Search Documents

By J. D. Davis

The carbonizing properties of No. 2-bed coal from the Bartoy mine and No. 5- or Miller-bed coal from the Wilkeson-Miller mine, both at Wilkeson, Pierce County, Wash., were determined by the Bureau of Mines-American Gas Association (BM-AGA) method. Tests were made in the 13-inch retort at 500°, 600°, and 700° C. and in the 18¬inch retort at 800°, 900°, and 1,000° C. Fischer low-temperature and United States Steel Corporation high-temperature assays were made and the results compared with those of the BM-AGA tests at corresponding temperatures. Agglutinating and plastic properties were determined, and chemical and petrographic analyses were made. The No. 2 bed is 58.5 to 88.0 inches thick at three points sampled in the Bartoy mine. The coal is 98 percent bright and contains only a trace of fusain. A composite of three mine samples contained 13.8 percent ash. The washed sample, which was used in the tests described herein, contained 11.4 percent ash, 2.2 percent moisture, and 0.6 percent sulfur upon the as-carbonized basis and 68.4 percent fixed carbon upon the dry, mineral-matter-free basis. The heating value was 15,183 B. t.u. per pound upon the moist, mineral-matter-free basis. No. 2 therefore ranks as a high-volatile A coal and is very high in that, rank. The ash softens at 2,910° F. Except for its ash content, which is higher than the limit of 9.0 percent specified by the American Society for Testing Materials, No. 2 coal fulfills the requirements of a coking coal. It also is classed as extremely friable, the friability being 88.0 percent. The agglutinating index (7.6 for the 15 : 1 ratio of silicon carbide to coal) is high, and the plasticity as indicated by the Gieseler test (60 divisions per minute) is low for a high-volatile A coal.

Jan 1, 1942

By E. S. Shedd

Misch metal was electrowon from a treated bastnasite concentrate in a REF3-LiF-BaF2 electrolyte at 950° C. The metal was prepared and tapped from a 1,000-ampere cell, and nearly 100-percent utilization of the rare-earth oxide was achieved. Prolonged operation in a smaller cell (40 amperes) indicated that the composition of the misch metal product was reasonably constant, and no significant increase of impurities, with the exception of carbon, was noted.

Jan 1, 1970

By Frank E. Cash

"INTRODUCTION The iron—ore ranges in the Lake Superior district are the Marquette in Michigan, Menominee and Gogebic in Michigan and Wisconsin, and the Cuyuna, Mesabi, and Vermilion in Minnesota. These ranges produce about 85 percent of the iron ore mined in the United States. Accident experience in connection with this production is better than that of the regions producing the remaining 15 percent. Production and shipments vary slightly from year to year but closely approximate each other over a period of years.This information circular supplements, continues, and combines the data in Information Circular 7321,2/ including figures of 1944 and 1945.During the 6—year period 1940 to 1945, inclusive, 481,485,475 long tons of iron ore was shipped from the Lake Superior district. 4/ Michigan and Wisconsin shipped 93,787,648 tons, or 19,5 percent of the total, and employed annually an average of approximately 14,300 men; Minnesota shipped 387,697,827 tons, or 80,5 percent, and employed annually an average of approximately 9,300 men. The tons produced per man employed is much greater in Minnesota than in Michigan and Wisconsin, owing to the large open-cut production in Minnesota."

