Search Documents

By R. E. Heithecker, D. B. Taliaferro

"INTRODUCTION Recovery of core specimens from subsurface formations and their subsequent analysis are important aids in efficient development and operation of oil and gas fields. Gore specimens first were obtained mainly for the geologic information they revealed; now they are analyzed to determine many of the physical characteristics and conditions of the subsurface formations as well. Cores recovered from the producing formations may be analyzed for porosity, permeability, oil content, ""connate"" water content, and other physical and chemical properties of the formation, all to the end of furnishing enough data for making reliable estimates of the quantity and avail¬ability of oil and as within a reservoir and in devising efficient means for their withdrawal.Examination of bottom-hole samples of oil gives valuable information concerning the amount of gas in solution in the oil within the reservoir and the resultant shrinkage of the oil when the gas is released. Producing characteristics of reservoirs nay be determined by means of subsurface pressure and temperature gages and measurements male at the wellhead; however, unless reliable core analyses are available, these data have only limited use in any quantitative study of reserves. In such a study the quantity of oil, gas, and water contained in a unit volume of the reservoir formation is extremely important. Although reliable methods of analyzing cores have been developed and the data thus obtained are valuable, their applications become more limited or reservoirs at higher temperatures and pressures are discovered. This condition results almost entirely from the fact that in recovering a core from a formation of high pressure and temperature by present methods a large part of the fluid content of the core is lost or contaminated to an unknown extent. For a number of years most petroleum engineers have held that if this loss and contamination of the fluid content of a core were eliminated, the value of core analyses would be increased greatly."

Nov 1, 1939

By Peter Grandone, Ludwig Schmict

The injection of oil-field brimJs into subsurface formations containing mineralized water ·now is .recognizud as the most satisfactory and effective means of disposal in Kansas.· Other disposal ·methods, such as impounding brines in evapOTation nonds and controlled diversion into surface streams, have not prov-ed entirely successful, principally. because the volumes of brine to be disposed of were large, the soil f;?xtr~~mely porous, the net evaporation is low, and the rairiiall insufficient fc)r adequati.:~ dilution of the brine. The disposal of brine by subsurfaCE) inj'ection is often: more. expensive than by either of the above surface methods; nevertheless, surface dis:pos?,l ow.ing to the damaging effe-c.ts of· salt water to plant, animal and aquatic life and to potable water supplies has been:a long-continuing problem with many technical, economic, and 'legal·complexiti,2s

Aug 1, 1943

By L. A. Stinnett

An investigation of hazardous surface openings of abandoned and inactive underground mines in the Black Hills area of South Dakota has revealed: (1) tracing legal ownership of mineral claims via county courthouses is confusing, complex, and oftentimes misleading, (2) in general, the selected mine openings in this investigation are to be considered relatively high in risks and hazard potential which poses a threat to the general public, (3) mine closure procedures and designs can generally be categorically implemented depending on the overall situation of the particular mine opening with subsequent unit costs estimates, (4) few preventive state or federal legal measures exist to date concerning mine closures, and (5) liability damages relating to mine opening accidents usually involve expensive and complex common law cases.

Jan 1, 1979

By J. L. Holman

The Bureau of Mines is conducting research to recover strategic and critical metals such as Ni, Co, and Cr from mixed contaminated super-alloy scrap. One approach being studied involves melt refining of superalloy scrap to produce anodes for electrolytic deposition of Ni-Co alloy. This melt refining of superalloy turnings is described based on melt-oxidation and oxidation-carburization experiments, using roasted superalloy grinding sludge to supply the 0 needed to oxidize Cr and other readily oxidized elements to the slag. Controlled melt-carburization subsequent to oxidation improved the metal phase recovery of Ni and Co to well over 90 pct and decreased electrolytic solubility of Cr, Mo, and W by carbide formation. Electrolytic refining experiments were conducted using a controlled-potential mode (preset cathode potential). Data show effects of Fe and Cr impurities, cation concentration, electrolyte pH, S04-Cl electrolyte ratio, temperature, cathode potential, and cation-selective membrane use on current efficiency, current density, and deposit composition. Disposition of Ni, Co, Cr, MO, W, and Fe is compared for melt-oxidized versus oxidized-plus-carburized anodes. Deposits containing >97 pct Ni + Co (major impurity Fe) have been routinely obtained from scrap anodes. Research is continuing to improve deposit quality in sustained deposition and to recover Cr and other metals from refining slags and anode sludges.

