinal loading condition corresponding to lifting 9 kg in 3 torso flexion angles (0°, 22.5°, or 45°). Motion segments were statically loaded and allowed to creep for 15 minutes, then cyclically loaded at 0.33 Hz. Fatigue life was taken as the number of cycles to failure (10 mm displacement after creep loading). Results. Compared with the older sample of spines, the middle-aged sample exhibited increased fatigue life (cycles to failure) in all the torso flexion conditions. Increased fatigue life of the middle-aged specimens was associated with the increased bone mineral content (BMC) in younger motion segments (mean ± SD, 30.7 11.1 g per motion segment vs. 27.8 ± 9.4 g). Increasing bone mineral content had a protective influence with each additional gram increasing survival times by approximately 12%. Conclusion. Younger motion segments survive considerably longer when exposed to similar spine loading conditions that simulate repetitive lifting in neutral and flexed torso postures, primarily associated with the increased bone mineral content possessed by younger motion segments. Cycles to failure of young specimens at 22.5° flexion were similar to that of older specimens at 0° flexion, and survivorship of young specimens at 45° flexion was similar to the older cohort at 22.5°. Key words: biomechanics, low back disorders, fatigue failure, age, motion segments, vertebral endplate fractures, torso flexion, lifting, bone mass. Low back disorders (LBDs) are a major cause of both short- and long-term occupational disability in the United States, and it is clear that workers in certain occupations are more susceptible to LBD.2-5 Specifically, epidemiologic studies have shown that jobs involving heavy physical demands such as construction,2,3 mining,2,4 and farming,5 engender increased risk of back pain. These occupations are thought to experience high LBD rates as a result of their extreme postural and manual lifting demands. Studies have shown that jobs involving significant lifting 6-9 and jobs that involve frequent bending10-12 are associated with increased LBD risk. Workers in the mining industry, in particular, often have to lift heavy materials in restricted workspaces that compel torso flexion. An understanding of the impact of repeated loading of the spine in flexion on fatigue failure of spinal tissues is thus a critical issue for our research agency, which is concerned with reducing the pain and disability associated with LBD in the mining industry. It is well accepted that loads experienced by the spine during manual lifting tasks are sufficient to cause fractures in the endplates of lumbar vertebrae, particularly on repeated loading. 13-15 Endplate fractures may not be painful in and of themselves 16; however, evidence suggests that the process of internal disc disruption and disc degeneration may be initiated via endplate fractures. 16,17 It has been shown that endplate damage will alter the distribution of stress in the disc, resulting in buckling of the lamellas of the internal anulus.17 Once this process has been initiated, repeated spine loading will cause additional disruption of the anular fibers, resulting in formation of significant fissures or tears. 11-21 If these tears occur near or extend close to the outer portions of the anulus, a wound healing process is initiated, which involves infiltration of mast cells, macrophages, and re¬lease of cytokines and growth factors. 21 The presence of these infiltrates has been strongly linked to discogenic low back pain. 21,22 Indeed, for patients experiencing chronic low back pain, the prevalence of internal disc disruption is at least 39%,19 which represents the most

By Thomas O. Glover

Cameroon&apos;s mineral industry continued to be dominated by crude petroleum. The country&apos;s economic development depended on the production and export of crude oil. Oil output was estimated to be 56 million barrels in 1984 compared with 47 million barrels in 1983 and 39 million barrels in 1982. The country&apos;s only refinery processed approximately 16,000 barrels per day of crude oil in 1984, operating at slightly over 50% capacity. This volume, however, supplied the domestic need for motor fuel and heating oils. Cameroon&apos;s economy continued to expand despite problems and setbacks stemming from the attempted coup of April 6, 1984. Gross domestic product (GDP) growth in 1984 was 6.5%, the same rate as in 1983. Offshore crude petroleum production was the chief factor in the sustained economic growth. The country also maintained a relatively strong balance-of-payments position through oil exports. Investment, ranging up to 25% of the GDP, greatly contributed to sustained growth. The oil sector contributed approximately 14% to Cameroon&apos;s GDP in both 1983 and 1984.

