Search Documents

By R. T. MacMillan

A number of chemical techniques have been applied to manganese ores from three areas of Aroostook County, Maine. Although large tonnages of these ores have been proved, they are low grade, and their exploitation has awaited a suitable beneficiation scheme. As conventional ore-dressing methods had failed to yield satisfactory results, attention was turned to chemical procedures. Leaching with dilute (7-percent) H2S04 extracted over 90 percent of the manganese from ore of the Dudley farm area, consuming 3.8 pounds of acid per pound of manganese extracted. Ores from the Littleton Ridge and Maple Mountain-Hovey Mountain areas were less amenable to this treatment, yielding approximately 80 and 60 percent of their Mn content, respectively. To increase the percentage extraction of manganese in the latter two ores, a number of factors were varied, including (1) acid concentration in the extracting solution, (2) ratio of acid to Mn in the slurry, and (3) preliminary heat treatment of the ore with a reducing agent. Other acids, including HNO3, HC1, and H2SO3, were tried also; however, no significant improvements in the Mn leached from Maple Mountain-Hovey Mountain ore were made. The manganese extraction of Littleton Ridge ore was raised to 90 percent by providing 9 to 11 pounds of HNO3 per pound of Mn in the ore.

Jan 1, 1954

By J. B. Zadra

Much has been published by various investigators on the use of activated carbon for adsorbing precious metals from cyanide solution and pulp. For the benefit of the reader, a list of these earlier publications appears at the end of this report. The present paper deals only with a process for extracting gold from gold-laden carbon and re-use of the de-adsorbed carbon. At the Getchell mine, Redhouse, Nev., experiments have been in progress for several years concerning the use of activated carbon to adsorb gold from their slime circuit pulp. The experimental work has been successful. Their practice has been to ship the gold-laden carbon to a smelter for treatment, which meant the total loss of the carbon in addition to smelter and freight, charges, all of which proved costly and wasteful.

Jan 1, 1950

By Ronald B. Hollenbeck

The value of mineral production in Alabama continued to increase and reached a new high of $260 million, 3 percent above the previous high established in 1967. Record high values were reported for bentonite, crushed marble, lime, miscellaneous clay, portland cement, salt, sand and gravel, and scrap mica. The value of coal, total cement, petroleum, and stone accounted for 87 percent of the State's total value of mineral production. Alabama ranked second among the States in the production of bauxite and scrap mica and third in kaolin, masonry cement, and native asphalt.

Jan 1, 1970

By Jeffrey S. Newman

This report presents a summary of the results of a four-phase program conducted for the Bureau of Mines to evaluate underground mine fire detection systems. In addition, Phase IV is presented in detail. The major accomplishments of this program are: 1) quantification and prediction of the distribution of fire products in a mine pas¬sageway; 2) quantification of "equivalent protection" by fire detectors as contained in Title 30 of the Code of Federal Regulations; 3) definition of detection criteria; 4) design of a detector test program for determining detector spacing requirements; 5) design, construction, operation, and calibration of a fire test apparatus for evaluating mine fire detectors; 6) quantification of several mine fire sources; 7) evaluation of several fire detector types including heat, CO and CO2 gas, and ionization smoke detectors; 8) development of generalized spacing criteria for mine fire detectors; and 9) development of performance specifications. Reports for Phases I through III are included in Appendices.

Jan 1, 1984

By Ovsei Volberg

Motion capture involves recording the position and global orientation of joint sensors of a real object, in most cases a real person performing some human activities. This information is usually recorded at uniformly spaced instances of time, or as it is often called frame-by-frame. Then the recorded motion data sets are processed and mapped into a skeleton hierarchy of a virtual, computer simulated human figure to control the motion of the virtual human in the computer simulation. In the first part of the paper we review several new techniques developed to facilitate the manipulation, noise reduction, storage and reuse of captured data, which have a potential to reduce the overall cost of motion simulation and improve its realism. In the second part of the paper we consider the real life problem of reducing a worker?s risk from being hit by underground mining machinery in a confined space. We formulate a set of requirements to motion editing for this particular task and analyze the limitation of existing techniques