Jul 1, 1947

By A. C. Burr

This progress report covers the period from January 1949 to the end of the fiscal year, June 30, 1950. Three runs were successfully completed, and one run was terminated as the result of failure of a cast reaction tube. Including the abbreviated run, the gasifier was operated for 1,915 hours, during which some 428 tons of natural and steam- dried lignite was partly gasified In producing 20 million cubic feet of gas. Gas-production rates varied from 7.8 to 16.4 thousand cubic feet per hour, the latter being the highest production rate yet reached; hydrogen-carbon monoxide ratios of the product gas varied from 1.85, the lowest ratio yet produced, to 6.5; and heat-transfer rates through the heated wall of the outer tube varied from 2,100 to 4,400 B.t.u. per square foot an hour. The general objective of the project is to establish the technology and economy of the gasification of lignite in an externally heated, metal, annular retort. Specific objectives include determination of the useful life of the metal retort tube, which is a continuing problem, and special objectives that were established for each run as part of the systematic investigation of the basic variables of the gasification process. For runs 10 and 11 the special objective was the influence of the lignite feed rate on gasification; for run 12, a comparison of dried and natural lignite, and the production of gas having a hydrogen-carbon monoxide ratio less than 2; and for run 13, the influence of a gradually increasing steam rate with steam admitted to either the upper or lower reaction zones. In addition, during each run the sulfur distribution and concentration in the product gas and char were investigated. Experimental results obtained using the lignite feed rate as the variable indicated that the gas yield per ton of natural lignite varied inversely with the feed rate. Comparison of the gasification of natural and steam-dried Dakota Star lignite indicated that the dried lignite was a superior gasification material because: 1. The hourly gas production was higher at normal combustion space temperatures under nearly equal experimental conditions. 2. On the moisture- and ash-free basis, a considerably higher feed rate could be maintained at a relatively high percentage of carbon gasified. 3. At nearly equal moisture- and ash-free feed rates, the specific gas yield was higher. The location of steam admission was found to be important because the gas yield per ton of natural lignite was higher when at least a portion of' the process steam was admitted to the upper reaction zone. Heat balances showed the potential heat in the gas and char to be 71.8 to 83.6 percent of the total heat input. The sulfur concentration in the product gas was low, being in the range of 35 to 140 grains per 100 cu. ft., of which 1.5 to 2.3 grains was organic sulfur. Careful measurements and inspection of the 310-alloy rolled plate tube following runs 11, 12, and 13 showed no excessive corrosion; however, some radial deformation had occurred indicating that deformation or creep might be the limiting factor in the life of the tube.

Jan 1, 1953

By William J. Campbell

The purpose of this investigation was to develop a rapid, accurate method of analysis for small amounts of calcium in wolframite concentrates. This analysis is necessary to determine if the wolframite concentrates meet United States National Stockpile Specification P-57R2, which limits the calcium content to 0.2 percent. Because of the small depth of the sample analyzed in fluorescent X-ray spectrography, the calcium Kaline intensity was a function of the chemical composition of the calcium-bearing particle as well as the total matrix composition. This particle-composition effect was particularly important in this analysis, as the calcium may be present as a carbonate, tungstate, phosphate, etc. Three methods of preparing the sample eliminated the variation of calcium Ka intensity with mineralogical occurrence: (1) Reduction in particle size by extensive grinding, (2) chemical fusion with sodium carbonate, and (3) solution of the calcium by an acid attack.

Jan 1, 1958

By W. S. Landers

This report presents a study by the Federal Bureau of Mines of technical factors related to the production of special carbon and tar from selected Wyoming coals. Certain Wyoming high-volatile bituminous and subbituminous coals were processed in bench-scale apparatus to determine potential carbonization yields and in pilot plant retorts to produce sufficient char and tar for testing. These tests have shown that a critical selection of coal is necessary when the coal is processed for a specialized carbon. Generally high yields of tar are obtained from low-temperature carbonization of Wyoming high-volatile bituminous and subbituminous coals, and the yield of tar usually increases with increase in rank within this range of coals. The production and evaluation of industrial carbons from Wyoming coals by using pilot plant and bench-scale techniques is part of the continuous program of upgrading western coals. It has been found that: 1. Most Wyoming coals are nonagglomerating and may be carbonized in fluidized systems. Chars produced in pilot plant retorts at low temperatures contain about 17 to 23 pct, residual volatile matter and are easily ignited. These chars appear suitable as power plant fuel. The tar-plus-light-oil yields range from 14 to 40 gal./ton of raw coal processed. 2. Wyoming high-volatile coals produce a slightly smaller and somewhat weaker coke than currently mined Western United States high-volatile coals used commercially as blending stock in metallurgical coke production.

