Search Documents

By M. D. Aldridge

The results of a four-year research effort aimed at developing a practical and effective electronic system for monitoring safety conditions throughout a coal mine by displaying, at a central location, remotely measured parameters are described. This document reports on the design details of the sensor packages and the data processing program used in an experimental monitoring system. The results of special ventilation monitoring experiments and several sub-system considerations are also described.

Jan 1, 1974

By Danny Hagood

The drilling of horizontal boreholes as a means of degasification in advance of mining has been tried at Jim Walter Resources, Inc., No. 4 Mine. In a joint venture with the U.S. Bureau of Mines, a series of horizontal drainage boreholes have been drilled in the panels of an advancing continuous miner section with impressive results. The combined methane gas production rate has ranged from 205,000 to 680,000 cfd (cubic feet per day} with individual "in-seam" horizontal holes producing up to 332,000 cfd. The methane liberation from the ribs for the entire panel length has decreased from an average of 8.75 cfm (cubic feet per minute) per 100 feet of entry to 4.05 cfm per 100 feet, a 54 per cent reduction. The actual gas concentration as measure at the surface discharge point normally ranges from 85 per cent to 95 per cent methane. As a consequence of the significant reduction in methane liberation rates from the panels of the section, a 50 per cent increase in productivity from the section has been realized.

Jan 1, 1983

By Israel Liebman

The Bureau of Mines developed three types of passive water barriers for suppressing slow-moving coal dust explosions. One type is a modification of a conventional tub barrier and depends on the dynamic pressure generated ahead of an explosion to tilt the tub to release its water and suppress the explosion. The other two barriers operate in response to an increase in static pressure developed ahead of the explosion. Tests indicate the first barrier begins to release its water at air speeds as low as 50 ft/sec, and the second and third barriers will operate at a rise in static pressure as little as 0.5 psi. All three barriers were found to be effective in suppressing coal dust explosions propagating at speeds as low as 100 ft/sec. A plan is described for installing a water barrier in a working mine on a trial basis.

Jan 1, 1976

By E. D. Regad, W. E. Wallace, P. S. Mike, C. A. Hill, V. Vallyathan, M. J. Keane

"Respirable-sized quartz, a well-established fibrogenic mineral dust, is compared with kaolin in erythrocyte hemolysis assays aher treatment with saline dispersion of dipalmitoyl phosphatidylcholine, a primary phospholipid component of pulmonary surfactant. Both dusts are rendered inactive after treatment, but the membranolytic activity is partly to fully restored aher treatment with phospholipase Ai. an enzyme normally associated with cellular plasma membranes and lysosomes. Phospholipid-coated dusts were incubated for periods of 2-72 h at a series of applied enzyme concentrations, and the adsorbed lipid species and hemolytic activity were quantitated at each time for both dusts. Surfactant was lost more readily from quartz than from kaolin, with consequent more rapid restoration of mineral surface hemolytic activity for quartz. Interactions of surfactant and mineral surface functional groups responsible for the mineral-specific rate differences, and implications for determining the mineral surface bioavailability of silica and silicate dusts, are discussed. INTRODUCTIONMineral particles depositing in the lung acinus will contact an aqueous coating containing surfactant molecules spread on the air-liquid interface and dispersed within this hypophase; the primary components of that surfactant are diacyl lecithin phospholipids (King and Clements, 1972; King, 1982). Adsorption of this surfactant can suppress the cytotoxicity of mineral dusts (Marks, 1957). Suppression of hemolytic activity, a measure of membranolytic potential and an indicator of bioavailability of the mineral surface, of respirable-sized quartz and kaolin clay dusts with the adsorption of dipalmitoyl glycerophosphorylcholine or dipalmitoyl lecithin (DPL) has been measured (Wallace et al., 1985). Such contact and adsorption of pulmonary surfactant in vivo may provide a first defense system of the lung against respired dusts."

Mar 1, 1992

The purpose of this study is to develop designs to facilitate and accelerate auger rotation stoppage (and auger rotation start up so as to promote auger disengagement during auger miner repositioning) and to provide a time delay and warning signal prior to auger start up to permit any miner s near the augers to get away from the augers before they start rotating. In the underground coal mines in the U.S., there are four auger miners that are currently in use. They are the Jeffrey 100L (see Figure 1-1) and 100M (see Figure 1-2), and the Wilcox WCM and the MK20A (see Figure 1-3).