Jan 1, 1986

By L. A. Morley

Volume IV of the final report examines the problem of indirect contact of overhead high-voltage power lines by mining personnel. This refers to the contact of energized lines by workers through some intermediate conductor such as a metallic tool or a piece of high-reaching mobile equipment, thus the term "indirect contact." The shock hazard presented by such contact has been a major cause of electrical fatalities associated with mining operations. The report volume is divided into three major areas. The first gives a general background of overhead lines, basic characteristics, and associated hazards, and continues to describe presently used techniques and devices which attempt to alleviate the contact problem. The second area narrows the discussion to the mining industry by presenting a detailed analysis of 39 overhead-line contact accidents in mining since 1970. The third major section uses the information from the first two areas to formulate recommendations to prevent these accidents and subsequent electrocutions at mining operations.

Jan 1, 1982

By R. B. Ladoo

"Present Situation:At the beginning of 1920 a general feeling of optimism was noted in many talc-producing districts. The industry seems to have recovered from the temporary depression of the first half of 1919 and many mills are running at capacity production with their entire output for 1920 contracted for. The imports of talc for 1919 were only slightly larger than in 1918 by weight and probably no more by value. Thus foreign competition has not begun to be seriously felt. Several new companies in this country have been organized, some to operate new deposits and others to continue the work done by others.An interesting phase of the present situation is the possibility of increased use of talc in paint. There is a shortage of barium sulfate used as a paint filler. Since, for some uses, talc is considered second only to BaSo4 as a filler for paint, it is possible that part of the shortage could be relieved by an increased use of talc.A series of physical tests upon all pigment materials used in the manufacture of paints is being conducted for the Paint Manufacturers Association of the United States. It is important that all types of talc be represented in these tests. Producers of finely ground talc, 200 mesh and finer, are urged to submit samples of at least two pounds each of these grades that are available to paint makers with trade name and quality data, to the Institute of Industrial Research, 19th & B Streets, N. W., Washington, D. C., where the tests are being conducted."

Jan 1, 1920

By C. A. Taylor, C. E. Munroe

"In blasting the explosion of the high explosives charge is initiated by means of a detonator. Consequently the successful operation of the whole system is, ab initio dependent upon the suitability and efficiency of the detonator used. A considerable number of methods for testing the efficiency of detonators have been devised. In a previous publication*** of the Bureau of Mines many of these were discussed after having been classified as direct and indirect methods.In 1910, W. O, Snelling, then explosives chemist of the Bureau, devised a direct method which depends on the extent to which a hard brittle material of uniform granulation, such as quartz sand, is pulverized by the explosion of the detonator when imbedded in it, and, as a container in which to carry out the tests, he devised the vessel known as the Bureau of Mines sand-test bomb No. 1. A brief mention of his work was made in a paper presented to the Engineers' Society of Western Pennsylvania.****Later Storm and Cope made a very extended investigation of this method using sand-test bomb No, 1. Their paper***** contains a detailed, illustrated, description of sand-test bomb No. 1, with precise specifications of the sand and a minute account of the technique followed, together with a discussion of the data they obtained from the tests in this bomb of 112 detonators representing each of the grades from We, 3 to No. 10, inclusive. The average of results obtained by them are set forth in the following table."

Dec 1, 1923

When the Organic Act of 1910 established the Bureau of Mines within the Department of the Interior, the Bureau's programs involved only health and safety research and education, and fuels testing. As the Federal Government's primary agency for research in minerals, the Bureau has expanded its scientific and technological investigations to mining, processing minerals substances, eliminating occupational health and safety hazards in the mineral industries, economic development, and resource conservation. Today, Bureau activities cover a broad spectrum of programs for meeting the diverse (and sometimes conflicting) needs of mineral industries, government, and the public. In the 1960's, the Bureau initiated programs to resolve environmental problems associated with past mining and mineral processing. In the 1970's, the energy crisis raised the national consciousness concerning our limited supplies of domestic mineral and fuel resources. Dependence on foreign sources of raw materials critical to our national economy and competition from other countries for these world supplies stimulated the need to conserve and use with intelligence the Nation's minerals, metals, and fuels.