Jan 1, 1961

By G. W. Jones

Gas analysis is of great practical value to the combustion engineer as a guide in the proper deli and operation of power and heating plants. The automotive industry, however, has made little use of gas analysis in the design and construction of engines. Tests4 made by the Bureau of Mines have shorn that for the average motor vehicle approximately 30 per cent of the heat value of the gasoline passes out in the exhaust as incomplete-combustion products. The tendency at present is to pay more attention to ease and flexibility of operation than to efficiency of combustion. However, neither condition can be fully realized except where each cylinder gets a mixture of the same composition - that is, when certain cylinders do not "load up" with gas at the expense of the others. When this occurs, due to some of the cylinders having too rich a mixture while in others it is too lean, it is impossible to get efficient combustion from the fuel used. Gas analysis enables the engineer to determine the quality of the mixture fed to the different cylinders with a high degree of precision. Briefly, the method consists in making an analysis of the exhaust gas from each cylinder while the engine is in operation.

Jan 1, 1924

By S. M. Shelton

Preliminary work in the investigation of electrolytic manganese, as reported4/, showed promise for a practical procedure of continuous production. Laboratory work was continued in the direction of process simpliication to determine an economically feasible procedure that would require a minimum of expensive equipment for plant erection and a minimum of reagent consumption for operation. Results furnished enough evidence to indicate that modifications of the process could be made leading to simplified procedure and with no sacrifice in operating efficiency. A supply of at least 200 pounds of the metal was desired for alloy research, and it was believed worth while to utilize available facilities in a search for difficulties that were not encountered in the laboratory and that might arise in larger-scale operation. Consequently, an experimental pilot plant was erected. The plant was designed for a capacity of 15 pounds per day of metal and operated under simulated plant practice.

Jan 1, 1938

This manual provides instructions for installling, operating, and maintaining protective canopies on the Joy Mfg. Co. cutter. These instructions are based upon two actual installations: one made in a mine and one in the factory. The parts list and engineering drawings for the protective canopies are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other cutters with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other cutters and can determine any necessary modifications if they are not.

Jan 1, 1973

By E. A. Barrett

The U.S. Bureau of Mines (USBM) conducted experiments to determine if training using a latent-image, three-dimensional (3-D) slide simulation exercise improved miners' ability to recognize roof and rib hazards. The effectiveness of this innovative type of classroom training was investigated by measuring workers' performance on a hazard recognition task. The study was unique in that hazard recognition skills were assessed in the workplace using actual coal mine roof and rib hazards. Results showed that training with a latent-image, 3-D slide simulation exercise significantly improved each subject's performance on the in-mine hazard recognition task. Further, the USBM researchers concluded that transfer of learning from the classroom to the workplace occurred.

Jan 1, 2010

The influence of fuel additives on automobile exhaust emissions was studied using engines currently found in the U.S. vehicle population. The fuel additives used in the experiment were four multifunctional additives and one lead antiknock additive. Experimental work was done to determine both the direct effect of the additive per se on exhaust emissions and the influence of Long-term additive effects on emissions with mileage accumulation. Results showed no significant direct or intermediate effect on exhaust emissions for any additives tested. In subsequent experimental work concerned with the long-term or indirect effects of additives, the detergent-dispersant additives were found to have little influence on emissions when used in conjunction with high-quality oil and motor fuel. The lead (tetraethyl) antiknock additive increased exhaust hydrocarbons approximately 12 to 17 percent during a 4,000-mile accumulation period using a base fuel containing 2 ml of tetraethyl lead per gallon. An unleaded fuel was used during a similar accumulation period with no significant increase in exhaust hydrocarbons with mileage.

Jan 1, 1971

By William H. King

The property of the Cupric Mines Co. is situated in the San Francisco mining district, Beaver County, Utah, 21 miles westerly from Milford (fig. 1), the rail and supply center for the area. Scheelite mineralization was not discovered until 1941, although the occurrence of lead and copper minerals had been known previously. S. VI. Hobbs, of the Federal Geological Survey, examined the Cupric property in November 1941 and prepared topographic and geologic maps of the area. This work was supplemented by additional investigations in January 1943 and March 1944 (fig. 2).

Jan 1, 1949

By E. K. Kleespies

The rate of the heterogeneous reaction between titanium-oxygen solid solutions and titanium trichloride in molten sodium chloride was determined at high temperatures. In the alpha phase, the reaction rate decreases uniformly with the increasing concentration of oxygen. The gamma crystalline form of titanium (above 33 atomic percent oxygen) was much less reactive than the alpha phase, and the reaction rate approached zero at 50 atomic percent oxygen. The activation energy for the reaction of titanium-oxygen solution containing 22.8 percent oxygen was 11.7 kcal/mole of TiCl3 as compared with 8.3 kcal/mole of TiCl3 for pure titanium.