Jan 1, 1974

By Roswell W. Prouty

As part of a general plan for control and economic utilization of the waters of the Missouri River Basin as well as development of its inherent power resources, the Corps of Engineers of the United States Army has under construction a rolled earth dam near the site of old Fort Randall in South Dakota. The dam is in Charles Mix and Gregory Counties on the Missouri River at a point about 922 miles above its mouth. It is approximately 125 air-line miles southeast of Pierre and 55 miles southwest of Mitchell, S. Dak. The storage reservoir to be formed by the dam will extend upstream for 150 miles and, at maximum operating pool level, will cover an area of some 107,000 acres. It will have a storage capacity of 6.2 million acre feat.

Jun 1, 1949

By L. B. Pankratz

Heat content measurements were conducted for GaPo.996 and InPo.986 over the temperature range from 298° to 1,100° K, and for In2S2.897 over the range from 298° to 1,200° K. Both the actual experimental data and values adjusted to conform with the stoichiometric compositions (GaP, InP, and In2S3) were reported. Entropy increments above 298.15° K were calculated for the stoichiometric compounds, and heat content and heat capacity equations were derived.

Jan 1, 1965

By Thomas C. Atchison

The experimental work described in this report is part of a continuing study by the Federal Bureau of Mines of the fundamental physical processes involved in breaking rock with explosives. Six explosives were tested for their strain-producing abilities in a dolomitic marble. The explosives selected for testing had a tenfold variation in detonation pressure and a fivefold variation in characteristic impedance (product of loading density and rate of detonation). Strain pulses produced by the detonation of small charges of the explosives were recorded at distances of 5 to 130 feet. Peak strain, ?, was found to decrease with distance, R, in accordance with an exponential propagation law previously determined for other rock types, namely ? = (K/R)e ?aR The absorption constant, a, did not vary significantly with the explosive and was of the same order of magnitude as that for other rock types. The different explosives produced a fivefold variation in the value of the intercept constant, K.

Jan 1, 1961

By Floyd G. Anderson

This report reviews and summarizes information on prevention and suppression of dust in mining, tunneling, and quarrying published in the United States during the years 1958 through 1960. Unpublished pertinent data developed or assembled by the Bureau of Mines during this period also are included. Silicosis statistics reported by the U.S. Public Health Service indicate a sizable silicotic population in the United States and suggest a need for greater dust-control effort. A joint medical-environmental survey was begun by the U.S. Public Health Service and the Bureau of Mines to evaluate the magnitude of the silicosis problem in the metal mining industry in the United States.

Jan 1, 1962

By F. E. Block, T. T. Campbell, D. Z. Hobbs

Several methods were investigated for the preparation of high- purity elemental boron in an attempt to develop a feasible process for producing boron on a large scale . In the work described in this report , the metal was prepared by metering boron trichloride gas into a crucible containing molten metal reductants . It was necessary to remove reaction byproducts by acid and aqueous leaching . Magnesium and sodium were tested as reductants , but best results were achieved using lithium or zinc as reductants . Contaminants originating from the materials of construction were the chief impurities in boron made by this method . Impurities ranged from 0.5 to 5.0 percent . Impure boron ( 85 to 90 percent ) was also prepared by the magnesium reduction of boron trioxide in a thermite - type reaction . This product contained magnesium as the chief contaminant . Impure boron made in this way could be upgraded by fusing with potassium fluoborate or potassium acid fluoride . After acid leaching the fusion cake , a product containing 95 to 97 percent boron was obtained . Analytical techniques for accurate determination of impurities in elemental boron are a major problem , requiring solution before a valid comparison can be made of the quality of boron prepared by these various methods .