Jan 1, 1976

By Fred D. Wright

The objectives of this research were: 1. to determine the stability relationships of coal mine roof rocks which are cut by fractures or intersecting joints with and without roof bolts, under various sets of conditions including horizontal formation pressures, inclination and coefficient of friction of joints, bolt loads, roof spans and rock properties; and 2. to develop criteria for the design of roof bolt sys terns for such roofs. The problem was studied by mathematical finite element models and by laboratory models. From the results of the mathematical and laboratory models, equations were derived to express the relationships listed above for cracked, single-layered roof beams and design tables for such beams are included. The analysis was then extended to include multi-layered cracked beams reinforced by roof bolts and a method for analyzing and designing bolting patterns for such roof rocks is presented.

Jan 1, 1974

The following is a Maintainability Design Checklist for coal mining equipment. The purpose of the checklist is to provide a summary of design review points for the maintainability assessment of new or existing underground equipment. It specifically focuses on the identification of equipment design features, tasks, or procedures that impact equipment downtime, repair costs, labor hours and maintainer skill level requirements. Some checklist points are general in nature. The checklist was designed to be used across all categories of underground equipment. The intent is to draw attention to design features and maintenance procedures that will increase maintainability requirements. You are encouraged to adapt this checklist to site specific or machine specific requirements by: ? Inserting specific performance criteria for various categories of maintenance tasks. For example; all hydraulic lines on a shuttle car should be replaceable in 15 minutes or 25 minutes, etc. ? Adding or deleting checklist items for different categories of equipment. You would include environmental control equipment, for example, on face equipment and not on shuttle cars or man trips. ? Adding additional checklist items based on site or equipment specific maintenance histories or experience, company maintenance standards, or other factors.

Jan 1, 2000

By Joseph J. Wallace, William H. Tavenner, D. A. Reynolds, John M. Provost, James J. Dowd, R. F. Abemethy

"CONCLUSIONSThe investigation shows that there are 5 coal beds of major importance in Wyoming County from the standpoint of present production - Pocahontas No. 3, No. 2 Gas, Sewell, Beckley, and Eagle - and 5 beds of minor importance - Pocahontas No. 6, Cedar Grove, Winifrede, Douglas, and Chilton. The Pocahontas No. 3 bed contains the largest remaining known reserves.Known measured and indicated reserves in all beds, based on a minimum thick¬ness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 2,665 million short tons as of January 1, 1951. Of this total, 2,121 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.Recoverable reserves of coal have been estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Wyoming County, as determined by this investigation, is 55.0 percent. This percent¬age is based on the total thickness of coal (less partings 3/8 inch or more thick) in the bed rather than on the thickness of the coal mined. The known recoverable reserves are estimated to be 1,167 million tons as of January 1, 1951.4. Since most of the Wyoming coals are medium- and low-volatile bituminous in rank and expand during carbonization in modern ovens, they are blended with high-volatile contracting coals."

Apr 1, 1953

By Lewis M. McNay

The Bureau of Mines located and examined 292 burning coal refuse banks throughout the Nation's coal-producing regions in 1968. These coal waste fires, extending over 3,200 acres, produce poisonous, acrid gases and particulate matter that pose a threat to health and safety in the surrounding areas, damage vegetation, and cause the deterioration of nearby structures and buildings. Methods of extinguishing coal refuse fires are discussed, and an approach to eliminating future occurrences of these fires is presented.