Jan 1, 1967

By A. J. Kraemer

The properties of crude petroleum continue to interest the Bureau of Mines and constitute an important phase of its major studies on the mineral resources of the United States. The Bureau's interest in the subject has been intensified by frequent requests for information on the characteristics of crude petroleum from various producing fields. Since its inception the Bureau of Mines has collected and analyzed samples of typical oils and at present has surveyed and classified crude petroleums from nearly all the known oil fields of the Western Hemisphere. Results of these surveys have been presented in various Bureau of Mines publications. (See bibliography, appendix A, p. 145.) The nature and comparative value of crude oils from various countries and the extent to which these oils may be considered potential competitors for markets are of manifest importance to the petroleum industry in all lands, largely because all crude oils, wherever produced, are either actual or potential competitors for a market with all other crude oils. The numerous discussions of foreign production of oil that have appeared in the technical press in the past indicate the great interest of the United States in this subject.

Jan 1, 1937

By R. J. Leary

This investigation was conducted to determine the effects of various rare-earth metal addition practices upon the macrostructure and the pattern of sulfur distribution in steel ingots. Heats of plain carbon steel were melted in a 1-ton, basic electric-arc furnace. Melts were treated with mixtures of rare-earth silicides, aluminum, and cryolite either in the furnace before tap or in the ladle after tap to determine the effects of this form of rare-earth treatment upon ingot macrostructure. Steels thus treated with rare earths in the furnace were characteristically free of the gross subsurface nonmetallics which typically result from conventional rare-earth treatments. Steel treated in the ladle showed only a few such nonmetallics, and practical techniques were developed for eliminating most of these. Results showed that furnace deoxidation was controlled by the concentration ratio of rare earths: aluminum. During casting, deoxidation was controlled by the concentration of rare earths. Oxygen contents equivalent to vacuum ladle degassing resulted from air-melt furnace treatments with the rare-earth mixtures described. Rare earths in steel inhibited the onset of equiaxed grain formation during ingot freezing, and also virtually prevented interdendritic segregation of sulfides.

Jan 1, 1968

By C. Babcock

When a flat-lying mineral deposit such as a coal seam is mined, some coal is left to separate the roof and floor so that miners and machines can safely mine the seam. The mineral left is in the form of mine pillars. If too much is taken, support problems and unsafe working conditions result. If too little is taken, the mining operation will be unable to compete economically with other mines. Therefore, one must select pillars of the optimal size to maximize mining recovery and minimize risk to miners and equipment. Later, if the pillar support is no longer needed and the surface can be allowed to subside the thickness of the coal seam, then the pillar support can be removed to increase mining recovery, and initial pillar size is not as critical. Only a small part of the information available on pillar design can be presented here. The purpose of this report is to summarize some of the work done by the U.S. Bureau of Mines and others on pillar design, which is reported in the literature from 1833 to the present, and present rock mechanics test results that aid in understanding mine pillar behavior. The variable names used are those of the authors cited. This results in multiple use of some variable names.