Jan 1, 1964

By Philip C. Good

The Bureau of Mines investigated the feasibility of utilizing low-grade phosphatic shale as a feed for phosphoric acid production. Present practice in the phosphate mining operations of southeastern Idaho is to remove and either stockpile or waste low-grade phosphatic shales as the high-grade phosphate beds are selectively mined. Acid digestion studies were performed on uncalcined shale and on shale calcined to remove free carbon to determine phosphoric acid quality, yield, and amenability to filtration. The untreated shale, containing 21.4 pct P205, was digested with sulfuric acid in a single-tank reactor to yield phosporic acid and gypsum residue. Although 96 pct P205 recovery was attained in digesting uncalcined shale, only the calcined product gave satisfactory filtration rates. Calcined shale yielded phosphoric acid recovery of about 93 pct of the contained P205. It was higher in impurities than commercially prepared acid derived from high-grade western phosphate rock. An acid filtration rate of 745 lb P205/ft2/day was attained. This value is lower than the rate of 900 lb P205/ft that is generally considered to be acceptable in industrial production of phosphoric acid from high-grade phosphate rock.

Jan 1, 1981

By F. W. Wood

A program of research was conducted by the Bureau of Mines to investigate anomalies in electrical-discharge behavior during consumable-electrode arc melting of titanium and to study the effects of these irregularities on arc-furnace explosions. A major effort was devoted to an experimental survey of arc behavior and a qualitative definition of discharge phenomena.3/ An important conclusion was that the "glow" of industrial arc-melting terminology is not a glow discharge but a skittering arc in a displaced position. The conditions that permit displaced skittering were tentatively defined. The displaced skittering arcs tended to damage melting crucibles in two ways, and details of possible mechanisms leading to crucible rupture and explosive reactions have been proposed accordingly. However, no acceptable means of preventing crucible damage was discovered.

Jan 1, 1961

By R. L. King, J. Cervik, A. A. Campoli

The Bureau of Mines performed laboratory experiments to evaluate the triboelectric effect of particulate-laden gas streams on polyethylene pipe at various velocity, humidity, dust-size, and dust-load conditions. Charges in excess of 10 kV were produced on the outside and inside surfaces of laboratory pipe samples, when exposed to 40 pct relative humidity (RH) gas stream containing coal dust. However, no charges were produced in laboratory tests that duplicated the over 75 pct RH and dust-free gas streams found in working underground pipelines. Bare cop- per wire, which is wound around the polyethylene pipe in a 1-ft (31-cm) spacing and grounded, eliminated the charge on the outside surface of the pipe, but not on the inside of the pipe surface,

Jan 1, 1986

By Will H. Coghill

The jig men of the Tri-State (Joplin-Miami) zinc district complain about the flakiness of their mill feed. They believe that the flakiness of the composite grains of gangue and mineral are to blame for losses of zinc; that is, that the flaky grains in the jig tailings have higher zinc tenor than the cubical grains. Although the evidence which follows contradicts this belief, no effort is made to give a final and conclusive answer. On the other hand, there is outlined a positive and mechanical method which the operator may use to pursue this and similar investigations. DISCUSSION OF SCREENING METHOD Hand-sorting is obviously not satisfactory for separating cubical grains from flaky grains because the personal influence can not be removed. Screens, however, may be used with success. A set of each of two types of screens is required; namely, the square-hole type and the rectangular (rectang, oblong) type. The square-hole screens must be of the double Tyler scale; that is, the order of the sieves should be after the fourth root of two instead of the customary square root of two; close sizing is important. The size of the rectang screens may be selected by trials so that a part of the material already closely sized on the square-hole screens, will pass the oblong holes. Obviously, the cubical grains will remain on the rectang and the flaky grains will pass through. Hence the mode of operation is to screen first on square-hole screens and then split the products on the oblong-hole screens.

Jan 1, 1928

By James S. Browning

The purpose of this investigation was to develop a dependable and economic method for recovering spodumene and mica from pegmatites of the type found in Gaston County, N. C. Laboratory batch tests and continuous flotation tests were made by the Federal Bureau of Mines to determine the feasibility of treating the ore by flotation to recover high-grade spodumene and mica concentrates. The spodumene flotation circuit yielded concentrates containing 6.50 percent lithia (Li20), with an overall recovery of 81.8 percent of the lithia in the ore, The mica circuit yielded concentrates containing 97.5 percent mica, with a recovery of 82.5 percent of the mica in the spodumene tailing.