Jan 1, 1971

By E. Chin

The countries of Asia and the Pacific, with their large mineral resource base, are significant suppliers of a wide variety of minerals to both regional and world markets. Australia, China, and India dominate the commercial mineral exploitation in the region. Australia has known reserves of major minerals, which are adequate for both domestic demand, and for exports, and is a significant producer of bauxite; copper; diamond; gold; iron ore; lead; manganese; mineral sands (titaniferrous minerals, monazite, and zircon); nickel; salt; silver; tin; uranium; and zinc. China is the world leader in proven reserves of antimony, barite, ilmenite (titanium), magnesite (magnesium), molybdenum, rare earths, and tungsten. China also has large resources of low-grade iron ore and significant resources of other mineral commodities, such as coal, based on its production and export capabilities. India has significant resources of bauxite, barite, graphite, iron ore, and mineral sands.

Jan 1, 1995

By R. E. Brewwe

"INTRODUCTION Anyone who has had frequent occasion to compare methods of analysis and testing as employed in European countries with those used in the United States has felt the need of a table or graph giving the relationship between the units of measurement of finely powdered materials. Most of the few published comparisons include only two series of sieves and often require tedious interpolations to adapt the data of one series to the series more familiar to the reader. To eliminate such deficiencies, the author hopes that the discussion and comparison of fine-series sieve sizes presented here will conserve the time of interested research workers.ACKNOWLEDGMENTSThe author is deeply indebted to Virginia B. Strathearn, scientific aide, for help in compiling the information from the literature and to W. A. Solvig, senior chemist, for valuable suggestions in preparing the manuscript.SQUARE-MESH-SIEVE SERIES OF DIFFERENT COUNTRIESSieving analyses of powdered materials have been placed on a comparable basis in different countries by the introduction and adoption of standard sieve-scale series. Series of wire-cloth square-mesh sieves in common I oratory and industrial use include: Institution of Mining and Metallurgy standard laboratory screens (I.M.M.); British Standards Institution standard for fine-mesh test sieves (B.S. or B.S.I.); Tyler standard sereer-scale sieves; United States standard sieve series; Deutsche Industrial-Nermen (DIN); and the standard control sieves of the Association Francaise de Normalisation (AFNOR). With the exception of the I.M.M. series in which the opening is equal to the diameter of the wire, the general proportions of the various series of sieves are similar. The size of British and American sieves is designated by the number of meshes or openings per linear inch or, more recently, by the number of microns per linear sieve opening. In a technical sense the word ""mesh"" is meaningless, unless the diameter of the wire is also given, so that the size of the opening can be determined. On the Continent sieves are designated either by the nunber of Mesh per linear centimeter or by the number of openings per square centimeter."

Jul 1, 1944

By A. E. Lindquist

This Bureau of Mines publication identifies areas having sufficient coal reserves to support synthetic natural gas (SNG) development and summarizes those areas having the highest potential. Capital requirements, mining and coal cost factors, water availability, and coal-quality data pertinent to SNG production are presented. Evaluation of individual coal reserve blocks was based upon coal and water requirements of the Bureau of Mines Synthane coal gasification process.

Jan 1, 1977

By Floyd R. Hertweck

The helium resources of the United States were estimated by the Bureau of Mines to be 1,037 Bcf as of January 1, 1981. These resources are divided into four categories, in decreasing degree of assurance of their existence: (1) helium in storage and in measured natural gas reserves, which totals 211 Bcf, (2) helium in indicated natural gas resources, which is estimated at 207 Bcf, (3) helium in hypothetical natural gas resources, which is estimated to be 318 Bcf, and (4) helium in speculative natural gas resources, which makes up the remaining 301 Bcf. These helium resources are further divided into depleting, nondepleting, and stored classifications, The depleting resources are those associated with natural gasfields that are, or will be, produced for the natural gas they contain. All of the helium in undiscovered (hypothetical and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 897 Bcf of the total helium resource base. Nondepleting resources are those in shut-in, abandoned, or otherwise nonproducing natural gasfields. Helium resources contained in nondepleting natural gas resources are estimated to total 100 Bcf. There is 40 Bcf of helium in storage in the Federal Government-owned Cliffside Gas Field near Amarillo, Tex.