Jan 1, 1994

By Oliver Bowles

Granites are classed as igneous rocks ; they have been formed by the solidification of rock magmas or solutions from deep within the earth . It is an almost invariable law of nature that magmas which cool quickly form fine- grained or glassy rocks , while those that cool slowly are completely crystallized and are coarser- grained . Granites , being of the latter class , are regarded as having attained their solid form at considerable depth below the surface under conditions of high temperature and pressure . The constituent minerals crystallized out slowly , the crystals interlocking with one another . The great depth of overlying rocks that must have been present when crystallization took place has been removed by erosion over large areas on the surface of the earth , in consequence of which granites appear at or near the surface in many localities . The chief minerals of which granites are formed are feldspars , quartz , and either mica or hornblende . All the essential constituents except mica are as hard as , or harder than steel , therefore granites are difficult rocks to cut and dress . Granites are usually red , pink , or gray , depending on the color of the feldspars . If hornblende or black mica is abundant the rock may be dark green or almost black . Granites are characterized by massive homogeneous texture . They are classified as fine- grained , medium- grained , or coarse - grained . Medium- grained granites are those in which the feldspar crystals average about one- fourth inch in diameter . If relatively coarsegrained crystals appear in a fine -grained ground mass the rock is designated a porphyritic granite . Uniformity in texture and grain size are desirable in building and ornamental stone , although occasionally rocks of variable texture , such as the porphyritic granites , are used . A rock may have the mineral constituents of a granite but show a banded or platy structure due to recrystallization , folding , or other changes while the rock was in a plastic or semimolten condition . Such metamorphic rocks are called granite gneisses . They are used occasionally for building purposes but not as commonly as the uniformly textured granites . - Granites are named from the most abundant mineral other than quartz and feldspar that they contain , being called , for example , biotite granite or hornblende granite . - Commercially other igneous rocks granitoid in texture but more properly classified as syenites , diorites , or gabbros may be classed as granites . Thus the " black granite " of Little Falls , Minn . , is a diorite , and the " black granite " of Eastern Pennsylvania consists of diabase or gabbro . The question is sometimes raised as to the depth to which a granite occurrence may extend . In this respect granites differ notably from limestones , sandstones , or other sedimentary rocks . The sediments were originally laid down in relatively thin beds , and individual formations providing rock of economic value may be quite limited in thickness . Usually the usable beds range between 40 and 200 feet in thickness . On the other hand , granite comes up from below . Its depth is unknown , but in general is very great . It may even be measurable in miles . The reserves of material at depth are to be measured , therefore , by the economic depth of working rather than by the vertical extent of the rock mass . Exceptionally , granites of commercial quality may occur in sills or sheets of limited thickness flanked on either side by rocks of different character , as , for example , at Westerly , R. I.

May 1, 1930

By Homer J. Ballinger

The Alma, Degraff and other mines controlled by the Mon-Ark Mining Co. comprise one of the more important groups of zinc-lead mines in Christian County, Mo. The mines were first operated in .1857 and produced more than 5 million pounds of lead from rich, shallow ore deposits. Recent exploration and development led to the discovery of zinc sulfide ore at a depth of 165 to 214 feet in the northern part of the Alma mine. After examination of these mines in September 1942 by Bureau of Mines engineers, investigation of the extension -of the Alma mine and of the depth of mineralization at the other mines appeared justified in order to encourage the production of additional zinc and lead for war purposes. Twenty-nine churn-drill holes totaling 6.463 feet of bore were completed by the. Bureau from September 1943 to January 1944.

Jan 1, 1948

By N. O. Johnson

This is one of a series of-Information Circulars dealing with mining and milling methods and costs at mines in various districts in the United States. The Hog Mountain gold mining district is of the northern edge of Tallapoosa County, in the east central part of the State of Alabama. The district is equally close to Goodwater and to Alexander City, both stations on the main line of the Central of Georgia Railroad. From Alexander City the mine is reached by 13 miles of graded road, traveling in a northeast direction. In dry seasons the road is good; in wet weather it is bad but passable. Improvements are being made constantly on the road, so that in the near future the gravel road should be good under all weathered conditions.

Jan 1, 1936

By W. P. Diamond

The explosion hazard of methane-air mixtures has become an increasingly serious mine planning problem, and an advance assessment of methane gas potential can therefore be essential for a safe and economic mine development program. As part of its coal mine health and safety program, the Bureau of Mines has developed a simple, inexpensive test to measure the methane content of coal samples obtained from exploration cores. The gas content of coal per unit weight as determined by the direct method test can be used as a basis for a preliminary estimate of mine ventilation requirements, and to determine if degasification of the coalbed in advance of mining should be considered. Since the Bureau began measuring the gas content of coal samples in 1972, experience has led to equipment and procedural changes, the most significant of which has been the development of a ball mill for crushing the coal sample to release the residual gas at the end of the desorption test period. This revised procedure replaces the crushing box and graphical methods described in earlier Bureau publications. The results of 583 direct method tests are summarized in tabular form. These results include data on the gas content of 125 coalbeds in 15 States.

Jan 1, 1980