Jan 1, 1961

By Louis A. Panek

Roof bolting has been known for many years, although the practice had very limited application before 1948. Since then, bolting has been introduced as a systematic method of support in more than 700 coal mines and more than 200 noncoalmines and other underground openings in rock. By far the greatest number of bolts are used to support bedded roof. This is largely because of their use in coal mines, although roof bolts are used in mining bedded deposits of all kinds -potash (New Mexico), trona (Wyoming), and ores of iron (Alabama), lead (Missouri), uranium (Utah), lead-zinc (Utah), and copper (Michigan and Arizona). Thus, bolting has been successfully employed to reinforce bedded roof under a wide range of conditions despite the limited knowledge of the principles involved. This report develops the basic principles of bolting bedded roof based on elementary beam theory and on the results of tests intended to prove or disprove certain fundamental premises. Specifically, the objectives were to gain an understanding of the function of the bolts and the behavior of bolted roof and to establish standard bolt patterns. A combination of theoretical and experimental analysis was employed. The experimental method consisted of testing mine -roof models in a centrifuge. The models, the test procedure, and the model-prototype relations are described in a companion report (1)2/. A second companion report presents a method for designing systems of vertical bolts to reinforce bedded roof (2).

Jan 1, 1956

By J. Bruce Clemmer

[Gypsum is one of the most important nonmetallic c minerals, as is indicated by the fact that the United States consumed approximately 3,500,000 tons of natural and calcined gypsum in 1937. The building trades were the largest users required 2,520,000 tons of calcine for production of plaster, wall board, tiles, block, and various other insulating and building materials. The glass and ceramic industries and other manufacturers required an additional 126,000 tons. The balance was used in the uncalcined condition as retarder in Portland cement and or agricultural purposes.]

Jan 1, 1941

By Causey J. Douglas

In 1988, at the request of the Bureau of land Management, the U.S. Bureau of Mines studied part of the 13,460-acre Owyhee Breaks Wilderness Study Area (OR-003-059) in order to evaluate its identified mineral resources. The study area is in Malheur County, OR, about 27 miles northwest of Jordan Valley. No mineral resources were identified in the study area during this investigation. There is an occurrence of jasper along Birch Creek and an associated occurrence of zeolite in some tuffs. In the northern part of the study area is an occurrence of bentonitic clay containing less than 40,000 tons. Much of the area is covered by landslide blocks, colluvium, earthflow deposits, and talus, composed of Tertiary-age volcanic rocks. The upper plateaus are capped by Tertiary-age basalt.

Jan 1, 1989

By Samuel S. M. Chan

The objective of this project was to collect information applicable to the design of ground support systems in deep mines to include in-situ rock deformations, deformation-modulus, stresses, and geology and laboratory physical properties. All data collected was to be integrated and evaluated using a finite-elements computer code. In addition, considerable professional "cross pollenization" was anticipated from the association of University and SMRC personnel. Scope of Investigation Before a ground supporting system can be evaluated, the loading conditions existing in the region of investigation, strength, deformation characteristics, as well as other engineering properties of the rock structure immediately surrounding the openings, together with the pertinent geological information, must be obtained and analyzed. It was for this reason the following items were included in this research project: (1) The selection of a suitable area for the investigation. (2) The mapping of the important geological features of the area of investigation. (3) The measurement of in-situ deformation of rock masses immediately surrounding an underground opening of the area of investigation. (4) The determination of ground stresses. (5) The obtaining of in-situ modulus of deformation of the rock masses. (6) The testing of useful engineering properties of

Jan 1, 1972

By C. J. H. Brest van Kempen

The objective of this contract was to provide thrust and torque control and visual output torque readout systems to an existing mine roof bolting machine and to test the consistency of torques obtained under actual field conditions. A Lee Norse TD1 roof bolter was modified by adding a simple torque sensing device to the drill rotation mechanism and a pneumatic logic control circuit that measures torque and controls the hydraulic circuit to the rotation motor. The modification controls and indicates the final installation torque of mine roof bolts. A total of over 5,000 mechanical roof bolts were installed in an operating coal mine. The installed torque of these bolts were within an error band (standard deviation) of 8%.

Jan 1, 1978