Jan 1, 1983

By Deborah A. Kramer

An economic and technical evaluation of a proposed process to recover alumina by leaching calcined kaolinitic clay with sulfurous acid is presented in this Bureau of Mines report. After the insoluble portion of the clay has been removed by leaching, monobasic aluminum sulfite is precipitated from the pregnant leach solution by partial hydrothermal decomposition. Further heating completes the decomposition to an impure alumina hydrate. This intermediate is purified in a modified Bayer process, which includes dissolving the alumina hydrate in a caustic solution at high temperature and pressure, then decreasing the temperature and pressure to precipitate alumina trihydrate. Calcining the trihydrate produces the alumina product. A cost estimate was prepared for a plant producing 1,000 tons of alumina per day, 350 d/yr. The estimated operating cost is approximately $475 per ton of alumina. This is substantially higher than a comparable estimated operating cost for the Bayer process of $250 per ton of alumina. The proposed process does not appear economically attractive, even as a method to modify a current Bayer processing plant to use a kaolinitic clay feed. High capital costs and high energy requirements make the process prohibitively expensive.

Jan 1, 1983

By C. M. K. Boldt

The Bureau of Mines surveyed waste disposal sites at 18 metal and non-metal mines and conducted laboratory and full-scale field tests to de-termine the effects of tailings deposition techniques on physical properties of tailings pond beaches. Survey data included measurements of beach slopes, descriptions of deposition techniques, and measurements of beach physical properties taken at various distances from the point of discharge. Laboratory tests involved depositing two types of tailings, each with different grain-size distributions, into a settling trough and determining the resultant physical properties of settled materials along the length of the beach. Side confinement and the closeness of the water pool to the point of deposition caused the laboratory results to be inconclusive. Full-scale field deposition tests conducted at the tailings pond of a cooperating mine showed that there were similarities in relationships between exit velocities of tailings slurry and physical properties of the settled tailings on the beach.

Jan 1, 1988

By William T. Boyd

Foreign mining publications describing successful hydraulic mining installations, and successful domestic hydraulic mining in a gilsonite bed, have prompted the Federal Bureau of Mines to conduct a literature survey of foreign publications to determine if the hydraulic mining method can be applied to domestic coal mining. Most foreign publications do not give detailed data about the water pressures, water capacities, and production and manpower requirements for successful hydraulic mining, However, they do provide enough general data on mining conditions, manpower, and equipment used to show that conditions in many bituminous coal deposits in the United States may be favorable for economical coal extraction, using high-pressure water jets. Therefore, the Bureau proposes to conduct a field investigation to determine the most appropriate natural conditions, water pressures, and equipment for successful hydraulic mining of coal beds in the United States with variable dip, thickness, and hardness. In the past, technical personnel reviewing foreign mining reports assumed that a steeply pitching coal bed was necessary for successful hydraulic mining. Although the structure of the coal bed may be a factor in gaining assistance from overburden pressures or help in an integrated hydraulic mining and transportation system, the coal is broken mainly by the action of high-pressure, water-penetrating cracks, fissures, or cleats; therefore, the slope of the coal bed is not necessarily a determining factor in hydraulic mining.

Jan 1, 1959

By Davis E. Traut

TiC14, AIC13, and VC14 were coreduced simultaneously via a Kroll-type magnesium reduction to form an alloy sponge as part of a research effort by the Bureau of Mines to produce titanium alloy powder. Reduction tem-peratures of 750°, 850°, and 950° C, a range of chloride feed rates from 34 to 152 Ib/(ft2·h), and crucible diameters of 7-3/4 and 10-1/4 in were tested. Microprobe analyses using a 40-um-diam spot showed no effect on alloy microhomogeneity (distribution of Al and V in the Ti, considered critical as a powder property), due to changes in process variables within these ranges. Statistical analysis of these data for alloy sponge indicated greater variation in the chemical composition (AI and V) than that found in commercial Ti-6Al-4V plate or Plasma Rotating Electrode Process (PREP) powder. Therefore, a one-step approach to pow-der, such as grinding the Ti alloy sponge, would not produce a powder product of acceptable chemical homogeneity. An approach that homoge-nized the sponge, such as with a melting step, would produce an accept-able powder product with respect to chemical homogeneity.

Jan 1, 1987