Jan 1, 2000

By Dennis A. Hansen

As part of a U.S. Bureau of Mines program to develop a more continuous titanium metal extraction process that uses domestic resources, a study was made to determine the extraction of titanium (Ti) and iron (Fe) from New York rock ilmenite using fluosilicic acid (H2SiF6). The effects of leach temperature, acid concentration, and particle size were investigated for the rate at which Ti and Fe are extracted from the ilmenite. Within the leach time studied, the extraction data fit a shrinking-core model; the rate-controlling step was diffusion of H2SiF6 through an ash layer resulting from a heterogeneous leaching reaction. The rate is linearly dependent on the H2SiF6 concentration and is inversely proportional to the square of the particle diameter. Using 2.6M H2SiF6 at 85°C, 49% of the Ti and 53% of the Fe in 44-to 74-µm New York rock ilmenite were extracted in 3 h.

Jan 1, 2010

By Mark R. Pettitt

Noise surveys conducted in underground coal mines have consistently indicated that auger mining machines subject the operator and helpers to excessive noise exposure. The machine cutting heads have been identified as the primary noise source. This report documents the research program conducted to (1) investigate the nature of the cutting head noise problem, (2) develop noise control concepts, (3) devise in-mine survivable techniques to implement the noise control concepts, and (4) build and demonstrate prototype reduced-noise auger miner cutting heads. The dynamic forces generated during coal cutting by the brittle fracture of coal are predominently low frequency. The low-frequency (less than 1500 Hz) structural response of the cutting head, therefore, determines the noise radiated by the cutting head. The most feasible methods of reducing the cutting head low-frequency response are to increase both the structural stiffness and the low-frequency damping. A technique was devised to achieve these goals. The standard plate helix was replaced by a sand-filled hollow helix of triangular cross section, and the core diameter was increased with an attendant reduction in helix depth. Extended in-mine tests demonstrated the operational capability of the reduced-noise auger cutting heads. The simple noise control concepts are valid for all continuous miner cutting heads. The sand-filled hollow helix technique, which achieved a 10 dB(A) noise reduction for the auger, can be used on any helix-bearing Cutting head.

Jan 1, 1983

By A. E. Petersen

To reduce U.S. dependence on imports of titanium, the U.S. Bureau of Mines has investigated the recovery of titanium from perovskite (CaTi03). Domestic perovskite deposits represent a significant, but untapped, titanium resource. An acid sulfation method was developed that will extract about 97 pct of the titanium and the columbium and 70 to 90 pct of the rare-earth byproducts from perovskite concentrates. A flow-sheet for recovering titanium as pigment-grade titanium dioxide (Ti02) is discussed. Test work performed in developing each unit operation is described. The first three unit operations have been demonstrated using laboratory-scale continuous methods of operation: acid sulfation of perovskite concentrates, leaching sulfation residue to dissolve metal values, and precipitation of titanium oxysulfate monohydrate (TiOS04?HP) from the resulting leach flltrate. Batch testing of other unit operations was performed: TiOS04?H20 redissolution and iron reduction, precipitation of Ti02 by hydrolysis, and regenerating recoverable acid with rare-earth byproduct recovery. Cost evaluation results are provided, indicating that processing perovskite concentrates by acid sulfation may be an economically viable means of producing Ti02.

Jan 1, 2010

By Charles L. Kimbell

Virtually every available measure of total world mineral industry activity demonstrated that 1982 was little, if any, better for the industry than 1981 had been. Levels of production, trade, and consumption for virtually every major commodity declined; unit prices for most commodities fell, particularly in terms of constant dollars, and as a result of cutbacks in output and lower prices, capital available for investment within the industry was reduced. These conditions, coupled with the existence of considerable idle capacity, tended to retard investment, although there was an upturn in U.S. oil industry investment overseas. Despite the overall depressed situation of the world's mineral industry, there were indications of possible improvements in market economy countries near yearend, as output of some materials increased marginally and as prices for some mineral commodities reversed their downward trends. The downturns in total world mineral industry activity were not universal from the viewpoint of individual countries. Indeed, output of a number of commodities increased in centrally planned economy countries, and these gains were insufficient to offset declines in market economy countries, thereby sharply altering the proportion of total world output accounted for by each of these two groups of countries. There was a similar shift in consumption on a percentage basis.