Jan 1, 1986

The Thermo-MIE personal DataRAM dust monitor (pDR) is a light-scattering instrument approved for use in gassy underground mines by the U.S. Mine Safety and Health Administration (MSHA). However, the use of light-scattering monitors has been inhibited by concerns about inaccurate readings resulting from changes in dust size distribution and composition, as well as concerns about the impact of moisture in the mine air. Because of this concern, the National Institute for Occupational Safety and Health (NIOSH) evaluated the pDR using available data from laboratory tests and mine surveys. The data show that accuracy can vary widely from test to test and mine to mine. In most cases, the results can be improved by using a companion gravimetric measurement to adjust the pDR data.

Jan 1, 2006

By J. E. Urosek, K. L. Cashdollar, D. A. Beiter, G. J. Shemon

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research to evaluate explosion blast effects on mine ventilation stoppings at the NIOSH Lake Lynn Experimental Mine (LLEM). After mine explosion accidents, MSHA conducts investigations to determine the cause(s) as a means to mitigate or eliminate future occurrences. As part of these post-explosion investigations, the condition of underground stoppings, including the debris from damaged stoppings, are documented as evidence of the strength and the direction of the explosion forces. The LLEM data showed that a total pressure of 52 kPa (7.6 psi) destroyed the solid concrete block stopping, ~36 kPa (~5.2 psi) destroyed the hollow-core concrete block stopping, and 9 kPa (1.3 psi) destroyed the steel panel stopping. These results will assist investigators in determining the explosion forces that destroy or damage stoppings during actual coal mine explosions.

By W. P. Diamond, S. L. Cario, F. Garcia, J. D. Byars, T. P. Mucho

The National Institute for Occupational Safety and Health (NIOSH) has been conducting research at a Pittsburgh Coalbed longwall mine to evaluate and optimize bleeder ventilation and gob gas venthole longwall methane control systems. Gas flow into these two methane control systems was investigated using a combination of Sulphur Hexafluoride (SF6) tracer gas studies and gob venthole pressure monitoring experiments. The insights gained from this research has facilitated the development of along wall subsided strata methane control system conceptual model. This model provides the basis for design suggestions to increase the efficiency of the gob gas venthole system to permit the bleeder ventilation system to become a "safety net" for methane control.

By C. W. Smith

The U.S. Bureau of Mines conducted research to determine the effect of ground water control on the dewatering of phosphatic clay wastes. Two storage impoundments were constructed. One impoundment was surrounded on three sides with a series of well points (shallow vertical wells) to lower the ambient water table and the second impoundment served as a control. Ground water was pumped from the area surrounding the test impoundment for a period of 490 days. A constant pumping rate of 60 gal/min resulted in a water table drawdown of 13 ft, approximating the bottom of the impoundment. At the end of the test period percent solids in the test impoundment was 35 pct, while in the control impoundment percent solids was only 26.8 pct. Percent solids of greater than 30 pct is required for capping and final reclamation using fertile overburden.

Jan 1, 1989

By L. R. Burdick, J. F. Barkley

The inherent heating value or the amount of heat that will be produced when a coal is completely burned is measured in British thermal units (B. t. u.) per pound of coal . This standard heat unit is the quantity of heat required to raise the temperature of 1 pound of water 1 °F . at about 60 °F . The amount of inherent heat is determined by burning a small quantity of the coal in a heat meter or calorimeter , which gives results in British thermal units . The exact manner of making this test is standardized by the American Society for Testing Materials.4/ The value so determined is the total heat developed by complete burning, with all the products of combustion cooled down to the temperature of the calorimeter . The calorimeter is kept at about room temperature . This total heat is sometimes called the " high" or gross heat value , because it includes the latent heat given up by the water vapor in the products of combustion when the vapor condenses to water in the calorimeter . The heat as measured is reported as the heat of combustion at constant volume , since the burning is carried out in a tightly closed calorimeter chamber whose volume does not change . In actual use , coal is usually burned in an open - end chamber at constant pressure , generally somewhere near atmospheric . As the heat of combustion of coal at constant pressure is very slightly higher than the heat of combustion at constant volume , it might be considered that the heat at constant pressure should be used as the standard reference base . For an ordinary eastern coal the heat at constant pressure is about 16 B. t . u. per pound higher than the heat at constant volume . Calorimeter corrections , ordinarily not considered , that could have been subtracted from the heating value before reporting , may amount to about as much . Hence , the value reported is apt to be more nearly the true heating value at constant pressure than at constant volume .

Dec 1, 1941