Jan 1, 1984

By Ellsworth Y. Dougherty, Edwards F. Fitzhugh

"INTRODUCTION During the summer of 1945 the Bureau of Mines made approximately 200 miles of reconnaissance magnetic surveys in north-central Mirnesota. The survey started near the western end of the Mesabi Iron Range and extended into the area to the southwest, west, and northwest and also southward to the-northern limits of the Cuyuna Iron Range. The purpose of the survey was to data to assist exploration for iron ore in the region through:1. Supplying a relatively unit form network of traverses, by which and future surveys of localities in the urea ray be correlated. Suggesting localities in which more detailed magnetic surveys may be justified, and, Disclosing localities in which there is lass hope of obtaining significant results from further magnetic surveys.The instrument used was a Hotchkiss Superdip, and traverses for calibration and comparison were run with a Schmidt-type magnetometer. Field observations and work directly related thereto were carried out under contract by E. J. Lang-year Co., Minneapolis. Engineers of the Bureau of Mines planned, directed, and reviewed the survey."

Aug 1, 1946

By G. S. Rice, R. V. Wheeler

"In September 1923, a proposal was made through official diplomatic channels by the British Safety in Mines Research Board to the United States Bureau of Mines for ""closer cooperation between the two countries in investigations into the causes and means of prevention of mining dangers."" This proposal was cordially accepted by the Bureau of Mines and was officially approved.In the spring of 1924 cooperation was .formally begun. It contemplated, as stated officially, ""full exchanges of information, a joint program of research, and periodic exchange of personnel so as to assure concordant results. By making the resources of both organizations available it will hasten the attainment of results, will secure better: checks for, accuracy, and in the end will save money for both by avoiding duplication and repetition.""This joint work has been carried-on successfully since that time and has developed valuable results, reports on which have been issued from time to time. The progress report which follows gives the results of the studies and work carried on in 1929.During 1929 all the phases of our cooperative research, begun in previous years, have developed normally. The exchange of formal monthly reports on all programs of mutual interest has been continued and has proved an invaluable, means of maintaining contact between the investigators of both organizations. There has been no diminution in the exchange of routine progress reports on specific subjects or in direct correspondence. The interchange of personnel has been maintained, and we can say that the mutual benefits to be derived from this form of cooperation are so great as to be difficult to overestimate. It leads to an appreciation of methods of research and modes of thought in the interpretation of results obtainable in no other way, and engenders a frankness and intimacy which must continuously enhance the value of future cooperation.Dr. S. R. Katz, who was assigned for service with the Safety in Mines Research Board in April, 1928, returned to America in May, 1929. During his stay in England he completed, in cooperation with members of the board's staff, the equipment of a gas-mask laboratory and designed and tested a new form of gas-mask canister. A publication of the Safety in Mines Research Board dealing with this investigation has been prepared and approved and will .be .issued in the near future. In additions Dr. Katz imparted to those with whom he was associated much of his knowledge and technique regarding his particular subjects. He delivered two lectures to the board's staff, the subjects be ""Gas Masks"" and ""The Intensity of Odors"", and gave papers before the Midland Institute of 'lining Engineers and the Birmingham University Mining Society on the subject of ""Industrial Gas Masks""."

Jun 1, 1930

By Forrest T. Moyer

The safety record of the mineral and mineral-fuel mining and processing industries in 1966 was improved slightly for the second consecutive year as indicated by reduced injury-frequency and injury-severity rates. The overall operating activity was higher in 1966, as measured by the increased number of men working and the total man-hours of worktime. Injury Experience.-The rate of occurrence of all disabling work injuries in the mineral industries was 17.38 per million man-hours in 1966. This overall rate comprised frequencies of 0.28 for fatal and 17.10 for nonfatal work injuries, compared with respective rates of 0.28 and 17.26 in 1965. Fatalities totaled 543; 5 more than in 1965. The total of 33.091 nonfatal injuries was 291 higher than in 1965. However, the larger number of disabilities was offset by the increased worktime in 1966. so that the fatality frequency was unchanged and the nonfatal frequency rate decreased from 1965.

Jan 1, 1967

By W. W. Agey

An inexpensive technique that laboratory studies indicated would significantly reduce seepage in irrigation canals was devised and tested through research sponsored by the Bureau of Reclamation and the Missouri River Basin Field Committee. Laboratory tests simulating optimum field conditions determined that easily applied sodium carbonate solutions made test beds of canal lining materials virtually impermeable for long periods. The study comprised alternative laboratory treatments of 3-inch-deep test beds of canal earths with 74 water-soluble chemicals in search of one 01' more that would effectively improve the water barrier characteristics of the component clays. Sodium carbonate, one of the least expensive, was among the most effective. The addition of 0,4 lb of reagent per sq yd greatly reduced the seepage from typical, highly permeable test beds. The reagent penetrated and sealed surface for about a 1.5-inch depth.

Jan 1, 1965

By Arthur Matzick

The oil shale from the Mahogany zone of the Green River formation in northwestern Colorado has the greatest potential in the United States for early utilization. A large reserve of adequately rich shale is available to support a sizable industry, and crushing of tremendous tonnages will be required if conventional processing methods are used. This report presents Bureau of Mines data on crushing experiments, physical properties, and related information for Colorado oil shale. Among the properties important to crushing are slab-forming tendency, resilience, slippery character of the richer grades, and heterogeneous nature of an average charge of Colorado oil shale.

Jan 1, 1960

By W. I. Nissen

As part of its program to provide technology for reducing undesirable environmental impacts of mineral processing operations, the Bureau of Mines developed the citrate process for desulfurizing industrial stack gases that contain from 0.1 to 2 vol pet S02. In this regenerable flue gas desulfurization (FGD) process, S02 is absorbed from cleaned and cooled industrial flue gas with a citric acid-sodium citrate solution. The absorbed S02 is subsequently reacted with H2S to precipitate marketable elemental sulfur and regenerate the solution for recycle. Laboratory investigations of process parameters provided information for designing larger scale continuous operations. Information gathered from operation of two pilot plants, one at a copper smelter and one at a lead smelter, confirmed the laboratory results. Data were obtained for design and construction of a commercial-sized demonstration plant at the George F. Weaton Power Station, Monaca, PA. A preliminary operation of the plant was demonstrated, under a cost-sharing Bureau-industry contract. This bulletin describes the citrate process and gives results of the laboratory, pilot plant, and demonstration plant studies, as well as corrosion investigations.

Jan 1, 1985

By R. J. Burgess

During World War II the shortage of ore revived interest in eastern iron deposits, among which -!2..c "Ile Massachusetts and Connecticut limonites. The Cheever mine, in the Richmond-Salisbury area of Massachusetts, was formerly a large producer of limonite ere. The Bureau of Mines investigated the lateral and downward extensions of the Cheever ore body, which was mined from about 1850 to 1892, by ap open cut 1,000 feet long and also by underground workings. even holes aggregating 1,723 feet, were drilled by the Bureau during the winter of 1943-44. They comprised three diamond-core drill holes, two churn-drill holes, and two rotary-drill holes. A geophysical survey of the Cheever mine area and adjoining ground was made in conjunction with the drilling program. Although this survey did not locate the limonite ore beds, the data were of considerable assistance in locating the limestone contact which forms the footwall of the ore beds. Drilling disclosed two beds of limonite with a heavy overburden of glacial till.

Jan 1, 1949

By Stephenson. E. L.

"INTRODUCTION In the spring of 1942 a series of magnetometer surveys on deposits of black sand underlying Pleistocene raised marine terraces along the coast of southwestern Oregon was nada by the Division of Geophysical Exploration of the Federal Bureau of Mines in cooperation with the Oregon Department of Geology and Mineral Industries. A few preliminary tests had been made in the same area in May 1940 and December 1941.The sands contain fine gold and metals of the platinum group, and, beginning in 1852, extensive, but spasmodic mining and exploration have been done for these precious metals. There are many old placer, mines and prospects, although for the most part the yield of the metals has been small. The sands also contain other minerals of potential value, including ilmenite, magnetite, garnet, zircon, and particularly chromite, and the wartime demand for domestic chromite resulted in extensive testing and development of the known deposits. The purpose of the magnetometer surveys was to determine the efficacy of, magnetic methods in tracing and outlining these known deposits and in prospecting for new ones. The field work was done between March 17 and May 29, 1942, by the author assisted by W.W. Paulsen of the Oregon Department of Geology and Mineral Industries."

Jun 1, 1945

By Constantine C. Popoff

The Hermada antimony deposit is in the Sewtooth Range in southwestern Idaho, about 77 miles by road northeast of Boise. Stibnite mineralization occurs over an area one mile wide from west to east and two miles long. It is locally referred to as the Swanholm district. In 1947 high- grade stibnite ore was discovered on the East Fork of Swanholm Creek. Since then, ore in commercial quantity has been produced by the Hermada Mining Co. The total output for 1947-50 was about 5,000 tons of ore, containing 640 short tons of antimony metal.

Jan 1, 1953

By John J. Henn

An economic evaluation was made of the Bureau of Mines incinerator residue separation process to update the one published in 1971 to a mid-1.974 cost basis. This evaluation includes a modification of the glass-recovery operation used In the original plant design as well as a unit to bale the ferrous scrap product before shipment. Products from the plant are ferrous metal, aluminum and copper-zinc scrap, and a mixed-color glass cullet. The estimated capital and operating costs for four plant sizes are as follows : [ ] The operating costs do not include credits for recovered metals and glass.

Jan 1, 1975

By R. Karl Zipf, Z. T. Bieniawski

"Fracture mechanics plays an important role in studies of geologic materials such as rock and coal. Yet fracture data are scarce for rock and most limited or unreliable for coal. A testing system was developed which can apply mixed mode loads to a crack tip in many rocks and geologic materials. It is possible to subject the test specimen to pure mode I, various mixed modes and a nearly pure mode II fracture load. The system is currently used to study the mechanics of fine fragment formation in various coals. Experimental measurements include KI and KII' fracture velocity and acoustic emission.INTRODUCTIONA major research program at The Pennsylvania State University is directed to understanding the fundamental mechanics of fine fragment formation in various coals. The program represents an effort to reduce the incidence of coal workers pneumoconiosis (black lung) in coal miners. The principal source of the respirable coal fragments is the cutting operation which forms and liberates the particles by a fracture process. Present understanding of the mechanics of the events which form and liberate these particles is meager (Cook, 1982).Current knowledge of the fundamental mechanisms of coal dust generation and entrainment in terms of the underlying fracture mechanics is critically needed to improve and possibly control the processes involved. Whether the cutting operation is done with a 'continuous miner' cutting machine, a plow or a longwall shearer, it is fundamentally a problem of mixed-mode crack propagation. When a cutting tool interacts with coal, it causes numerous cracks to propagate through the intact material. Numerous larger fragments are broken free, but another quantity of undesirable fine fragments is also created. The formation of these respirable fragments may be a direct result of the crack propagation process; hence, a thorough understanding of the fracture mechanics of coal is required to minimize production of the unwanted fine fragments.In most rock engineering applications, the rock material properties are of secondary importance to the rock mass properties; however, for rock fragmentation and rock cutting problems, it is rock material properties such as fracture toughness which are of prime interest (Bieniawski, 1980). Several rock cutting and rock failure theories have been proposed, but it is only very recently that fracture mechanics concepts have been successfully applied to the study of rock cutting mechanics. All cutting models seek to predict the cutting forces and the cutter geometry necessary to cause rock breakage and chip formation given some fundamental mechanical properties ~f the rock. Such models have wide applications in drilling, tunnel boring and mining problems. Nelson et al., (1985, 1986) has provided a very useful correlation between the laboratory measured fracture mechanics properties of rock and the performance of the disk cutters on tunnel boring machines."

Jan 1, 1989